Exam Name: Ethernet Switching Exam Type: Nortel Exam Code: Doc Type: Q & A with Explanations Total Questions: 61

Transcription

1 Question: 1 The exhibit shows VLANs spanning two Ethernet Routing Switch 5510/5520s. Both port 14 on S1 and port 13 on S2, identified by the red arrow, are tagged members of VLAN 1 and VLAN 2. How is this configured? A. By ensuring that the tagging checkbox is checked on the configuration screens for VLAN 1 and VLAN 2. B. By enabling 802.1Q tagging on both port 14 of S1 and port 13 of S2. C. This VLAN configuration is incorrect and must be configured differently to work. D. Tagging is automatically configured because port 13 of S2 is already in VLAN 1. Question: 2 You recently reset an Ethernet Routing Switch 5510 using 4.1 code to the factory default settings. You want to upgrade the code for the 5510 but do not have a console cable to do it. Which IP address must you use to perform this task? A /24 B /24 C /24 D /24 Question: 3 Company.com wants port mirroring configured on an Ethernet Switch T. They want port 23 configured as the monitor port to monitor all traffic received and transmitted between a workstation on port 24 (port Y) and a workstation on port 25 (port X). Once you access the "Port Page 1 of 16

2 Mirroring Configuration" screen using the Console Interface (CI) Menus, which field should you select? A. <->Port X or Port Y <-> B. <->Port X and Port Y <-> C. ->Port X or Port Y -> D. ->Port X and Port Y -> Question: 4 An engineer configures a single instance of Virtual Router Redundancy Protocol (VRRP) across two Ethernet Routing Switch 8600s. One Ethernet Routing Switch 8600 is configured with a VRRP Priority of 255 and the other is configured with a VRRP Priority of 100. During testing the engineer notices that both Ethernet Routing Switch 8600s are in Master state. What is a possible cause for this? A. The Ethernet Routing Switch 8600 VRRP instances have been configured with the same VRID. B. A critical IP interface has not been configured for the Ethernet Routing Switch 8600 with a VRRP Priority of 100. C. VRRP has been configured on a VLAN on one 8600 and on a brouter port on the other D. The Ethernet Routing Switch 8600 VRRP instances have been configured with different VRIDs. Answer: D Question: 5 To monitor the performance of an Ethernet switched network, why would you use Enterprise Network Management System OmniView instead of Java Device Manager (JDM)? A. OmniView supports RMON while JDM does not. B. JDM is incapable of supporting the Business Policy Switch while OmniView supports it. C. OmniView can present statistics in both graphical and tabular formats while JDM only supports Tabular formats. D. JDM works with individual network components while OmniView works with subnets and LAN segments. Answer: D Question: 6 Which three statements are true regarding RMON alarms? (Choose three.) A. Alarms can only be viewed by Device Manager. B. Alarms have a corresponding rising and falling event. C. String variables can be used to define an alarm. D. Alarms have an interval polling period. E. All alarms define upper and lower threshold values., D, E Question: 7 Company.com would like to configure an IP address for an existing VLAN on an Ethernet Routing Switch Which Command Line Interface (CLI) commands correctly describe the process? Page 2 of 16

3 A. From the initial CLI prompt, enter config mode, enter config-if mode for the VLAN interface. Enter the command, "ip address" with the appropriate IP address and subnet mask in dotted decimal notation. B. From the initial CLI prompt, enter privilege mode, enter config mode, enter config-if mode for the VLAN interface. Enter the command, "ip address" with the appropriate IP address and subnet mask in dotted decimal notation. C. From the initial CLI prompt, enter privilege mode, enter config mode, enter the command, "ip address" with the appropriate IP address and subnet mask in dotted decimal notation. D. From the initial CLI prompt, enter privilege mode, enter config-if mode for the VLAN interface. Enter the command, "ip address" with the appropriate IP address and subnet mask in dotted decimal notation. Question: 8 An engineer needs to assign an IP address of to an Ethernet Routing Switch 8600 switch with a subnet mask of Which Command Line Interface (CLI) command should the engineer use? A. config bootconfig set ip /27 B. config bootconfig net mgmt ip /27 C. config bootconfig net mgmt ip /26 D. config bootconfig set ip /26 Question: 9 You are connecting a workstation with a Gigabit Ethernet Network Interface Card (NIC) that supports full-duplex mode to an Ethernet Routing Switch T on a 10/100/1000 Mbps port. You use a known functioning crossover cable to connect the workstation to the switch, but the port fails to come up and the workstation is unable to communicate with the switch. What is the most likely cause of this issue and which action should you take to resolve it? A. Auto MDI/MDIX has been disabled on the port. Enable Auto MDI/MDIX on the port. B. Autosensing does not function for Gigabit Ethernet connections. Configure the port as 1000 Mbs/full. C. Auto MDI/MDIX is not supported on Gigabit Ethernet connections. The issue cannot be resolved with a configuration change. D. Auto MDI/MDIX will not function if autonegotiation is disabled. Enable autonegotiation on the port. Answer: D Question: 10 An Ethernet Switch T-PWR is being configured to provide connectivity to a number of devices. The devices that may require Power over Ethernet (PoE) and their power requirements are shown below: Internet Camera: 5W each IP Phone: 10W each Wireless Access Point: 15W each Security Light: 25W each The Ethernet Switch T-PWR will be operating with only an internal power source, and the DC source has been configured as power sharing. Which represents a valid configuration? A. 10 IP Phones and 10 Wireless Access Points Page 3 of 16

