Technical Specifications BID NO TELESCOPIC ARTICULATING AERIAL PLATFORM LIFT (BUCKET TRUCK)

Transcription

1 Technical Specifications BID NO TELESCOPIC ARTICULATING AERIAL PLATFORM LIFT (BUCKET TRUCK) INTENT: It is the intent of these specifications is to describe a Telescopic Articulating Aerial Platform Lift mounted on a heavy duty truck chassis design for mounting of the aerial lift (Bucket Truck). The unit should have a working height of 45, height to the bottom of platform 40, horizontal reach 27 9 and include the following standard and optional features. The unit offered shall be new, unused, the current production model and conform to the specifications below The vehicle shall comply with all Federal and State of Nevada Emission Control Regulations, and Safety Standards in effect at the time of delivery to the owner. These specifications shall be construed as minimum requirements. Should the manufacturer s current published data or specifications exceed these, they shall be considered as minimum and be furnished by the bidder. TELESCOPIC ARTICULATING AERIAL LIFT SPECIFICATIONS SPECIFICATION NO. 1 PLATFORM End mounted closed 24 x 30 x 42 fiberglass platform with one step, vinyl foam cover SPECIFICATON NO. 2 PLATFORM CONTROLS Single stick control operation with safety lock out trigger (will not allow boom movement until trigger is depressed) Control valve will allow full pressure and full flow operation as well as feathering control between three control movements allowing multi-function boom movement. A start and stop functions will also be located in the platform along with an emergency stop control and emergency lowering valve. SPECIFICATION NO 3. LOWER CONTROLS Individual lower control station will be provided at turret actuate. Controls will operate all boom functions and include a selector valve to override the upper controls and a start and stop functions will also be located along with emergency stop control at this location.

2 SPECIFICATION NO. 4 HYDRAULIC PLATFORM LEVELING Hydraulic Platform Leveling System The platform leveling system can also be activated from the lower controls to adjust platform leveling, tilt the platform for cleaning, or to ease the removal on an injured operator. SPECIFICATION NO. 5 INNER BOOM ASSEMBLEY Fiberglass inner boom providing 42 in. insulation gap fully retracted meeting ANSI A requirements for Category C, 46 KV and below. Non-continuous rotation of 370 degrees. Non-lube bearings used at all pivot points SPECIFICATION NO. 6 PINS - All pins used to connect cylinder ends and rod ends will be high strength alloy steel, chrome plated for corrosion resistance. SPECIFICATION NO. 7 CYLINDERS Threaded end cap design, lower boom and extension cylinders will be equipped with two holding valves to prevent down creep and to lock booms in position in the event of a hose failure. Outer boom cylinder will be equipped with one holding valve. SPECIFICATION NO. 8 TURRET- Shall be constructed using steel plate and steel tube with ½ in. plate gussets welded for rigidity. Turret bottom shall be machined flat to support rotation bearing and include a cover for the bearing. Turret bearing will accessible lubrication points. Turret will rotate 370 degrees non continuous with a mechanical stop. A means to rotate the turret mechanically will be provided in case of hydraulic failure. SPECIFICATION NO. 9 HYDRAULIC SYSTEM 3 gpm open center hydraulic system, 15 gallon reservoir capacity with fluid level gauge, 100 mesh suction screen, 10 micron return line filter, pump pressure and flow rate will be compatible for continuous operation of the boom and optional accessories with a minimum pressure rating of 2250 psi, pump drive - transmission PTO, hoses routed internally through the boom will be high pressure non conductive with swaged hose end fitting and have protective sleeves installed at movement wear points.

3 SPECIFICATION NO. 10 ENGINE START/STOP boom will only operate when the truck is in park and the truck ignition is in the on position. Start and stop functions will also be located in the platform and at the base of the pedestal. SPECIFICATION NO. 11 SERVICE BODY Steel Zinc Coated Body w/weather Tight Doors / Long / Wide / High / Stainless Steel Rotary door Latches / Street Side Compartments 1 st Vertical adjustable shelves w/dividers / Horizontal - Shelf w/dividers / Rear Vertical Adjustable Swivel Hooks / Curb Side Compartments1st Vertical - adjustable shelves w/dividers / Horizontal - Shelf w/dividers / Rear Vertical adjustable Shelves w/dividers / Cable Rear w/grab Handle / ICC Underride Protection / Steel Tail Shelf / Two Amber Strobe Lights Curbside Front Street Side Rear / Install Front and Rear torsion Bars (Omit w/purchase of option # 1) / Provide Boom Rest On Top of Body Compartment / Paint to Match Body SPECIFICATION 12. PAINT Paint all body components with high quality white enamel SPECIFICATION 13 OPTION #1 OUTRIGGERS Install H style hydraulic outriggers W/ controls in rear tail shelf, curb side and street side SPECIFICATION 14 INSTALLATION INCLUDES THE FOLLOWING SUPPLIED AND INSTALLED Aerial device per the specifications as noted above Service body per the specifications Hydraulics components Install Torsion Bars Front and Rear (omit if option # 1 is selected) Install H style outriggers w/selection of option # 1 Back up alarm Electrical components, 12 volt DC system equipment and aerial control system Provide required warning and safety decaling Furnish 5lb ABC fire extinguisher, 3 piece triangle reflector kit and two wheel chocks Provide full body harness and lanyard Two operator s manuals and two service manuals SPECIFICATION NO. 15 ADDITIONAL: Test and certify per ANSI A92.2 and provide ANSI A92.2 data plate.

