Checklist for Insertion and Setup of an ICP Monitoring Device

Transcription

1 Checklist for Insertion and Setup of an ICP Monitoring Device Before proceeding, contact neurosurgery to identify the type of catheter to be inserted. The catheter type will define the equipment requirements and preparation needed. 1. Obtain the Catheter (choose one of 3 types below): A. Codman Microsensors (two types): Codman Microsensors are catheters that measure intracranial pressure via a strain guage microchip located at the tip of the catheter. Both Microsensor catheters below are connected to the Codman Express for pressure monitoring. Unlike fluid filled pressure monitoring, pressure transmission is unaffected by obstructed fluid paths (e.g., from clot or tissue). I. Codman Microsensor Intraparenchymal Catheter: This catheter is inserted into superficial brain tissue. It measures pressure only, it does not drain CSF. It may be used for monitoring when ventricles are too small to access, or in patients with normal intracranial pressure who are at risk to develop elevated pressures. If ICP rises, it may be changed to an EVD. II. Codman Microsensor Intraventricular Drainage Catheter: This is an intraventicular catheter. It is used to measure ICP and to drain CSF. 1

2 B. Standard Intraventricular Drainage Catheter: The standard ventricular catheter is used to measure ICP and to drain CSF. Pressure is measured using a standard tranducer, picking up pressure that is transmitted through the fluid filled channel of the catheter. 2. Obtain supplies to insert ICP Catheter: Ventricular Drainage Tray (ensure drill is packaged with tray) Hair clipper with clipper head Line cart Sterile gowns Large sterile drape and sterile towels Local anaesthetic Tegaderm dressing 3. Do you need a CSF drainage unit (Codman EDS 3)? Both the Codman Microsensor venticular drainage catheter and the standard ventricular drainage catheter require a CSF drainage unit. There is no drainage of CSF with an intraparenchymal catheter. Supplies Needed: Codman EDS 3 Standard pressure transducer kit (used to flush drainage unit) 500 ml bag of normal saline Codman laser level Portable IV pole 2

3 4. Obtain supplies for pressure monitoring: Microsensor catheters (intraparenchymal or intraventricular): Codman Express monitor Codman Express cable (should be attached to Codman Express ) Codman -Datex pressure cable for transferring pressure from the Codman Express to the Datex monitor (Datex end of cable is red) Datex pressure module (e.g., P3, P4 or an unused P2) Standard Intraventricular Drainage Catheter: Datex pressure module (e.g., P3, P4 or an unused P2) Datex regular pressure cable Pressure transducer (also used to prime Codman EDS3 drainage unit) PROCEDURE FOR PRIMING CODMAN EDS3 (CSF collection unit): For Codman Microsensor ventricular drainage catheter and standard ventricular drainage catheter. Perform hand hygiene Hang the Codman EDS3 on IV pole Prime pressure tubing with normal saline (do not pressurize saline bag) Connect pressure tubing to the Codman EDS3 stopcock that is closest to the patient catheter Flush drainage tubing toward patient catheter connection, then into CSF collection chamber Turn patient stopcock to 45 degrees (off in all directions) until ready to hook up Using laser level, adjust position of drainage unit until 0 on drainage panel is level with external auditory canal Position the drip chamber to the ordered level (be sure the orders clearly identify whether the order is for cmh20 or mmhg 3

4 4

5 PROCEDURE FOR SETUP UP OF CODMAN EXPRESS For both Codman Microsensor Catheters Perform hand hygiene Place Codman Express on IV pole and plug into red electrical outlet Turn Codman Express on and listen for audio beep Assist physician to prepare sterile field and open Codman Microsensor catheter 5

6 Connect Microsensor to Codman Express cable As soon as cable is connected, Transducer Detected will appear on the screen Provide physician with a syringe of sterile saline. This will be used to fill the catheter tray and submerge the tip of the catheter during zeroing. With catheter in the horizontal position and submerged in 3 inches of sterile saline, press the Zero button when prompted 6

7 When zeroing is completed, a 3 digit reference number will display Document the 3 digit reference number in the Kardex and AI record. Record the number on the Microsensor with a Sharpie Press Menu/Enter Catheter can now be inserted; the pressure will automatically display on the Codman Express PROCEDURE FOR CONNECTING CODMAN EXPRESS TO DATEX MONITOR For both Codman Microsensor Catheters ICP is measured by the Codman Express. This pressure can be duplicated on the Datex monitor for the purpose of generating an ICP waveform. Perform hand hygiene Connect the Codman -Datex cable to the back of the Codman Express and to any spare pressure module (e.g., P3, P4 or an unused P2) 7

8 Go to Invasive Pressures (Datex ) and change the module label to ICP When prompted (on the Codman Express screen), press the Zero button on the Datex module. (Note that you do not need to open any stopcocks or adjust the position of any tubing or devices). Confirm that the reference line for the ICP waveform is displaying zero 8

9 When prompted (on the Codman Express screen), confirm that the monitor is reading zero by selecting the menu/enter button When prompted to choose the calibration signal, select the 20 button Confirm that the bedside monitor has a reference line at 20 mmhg 9

10 Press the menu/enter button to verify that the bedside monitor is correct; if it is not, use the arrow keys to adjust the reference line PROCEDURE FOR MONITORING ICP WITH STANDARD VENTRICULAR CATHETER: ICP is measured with standard transducer and fluid filled circuit. Perform hand hygiene After priming the Codman EDS3, connect the pressure transducer cable to a bedside Datex module (e.g., P3, P4 or a spare P2) Change the Module label to ICP Tape the transducer to the back of the Codman EDS3 aligning the stopcock from the transducer with the zero reference stopcock on the Codman EDS3. Confirm that the stopcocks are level with the patient s external auditory canal using a laser level Zero the transducer Please note the following: An LCD switch is located on the back of the ICP Express to see screen in the dark Alarms are automatically off when ICP express is turned on. To activate alarms go to menu/enter button, choose on/off alarm limits option and activate alarm option by arrowing up or down for required limits. Troubleshooting When zeroing the ICP Express monitor, if the value -99 appears this means the grey cable that connects to the front of the ICP Express monitor needs to be replaced If a zero reference number appears before zeroing, turn ICP Express off and restart steps Traveling Disconnect catheter from grey cable attached to ICP Express When reconnecting catheter to ICP Express, the reference number on the monitor must match the number written on the catheter. Either accept the displayed reference number (if they match) or adjust. Go to menu/enter and use arrow key to choose the correct reference number The Codman Microsensor is MRI compatible Judy Hackett RN BScN CNCC(c) Clinical Educator, CCTC June 12, Revised April 7, 2010 (BM); Revised May 28, 2010 (BM) 10