4 B. 20 Internet Cameras and 5 IP Phones C. 12 IP Phones and 10 Internet Cameras D. 4 Security Lights and 10 Internet Cameras E. 4 Security Lights and 10 IP Phones Question: 11 Company.com has a stack of four Ethernet Switch Ts with a 1000 Mbps uplink configured in a Distributed MultiLink Trunk (DMLT) to an Ethernet Routing Switch 8600 at the network core. By adding a Business Policy Switch (BPS) to the stack and connecting the uplink to the BPS, what additional capability will this stack have? A. The ability to manage the entire stack with Ethernet Switching Element Manager. B. The ability to provide failsafe stacking for the entire stack for improved resiliency. C. The ability to manage the entire stack through a web interface. D. The ability to group the MLT in a Distributed MLT for improved redundancy. E. The ability to mark the Differentiated Services Code Point (DSCP) in packets going back to the core. Question: 12 If you do not know the IP address of an Ethernet Routing Switch 5510, what would you need to upload code to it? A. Java Device Manager B. Web browser C. Console Access D. Telnet Question: 13 What are three SMLT supported topologies? (Choose three.) A. triangle B. pentagon C. square D. linear E. full mesh, C, E Question: 14 Given the following information: An Ethernet Switch T-PWR is being installed. The switch will be fully populated with all devices requiring Power over Ethernet (PoE). The switch has been connected to both internal and external power sources. The switch will be configured through web-based management. Once you access the Ethernet Switch 460 via the BS460_24T_PWR(config)#poe poe-dc-source command, which configuration will provide the most power to supply PoE to the connected devices? A. nes - Set DC power source from NES Page 4 of 16

5 B. rpsu - Set DC power source from the rpsu C. unit - Set power pairs of another unit in a stack D. Ethernet 10 - Set DC power source from Ethernet 10 Question: 15 An engineer needs to be able to execute a command on a remote Ethernet Routing Switch Which command should the engineer use? A. mv B. rlogin C. rsh D. sio Question: 16 Which route type in the Ethernet Routing Switch 8600 routing table provides additional routes for faster convergence in case of network/link failures? A. best B. direct C. ECMP D. MPLS Question: 17 You are configuring an Ethernet Switch T for QoS and it is necessary to implement a meter as follows: Limit bandwidth utilization to 20 Mbps. Drop all traffic that exceeds the 20 Mbps threshold. How do you ensure that traffic that exceeds the 20 Mbps threshold is dropped? A. When adding the meter to the interface group, set Threshold-Exceeded-Traffic to Drop. B. When adding the meter to the policy, set Out-of-Profile Action to Drop_Traffic. C. When defining the Committed Burst Size of the meter, set Maximum Burst Size to 0 kbps and Duration to 0 seconds. D. When defining the Committed Burst Size of the meter, set Maximum Burst Size to 0 kbps. Question: 18 Given the following information: A Business Policy Switch and an Ethernet Switch T are connected with a 100 Mbps trunk. Due to the amount of traffic on this trunk and reports of slow response times, a second 100 Mbps trunk between the switches was added. The two trunks are grouped in a MultiLink Trunk (MLT). Even after this trunk addition, the users have continued to report slow response times. It has been verified that the physical connections are present and the LEDs for both trunks on each switch shows green. Using the Console Interface (CI) Menus, how can you determine if both MLTs are active and handling traffic? A. In the MLT Trunk Utilization screen, verify that both trunks are being utilized. B. In the Port Configuration screen, verify that both trunks are unabled C. In the MLT Trunk Configuration screen, verify that the Spanning Tree Protocol (STP) Learning field shows that all trunks are borwarding Page 5 of 16

