Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version

Transcription

1 Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 August 27, 2012 Windows XP Release Notes

2 TABLE OF CONTENTS 1 Introduction to Release Notes... 1 Structure of the Document... 1 Changes in this Edition Changes in the Release 304 Driver for Windows XP... 2 Version Highlights... 3 Existing Support... 3 What s New in Release What s New in Version Limitations in this Release... 4 Discontinued Features in this Release... 4 Advanced Instructions for This Release... 5 Turning Off V-Sync to Boost Performance... 5 NVIDIA Application Configuration Engine (ACE)... 5 NVIDIA Multi-OS GPU Assignment in System Virtualization... 6 Changes in Version Open Windows XP Issues in Version NVIDIA Recommendations... 2 Windows XP 32-bit Issues... 2 Windows XP 64-bit Issues... 3 Not NVIDIA Issues... 4 Known Product Limitations... 6 System Should not Enter Sleep/Hibernate Mode With SDI Capture in Progress... 7 SDI Capture Driver Must be Installed Separately... 7 Driver May not Work with /3GB Windows Switch When Using ECC on 32-bit OS... 7 Professional 3D Stereo Left-Right Buffer Swap... 8 Using HDMI/DisplayPort Audio with Displays that have a High Native Resolution... 8 Using HDMI/DisplayPort Displays that do not Support Audio... 9 Using HDMI/DisplayPort Audio in Dualview or Clone Mode Configurations10 GPU Runs at a High Performance Level (full clock speeds) in Multi-display Modes Hz not Available on BenQ FP241W Monitors Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 i

3 TABLE OF CONTENTS Image Sharpening Control not Available with Quadro FX 4600 and Later GPUs More Monitors are Listed in the Windows Device Manager than are Actually Connected PowerDVD 5.0 Does Not Display Correctly in nview Span Mode DirectX Fails When Detaching/Reattaching Displays in Dualview Mode 11 OpenGL Viewport Scaling Problem in Horizontal Span Mode Video Playback in nview Clone and Span Modes Monitor Ordering in the Windows Settings Page No Antialiasing of 3DMark03 Image Quality Screen Captures Windows XP/2000 Issue with Settings Tab Monitor Positioning Antialiasing Problems With Certain Applications Poor Quality S-Video Output on Some TVs AGP and PCI-E Programs May Hang With AMD K7 and K8 Processors Desktop Manager Does Not Re-Center Logon Screen The Release 304 Driver for Windows XP...18 Hardware and Software Support Supported Operating Systems Supported NVIDIA Products Supported Languages Driver Installation System Requirements Installation Instructions Appendix A: Mode Support for Windows...28 General Mode Support Information Default Modes Supported by GPU for Windows XP Understanding the Mode Format NVIDIA Quadro & NVS GPUs Modes Supported by TV Encoders Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 ii

4 01 INTRODUCTION TO RELEASE NOTES This edition of Release Notes describes the Release 304 family of Tesla, Quadro, & NVS Professional Drivers for Microsoft Windows XP. NVIDIA provides these notes to describe performance improvements and bug fixes in each documented version of the driver. Structure of the Document This document is organized in the following sections: Changes in the Release 304 Driver for Windows XP on page 2 gives a summary of changes, and fixed and open issues in this version. The Release 304 Driver for Windows XP on page 18 describes the NVIDIA products and languages supported by this driver, the system requirements, and how to install the driver. Mode Support for Windows on page 28 lists the default resolutions supported by the driver. Changes in this Edition This edition of the Release Notes for Windows XP includes information about NVIDIA graphics driver version , and lists changes made to the driver since version These changes are discussed beginning with the chapter Changes in the Release 304 Driver for Windows XP on page 2. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 1

5 02 CHANGES IN THE RELEASE 304 DRIVER FOR WINDOWS XP This chapter describes open issues for version , and resolved issues and driver enhancements for versions of the Release 304 driver up to version The chapter contains these sections: Version Highlights on page 3 Advanced Instructions for This Release on page 5 Changes in Version on page 1 Open Windows XP Issues in Version on page 2 Not NVIDIA Issues on page 4 Known Product Limitations on page 6 Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 2

