READ AND SAVE THESE INSTRUCTIONS CURVA SKY. 44 & 52 Damp & Wet Location Snugger Ceiling Fan Owner's Manual

Transcription

1 READ AND SAVE THESE INSTRUCTIONS CURVA SKY 44 & 52 Damp & Wet Location Snugger Ceiling Fan Owner's Manual 44 Model Numbers for Damp Locations CF144BS00 Brushed Steel CF144CRM00 Chrome 52 Model Numbers for Damp Locations CF152BS00 Brushed Steel CF152CRM00 Chrome 44 Model Numbers for Wet Locations CF144WW00 Appliance White CF144ORB00 Oil Rubbed Bronze 52 Model Numbers for Wet Locations CF152WW00 Appliance White CF152ORB00 Oil Rubbed Bronze Net Weight: 18.5 Lbs. Net Weight: 19.4 Lbs. Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday Part No. F40BP Revision: Form No. BP7407-3

2 READ AND SAVE THESE INSTRUCTIONS Safety Instructions TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: a. Use this unit only in a manner intended by the manufacturer. If you have questions, contact the manufacturer. b. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 1. Read your owner s manual carefully and keep it for future reference. 2. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn off the power to the ceiling fan before servicing. 3. Do not put anything into the fan blades while they are turning. 4. Do not operate reversing switch until fan blades have come to a complete stop. Additional Safety Instructions for Installation 1. To avoid possible shock, be sure electricity is turned off at the fuse box before wiring, and do not operate fan without blades. 2. All wiring must be in accordance with the National Electrical Code ANSI/NFPA and Local Electrical Codes. Use the National Electrical Code if Local Codes do not exist. The ceiling fan must be grounded as a precaution against possible electrical shock. Electrical installation should be made or approved by a licensed electrician. 3. The outlet box and joist must be securely mounted and capable of reliably supporting at least 50 pounds. Use only U.L. outlet boxes listed as Acceptable for Fan Support of 22.7 kg. (50 lbs.) or less, and use the mounting screws provided with the outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. 4. The downrod furnished with the fan provides the minimum recommended floor to fan blade clearance for an 8 foot ceiling. 5. The fan must be mounted with the fan blades at least 7 feet from the floor to prevent accidental contact with the fan blades. 6. Follow the recommended instructions for the proper method of wiring your ceiling fan. If you do not know enough about electrical wiring, have your fan installed by a licensed electrician. : To reduce the risk of electrical shock, this fan must be installed with an isolating wall control/switch. NOTE: This fan is suitable for use with solid-state speed controls. : To reduce the risk of fire or electric shock, this fan should only be used with fan speed control Model No. UC8013R, manufactured by Rhine Electric Co., Ltd. : This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson could result in personal injury or property damage. : To reduce the risk of personal injury, do not bend the blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. NOTE: All setscrews must be checked and re-tightened where necessary before installation. DATE CODE: The date code of this fan may be found on the box, stamped in ink on a white label. You should record this data above and keep it in a safe place for future use. 2

3 Unpacking Instructions PACKAGE CONTENTS Do not install or use fan if any part is damaged or missing. Call Toll-Free: This product is designed to use only those parts supplied with this product and/or any accessories designated specifically for use with this product by Emerson Electric Co. Substitution of parts or accessories not designated for use with this product by Emerson Electric Co. could result in personal injury or property damage. 1. Open carton containing fan. Remove top half of styrofoam unit. Remove parts and check to see that you have received the following parts: NOTE: If you are uncertain of part description, refer to exploded view illustration. NOTE: Place the parts from the loose parts bags in a small container to keep them from being lost. If any parts are missing, contact your local retailer or catalog outlet for replacement before proceeding. HARDWARE CONTENTS Part Description Quantity A Fan Motor Assembly 1 B Ceiling Trim Ring 1 C Ceiling Mounting Plate 1 D Fan Blades 3 E Lower Housing 1 F Light Kit Plate 1 G Glass Shade 1 H No-Light Cover Plate 1 I 6-Speed Electronic Receiver Control with Parts Bag 1 J 6-Speed Handheld Transmitter with Wall Bracket 1 K 50-Watt Halogen Mini Candelabra Bulbs 2 A E F G Part Description Quantity 1 Wire Connectors, 12 ga. 3 2 M5 x 16mm Flange Head Blade Screws 10 3 M5 x 10mm Pan Head Ceiling Cover Screw with Washer (spare) 1 4 M4 x 10mm Pan Head Screw for Lower Housing and Light Kit (spare) 1 5 Blade Balance Kit 1 B C J H I D K Remove the fan motor assembly from the protective plastic bag. Place all carton contents on a protective surface. PROTECTIVE PLASTIC BAG 5 3 emersonfans.com Please contact for further assistance