6 D. In the Port Statistics screen, verify that the status of all trunks is unabled Question: 19 Given the conditions: Left LED - green Right LED - flashing green On an Ethernet Routing Switch 8648TXE/M 10/100 Ethernet I/O module, what is the status of a port that is displaying the LED conditions described above? A. Link speed is 10 Mbps and the port is passing traffic. B. Link speed is 100 Mbps and the port is passing traffic. C. Link speed is 10 Mbps and the port is disabled. D. Link speed is 100 Mbps and the port is disabled. Question: 20 Your customer is configuring the host-specific parameters of an Ethernet Routing Switch 8600 system, and wants to set the parameters for the information to be logged into the log file. Which command will allow parameters to be set for host 1? A. config/syslog/host/1 B. config sys syslog host 1 C. config/sys/syslog/host/1 D. config syslog host 1 Question: 21 You have installed a new Ethernet Switch T into Company.com's network and are using the QoS Wizard to configure the QoS settings for various IP traffic flows. Which two IP applications can you directly choose in the QoS Wizard to prioritize inbound frames based on traffic type? (Choose two.) A. Multicasting (IGMP) B. Trivial File Transfer (TFTP) C. File Transfer (FTP) D. (SMTP) E. Network Management (SNMP), D Question: 22 An engineer needs to free up space in an Ethernet Routing Switch 8600s flash memory prior to downloading a new version of software. Which Command Line Interface (CLI) command can be used to free up space by deleting a file which is no longer required? A. del /flash/p86a3060.img B. purge /flash/p86a3060.img C. rm /flash/p86a3060.img D. erase /flash/p86a3060.img Page 6 of 16

7 Question: 23 What is an advantage of using Independent VLAN Learning (IVL) mode over Shared VLAN Learning (SVL) mode on an Ethernet Switch T-PWR? A. Duplicate MAC addresses can be handled if they are in different VLANs. B. More MAC addresses can be stored with unique forwarding databases. C. The port forwarding rate will be greater with unique forwarding databases. D. The Spanning Tree Protocol (STP) can be disabled. Question: 24 A port is configured for 802.1q tagging and Spanning Tree Group 1 (STG 1). The default VLAN for this port is 5 while it is also configured for VLAN 3. Which statement about the Bridge Protocol Data Units (BPDUs) from STG 1 is true? A. The BPDUs will be tagged with 3. B. The BPDUs will be tagged with 1. C. The BPDUs will not be tagged. D. The BPDUs will be tagged with 5. Question: 25 Assume that Nortel devices are at both ends of a gigabit Ethernet fiber link. What is the condition under which the Single Fiber Fault Detection (SFFD) feature should be enabled for Ethernet Switch 470? A. When both ports making up the link are implemented using the Ethernet Switch 450 MDA. B. When at least one of the ports making up the link is implemented using the Ethernet Switch 450 Gigabit MDA. C. When both of the ports making up the link are implemented using the Ethernet Switch 470 Gigabit ports. D. When at least one of the ports making up the link is implemented using the Ethernet Switch 470 Gigabit port. Answer: D Question: 26 Which two statements are true regarding Virtual Router Redundancy Protocol (VRRP) Backup? (Choose two.) A. It must not accept packets addressed to the IP address(s) associated with the virtual router. B. It must discard packets with a destination Media Access Control (MAC) equal to the virtual router MAC. C. It must respond to Address Resolution Protocol (ARP) requests for address(s) associated with the virtual router. D. It must advertise its presence to the network., B Question: 27 Company.com has a network of Ethernet Switch Ts and Business Policy Switches. They Page 7 of 16