6 Chapter 02 : CHANGES IN THE RELEASE 304 DRIVER FOR WINDOWS XP Version Highlights This section provides highlights of version of the NVIDIA Release 304 Driver. Existing Support What s New in Release 304 What s New in Version Limitations in this Release Discontinued Features in this Release Existing Support This release supports the following APIs: Open Computing Language (OpenCL) 1.0 in Quadro FX Series x700 and newer as well as the FX4600 and FX5600. OpenGL 4.2 DirectX 11 CUDA 5.0 What s New in Release 304 The section summarizes the following driver changes in Release 304: ODE Driver The R304 drivers are the second 'Optimal Drivers for Enterprise', a release dedicated to relatively long term stability for ISV certification, OEMs, and Enterprise customers. Workstation Developer APIs and Support CUDA 5.0 Added support for CUDA 5.0, which is available as a Preview Release for registered developers. For more information, visit What s New in Version This driver offers performance improvements over previous driver versions, including workstation compatibility fixes. See Changes in Version on page 1 for a list of resolved issues in this driver version. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 3

7 Chapter 02 : CHANGES IN THE RELEASE 304 DRIVER FOR WINDOWS XP Limitations in this Release Video Memory Support For Windows XP 64-bit, this driver recognizes up to the total available video memory on Quadro cards for Direct3D and OpenGL applications. For Windows XP 32-bit, this driver recognizes only up to 4 GB of video memory on Quadro cards for DirectX, OpenGL, and CUDA applications. Discontinued Features in this Release NVIDIA AutoCAD Performance driver is no longer integrated in the graphics driver. Standalone versions or version updates can still be downloaded from the NVIDIA driver download page. Removed the following from the NVIDIA Control Panel: Views option You no longer need to select between Standard and Advanced views for many NVIDIA Control Panel controls. Profiles menu. The following products are no longer supported: NVIDIA Quadro FX 4400 NVIDIA Quadro FX 3400 Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 4

8 Chapter 02 : CHANGES IN THE RELEASE 304 DRIVER FOR WINDOWS XP Advanced Instructions for This Release This section clarifies instructions for successfully accomplishing the following tasks: Turning Off V-Sync to Boost Performance To get the best benchmark and application performance measurements, turn V-Sync off as follows: 1 Open the NVIDIA Control Panel and make sure that Advanced Settings is selected from the control panel tool bar. 2 From the Select a Task pane, under 3D Settings, click Manage 3D Settings, then click the Global Settings tab. 3 From the Global presets pull-down menu, select Base profile. 4 From the Settings list box, select Vertical sync and change its value to Force off, then click Apply. 5 From the Global presets pull-down menu, select 3D App - Default Global Settings (the driver s default profile) or use the application profile that matches the application you are testing, then click Apply. Be sure to close the NVIDIA Control Panel completely leaving it open will affect benchmark and application performance. NVIDIA Application Configuration Engine (ACE) This driver includes the NVIDIA Application Configuration Engine (ACE), which automatically detects the workstation application and configures the appropriate profile settings in the NVIDIA Control Panel. See the NVIDIA Quadro Professional Drivers: NVIDIA Control Panel Quick Start Guide for more information about this feature. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 5

9 Chapter 02 : CHANGES IN THE RELEASE 304 DRIVER FOR WINDOWS XP NVIDIA Multi-OS GPU Assignment in System Virtualization On systems with two supported graphics cards installed, this driver supports a system virtualization tool s ability to directly assign a GPU to a guest virtual machine (VM). This direct assignment allows the host and guest VM to each run on their own operating system and with their own GPU and driver. Supported Virtualization Software: Parallels Workstation Extreme and Citrix XenServer 6 Supported Graphics Cards Up to two different models can be used in a system, from among the following: Quadro 6000 Quadro 5000 Quadro 4000 Quadro 2000 Quadro FX 5800 Quadro FX 4800 Quadro FX 3800 Video BIOS Requirement The graphics card assigned to the guest VM needs video BIOS version or later. For a list of NVIDIA Multi-OS certified workstations, virtualization software, and OS combinations, please see Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 6

10 Changes in Version Changes in Version The following sections list the important changes and the most common issues resolved since driver version Quadro 6000: Cinebench the application is slower when using vertex array objects. Quadro 2000/4000/5000: Data errors occur when loading the LUT. Quadro 6000: Catia/RTT blue-screen crash occurs when running the application with stereoscopic 3D is enabled. Quadro 6000: Mantis buffer swap problems occur when running the application in full-screen mode. Quadro 6000: Quantum3D glitches occur when a new model or object is drawn. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 1