4 THE FAN MODELS CF144BS, CF144CRM, CF152BS & CF152CRM ARE SUITABLE FOR DAMP LOCATIONS SUCH AS COVERED PORCHES, COVERED PATIOS, AND COVERED DECKS...ANYWHERE THERE IS A ROOF OVERHEAD. THE FAN MODELS CF144WW, CF144ORB, CF152WW & CF152ORB ARE SUITABLE FOR WET LOCATIONS SUCH AS PORCHES, PATIOS, AND DECKS. This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One wire stripper Materials One stepladder Wiring outlet box and box connectors must be of type required by the local code. The minimum wire would be a 3-conductor (2-wire with ground) of following size: Installed Wire Length Wire Size A.W.G. Up to 50 ft ft. 12 Before assembling your ceiling fan, refer to section on proper method of wiring your fan (page 7). If you feel you do not have enough wiring knowledge or experience, have your fan installed by a licensed electrician. Electrical Requirements IMPORTANT: Your ceiling fan will not function properly, and may be damaged, if used with any wall dimmer switch or control other than the Emerson Electric Fan/Light Remote Control supplied with the fan. Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked Acceptable for Fan Support of 22.7 kg. (50 lbs.) or less, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. To avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician. 4

5 Ceiling Fan Assembly General Your Emerson ceiling fan comes supplied with a Fan/Light Remote Control which consists of a receiver mounted inside the ceiling cover of the fan motor housing. This system allows you to regulate your ceiling fan speed and light intensity. 1. Position the fan motor assembly upside down in preparation for mounting the three fan blades. 2. Slide blade through blade slot in fan housing assembly. Mount blade to fan housing using three M5 x 16mm flange head blade screws (Figure 1). NOTE: Take care not to scratch fan housing assembly when installing blades. 3. Complete the remaining two blades installation per the above instructions. FAN BLADE Figure 1 SLIDE FAN BLADE INTO BLADE CENTER SLOT REMOVE M4 x 10mm PAN HEAD SCREW M5 x 16mm FLANGE HEAD BLADE SCREWS (3 per blade) FAN HOUSING LOWER HOUSING BLADE SLOT 4. Remove one of the three screws in the motor housing assembly and loosen the remaining two screws (Figure 2). 5. Attach the lower housing assembly to the fan motor using the two key slot holes (Figure 2). Secure the lower housing assembly by tightening the two screws. Reinstall the screw that was previously removed. 6. Remove and retain the wire connectors from the white and blue wires. Figure 2 LIGHT KIT BLACK KEY HOLE SLOT (2) To avoid possible fire or shock, the connectors should not be removed unless immediately installing the light kit. Power should be turned off prior to connector removal and light kit installation. 7. Connect the white wire from the ceiling fan to the white wire of the light kit plate (Figure 3). Connect the blue wire from the ceiling fan to the black wire of the light kit plate. Use wire connectors (previously removed) to make connections. 8. Remove one of the three screws in the lower housing and loosen the remaining two screws (Figure 3). 9. Tuck the wires and connectors into the fan housing. Position the light kit plate into the fan housing by placing the cut out notches over the fan housing dimples (Figure 4). NOTE: Make sure all wires and connectors are tucked under the light kit plate and not pinched between light kit plate and fan housing. 10. Attach the light kit plate assembly to the lower housing using two key slot holes (Figure 4). Secure the light kit plate assembly by tightening the two screws. Reinstall the screw that was previously removed. Figure 3 LIGHT KIT WHITE REMOVE ONE LOWER HOUSING SCREW FAN MOTOR BLUE FAN MOTOR WHITE LOWER HOUSING KEY HOLE SLOT (2) REMOVE M4 x 10mm PAN HEAD SCREW CUT OUT NOTCHES DIMPLES LIGHT KIT PLATE 5 Figure 4 emersonfans.com Please contact for further assistance

6 How to Hang Your Ceiling Fan The fan must be hung with at least 7' of clearance from floor to blades (Figure 5). CEILING The outlet box and joist must be securely mounted and capable of supporting at least 50 lbs. Use only a U.L. outlet box listed as Acceptable for Fan Support of 22.7 kg. (50 lbs.) or less. AT LEAST 7' To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked Acceptable for Fan Support of 22.7 kg. (50 lbs.) or less, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. Figure 5 FLOOR OUTLET BOX 1. Disconnect electrical power to the branch circuit at the circuit breaker or fuse box before attempting to install the ceiling fan mounting plate on the outlet box. CEILING MOUNTING PLATE Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. 2. Pull the electrical supply black, white and ground wires through the center opening of the ceiling mounting plate before securing the plate to the outlet box (Figure 6). 3. Position the ceiling mounting plate onto the outlet box and secure using the two outlet box screws, supplied with outlet box (Figure 6). 4. Slide the ceiling trim ring over the fan motor assembly and let it rest on the motor assembly (Figure 7). 5. Place the motor assembly onto the ceiling mounting plate hook during wiring fan motor assembly to outlet box (Figure 8). Figure 6 FAN MOTOR ASSEMBLY CEILING TRIM RING Figure 7 CEILING MOUNTING PLATE OUTLET BOX SCREWS (2) CEILING MOUNTING PLATE HOOK HOOK FAN MOTOR ASSEMBLY Figure 8 6

7 How to Wire Your Ceiling Fan If you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock. CAUTION: To reduce the risk of electrical shock, disconnect the electrical supply circuit before installing the fan, light kit or receiver. NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. 1. Position the receiver into the fan motor housing as shown in Figure Refer to Figures 9 and 10 to connect the receiver wires to the supply wires and the fan motor wires using the wire connectors supplied with the fan as follows: a. Securely connect the green grounding wire from the ceiling mounting plate and green grounding wire from fan body to the supply green grounding conductor (this may be a bare wire or a wire with green insulation). b. Securely connect the supply white (neutral) wire to the receiver white (AC IN N)/(TO MOTOR N) wire and white (neutral) fan wire. c. Securely connect the supply black wire to the receiver black/white (AC IN L) wire. d. Securely connect the fan motor black wire to the receiver black (TO MOTOR L) wire. e. Securely connect the fan motor blue wire to the receiver blue (FOR BOTTOM LIGHT) wire. Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors, except for the ground wire. Do not operate fan until blades are in place. Noise and fan damage could result. Figure 9 WHITE RECEIVER FAN ASSEMBLY GREEN ANTENNA BLACK RECEIVER BLACK/WHITE RECEIVER WHITE FAN BLACK FAN Figure 10 RECEIVER BLACK SUPPLY SUPPLY & CEILING MOUNTING PLATE GREEN S SUPPLY, RECEIVER & FAN WHITE S SUPPLY BLACK RECEIVER BLACK/WHITE FAN & RECEIVER BLUE S FAN BLACK GREEN GROUND RECEIVER BLACK RECEIVER WHITE SUPPLY BLUE RECEIVER BLUE FAN GREEN MOUNTING PLATE GREEN FAN 7 emersonfans.com Please contact for further assistance

8 How to Wire Your Ceiling Fan (continued) 3. After connections have been made, turn leads upward and carefully push leads into the outlet box, with the white and green leads on one side of the outlet box and the black and blue leads on the other inside of the outlet box. 4. Remove one of the four screws in the ceiling mounting plate and loosen the remaining three screws (Figure 11). 5. Unhook the fan motor housing from the ceiling mounting plate hook and lift the fan motor housing assembly up to the ceiling mounting plate. Align and engage the motor assembly slots with the three screw heads previously loosened by rotating the fan motor housing assembly to engage the screw heads and all three slots. Install the previously removed M5 x 10mm screw and secure the assembly to the plate (Figure 11). Completely tighten all four screws. Figure 11 CEILING MOUNTING PLATE M5 x 10mm PAN HEAD CEILING COVER SCREWS CEILING COVER SCREW HEADS (4) FAN MOTOR HOUSING ASSEMBLY To avoid possible fire or shock, make sure that the electrical wires are completely inside the outlet box and not pinched between the ceiling mounting plate and the fan motor housing assembly. 6. Position the ceiling trim ring over each of the protruding ceiling cover screw heads and rotate the ceiling trim ring clockwise to secure (Figure 12). Figure 12 CEILING TRIM RING FAN MOTOR HOUSING ASSEMBLY How to Assemble Your Light Kit Glass Shade 1. Screw in two 50-watt (maximum) halogen mini candelabra base bulbs in the light kit plate sockets (Figure 13). 2. Place the glass shade into the opening in the fan motor housing assembly, aligning the three flat areas on the top edge of the glass with the three raised dimples on the fan motor housing assembly and turn the glass shade clockwise until it stops (Figure 14). NOTE: periodically check that the glass shade is seated fully clockwise in the fan motor housing assembly. DIMPLES (3) FLAT AREA (3) GLASS BOWL 50-WATT (maximum) HALOGEN MINI CANDELABRA BASE BULBS (2) Figure 13 LIGHT KIT PLATE SOCKETS (2) Figure 14 8