4 Provide four hours of operator training at the Town of Minden Public Works Yard. (1) One Year Warranty parts and labor SPECIFICATION NO. 16 TRUCK CHASSIS Heavy duty 4x2 regular cab 60 in cab to axle with the listed standard and optional equipment. Powertrain 6.7 V-8 OHV Power Stroke Diesel w/5 speed Automatic Transmission with PTO provision / Engine Block heater / 200 Amp Alternator / No idle engine shut down required / Limited Slip Differential Steering, Brakes and Suspension Power assist Steering / Hydraulic Brakes / Parking Brake Rear Wheels / GVW / 5600 lbs Front Axle / lbs rear Axle Comfort and Convenience Air conditioning, AM/FM Stereo w/clock, Basic Gauges, voltage monitoring on auto idle up system / Cruise Control / Tilt Steering / Trailer tow Package Seating and Interior Seating capacity of 3, split bench vinyl / Seat Color Gray Exterior Features Front license plate bracket / Chrome Bumper Package \ Trailer Tow Mirrors / Cab Color White Tires 225/70Rx19.5 Front & Rear (Traction) / Spare Tire Included SPECIFICATION NO. 17 WARRANTY CAB AND CHASSIS Basic.36 month/36,000 miles Power Train...60 month/60,000 miles Corrosion Perforation 60 month /Unlimited miles Roadside Assistance..60 month /60,000 miles Diesel Engine.60 month/100,000 miles Total net price Aerial lift, body and installation: Total net price cab and chassis: Total net price add OPTION 1. H Style Outriggers

5 Complete Total Price no options, F.O.B. Minden, NV: Complete Total Price w/option 1, F.O.B. Minden, NV Submitted by: Signature Print Name DATE: May 6th, 2013 REQUEST FOR PROPOSAL: # for the purchase of one (1) new TELESCOPIC ARTICULATING AERIAL PLATFORM LIFT (BUCKET TRUCK) with a working height of 45 NOTICE TO BIDDERS: Sealed proposals will be received at the Town of Minden Office until the date and time specified below for purchase of one (1) new TELESCOPIC ARTICULATING AERIAL PLATFORM LIFT (BUCKET TRUCK) with a working height of 45 ADDRESS PROPOSALS TO: Town of Minden Administrative Offices 1604 Esmeralda Ave Suite 101 Minden, Nevada Attention: Town Manager on or before the bid opening time and date as specified below. Proposals shall be in a sealed envelope and clearly marked on the front. Name of Bidder and Your Address Request for Proposal # for the purchase of one (1) new TELESCOPIC ARTICULATING AERIAL PLATFORM LIFT (BUCKET TRUCK) with a working height of 45 Faxed Proposals will not be accepted. PROPOSALS ARE DUE NO LATER THAN 10:00AM PACIFIC STANDARD TIME, May 28th, The Town is not responsible for delays occasioned by the U.S. Postal Service, or any other means of delivery employed by the bidder. Any bid responses received later than the date and time specified above, will be considered non responsive and will be returned unopened to the bidder. OUESTIONS: All questions or clarifications regarding this request for proposal will be answered by ing or calling: Technical specifications: General Provisions: Greg Hill Jenifer Davidson Public Works Superintendent Town Manager ghilltom@frontier.com jdavidson@co.douglas.nv.us Phone: Phone:

6 REQUEST FOR PROPOSAL # INFORMATION INCLUDING GENERAL PROVISIONS, SPECIFICATIONS AND BIDDER FORMS ARE AVAILABLE BY CONTACTING: TOWN OF MINDEN ADMINISTRATIVE OFFICES 1604 Esmeralda Ave Suite 101 Minden, Nevada PHONE: info@townofminden.com Also available on our web site: REQUEST FOR PROPOSAL BIDDERS INFORMATION: COMPANY NAME ADDRESS ADRESS CITY STATE ZIP CODE PHONE NUMBER FAX NUMBER COMPANY CONTACT

7 PLEASE NOTE ANY EXCEPTIONS, DEVIATIONS OR CHANGES TO THE SPECIFICATIONS BELOW: