P1 W1MAX Desktop Modem with WiFi Function (DV-230)

Transcription

1 P1 W1MAX Desktop Modem with WiFi Function (DV-230) A) Box Contents B) Modem Overview

2 C) Modem Minimum System Requirements Operating System Hardware Software Device : Any Operating System that has been configured to operate a network card. (Windows/Linux/Mac) : Computer with at least one network card installed. : IE, Mozilla, opera or any web browser. : +12V power adapter, P1 W1MAX Modem (Provided by P1) Your P1 W!MAX Modem (DV-230) is a Plug and Play device. No configuration is needed. D) Modem Specifications This information can be found at the bottom of your P1 W1MAX Modem (DV-230). Serial Number S/N MAC Address

3 P1 W1MAX Desktop Modem (DV-230) Troubleshooting Guide MODEM SETUP 1. Plug the Power Adapter into the plug point and the Adapter s DC tip into your Modem s AC Power Port. 2. Switch on the power. Wait three seconds for the P1 Logo and all three LED lights to light up. Back View Power requirement: +12V, 1A Please use the power adaptor supplied by P1 for guaranteed performance. If the P1 Logo and all three LED lights do not light up, these are the possible problems and solutions: 1) The plug point is faulty. Switch to another plug point to confirm. 2) The AC Power Adapter is faulty. Replace your power adapter. Should the problem persist, please contact the P1 Care Line at for assistance.

4 3. Please wait 25 seconds for the Modem to boot up. The RED LED will start blinking, indicating P1 Network Initialization. If the RED LED does not start blinking after 2 minutes, please contact the P1 Care Line at for assistance. If the RED LED keeps blinking, please reposition your Modem in another direction or near a window. Ensure that the front of the Modem is facing outwards. If problem still persist, please contact P1 Care Line. 4. If your Modem is within coverage, the Yellow LED will start blinking. This indicates that the Modem is getting Authentication from the P1 Network. If the RED and YELLOW LED keeps blinking in sequence after 2 minutes, please contact our P1 Care Line at for assistance.

5 5. Once Authentication is successful, the GREEN LED will start blinking. Your Modem is requesting the DHCP IP from the P1 Network. If the Green LED keeps blinking, this indicates a problem in obtaining the DHCP IP from the P1 Network. This may be a temporary network problem. Please contact our P1 Care Line at for assistance. 1. One of the following LED lights will then remain lighted up. The type of colour indicates the signal strength. Red LED: Weak Signal Yellow LED: Good Signal Green LED: Excellent Signal Modem position guide: Condominiums/Apartments: Modem must face window Houses: Modem must be on top floor, facing window

6 6. Connect one end of the Ethernet cable to your Modem s LAN port and the other end to your computer/laptop s LAN port. The P1 W1MAX Modem (DV-230) requires a straight Ethernet Cable to work. For optimum connection, please use Ethernet cable provided by P1. 7. If the Ethernet cable is connected the LAN Blue LED will light up. The LED may blink, indicating that there is data transferring activity between your computer/laptop and the Modem. If the Blue LED does not light up: Step 1: Please check to ensure that the Ethernet Cable is connected securely. If the problem persists, proceed to Step 2. Step 2: Check if your computer s Ethernet Port is enabled and functional.

7 WIFI CONNECTION SETUP 1. Plug in the USB WiFi adapter into the modem. The USB WiFi adapter Blue LED will light up and the Blue LED will be blinking, indicating data is being transmitted. 2. Switch on the WiFi adapter on your laptop. 3. Right-click the Wireless Network Connection icon at the bottom-right of the screen and select View Available Wireless Networks.

8 4. Select the SSID that is printed on your USB WiFi adaptor. Click Connect. 5. You will be prompted to key in the WEP password. The WEP password is printed on your USB WiFi Adapter.

9 6. Once connected, ensure that your laptop has obtained the correct DHCP IP and SSID. Check for signal quality and readjust the position of your Modem accordingly Note: This step is optional. If you want to change the default SSID or WEP key, open any Internet browser and type in the URL address for Customer Web GUIDE at Username : admin Password : admin123

10 Laptop s Power Saving Schemes when running on Battery Background : Laptop s tend to have those power saving schemes so that the laptop can last longer when running on battery only. The laptop will dim down the brightness of the laptop display screen, lower down the laptop s WiFi transmitting power and shutting down or lowering down power of other functions. Troubleshooting steps: 1) In order to isolate the issue that it s not our DV230 product issue or Wimax issue, it is advisable to ask the customer when experiencing slow, intermittent or bad internet browsing experience, are they using a laptop and if yes, are they running on battery. 2) If the above are all yes, ask the customer to go to Start -> Control Panel -> System -> Hardware Click Device Manager

11 3) Go to Network Adapters and look for the laptop s WiFi driver and double click on it. 4) Go to Advanced and scroll down to look for power management and set it to the highest setting.