9 How to Assemble Your No Light Cover Plate Do not install any light bulbs into the light kit plate if using the cover plate. Installation of light bulbs when using the cover plate could result in fire, shock and serious personal injury. DO NOT INSTALL LIGHT BULBS WHEN USING THE COVER PLATE 1. Place the cover plate onto the lower housing aligning the three flat areas on the top flange of the cover plate with the three pins on the inside of the fan motor housing assembly (Figure 15). Then turn the cover plate clockwise until it stops turning. 2. Your cover plate is now installed DIMPLES (3) FLAT AREA (3) COVER PLATE Figure 15 Remote Control Procedures General Your Emerson Ceiling Fan/Light Remote Control consists of hand-held transmitter and a receiver which is mounted under the fan ceiling cover. The remote control is designed to separately control your ceiling fan speed and light intensity. The remote control transmitter is powered by two AAA alkaline batteries (included). To prevent possible damage if the batteries should leak, be sure to remove the batteries when the control is not to be used for an extended period of time. Code switches in the transmitter and receiver may be set in 32 different positions. If your fan and light go on and off without using your control, you may be getting interference from other remote units such as garage door openers, car alarms or security systems. To remedy this situations, simply change the combination code in your transmitter and receiver. Preset Memory Feature Your Emerson receiver is equipped with a preset memory feature. If the AC supply to the receiver is powered through a wall switch, when the switch is turned OFF, the control will remember the light intensity and fan speed. When the switch is turned back ON the light and fan will resume operation as they were prior to the switch being turned OFF. Installation of Battery 1. Remove the battery cover by pressing firmly below the arrow and sliding the cover off the control (Figure 16). 2. Install two AAA alkaline batteries and reinstall the battery cover. Figure 16 TWO AAA BATTERIES BATTERY COMPARTME NT COVER REMOTE CONTROL LEVERS CODE SWITCHES REMOTE CONTROL 9 emersonfans.com Please contact for further assistance

10 Remote Control Procedures (continued) Installation of Storage Bracket for Remote Control A storage bracket is provided for holding your remote control when not in use. If you desire to use the bracket, install it on a wall that is away from excess heat or humidity (Figure 17). TO INSTALL BRACKET TO WALL: SLIDE THE COVER UP TO EXPOSE THE SCREW HOLES FOR INSTALLATION COVER WALL BRACKET Figure 17 SCREW HOLES (2) Setting Operating Frequency of Remote Control Your remote control has code switches which must be set in one of 32 possible code combinations (Figure 16). The five levers (numbered 1, 2, 3, 4, and 5) on the switches are factory-set in the ON (up) position. Change the switch settings as follows (Figure 18): 1. Slide the five switch levers in the remote control to your choice of ON (up) or down positions. Use a ballpoint pen or small screwdriver and slide the levers firmly up or down. 2. When power is restored, push and hold the fan OFF button ( ) for 3 to 5 seconds to set the code in the receiver. 3. If airflow is desired in the opposite direction, press the ( ) button on the remote control. The fan must be operating at any speed for the reverse button to function. The blades will turn in the opposite direction and reverse the airflow. 4. To set the desired fan speed, press the ( ) button to decrease the speed and the ( ) to increase the speed. The LED display will light up to indicate the new speed selected. 5. To turn the downlight on, press and release the ( ) button. The light will turn on at the light intensity previously selected. 6. To vary the intensity of the light, hold the ( ) button down until the desired light intensity is reached, then release the button. 7. The sixth switch marked ON and I is for dimming control of lights: Set switch to ON to allow for dimming of the lights. Set switch to I for no dimming of the lights such as for fluorescent bulbs. Figure 18 10