11 Open Windows XP Issues in Version Open Windows XP Issues in Version As with every released driver, version has open issues and enhancement requests associated with it. This section includes lists of issues that are either not fixed or not implemented in this version. Some problems listed may not have been thoroughly investigated and, in fact, may not be NVIDIA issues. Others may have workaround solutions. NVIDIA Recommendations on page 2 Windows XP 32-bit Issues on page 2 Windows XP 64-bit Issues on page 3 NVIDIA Recommendations Single display modes such as TV-only, DFP/LCD-only, or CRT-only provide the best performance and quality from Windows Media Center Edition. Dual display modes such as Dualview and nview Clone and Span modes are not recommended when using the Windows Media Center. If you perform a clean driver installation (no previous NVIDIA drivers installed), you must reboot your computer. If you do not reboot, the predefined application profiles will not be activated and you may experience application stability problems. Windows XP 32-bit Issues nview Desktop Manager: Minimized applications cannot be restored when the application taskbar icon is clicked. You can work around this bug using either of the following methods: Right-click the application taskbar icon and then click Restore, or Disable all title bar buttons from the nview Desktop Manager User Interface tab. NVIDIA Control Panel->Workstation-> Frame Sync: The View Status Page does not detect which is the first and which is the second display attached to the GPU. Video color-space range for DVI-only 1 outputs is erroneously set to standard mode (16-235) instead of extended mode (0-255). A new detection feature to apply Standard CSC mode to TV outputs (including NTSC, PAL, 480i, and 576i), included DVI-only outputs by mistake. Note: The driver correctly applies extended mode to analog outputs, and standard mode to TV outputs (including NTSC, PAL, 480i, and 576i). A future driver release will correct this and apply the extended-mode color space to DVI-only outputs. You can work around this issue by forcing either standard or extended mode as follows: 1. DVI-only means only one display is connected, and it is to the DVI output. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 2

12 Open Windows XP Issues in Version a Launch regedit and determine the current primary display card by looking in HKey_Local_Machine\Hardware\DeviceMap\Video and note the GUID (global unique identifier assigned by Windows), which is the long string in brackets { } at the end of the entry "\device\video0". b Look in HKey_Local_Machine\SYSTEM\CurrentControlSet\Control\Video\{GUID}\0000 where {GUID} is the number derived from the previous step. c Open the "0000" directory and create a new DWORD called VMRCCCSStatus and give it a value of 0x3 - to force use of the standard YUV range of x1 - to force use of the extended YUV range of nview Desktop Manager needs the same functionality as provided by the Hummingbird Exceed Virtual Desktop style window management. Cinema 4D performance improvements are requested. Quadro 6000, Mantis: Random glitches occur when running the application. Quadro 4000: AVEVA PDMS when opened, the application stalls for a minute and then the crashes/restarts. Quadro FX 3700: SOCET GXP/SOCET Set 3D stereo effect is lost when panning or zooming. Windows XP 64-bit Issues Cinema 4D performance improvements are requested. Quadro FX 3700: SOCET GXP/SOCET Set 3D stereo effect is lost when panning or zooming. Quadro FX 1700: Catia certain models are faster without VBO. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 3

13 Not NVIDIA Issues Not NVIDIA Issues This section lists issues that are not due to the NVIDIA driver. AutoCAD 2009 SP2/SP3 the application crashes with recent OpenGL drivers. Linear interpolation on a 3D texture with format GL_RGBA32F_ARB produces banding. This is not an NVIDIA driver bug, but a normal result of the filtering methods used by the hardware. CATIA V5R18 there are no "Enable OpenGL Shader" options. This is not an NVIDIA bug, but rather an issue with Windows XP SP2. Windows Vista 64-bit: XSI - the application viewport doesn't refresh properly. This is not an NVIDIA bug, but rather an issue with the application. CATIAV5R18 Draft Analysis images are displayed incorrectly. This is not an NVIDIA bug, but rather an issue with the application. CATIA V5R17/18 the text in the Tool tree is not visible. This is a limitation in the application with some systems. CATIA V5R20 not all drawing elements appear if the drawing is created using Approximate mode. Quadro FX 1800: DDC communications does not work when using a DisplayPort-to- DVI dual-link active adapter. This is not an NVIDIA bug, but an issue with the adapter. Quadro FX 5600: Vega Prime 2.2 fog is not rendered properly where it intersects the terrain. Floating point 32-bit depth buffers are not supported on pre-opengl 3.0 supported GPUs. NVIDIA Quadro FX 570/1700: Catnap corrupts the projection matrix for the Reflect OpenGL Demo. This is not an NVIDIA bug, but an issue with the OS see Microsoft KB To work around this problem, do not put the computer into standby when it is running a program that performs intense floating-point calculations. SolidEdge (32-bit) the application cannot determine the driver version under a nonadministrator account. Solidworks 2009 Application profile is not shown in the NVIDIA Control Panel when SolidWorks 2009 is installed. This is an issue with the application shortcut. Quadro 4000/FX 4700/FX 3700: ShowCase 2011 Model right-click drop-down menu flickers when moving the mouse. Quadro 4000/FX 4800: CATIA V5R19 the product structure tree does not respond properly when the application is viewed on the secondary Dualview monitor. Dual Quadro FX 3700: MicroStation when both cards are set up in Spanning mode, an application runtime error occurs. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 4