8 require a network management tool to discover and view all network nodes and their physical links on a topology map. Which network management tool provides this functionality? A. Enterprise Network Management System OmniView B. Enterprise Network Management System Autotopology Manager C. Java Device Manager (JDM) D. Enterprise Switch Manager Answer: D Question: 28 If one Multi Link Trunk is being used, how many fewer VLANs would be available on the Ethernet Routing Switch 8600? A. 4 B. 1 C. 8 D. 16 Question: 29 Which three switches support auto Media Dependent Interface Crossover (MDI/MDIX)? (Choose three.) A. Ethernet Switch 470 B. Ethernet Switch 425 C. Ethernet Switch 460 D. Ethernet Routing Switch 5510 E. Ethernet Switch 450, B, D Question: 30 You need to add a new port on an Ethernet Routing Switch 5510 that will support a new server to an existing VLAN that is a member of an existing Spanning Tree Group (STG). Which action(s) should you perform to accomplish this task? A. Add the port to the VLAN and then manually add the port to the STG. B. Disable the STG, add the port to the VLAN, and then enable the STG. C. Add the port to the VLAN. D. Remove the VLAN from the STG, add the port to the VLAN, and then add the VLAN to the STG. Question: 31 When can you obtain and load an image from an external TFTP server through one of the I/O ports? A. When you configure the Ethernet Routing Switch 8600 to boot from the network, then recycle power. B. When you invoke the boot (ip address):<file> command from the Command Line Interface (CLI). C. When you invoke the boot (ip address)/<file> command from the Device Manager. Page 8 of 16

9 D. When you configure the Ethernet Routing Switch 8600 to boot from the network, then reset. Question: 32 Company.com currently has an Ethernet Routing Switch 5510 deployed on a network, with multiple VLAN IP interfaces. They want to allow hosts on one VLAN to access hosts on other VLANs. Which statement is true? A. Each VLAN must be on a separate STP group. B. IP forwarding must be enabled. C. Hosts on different VLANs will not be able to access each other. D. DHCP relay must be enabled. Question: 33 Your customer wishes to prevent any IP traffic from being routed to a specific port on their VLAN. What should you do to accomplish this request? A. Remove the port from the neighboring VLAN routing tables. B. Disable routing on the port in question. C. Mask the port in the routing table. D. Disable RIP on the VLAN segment. Question: 34 A new network of Ethernet Switch Ts is being deployed. When defining an IEEE 802.1Q VLAN group of ports (workgroup) using one of the switch interfaces, why would you define a port as tagged? A. To allow multiple VLANs without the need to use multiple physical links. B. To allow the Spanning Tree Protocol (STP) to be disabled if multiple links are defined. C. To allow the port to be added to a MultiLink Trunk (MLT) group. D. To allow servers to connect to a switch that is a member of multiple VLANs. Question: 35 Given the following information: Three PCs (PC1, PC2, and PC3) are connected to an Ethernet Routing Switch All are members of the same VLAN and are in the same IP subnet. PC1 and PC2 have joined Multicast Group A while PC3 has not. You have noticed that the IP Multicast stream for Multicast Group A is being sent to PC3 despite the fact that it has not joined the group. Which feature should you enable on the Ethernet Routing 5510 to resolve this issue? A. IGMP Group Membership Query B. IGMP Host Membership Query C. IGMP Snooping D. IGMP Proxy Reports Question: 36 Page 9 of 16

10 Which two statements describe how the Multi-Link Trunking (MLT) algorithm on the Ethernet Routing Switch 8600 determines the correct link to use for forwarding a packet? (Choose two.) A. Both the source and destination MAC are used at Layer 2. B. Only the destination Media Access Control (MAC) is used at Layer 2. C. Only the source IP is used at Layer 3. D. Only the destination IP is used at Layer 3. E. Both the source and destination IP are used at Layer 3. F. Only the source (MAC) is used at Layer 2., E Question: 37 In the event of a network failure, Company.com requires that an Open Shortest Path First (OSPF) interface detect the failure within 30 seconds. Which Ethernet Routing Switch 8600 Command Line Interface (CLI) command must be used to ensure a network failure is detected in the required amount of time? A. config vlan <vid> ip ospf hello-interval 30 B. config vlan <vid> ip ospf dead-interval 30 C. config vlan <vid> ip ospf priority 30 D. config vlan <vid> ip ospf metric 30 Question: 38 Company.com with an Ethernet Switch T wants to configure MAC address-based security. Given that they can create up to 10 MAC Destination Addresses (DA) to filter, how are all packets with specified DAs treated? A. All packets with specified DAs are dropped. B. All packets with specified DAs are dropped based on source address intrusion. C. All packets with specified DAs are dropped based on ingress port. D. All packets with specified DAs are dropped based on VLAN membership. Question: 39 How many levels of priority can be defined in the tagged portion of an 802.1Q tagged frame? A. 8 B. 2 C. 4 D. 16 E. 32 Question: 40 You want to remotely manage an Ethernet Switch 450. Which two management options are available to do this? (Choose two.) A. Web interface B. Telnet C. Console Page 10 of 16