11 Maintenance IMPORTANT CARE INSTRUCTIONS for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish. Abrasive cleaning agents are not required and should be avoided to prevent damage to finish. Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. Accessories 1. Downrod Extension Kits (see store or catalog). 2. Ceiling Fan Controls (see store or catalog). The use of any other control not specifically approved for this fan could result in fire, shock and personal injury. To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked Acceptable for Fan Support of 22.7 kg. (50 lbs.) or less, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt. Light Kit Circuit Breaker - Canada Only In accordance with Federal Law, this ceiling fan is equipped with a light kit circuit breaker. Using halogen light bulbs with greater than 50 watts rating will cause the breaker to activate. If this occurs, shut off the electricity to the ceiling fan and check that the lamps are each 50W maximum. The light kit circuit breaker will automatically reset when the electricity is turned off and then back on. INSTRUCTION TO THE USER (if device contains a digital device) This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. This equipment has been certified to comply with the limits for a class B computing device, pursuant to FCC Rules. In order to maintain compliance with FCC regulations, shielded cables must be used with this equipment. Operation with non-approved equipment or unshielded cables is likely to result in interference to radio and TV reception. The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user s authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. 11 emersonfans.com Please contact for further assistance

12 Repair Parts (Canada Only) " 9-44" Energy Efficient Use of Ceiling Fans Ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure quality and product performance. Choosing the Appropriate Mounting Location. Ceiling fans should be installed, or mounted, in the middle of the room and at least 7 feet above the floor and 18 inches from the walls. If ceiling height allows, install the fan 8-9 feet above the floor for optimal airflow. Consult your Emerson Retailer for optional mounting accessories. Using the Ceiling Fan Year Round. In the summer, use the ceiling fan in the counter-clockwise direction. The airflow produced by the ceiling fan creates a windchill effect, making you "feel" cooler. Select a fan speed that provides a comfortable breeze, lower speeds consume less energy. In the winter, reverse the motor and operate the ceiling fan at low speed in the clockwise direction. This produces a gentle updraft, which forces warm air near the ceiling down into the occupied space. Remember to adjust your thermostat when using your ceiling fan - additional energy and dollar savings could be realized with this simple step Turn Off When Not in the Room. Ceiling fans cool people, not rooms. If the room is unoccupied, turn off the ceiling fan to save energy. 12

13 Repair Parts Listing Damp Part Numbers Wet Part Numbers Key Model No. Model No. Model No. Model No. Model No. Model No. Model No. Model No. No. Description CF144BS00 CF152BS00 CF144CRM00 CF152CRM00 CF144WW00 CF152WW00 CF144ORB00 CF152ORB00 1 Ceiling Mounting Plate Ceiling Trim Ring BS BS CRM CRM WW WW ORB ORB 3 Ceiling Cover BS BS CRM CRM WW WW ORB ORB 4 Lower Housing BS BS CRM CRM WW WW ORB ORB 5 Light Kit Plate Assembly Glass Shade OM OM OM OM OM OM OM OM 7 No Light Kit Cover BS BS CRM CRM WW WW ORB ORB 8 52 Blade Assembly BS BS WW ORB 9 44 Blade Assembly BS BS WW ORB 10 Harness, Wiring - Reverse Modular & Aux. Capacitor Handheld Transmitter Electronic Receiver with Wire Connectors * Parts Bag, Containing: Connector, Wire, 12 Ga. (3) 14 Screw, Pan Head, Ceiling Cover, M5 x 10mm (1) 15 Screw, Flange Head, Blade M5 x 16mm (10) 16 Screw, Serrated Head, Lower Housing/ Light Kit, M4 x 10mm (1) 17 Kit, Balancing W Circuit Breaker Owner's Manual BP BP BP BP BP BP BP BP Before discarding packaging material, be certain all parts have been removed. HOW TO ORDER REPAIR PARTS WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: PART NUMBER NAME OF ITEM PART DESCRIPTION MODEL NUMBER The model number of your Fan will be found on a label attached to the top housing. For repair parts, phone emersonfans.com Please contact for further assistance

