1) By installing this product onto your vehicle, you assume all risk and liability associated with its use.

Transcription

1 FUEL TANK SUMP KIT

2 ! DISCLAIMER ) By installing this product onto your vehicle, you assume all risk and liability associated with its use. 2) It is your responsibility to make sure your vehicle complies with all federal, state, and local emissions laws. Federal and many state and local laws prohibit the removal, modification or rendering inoperative of any part of the design affecting emissions or safety on motor vehicles used on a public street or highway. Violation may result in a fine of up to $32,500 per vehicle (or possibly higher depending on changes in the law). All civil penalties and fines for removing your vehicle s emissions equipment are the sole responsibility of the end user. 3) Due to its high performance nature, this product may void vehicle manufacturer s warranty. 4) Sinister Mfg Company, Inc. is not responsible for misuse of its products. By installing this product, you release Sinister Mfg Company, Inc. of any and all liability associated with its use. 5) Depending on where you live, restrictions may apply. Check all applicable laws before installing or using! 6) The purchaser and end user releases, indemnifies, discharges and holds harmless Sinister Mfg Company, Inc. from any and all claims, damages, causes of action, injuries, or expenses resulting from or relating to the use or installation of this product that is in violation of the terms and conditions on this page, the product disclaimer, and/or the product installation instructions. Sinister Mfg Company, Inc. will not be liable for any direct, indirect, consequential, exemplary, punitive, statutory, or incidental damages or fines caused by the use or installation of this product.

3 A Fuel Tank Sump Kit B C D E F G H Part# A B C D E F G H I PACKING LIST: QTY. 0 0 I The teflon tape Description should be wrapped Threaded mounting ring clock-wise when Nitrile Buna Gasket looking at the fitting Blue anodized sump cap Teflon tape from this angle. /2 NPT hose barb /4-20 Stainless steel socket head cap screw /4 Neoprene washers Silicone Locktite Read all instructions prior to install. Note: Prior to installation, please compare the parts that you have received with the bill of materials provided on this page to assure that you have all the parts necessary for the installation. 2

4 ! CAUTION!!! Never work on a hot vehicle. Serious injury in the form of burns can result if the vehicle has been in use. Allow vehicle to cool prior to installation. Always wear eye protection when working on or under any vehicle. Note: Not recommended for any vehicle with clearance issues. Important to know that this product is to be used in conjunction with an aftermarket lift pump. Installation of this product requires the factory fuel tank to be cut; when cutting or drillilng any fuel tank be very cautious Step : Completely drain fuel tank. (For safest and cleanest install make sure fuel tank is empty.) Step 2: Determine location for Fuel Tank Sump. We suggest installing the sump on the flatest surface near the center of the tank. Image 2.5 x.6376 Image Step 3: After locating the optimal location for sump, mark the center and drill a small pilot hole. (This hole will allow any remaining fuel to drain and serve as a locator for your hole saw.) (Image ) Step 4: You are now ready to cut the three inch hole using a three inch hole saw and the previously drilled pilot hole. (Image 2) Image 2 Step 5: Determine which direction the /2 NPT hose fitting needs to face for your fuel system and test fit the blue anodized sump cap. 3 Image 3

5 Step 6: Once the orientation is determined mark all bolt holes and remove the sump cap and drill bolt holes using a 7/64 drill bit (slighty larger than /4 ). (Image 3) Step 7: Deburr all edges and remove any residual shavings and fragments from cutting and drilling. Step 8: Manuever threaded mounting ring through the three inch hole and line up with the holes drilled in step six. (Image 4) Image 4 Step 9: Install /2 NPT hose barb with teflon tape applied. Step 0: Test fit the sump cap to confirm that all holes line up (may be helpful to start two of the provided bolts). (Image 5) Note: Clean the mounting area of the tank so that it is free of any oils or dirt. Image 5 Step : Apply a thin layer of silicone to both sides of gasket and position it on the flange of the sump cap. Step 2: Using locktite and neoprene washers install all (0) bolts and tighten evenly (use caution to not over tighten as this will cause damage to the gasket). (Image 6) Image 6 Step 3: Install fuel line to /2 NPT barbed hose fitting. This is meant to be a press on fit, if for any reason the hose is loose or leaking a hose clamp can be used. (Image 7) Step 4: Allow adequate time for silicone to cure prior to filling tank. 4 Image 7

6 FEATURED PRODUCTS CUMMINS DURAMAX POWERSTROKE Upgraded EGR Coolers Coolant and Oil Filtration EGR Delete Kits Intake Tubes Leveling Kits Fuel Rail Race Valve 5

7 AR Exhaust Tip Dodge Steering Stabilizers 6.0L Powerstroke Headers 6.0L Powerstroke Y-Pipe 6

8 2025 Opportunity Dr. Suite #7 Roseville CA, SinisterDiesel.com