11 D. JDM, D Question: 41 Your customer has a new software image that they want to use. What is used to transfer a new software image to an Ethernet Routing Switch 5510? A. TFTP B. FTP C. Xmodem D. BootP Question: 42 Click the exhibit button. Given the following Ethernet Switch T configuration: VLAN 10 is a port-based VLAN. Port 1 is an untagged member of VLAN 10. Port 5 is a tagged member of VLAN 10. The device on Port 1 transmits an untagged frame to the device on Port 5. How will an untagged frame be treated when it reaches Port 5 on this switch? A. It will be placed in a hardware-based queue based on Priority 2. Then it will be tagged, and transmitted out Port 5 with Priority 2. Page 11 of 16

12 B. It will be discarded when it is received. C. It will be placed in a hardware-based queue based on Priority 6. Then it will be tagged, and transmitted out Port 5 with Priority 2. D. It will be placed in a hardware-based queue based on Priority 6. Then it will be tagged, and transmitted out Port 5 with Priority 6. Answer: D Question: 43 What is the maximum number of ports that can be mirrored on an Ethernet Routing Switch 8600 at any one time? A. 256 B. 192 C. 383 D. 512 Question: 44 An engineer needs to monitor an Ethernet Routing Switch 8600 for RMON events. How many RMON groups does Ethernet Routing Switch 8600 support? A. 4 B. 11 C. 9 D. 7 Question: 45 Which Ethernet Routing Switch QoS feature ensures that the lower six egress queues are serviced in a fair, yet weighted manner? A. TCP/UDP B. WRR C. DSCP D. WFQ Question: 46 Given the following information: An Ethernet Switch T-PWR is being configured for QoS. An interface group has been created with all the necessary ports assigned to it, and a filter will be associated with this interface group. The requirements are to update the Differentiated Services Code Point (DSCP), IEEE802.1p and Drop Precedence for incoming packets. Which configuration should be used to enable the marking of the DSCP, IEEE802.1p and Drop Precedence? A. Interface Class: Trusted Type of Filter: IP Filter B. Interface Class: Trusted Type of Filter: Layer 2 Filter matching IP traffic C. Interface Class: Unrestricted Type of Filter: Layer 2 Filter for non-ip traffic Page 12 of 16

13 D. Interface Class: Untrusted Type of Filter: IP Filter Answer: D Question: 47 An untagged frame enters a port on the Ethernet Routing Switch The port is a member of four different types of VLANs (port-based, IP subnet, MAC, and protocol). Assuming the frame matches the criteria for each of the defined VLANs, which VLAN will the frame become a member of upon ingress? A. Port B. MAC C. Protocol D. IP Subnet Question: 48 Your customer is initially configuring an Ethernet Switch T-PWR to connect Internet Telephones. The management tasks will be performed on different subnets. Which two parameters must first be set to allow the switch to be accessed remotely for management purposes? (Choose two.) A. management VLAN B. default gateway C. SNMP Read-Only and Read-Write community strings D. BootP request mode E. IP address/subnet mask, E Question: 49 Given the following information: Company.com has an Ethernet Switch T stack that is connected to a file server via two 100 Mbps connections that are arranged in a MultiLink Trunk (MLT). They want to increase the throughput and redundancy provided in this connection from the file server to the Ethernet Switch T stack. Given that the customer has additional slots in their server, which configuration change should you make to this connection to meet their needs? A. four 100 Mbps connections defined in a SMLT B. six 100 Mbps connections defined in a SMLT C. four 100 Mbps connections defined in a DMLT D. four 100 Mbps connections defined in an MLT E. six 100 Mbps connections defined in a DMLT Question: 50 Company.com is managing an Ethernet Switch 450 using Java Device Manager. They are currently using the default VLAN configuration. They would like to separate groups of users into different broadcast domains. Which statement is true? A. You must configure two additional VLANs by accessing the VLAN menu and then select VLANs. You then insert two VLANs onto the 450 and specify appropriate ports for each VLAN. Page 13 of 16