12

13 CONNECTIVITY ISSUES No 1. DescriptionSuggested Solution Your laptop/desktop cannoti. Ensure that the modem is switched on detect the Modem s WiFiand that the USB WiFi Adapter is Signal/SSID.properly plugged into the modem. II. Make sure that user start the wifi at networking -> Wifi at Web GUI. In addition, Disable the Hide SSID option. III. Check that your laptop/desktop has its WiFi function turned on. Ensure that it can detect WiFi 11 frequencies and is able to support B, G and B/G mix mode. IV. To ensure that it is not an issue of weak service signals, position your laptop/desktop near to the Modem. V. Make sure that the SSID you are searching for through the WiFi search network menu matches the SSID that has been set in the Modem. 2. Your laptop/desktop can detect the Modem s WiFi signal and SSID but unable to connect to it. 3. You are connected to the Modem s WiFi SSID but unable to get an IP or has limited connection. I. Ensure that you are connected to the correct SSID. II. Check your WiFi Security Mode as some security modes may require Radius Server Authentication. III. Ensure you key in the correct and matching security key/mode in the laptop/desktop and Modem. IV. Disable Access Control at the P1 W1MAX Modem (DV-230) WiFi tab on the web GUI. I. Check that you have keyed in the correct and matching security key mode in the laptop/desktop and Modem II. Check that the Modem s DHCP server is enabled at Networking -> DHCP Server. Ensure that the DHCP IP range is bigger than the amount of desktop/laptop connected to it via wired or wireless to DV230. III. Disable Access Control at the P1 W1MAX Modem (DV-230) WiFi tab on

14 the web GUI. 4. You are connected to the Modem s WiFi SSID and can an IP but cannot browse the Internet. 5. You experience irregular or slow browsing when connected through WiFi. I. Set your laptop s/desktop s Network Wireless Connection to Obtain IP automatically and Obtain DNS server address automatically. II. Ensure that your Modem is connected to W1MAX service by checking your Modem s LED lights. III. Check for proxy settings that disables your connection in your Web browser. IV. User may have to click Repair on their WiFi Network Connection for Windows OS or a similar function for other operating systems. V. Check whether you can ping to the Modem. The gateway for your laptop/desktop should have the same IP as the LAN IP for your Modem. VI. Disable Access Control at the P1 W1MAX Modem (DV-230) WiFi tab on the web GUI. I. Check whether you can ping to the Modem. The gateway for your laptop/desktop should have the same IP as the LAN IP for your Modem. II. To ensure that it is not an issue of weak service signals, position your laptop/desktop near to the Modem. III. Try changing the WiFi Channel to a different channel as it may be due to WiFi Interference. IV. Do a ping and speed test check via wired to the Modem to determine if it is a W1MAX network congestion issue.

15 COMPUTER/LAPTOP SETUP INFORMATION By default, all Operating Systems (Windows/Linux/Mac) will set the DHCP option to Obtain an IP address automatically. WINDOWS XP 1. Right-click on the My Network Places icon on your desktop and select Properties from the menu that appears. 2. In the window that appears, (labeled Network and Dial-up Connections) rightclick on the icon titled Local Area Connection and select the item Properties from the menu that appears.

16 3. A window titled Local Area Connection Properties will now appear. In the list below, select the item called Internet Protocol (TCP/IP) and click on the button labeled Properties. 4. A window titled Internet Protocol (TCP/IP) Properties will now appear. In this window, click on the radio button to the left of Obtain an IP address automatically. 5. In the same window near the bottom, make sure the radio button to the left of Obtain DNS server address automatically is filled.

17 Mac OS X This guide assumes that your computer has the network adapter and TCP/IP already installed. All Mac computers certified by Apple to run Mac OS X will have built-in Ethernet adapter hardware and the necessary networking software as part of of OS X's default installation. 1. Click on the Apple Menu Icon in the upper left corner of your screen. 2. Select System Preferences 3. Click on the Network icon.

18 4. Select the TCP/IP tab. 5. From the Configure IPv4 menu, select Using DHCP. 6. Click the Apply Now or Save button.

19 Linux (Fedora) 1. Go to the System Administration and select the Network menu item. This will launch the Network Config tool, which will prompt Configure Network Devices and Connections. 2. Select the appropriate network interface and click on Edit.

20 3. Check on the Activate device when computer starts and Allow all users to enable and disable the device. Check the Automatically obtain IP address settings and choose DHCP (these are default settings). Click on the OK button.