14 Trouble Shooting : FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. start. : Make sure main power is turned off. 2. Loose power line connections to the fan. 2. Check line power connections to fan. 3. Fan/Light remote control is OFF. 3. Turn ON Fan/Light remote control. 2. Fan sounds 1. Blades not attached to fan. 1. Attach blades to fan before operating. noisy. 2. Screws securing fan blades to motor are loose. 2. Check to make sure the screws which attach the blades to the motor are tight. : Make sure main power is turned off. 3. Fan wobbles 1. Screws securing fan blades to motor are loose. 1. Check to be sure screws which attach the fan blade to the excessively. motor are tight. 2. Fan blades are not seated properly. 2. Check to be sure that the screws securing the fan blades seat firmly. 3. Fan blades out of balance. 3. Interchanging an adjacent (side by-side) blade pair can redistribute the weight and result in smoother operation. Or use supplied balancing kit to balance blades. 4. Both lamps will 1. Loose electrical connectors. 1. Shut off the branch circuit electricity at the fuse box or not illuminate. breaker panel and check the receiver electrical connectors for proper installation. 2. Remote control battery is weak. 2. Replace the AAA remote batteries. 3. The lamps are burnt out. 3. Turn the electricity off and replace the lamps with new 50W max. lamps. 4. Lamps turn on and then turn off. 4. The built in circuit breaker is tripping, check that the lamps are each 50W maximum. CAUTION: Turn the lights off before touching halogen lamps, they are very hot and can burn your fingers. Remote Control Trouble Shooting Fan/Light Fails to Operate Check that the speed switch on the fan is set to HIGH (...) speed. Check that the light switch is on. Check that the battery is good (red indicator light should light when any button is pressed). Check that the receiver is wired properly. Check that code switches in the remote control and receiver are set in the same position. Short Range If the remote control operates the fan when close to it, but does not operate it at a distance of 40 feet, try placing the antenna wire outside of the ceiling cover. 14