14 Not NVIDIA Issues Quadro FX 5600/1700: System crashes or hangs when running Catia application. Quadro FX 4800: SPEC UG NX4 performance degradation is seen. The variation is within expected range. Quadro FX 4500: GL_LUMINANCE32F_ARB is not supported with glteximage2d. NVIDIA recommends using OpenGL 3.0 and Quadro FX 5600 cards or later for red channel format support. Quadro FX 570: Solidworks 2009 lines are covered when moving parts. Quadro FX 570, FX 1700 does not operate as secondary VGA. Quadro FX 1400: Cadence Allegro 16.0 UI performance is slow when using OpenGL. Quadro FX 3500: Large FBOs are not drawn properly when using low-memory graphics cards. Quadro FX 1700: 3dsMax2011 when panning an external application window over the viewport, artifacts appear on the time line. Quadro FX 1700: 3ds max fuzzy black shading appears on object faces at certain camera angles and orientation. Quadro FX 1700: CATIA 64-bit error reposting does not work. Quadro FX 1700: CATIA an update binding error occurs. Quadro FX 1700: CATIA V5 R18 the application crashes. Quadro FX 1700: Yamaha ESPRi CAD When testing dots and line, dots disappear intermittently. Quadro FX 3700/1700/570: The graphics cards do not work as the secondary GPUs. Quadro FX 880/380: Softimage CER the application crashes when selecting the gizmo of a specific scene. Quadro Plex D2: Opticore Studio 2010 the lighting surface blinks occasionally when using SLI Mosaic mode. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 5

15 Known Product Limitations Known Product Limitations This section describes problems that will not be fixed. Usually, the source of the problem is beyond the control of NVIDIA. Following is the list of problems and where they are discussed in this document: System Should not Enter Sleep/Hibernate Mode With SDI Capture in Progress on page 7 SDI Capture Driver Must be Installed Separately on page 7 Driver May not Work with /3GB Windows Switch When Using ECC on 32-bit OS on page 7 Professional 3D Stereo Left-Right Buffer Swap on page 8 Using HDMI/DisplayPort Audio with Displays that have a High Native Resolution on page 8 Using HDMI/DisplayPort Displays that do not Support Audio on page 9 Using HDMI/DisplayPort Audio in Dualview or Clone Mode Configurations on page 10 GPU Runs at a High Performance Level (full clock speeds) in Multi-display Modes on page Hz not Available on BenQ FP241W Monitors on page 10 Image Sharpening Control not Available with Quadro FX 4600 and Later GPUs on page 10 More Monitors are Listed in the Windows Device Manager than are Actually Connected on page 11 PowerDVD 5.0 Does Not Display Correctly in nview Span Mode on page 11 DirectX Fails When Detaching/Reattaching Displays in Dualview Mode on page 11 OpenGL Viewport Scaling Problem in Horizontal Span Mode on page 12 Video Playback in nview Clone and Span Modes on page 12 Monitor Ordering in the Windows Settings Page on page 13 No Antialiasing of 3DMark03 Image Quality Screen Captures on page 13 Windows XP/2000 Issue with Settings Tab Monitor Positioning on page 15 Antialiasing Problems With Certain Applications on page 15 Poor Quality S-Video Output on Some TVs on page 16 AGP and PCI-E Programs May Hang With AMD K7 and K8 Processors on page 16 Desktop Manager Does Not Re-Center Logon Screen on page 17 Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 6

