Liquid Oxygen Mother Unit/ Portable Flask System.

Transcription

1 Liquid Oxygen Mother Unit/ Portable Flask System. Equipment Guide. BOC: Living Healthcare

2 02 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide. Contents. 3 The basics 4 How to fill the portable flask 6 Liquid portable flask usage chart 8 Do s & Don ts 9 Troubleshooting

3 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide. 03 IMPORTANT: Please ensure you read all accompanying literature supplied prior to using your home oxygen equipment. In particular, pay attention to the section on not smoking or allowing others to smoke near your equipment. Liquid oxygen allows the storage of larger quantities of gas more readily than normal gaseous oxygen. One litre of liquid oxygen when evaporated equals approximately 860 litres of gaseous oxygen. The liquid oxygen is vaporized into gas and warmed to room temperature inside the equipment before it is delivered to you via tubing called a cannula, which fits into your nostrils. The liquid oxygen system for homecare consists of a stationary mother unit vessel and a portable flask for holding your ambulatory oxygen. The basics. Marathon unit (Lightweight portable flask). Companion unit (Standard portable flask). We can supply liquid oxygen systems to you depending on your prescription. A full risk assessment will be carried out by our Patient Service Representative (PSR) prior to installation to check that it is safe for installation. This system gives greater flexibility and allows for an increased level of mobility. You will be supplied with a compact mother unit which contains your reserve supply of liquid oxygen. This is used to refill the small portable flask with oxygen as and when you need it. Dependent on your Home Oxygen Ordering Form (HOOF), you will be supplied one of two different portable flasks as shown above.

4 04 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide. How to fill the portable flask. a b 1. Using a clean and dry cloth, wipe the male fill connector (b) on the mother unit and the female fill connector (a) on the portable flask (supplied by your PSR). 2. Position the portable flask over the recessed area on the top of the mother unit and carefully lower the portable flask into place so that the fill connectors are properly aligned. 3. Place one or both hands on top of the portable flask and press straight down directly over the fill connector. While holding the portable flask in the fill position, pull down and hold the vent valve lever in the open position, as shown. You will hear a hissing sound keep pressing down whilst the portable flask is filling. 4. When the portable flask is full, there will be a change in the sound of the gas followed by a dense white vapour forming around the mother unit s cover. Close the vent valve by returning the vent lever to the upright position.

5 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide Disengage the portable flask from the mother unit vessel by pressing the portable release button and lifting the portable flask off the reservoir, as shown. 6. Check the contents of the portable flask by lifting the contents indicator strap, ensuring the bottom back of the unit is straight, as shown. The green bar inside the clear window indicates how full your unit is.

6 06 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide. Liquid portable flask usage chart. How long will my portable flask last? Please note the duration is only approximate and for guidance only (shown in hours unless otherwise stated). The PSR will let you know which portable flask you have been supplied. The duration is based on a full portable flask. To identify the portable flask you have been supplied, please refer to the photos page 3. Companion 1000 portable flask Flow control setting (LPM) Duration (hours) Companion 1000T (high flow) portable flask Flow control setting (LPM) Duration (hours) Marathon portable flask Continuous flow setting Flow control setting (LPM) Duration (hours) C C2 6.1 C3 4.0 C4 3.0 C5 2.4 C6 2.0 Marathon portable flask Demand flow setting Flow control setting (LPM) Duration (hours) D D D D D4 11.0

7 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide. 07

8 8 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide. Do s & Don ts. General Follow the advice we have given you about where to safely store and use your liquid oxygen vessel. Use and store your liquid oxygen base unit upright. Use the portable flask in a position as demonstrated by our PSR. Periodical hissing from either the mother unit vessel or portable flask is normal and is how the system controls its pressure. Liquid oxygen installation requires a suitable ground floor area for storage - either a secure outdoor area, a well ventilated ground floor room or outbuilding free from any oils, paints, fuels etc. Filling Always ensure the filling connections on the portable flask and mother units are clean and dry before attempting to refill the portable flask using a dry cloth. When trans-filling the portable flask, never leave it unattended until the unit is full. If the unit will not disconnect easily, never use force to remove it. Wait a few moments to allow it to thaw and then try again. Should a minor leakage occur when the portable flask is disengaged, proceed to re-engage and then disengage the portable flask. This will help to dislodge any ice or other obstruction. If a leakage is still present, engage unit again and call us immediately. Should a major leakage occur (i.e. a stream of liquid oxygen is present) when the portable flask is disengaged, stay away from the flask, ventilate the area where safe to do so and call us immediately on Replace cap on mother unit vessel fill connector when not in use. Safety Never touch any cold parts on either vessel or allow liquid oxygen to come into contact with your skin, as this could cause a serious burn. If you do receive a cold burn, immerse the affected parts in tepid water. Close valve Keep flow control valve closed when the oxygen vessel is not in use.

9 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide. 9 Troubleshooting. Symptom Possible cause Solution No flow from portable flask. Flow does not seem sufficient. Wrong indication of liquid level. Leaks when connecting the units. Problem disconnecting units. Portable flask leaking after disconnecting. 1. Flow control set to off (0). 1. Set flow to correct setting. 2. Mother unit empty. 2. Check contents gauge. 3. Tubing not fitted correctly. 3. Check the fitting of the tubing. Check tubing is not kinked. 4. Blockage of tubing. 4. Contact us on Leaks from tubing. 1. Refit tubing. 2. Incorrect setting. 2. Set flow control to prescribed flow rate. 1. Battery flat. 1. Contact us on Failure of level indication system. 2. Contact us on Dirt on connecting faces or damaged Disconnect portable flask and clean connector. faces with a clean cloth, then refit. Ice on connecting faces. Ensure vent valve is closed and allow ice to melt NATURALLY. Clean and dry connecting faces with a clean cloth after removing unit. Ice in the fill valve or damaged connector. Major leaks Stay away from unit, open windows, contact us immediately on Minor leaks Reconnect portable flask to mother unit vessel with vent valve closed. Wait two minutes. Disconnect portable flask. If leak stops, clean and dry connecting faces with a clean cloth after unit is removed. If leak continues, reconnect the portable flask with vent valve closed. Contact us immediately on

10 10 Liquid Oxygen Mother Unit/Portable Flask System. Equipment Guide. Symptom Possible cause Solution Leak of water from portable flask. Leak of water from mother unit. Duration of use from portable flask shorter than usual. Any other problem or if problem persists. Felt pad on portable flask is saturated from condensation. On the Marathon portable flask, the felt pad can be located in the bottom of the back pack. Condensate receiver full. Portable flask not filled correctly. Please contact BOC Healthcare on Empty receiver and clean it before replacing. Please contact BOC Healthcare on if this cannot be located. Refill flask and check the level indicator indicates full. Contact us on

11

12 If you are visually impaired and require a large print copy, please contact us. Contact us. Our normal working hours are Monday to Friday 8am until 5.30pm. We are open 24 hours for emergencies only. BOC Healthcare Patient Service Centre, Priestley Road, Worsley, Manchester M28 2UT, United Kingdom Tel , Fax , healthcare.home-uk@boc.com, HLC/406735/1011 The stripe symbol and the letters BOC are registered trade marks of The BOC Group Limited. Both BOC Limited and The BOC Group Limited are members of The Linde Group, the parent company of which is Linde AG. Reproduction without permission is strictly prohibited. BOC Limited 2012