15 Emerson Air Comfort Ceiling Fan Limited Warranty What The Limited Warranty Covers: This limited warranty is offered by Air Comfort Products division of Emerson Electric Co. ("Emerson" "we" or "us") located at the address stated below to the original retail purchaser ("you" or "your") of an Emerson Air Comfort Ceiling Fan product ("Emerson Ceiling Fan") and covers the motor and the other components and accessories of the Emerson Ceiling Fan against all defects in workmanship and materials. What The Period Of Coverage Is: This limited warranty will cover the Emerson Ceiling Fan motor for the expected lifetime of your Emerson Ceiling Fan (when operated in accordance with your Owner's Manual or other instructions provided by Emerson to you with the Emerson Ceiling Fan). All other components and accessories of the Emerson Ceiling Fan are covered by this limited warranty for a period of one (1) year from its date of original retail purchase. ANY IMPLIED WARRANTY, INCLUDING WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE THAT IS AVAILABLE TO YOU UNDER THE LAWS OF YOUR STATE OR PROVINCE SHALL COVER THE MOTOR FOR THE EXPECTED LIFETIME OF THE MOTOR (SUBJECT TO PROPER USE), AND FOR ONE YEAR WITH RESPECT TO COMPONENTS AND ACCESSORIES. No Other Express or Implied Warranty Applies: THE LIMITED WARRANTIES PROVIDED ABOVE ARE THE SOLE AND EXCLUSIVE WARRANTIES PROVIDED BY EMERSON TO YOU FOR YOUR EMERSON CEILING FAN, AND ARE IN LIEU OF ALL OTHER WARRANTIES, WRITTEN OR ORAL, EXPRESS OR IMPLIED, WHETHER ARISING BY OPERATION OF LAW OR OTHERWISE, WHETHER OR NOT THE PURPOSE HAS BEEN DISCLOSED AND WHETHER OR NOT THE EMERSON CEILING FAN HAS BEEN SPECIFICALLY DESIGNED OR MANUFACTURED FOR YOUR USE OR PURPOSE. EMERSON HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR COMPONENTS AND ACCESSORIES AS OF THE EXPIRATION OF THE ONE YEAR WARRANTY PERIOD FOR SUCH COMPONENTS AND ACCESSORIES. IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE FOR THE MOTOR PORTION OF THE EMERSON CEILING FAN ARE LIKEWISE DISCLAIMED BY EMERSON AT SUCH TIME THAT THE EXPECTED LIFETIME OF THE EMERSON CEILING FAN UNDER NORMAL USAGE HAS BEEN REACHED. EXCLUSIONS OR LIMITATIONS OF IMPLIED WARRANTIES MAY VARY FROM STATE TO STATE AND PROVINCE TO PROVINCE SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. What We Will Do To Correct Problems: If during the one (1) year warranty period the motor or any component or accessory of your Emerson Ceiling Fan is defective in materials or workmanship, or if during the expected lifetime of the Emerson Ceiling Fan (when used in accordance with the User Manual or other instructions) the motor is defective in materials or workmanship, you must contact Emerson during the applicable warranty period. If the defect is covered by warranty, Emerson will repair or replace the defective motor, component or other accessory at no charge to you. If repair of the motor, component or accessory is not practical or possible within a reasonable time and no replacement Emerson Ceiling Fan can be provided, Emerson will refund to you the actual purchase price of your Emerson Ceiling Fan. We will ship the repaired or the replacement Emerson Ceiling Fan to you at no charge, but you are responsible for all costs of removal and reinstallation of your Emerson Ceiling Fan. How You Can Receive Warranty Service: You must be the original retail purchaser and have proof of your purchase of the Emerson Ceiling Fan to obtain your remedy under this limited warranty. You can return your Emerson Ceiling Fan to your place of purchase, or you can call Emerson Customer Service at to obtain a return authorization and service identification tag. In order for us to confirm that your Emerson Ceiling Fan is still under warranty, please retain your receipt or other proof of purchase and have that information readily available when returning your Emerson Ceiling Fan to your place of purchase, or upon calling Emerson Customer Service. If you call Emerson Customer Service, prior to your call please be prepared to provide all model numbers shown on your Emerson Ceiling Fan. Once we have processed your return authorization request, we will provide you with a postage paid return label which should be affixed to the Emerson Ceiling Fan package you ship to the address listed at the end of this limited warranty. The return label will be sent to the mailing address you provide to us by phone. What Is Not Covered: This limited warranty does not extend to and expressly excludes: The glass globes and light bulbs of your Emerson Ceiling Fan, Loss or damage to the motor or any component or accessory caused by normal wear and tear, rather than due to defects in materials or workmanship, Loss or damage resulting from conditions beyond our reasonable control, including without limitation, repairs not made at our factory or authorized service center, use of parts or accessories not provided to you as part of this warranty by our factory or authorized service center, mishandling, unreasonable use, misuse, abuse, modifications or other damage caused by you or a third party to your Emerson Ceiling Fan while not in our possession, Loss or damage resulting from improper installation, or other failure to comply with instructions in your Owner's Manual. This limited warranty is deemed null and void upon the occurrence of either of the following events: You cease to own the Emerson Ceiling Fan product, or The Emerson Ceiling Fan is moved from its original point of installation. This limited warranty is only valid within the 50 United States, the District of Columbia, and Canada. No other written or oral warranties apply, and no employee, agent, dealer or other person is authorized to give any warranties on behalf of Air Comfort Products or Emerson Electric Co. Limitation of Liability REPAIR, REPLACEMENT OR A REFUND ARE THE EXCLUSIVE REMEDIES AVAILABLE TO YOU UNDER THIS LIMITED WARRANTY. TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL EMERSON OR ANY EMERSON AUTHORIZED DEALER BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE, USE, MISUSE OR INABILITY TO USE THE EMERSON CEILING FAN OR FOR THE NEGLIGENCE OF EMERSON OR AN EMERSON AUTHORIZED DEALER. EMERSON SHALL NOT BE LIABLE FOR DAMAGES CAUSED BY DELAY IN PERFORMANCE AND IN NO EVENT, REGARDLESS OF THE FORM OF THE CLAIM OR CAUSE OF ACTION (WHETHER BASED IN CONTRACT, INFRINGEMENT, NEGLIGENCE, STRICT LIABILITY, OTHER TORT OR OTHERWISE), SHALL EMERSON'S OR ANY EMERSON AUTHORIZED AGENT'S LIABILITY TO YOU OR ANY INDIVIDUAL USING THE EMERSON CEILING FAN EXCEED THE PRICE PAID BY THE ORIGINAL OWNER FOR THE EMERSON CEILING FAN. The term "consequential damages" shall include, but not be limited to, loss of anticipated profits, business interruption, loss of use or revenue, cost of capital or loss or damage to property or equipment. How State and Provincial Law Relates To The Warranty: Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above exclusion or limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. 15 emersonfans.com Please contact for further assistance

16 Air Comfort Products DIVISION OF EMERSON ELECTRIC CO W. Florissant St. Louis, MO Questions, problems, missing parts: Before returning to the store call Emerson Electric Customer Service 8 a.m. - 6 p.m., EST, Monday-Friday Retain this manual for future use. Part No. F40BP Revision: Printed in China 02/13 Form No. BP7407-3