16 Known Product Limitations System Should not Enter Sleep/Hibernate Mode With SDI Capture in Progress SDI capture programs will become non-responsive upon resume from sleep or hibernate modes. This is not a typical use case, so power management tests shouldnot be performed when testing SDI. SDI Capture Driver Must be Installed Separately To use the Quadro SDI Capture card, you need to install the NVIDIA WDM driver for the Quadro SDI Capture card after installing the Quadro professional driver. If you later install a different Quadro professional driver version for example, when upgrading from a Release 260 driver to a Release 265 driver make sure to reinstall the WDM driver from Release 265 as well. The WDM driver version must be from the same branch as the installed NVIDIA graphics driver. Failure to follow this sequence can result in a faulty driver installation. Driver May not Work with /3GB Windows Switch When Using ECC on 32-bit OS Problem With ECC control enabled from the NVIDIA Control Panel, the driver may not start up properly if the /3BG switch was used in the Windows Boot.ini file. This issue occurs on Windows XP 32-bit. Explanation and Resolution The /3GB boot.ini startup switch grants more user virtual address space while reducing the amount of Windows kernel virtual address space. With ECC enabled, the driver's memory usage may exceed the reduced, available kernel virtual address space. This out-of-memory condition may prevent the driver from starting normally. To resolve this issue, use Windows XP 64-bit or avoid using the /3GB switch (may be required for some workstation applications). Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 7

17 Known Product Limitations Professional 3D Stereo Left-Right Buffer Swap When displaying stereoscopic 3D, NVIDIA GPUs are capable of updating left and right eye views after each field is displayed. This is advantageous with certain types of stereoscopic 3D content such as fast moving objects because it allows the objects to move as smoothly as possible across the screen with fewer jumps between fields. In certain situations, however, updating the left and right views after each field may be problematic such as when applications expect both left and right fields to be displayed as a pair. In this case, updating the left-right pair per field may cause blurriness on the displayed image since the application-generated fields get out of step with the displayed fields. This effect can be more noticeable on projectors that double pump the displayed frames. In these situations, a suggested workaround is to use WGL_EXT_swap_control to set the swap interval via wglswapintervalext(2). This ensures that the left-right views are not replaced at every field, but rather at every frame. This workaround, however, has the following caveats: The maximum effective frame rate is limited to half of the refresh rate. It does not guarantee that the left and right eye views are always presented in that order. Sometimes, the fields are presented in right-left order. This happens when the leftright views are updated with the next frame after presentation of the left eye view. NVIDIA is working to provide a solution in a future driver release that will provide the option for frames to be updated either per-field or per-frame. Using HDMI/DisplayPort Audio with Displays that have a High Native Resolution To use HDMI/DisplayPort audio with some displays that have a native resolution higher than 1920x1080, you must set the display to a lower HD resolution. Some HDMI TV's have a native resolution that exceeds the maximum supported HD mode. For example, TVs with a native resolution of 1920x1200 exceed the maximum supported HD mode of 1920x1080. Applying this native mode results in display overscan which cannot be resized using the NVIDIA Control Panel since the mode is not an HD mode. To avoid this situation and provide a better user experience, the driver treats certain TVs such as the Viewsonic VX2835wm and the Westinghouse LVM- 37w3 as a DVI monitor when applying the native mode. Because the driver does not treat the TV as an HDMI in this case, the HDMI audio is not used. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 8

18 Known Product Limitations Using HDMI/DisplayPort Displays that do not Support Audio Some HDMI/DisplayPort displays do not support audio, or have issues with Quadro FX family and earlier NVIDIA graphics cards. The NVIDIA driver attempts to identify such displays and automatically disables the audio. For example, the NVIDIA driver disables HMDI audio for all Philips HDMI TVs, as these have been identified as having issues with Quadro FX family and earlier NVIDIA graphics cards. There may be cases where either the driver disables audio even though there is no problem, or does not disable the audio when in fact the audio does not work. The following sections describe these situations and provides guidance for handling them. Corrupted video and no audio The driver has not disabled audio and the display s audio signal is incompatible with the graphics card, causing video corruption. With a different display connected in order to establish video, disable audio for the HDMI display using the NVIDIA Control Panel-> Change Resolution page. From the connector list, select HDMI-HDTV (Audio Disabled). Video but no audio Check the connector list on the NVIDIA Control Panel->Change Resolution page. If HDMI-HDTV (Audio Disabled) is selected and you want to test whether your HDMI audio does, in fact, work, then select HDMI-HDTV (Audio Enabled) and the driver will prompt you with instructions for testing HDMI audio with the display. If HDMI-HDTV (Audio Enabled) is selected, then the driver has not successfully detected that an incompatible display is connected. Future drive versions will properly identify such displays and disable audio. If there is no HDMI connector option in the NVIDIA Control Panel->Change Resolution page, the display does not support audio and has properly reported this to the NVIDIA driver. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 9