14 B. You must configure one additional VLAN by accessing the VLAN menu and then select VLANs. You then insert another VLAN onto the 450 and specify appropriate ports. C. You must configure three additional VLANs, one for management, and then two others for the Different users by accessing the VLAN menu and then select VLANs. You then insert the three VLANs onto the 450 and specify appropriate ports. D. The 450 default configuration already specifies two separate broadcast domains. Question: 51 If a tagged data frame is seen on an access port, what will happen to the frame? A. It is placed in VID=1 if the DiscardTaggedFrames on tagged ports is set to discard. B. It is placed in VID=1 if the DiscardTaggedFrames on access ports is set to true. C. It is placed in VID=1 if the DiscardTaggedFrames on access ports is set to false. D. It is placed in VID=1 if the DiscardTaggedFrames on tagged ports is set to keep. Question: 52 An Ethernet Switch T will be added to an existing stack of two Ethernet Switch Ts. The software Release running on the Ethernet Switch T is compatible with the software Release running on the Ethernet Switch Ts. To complete the stack creation successfully, which two configuration changes are necessary? (Choose two.) A. Set the Stack Mode for the Base Ethernet Switch T to Hybrid and leave the other Ethernet Switch T as Pure. B. Set the Unit Select switch on the Ethernet Switch T to "Base" ("On" position). C. Set the Stack Mode for all Ethernet Switch Ts to Hybrid and then reset the stack. D. Cable the Ethernet Switch T into the stack, power off all units, and then power up the stack. E. Set the Unit Select switch on the Ethernet Switch T to the "Off" position., E Question: 53 You have specified a trap receiver to be used for Web-based management under Configuration SNMP Trap Receiver. Which type of SNMP traps can be sent to the trap destination? A. SNMP v1 B. SNMP v1 and v3 C. SNMP v1, v2 and v3 D. SNMP v3 Question: 54 You have just installed a new Ethernet Switch T into an existing medium-sized Enterprise network. Which QoS setting can you initially configure on this switch using the QoS Wizard? A. Prioritize a VLAN to receive better service than others. B. Schedule the time frame in which a policy is active. C. Modify the Differentiated Services Code Point (DSCP) to queue set mappings. D. Modify the 802.1p priority to Differentiated Services Code Point (DSCP) mappings. Page 14 of 16

15 Question: 55 When an engineer gathers RMON history to troubleshoot alarms, it is gathered in time intervals. What are those time intervals called? A. buckets B. community strings C. time traps D. over-sampling Question: 56 Which statement is true when RADIUS is implemented? A. If no server answers, the switch itself must reject authentication attempts. B. If a server rejects authentication, no local authentication is made on the switch. C. If a server rejects authentication, local authentication by the switch itself can authenticate a user. D. Authentication (console/telnet) is completed first on the switch. Question: 57 How do you change an IP address on the Ethernet Routing Switch 8600? A. use the VLAN Manager B. reset the switch, then configure the address again C. run the ipchange command from the Command Line Interface (CLI) D. delete and recreate the IP address Answer: D Question: 58 You are configuring QoS on an Ethernet Switch T using the Web-based Management System Interface. How are these multiple hardware-based queues used for each port on this switch? A. Frames are inspected at the ingress and placed in different priority egress queues depending on the IEEE 802.1p user priority. B. Frames are inspected at the egress and placed in different priority ingress queues depending on the IEEE 802.1p user priority. C. Frames are inspected at the egress and placed in different priority ingress queues depending on the Differentiated Services Code Point (DSCP)s. D. Frames are inspected at the ingress and stored in the egress queues allowing the switch to mark the Differentiated Services Code Point (DSCP)s. Question: 59 A network design engineer is configuring Company.com's network. The customer has a number of Internetwork Packet Exchange (IPX) clients on the network that attempt to login to a server immediately after boot up. If a port on the Ethernet Routing Switch 8600 does not begin forwarding packets from these clients almost immediately after link is detected, the login will Page 15 of 16

16 timeout and be unsuccessful. What feature should be enabled on the Ethernet Routing Switch 8600 ports with the customer's IPX clients connected? A. Quality of Service B. Autonegotiation C. Spanning Tree FastStart D. VLAN tagging Question: 60 Which actions should be performed during a configuration of a QoS policy for a trusted interface? A. modification of 802.1p value B. drop traffic to a port C. change of DSCP value D. alteration of the drop precedence Question: 61 An engineer wants to configure the Virtual Router Redundancy Protocol (VRRP) priority for an IP interface on a Port-based VLAN. Which 8600 Command Line Interface (CLI) command should be used? A. config ip vrrp <vrid> priority <prio> B. config vlan <vid> ip vrrp <vrid> priority <prio> C. config ethernet <port> ip vrrp <vrid> priority <prio> D. config ethernet <vid> ip vrrp <vrid> priority <prio> Page 16 of 16