ZAM40. AirWay Multizone (4 Zone) A multi zone audio distribution system designed for use with a network connected music source SM3160

Transcription

1 ZAM40 AirWay Multizone (4 Zone) A multi zone audio distribution system designed for use with a network connected music source SM3160

2 Introduction Systemline AirWay Multizone is designed to be installed into your home so that you can enjoy music from your mobile device wirelessly in any room of your choice. Each zone amplifier also has a local audio input allowing you to easily plug in the sound from a TV. The following instructions assume that you are competent in general DIY skills. You will need to locate and mount the central hub and power supply, and connect speakers and Cat5 cable to the amplifiers. If you are not confident in doing this then you should seek professional assistance. We strongly recommend that you connect the system together before installing it to ensure that you are comfortable it will all work well in your home. Specifications Multi zone hub: Dimensions: (WxHxD) 145mm x 132mm x 43mm Weight: 1.1Kg Inputs: stereo RCA Power input: +24V DC (PSM120 required) Output: balanced audio, power and data on 6 RJ45 sockets Amplifiers: Dimensions: (WxHxD): 186mm x 40mm x 106mm Weight: 0.6Kg Inputs: 1 x RJ45 balanced line and power 1 x stereo 3.5mm jack, 1 x keypad RJ45 1 x IR 3.5mm 1 x direct power input Outputs: 4 x screw fit speaker terminals 1 x 3.5mm jack pre-amp output Power supply: Dimensions: (WxDxH) 68mm x 43mm x 115mm Weight: 0.273Kg Speakers: Bass / mid driver: 140mm polypropylene cone Tweeter driver: 25mm soft-dome multi-positional Frequency response: 60Hz to 20kHz (±3dB) Power handling: 30W rms Sensitivity: 88dB/1W Impedance: 8Ω nominal Cutout: 195mm Mounting depth: 75mm Systemline, QED & uplay Plus are registered trade marks of Armour Home Electronics Ltd. ipod, ipad, iphone and itunes are registered trade marks of Apple Inc. All other product names are trademarks or registered trademarks of their respective owners.

3 Pack contents A B C ZAM40 Hub and bracket x 1 Zone amplifier module (ZAM) x 4 Power supply x 1 D E F UK mains cable x 1 Keypad x 4 3m data patch cable x 8 G H I 1m data patch cable x 4 Jack to phono audio cable x 1 Faceplate x 4 J K Plastic punch down tool x 1 CLS2 ceiling speakers x 4 pairs

4 DESIGNED IN THE UK KEYPAD DESIGNED IN THE UK KEYPAD L R SPEAKERS L R SPEAKERS DC SUPPLY A DC DC SUPPLY A DC System schematic (Standard configuration) Central location Zone 1 * * IR-REC PRE-AMP OUTPUT LINE REMOTE Local input * Source not supplied Zone 2 Apple Airport or similar device * Hard wired ethernet IR-REC PRE-AMP LINE OUTPUT REMOTE Local input Repeat for up to 6 zones * items not supplied

5 Installation instructions 1. Determine Cat5 location in each zone. One cable from the hub (A) to each amplifier (B) is required. Main location Zone 1 Max 50m Cat5 Max 50m Cat5 Zone 2 2. Mount the hub bracket on the wall and fit hub (A) in the central source location. A 3. Plug in a ZAM (B) in each zone using the Cat5 cable and patch cables (F) and (G). F G ZONE OUTPUT B ZAM40 A

6 4. Plug audio source into the hub using audio cable (H). 5. Plug power supply (C) into the hub. A A * Source not supplied H D C 6. Plug speakers (K) into the ZAM in each zone using the screw connectors. B DESIGNED IN THE UK DC SUPPLY A KEYPAD L R SPEAKERS IR-REC PRE-AMP LINE OUTPUT REMOTE DC IMO plugs included with ZAM kit K K 7. Plug TV sound into the ZAM. (Standard configuration only) LINE OUT / HEADPHONES LINE * Audio cable not supplied ZAM40 B

7 8. Connect a keypad (E) in each zone: Select a 3 metre data patch cable (F) and cut off the plug at one end only. Peel back the cut end and terminate the brown, white/brown, blue and white/blue wires to the connector as shown below. Note: do not strip off the conductor sleeving. The other four green and orange wires are not used. J E E Use the supplied punch down tool to push each cable down firmly. Note: make sure that the largest tooth of the tool is on the side of the terminal block with the coloured sticker as shown above (right). 9. Plug keypads into the ZAM in each zone. Cat5 cable KEYPAD ZAM40 E B

8 Operating instructions Make sure your audio source is playing music first. Power LED lights up red when in standby. Press the power button on the keypad to turn the zone on. Use the volume up and volume down buttons to increase or decrease the volume. Pressing the power button again switches to local source (see below) and a third press goes back to standby. The ZAM shows a blue LED indicating that the zone is on. The ZAM shows a green LED when playing from a local source. Note: The local input can be disabled on the keypad by pressing the volume up button and the power button simultaneously. Repeat this procedure to re-enable the local input.

9 DESIGNED IN THE UK KEYPAD DESIGNED IN THE UK KEYPAD L R SPEAKERS L R SPEAKERS DC SUPPLY A DC DC SUPPLY A DC Alternative configuration Central location Zone 1 IR-REC PRE-AMP OUTPUT LINE REMOTE Zone 2 IR-REC PRE-AMP LINE OUTPUT REMOTE Repeat for up to 6 zones * Source not supplied Apple Airport or similar device Hard wired ethernet

10 VOL Accessory products The following are available as additional accessories. 1. Additional ZAM units 2. Additional patch cables Expand the number of zones up to 6 by adding more ZAM units. Just add speakers and plug them in. Plug extra ZAM units in using these cables. ZAM40 M-ZAM40 - Zone amplifier module ZCAB504-1m data patch cable ZCAB507-3m data patch cable 3. Additional remote controls 4. Additional keypads M-RM1 - Infrared remote control SM0405 White SM0406 Black 5. Network music player 6. Additional speakers QE QED uplay Stream R-CLS2 - Ceiling speakers (pair)

11

12 Stortford Hall Industrial Park Dunmow Road Bishops Stortford Hertfordshire CM23 5GZ ZINS Armour Home Electronics, All rights reserved. Our policy is one of continuous product improvement, we reserve All information is given in good faith. The manufacturer accepts no responsibility for errors, omissions or incorrect assumptions. Q14758-IS_r1