19 Known Product Limitations Using HDMI/DisplayPort Audio in Dualview or Clone Mode Configurations Two Audio-enabled Ports In a multi-display configuration where both HDMI/DisplayPort audio ports are enabled, only the primary display will provide the audio. One Audio-enabled Port In a multi-display configuration where only one audio port is enabled, such as when one display is a DVI display, then the HDMI/DisplayPort display can provide the audio whether is it the primary or secondary display. GPU Runs at a High Performance Level (full clock speeds) in Multi-display Modes This is a hardware limitation and not a software bug. Even when no 3D programs are running, the driver will operate the GPU at a high performance level in order to efficiently drive multiple displays. In the case of SLI or multi-gpu PCs, the second GPU will always operate with full clock speeds; again, in order to efficiently drive multiple displays. Today, all hardware from all GPU vendors have this limitation. 60 Hz not Available on BenQ FP241W Monitors Even though the monitor EDID lists 60 Hz, the screen turns blank when using an HDMI connection. This is an issue with the monitor and not the NVIDIA driver. Because of this issue with the monitor, the NVIDIA driver blocks the problem mode 60 Hz) and makes it unavailable. Image Sharpening Control not Available with Quadro FX 4600 and Later GPUs With Quadro FX 4600 and later graphics cards, the Image sharpening slider on the NVIDIA Control Panel-> Display->Adjust Desktop Color Settings page is grayed out. This control is intentionally disabled because image sharpening is not supported on Quadro FX 4600 and later GPUs. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 10

20 Known Product Limitations More Monitors are Listed in the Windows Device Manager than are Actually Connected Problem Many monitors are listed in the Windows Device Manager hardware tree even when only a few are actually connected or enabled. Explanation NVIDIA chooses to expose all potential monitors even though they are not yet connected. Such an implementation makes multiple device handling easier in certain situations, such as when a user unplugs a monitor and plugs another one in at a different port. The only impact is a cosmetic in the plug-and-play manager. There is no functional impact at all and the GDI is not aware of the multiple monitor listing. PowerDVD 5.0 Does Not Display Correctly in nview Span Mode With nview Horizontal Span mode enabled, when the PowerDVD 5.0 playback window is dragged to the second display and then stretched to fill the display, the right area of the display is corrupted. This is not an NVIDIA bug, but a problem with PowerDVD. DirectX Fails When Detaching/Reattaching Displays in Dualview Mode This problem can be duplicated as follows: 1 Enable both displays in Dualview mode. 2 Detach monitor 2 and apply settings. 3 Reattach monitor 2 and apply settings. DirectX runtime fails on monitor 1. This is not an NVIDIA bug, but a limitation in the operating system where DirectX does not enumerate the second device. DirectX can be restored to both displays by rebooting the system Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 11

21 Known Product Limitations OpenGL Viewport Scaling Problem in Horizontal Span Mode With nview Horizontal Span mode enabled, when opening an OpenGL model in a viewport, the model image is scaled too large to fit in the viewport. The problem occurs with such applications as Maya 5.0 and 3D Studio MAX This is not an NVIDIA bug, but a limitation in the application s ability to properly maintain the aspect ratio in Horizontal Span mode. Video Playback in nview Clone and Span Modes Problem With nview Clone or Span mode enabled, video playback appears on only one display under the following conditions: Under nview Clone mode, when full-screen video mirror is not used. Under nview Span mode, when full-screen video mirror is not used and the video is positioned to span across both monitors. Explanation With applications that render using the hardware overlay such as DirectX applications the default driver behavior is to enable the hardware overlay when nview Clone or Span mode is enabled. Because the driver supports only one hardware overlay, the video appears on only one display. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 12

