HDMI CAT5e/6 Extender with IR - 50m

Transcription

1 HDMI CAT5e/6 Extender with IR - 50m P/N: HDMIExt G4-0013A

2 Congratulations for owning a gofanco product. Our products aim to meet all your connectivity needs wherever you go. Have fun with our products! Please read this manual carefully before first use. If you need more information about our products, please visit For technical support, please us at support@gofanco. com. For drivers/manuals download, please go to www. gofanco.com/download. 2

3 Introduction gofanco HDMI CAT5e/6 Extender with IR - 50m (part# HDMI Ext) extends HDMI signals over one Cat5e/6 cable up to 50m (164ft) with an HDMI loop out on the Transmitter (TX) for a local monitor or cascading. Specifications Output Signal Resolution Audio Transmission Distance Network Cable HDMI Cable Power Supply HDMI Up to 1080p Up to 7.1 ch Up to 50m (164ft) CAT5e/6 Up to 5m (Input & Output) DC 5V/1A Package Contents HDMI CAT5e/6 Extender with IR - 50m (TX & RX) 1x Power adapter IR Blaster extension cable & IR Receiver extension cable User's guide 3

4 Layout HDMI In HDMI Out EDID Figure 1: Transmitter (TX) - HDMI Device Input HDMI In: Connect your HDMI source here with an HDMI cable (cable not included) EDID: EDID learning switch. (Right position: Learn EDID from the display connected to HDMI loop out; Left position: Learn EDID from the display connected to Receiver (RX)) HDMI Out (optional): Connect to a local HDMI display here or for cascading HDMI signals Power LED Signal LED IR Out RJ45 Power Jack Figure 2: Transmitter (TX) - RJ45 Output 4

5 IR Out: Infrared 3.5mm socket. Plug IR Blaster extension cable here RJ45: Link to the Receiver's RJ45 via a Cat5e/6 cable Power Jack: Connect the included 5V DC power adapter here Power LED: On when the Transmitter is powered Signal LED: On when the signal is detected Power LED Signal LED IR In RJ45 Figure 3: Receiver (RX) - RJ45 Input IR In: Infrared 3.5mm socket. Plug IR Receiver extension cable here RJ45: Link to the Transmitter's RJ45 via a Cat5e/6 cable Power LED: On when the Receiver is powered. (It will be powered when connected to the TX via Network cable.) Signal LED: On when the signal is detected 5

6 Equalizer control HDMI Out Figure 4: Receiver (RX) - HDMI Display Output Equalizer control: Adjust the 8-level equalization control to the received HDMI signals (0~7: weakest to strongest) HDMI Out: Connect to your HDMI display here with an HDMI cable (cable not included) 6

7 IR Extenders (30KHz - 60KHz) Figure 5: IR Blaster (Connect to Transmitter TX) Figure 6: IR Receiver (Connect to Receiver RX) IR Blaster: Plug into the Transmitter's IR 3.5 socket to emit IR signals received from the IR Receiver end. IR Receiver: Plug into the Receiver's IR 3.5 socket to receive IR signals from a remote control for the HDMI device connected to the Transmitter. Note: Incorrect placement of the IR Blaster and IR Receiver may result in failure of these cables. Please check carefully before plugging in the IR cables to proper IR sockets. 7

8 Hardware Installation 1. Power off all devices including your HDMI source and display(s). 2. Connect your HDMI source to the Transmitter's HDMI IN connector. 3. Optional: Connect the IR Blaster extension cable to the Transmitter's IR Out. Face the eye towards your HDMI device's IR window. 4. Optional: Connect your HDMI display to the Transmitter's HDMI OUT. It's only needed when used with a local monitor or to cascade HDMI output signals. 5. Connect your HDMI display to the Receiver's HDMI OUT connector with an HDMI cable (cable not included). 6. Optional: Connect the IR Receiver extension cable to the Receiver's IR In. 7. Connect and link the Transmitter and Receiver by a CAT5e/6 cable. 8. Plug the included power adapter into the Transmitter's Power Jack, then plug the power adapter into a reliable power outlet. (Power will pass through to the RX by PoC) 9. Power on your HDMI device and HDMI display(s). 10. If a flickering or blinking image is seen, adjust the Receiver's Equalizer control to improve the image quality. 8

9 Application Extend HDMI signals from DVD players, game consoles or HDMI-equipped computers up to 50m (164ft). Receiver Transmitter HDMI Monitor-2 HDMI Source Figure 7: Application HDMI Monitor-1 (Optional) * When using the remote control, please make sure its distance to the IR Receiver extension cable is within 5 meters and without obstructions. 9

10 10 Blank Page

11 Blank Page 11

12 Thank you for choosing gofanco