22 Known Product Limitations Monitor Ordering in the Windows Settings Page Monitor Ordering on a Single GPU Issue The monitor order in the Display Properties Settings page is not consistently matched with the connectors on the graphics card. Explanation The driver does not distinguish connector positions, but instead distinguishes the display type, and consequently assigns monitor numbers according to the display type and not according to the connector. Monitor Ordering on a Multiple GPU System Issue When four monitors are connected to a system with multiple PCI GPUs, such as a NVIDIA Quadro NVS 400 graphics card, and enabled in Dualview mode, many customers expect the monitor ordering in the Display Properties Settings page to conform to the following: Connector Position Primary GPU Output 1 1 Primary GPU Output 2 2 Secondary GPU Output 1 3 Secondary GPU Output 2 4 Monitor Number The monitor ordering, in fact, does not conform to this scheme. Explanation The monitor ordering is not controlled by the driver, but rather by the Windows OS method of enumerating PCI devices. The Windows enumeration results in the following monitor numbering: Connector Position Monitor Number Primary GPU Output 1 1 Seconday GPU Output 1 2 Primary GPU Output 2 3 Secondary GPU Output 2 4 Considerations for nview Span Modes: Outputs from the same GPUs are grouped together in nview Span modes, resulting in the desktop spanning across monitors 1 and 3, or across 2 and 4. No Antialiasing of 3DMark03 Image Quality Screen Captures Problem Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 13

23 Known Product Limitations After enabling antialiasing from the NVIDIA Properties page, 3DMark03 screen captures obtained using the application s screen capture function might not be antialiased. Explanation This is not an NVIDIA bug, but rather a result of different methods used to render antialiased images. Depending on a combination of factors, the driver may take advantage of the NVIDIA hardware s ability to bypass the front buffer while rendering an antialiased image. In this case, the front buffer does not contain antialiased data, so if an application takes data from the front buffer as is the case with 3DMark03 s Image Quality screen captures then the resulting image is not antialiased. To accommodate applications that request use of the front buffer, the NVIDIA software can provide the antialiased data in a buffer to the application. Since this negates the advantages of the NVIDIA hardware capability, this support is enabled only when antialiasing is enabled within the application, and not from the NVIDIA control panel. In all cases when antialiasing is enabled, screen images as well as screen captures obtained using the Print Screen key are always antialiased. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 14

24 Known Product Limitations Windows XP/2000 Issue with Settings Tab Monitor Positioning Problem In the Windows Display Properties > Settings tab, the secondary monitors cannot be positioned directly above monitor #1 without snapping horizontally to a position diagonal to monitor #1. When the Problem Occurs The problem occurs when four monitors are connected to the graphics adapter card, but only two of them are enabled. Cause and Workaround This is a Microsoft not an NVIDIA bug, and there is no workaround to correct the positioning of the monitor icons. However, the actual positioning of the displays on the desktop can be corrected using the nview Desktop Manager window as follows: a Under the Tools tab in the Desktop Manager windows, make sure Automatically Align Displays is checked. b In the Settings tab, position the appropriate monitor icon above monitor #1, then click Apply. The mouse cursor movement between monitor desktops will correspond to a vertical orientation of the monitors, even though the monitor icons in the Settings tab are diagonal to each other. Note: This will be the case even if the monitor icons are deliberately positioned diagonal to each other. Antialiasing Problems With Certain Applications Antialiasing in the NVIDIA Direct3D driver requires each new frame to be rendered from scratch. This requirement adversely affects applications that render only that portion of the content that has changed since the last frame. A common symptom of this problem is geometric structures that incorrectly disappear and re-appear as the scene shifts. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 15

25 Known Product Limitations Poor Quality S-Video Output on Some TVs NVIDIA drivers differentiate an S-video TV from a composite TV by searching for 75- Ohm loads on the chrominance and luminance lines. If the driver detects only one such load, it assumes that it has a composite TV and drives both chroma and luma onto that line. This approach allows both types of TV to display in color. Unfortunately, some S-video TVs do not apply the correct load to both lines, causing the driver to detect an S-video TV as a composite. The driver, in turn, sends the lower quality signal to the S-video TV. To work around this problem, use the Control Panel to override the Auto-select feature. This can be done following these steps: 1 In the Settings tab of the Display Properties Control Panel, click Advanced. 2 In the nview tab, click Device Settings and click Select Output Device. 3 In the Device Selection tab, click the TV option. 4 Change the Video output format to S-video. AGP and PCI-E Programs May Hang With AMD K7 and K8 Processors Issue Microsoft Windows 2000 and Windows XP systems using AMD K7 and K8 processors can hang when an AGP or PCI-E program is used. Root Cause There is a known problem with Microsoft Windows 2000 and Windows XP systems using AMD K7 and K8 CPUs that results in the Microsoft operating system allocating overlapping 4M cached pages with 4k write-combined pages. This condition results in undefined behavior and data corruption, and is explicitly disallowed by the AMD CPU manual. This problem can affect any device driver in the system that allocates write-combined system memory, but is usually most easily reproduced with graphics drivers since graphics drivers generally make heavy use of write-combined system memory for performance reasons. Resolution Microsoft has a knowledge base article on the issue, the text of which is unfortunately quite outdated. While the article only mentions Windows 2000, AGP, and K7, both the root cause and resolution also apply to Windows 2000 or Windows XP, AGP or PCI-E, and AMD K7 or K8. The article can be found at The issue is resolved by applying an operating system registry key as described in the referenced article that instructs the Microsoft operating system to not use the 4M pages, thus avoiding the conflict. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 16

26 Known Product Limitations The registry key is automatically applied by installation of the latest NVIDIA nforce platform driver package (including 4.57 SMBUS or later). It is imperative for the package to be installed or for the registry key to be applied before the NVIDIA graphics driver or any other device drivers are installed. The registry key takes effect only after an operating system reboot. Desktop Manager Does Not Re-Center Logon Screen On Windows XP multi-display systems that are set to nview Span mode, the Windows logon screen is centered on the extended desktop. This usually causes it to be split across two displays, which users may find annoying. Although users can normally use the Desktop Manager to restrict a window s appearance to one display, security restrictions in the operating systems prevent this in the case of the logon screen. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 17

27 03 THE RELEASE 304 DRIVER FOR WINDOWS XP This chapter covers the following main topics: Hardware and Software Support on page 18 Driver Installation on page 25 Hardware and Software Support Supported Operating Systems This Release 304 driver includes drivers designed for the following Microsoft operating systems: Microsoft Windows XP Windows XP Professional Windows XP Home Edition Windows XP Professional x64 Edition Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 18

28 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP Supported NVIDIA Products The following tables list the NVIDIA products supported by the Release 304 driver, version Table 3.1, Supported NVIDIA Quadro & NVS Products on page 19 Table 3.2, Supported NVIDIA Quadro G-Sync Products on page 21 Table 3.3, Supported NVIDIA Quadro G-Sync II Products on page 21 Table 3.4, Supported NVIDIA Quadro SDI Products on page 21 Table 3.5, Supported NVIDIA Quadro Plex Products on page 22 Table 3.6, Supported NVIDIA Quadro Blade/Embedded Graphics Board Series on page 22 Table 3.7, Supported NVIDIA Tesla Products on page 23 NVIDIA Quadro & NVS Products Table 3.1 Supported NVIDIA Quadro & NVS Products Product NVIDIA Quadro 6000 NVIDIA Quadro 5000 NVIDIA Quadro 4000 NVIDIA Quadro 2000D NVIDIA Quadro 2000 NVIDIA Quadro 600 NVIDIA Quadro 400 NVIDIA Quadro FX 5800 NVIDIA Quadro FX 5600 NVIDIA Quadro FX 5500 NVIDIA Quadro FX 4800 NVIDIA Quadro FX 4700 X2 NVIDIA Quadro FX 4600 NVIDIA Quadro FX 4500 X2 NVIDIA Quadro FX 4500 NVIDIA Quadro FX 4000 NVIDIA Quadro FX 3800 NVIDIA Quadro FX 3700 NVIDIA Quadro FX 3500 NVIDIA Quadro FX 3450 NVIDIA Quadro FX 1800 Notes Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 19

29 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP Table 3.1 Supported NVIDIA Quadro & NVS Products (continued) Product NVIDIA Quadro FX 1700 NVIDIA Quadro FX 1500 NVIDIA Quadro FX 1400 NVIDIA Quadro FX 580 NVIDIA Quadro FX 570 NVIDIA Quadro FX 560 NVIDIA Quadro FX 550 NVIDIA Quadro FX 540 NVIDIA Quadro FX 470 NVIDIA Quadro FX 380 NVIDIA Quadro FX 380 LP (low profile) NVIDIA Quadro FX 370 NVIDIA Quadro FX 370 low profile NVIDIA Quadro FX 350 NVIDIA Quadro VX 200 NVIDIA Quadro CX NVIDIA NVS 300 NVIDIA Quadro NVS 450 NVIDIA Quadro NVS 440 NVIDIA Quadro NVS 420 NVIDIA Quadro NVS 295 NVIDIA Quadro NVS 290 NVIDIA Quadro NVS 285 Notes Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 20

30 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP NVIDIA Quadro G-Sync Products Table 3.2 Supported NVIDIA Quadro G-Sync Products Product NVIDIA Quadro FX 5500 NVIDIA Quadro FX 4500 X2 NVIDIA Quadro FX 4500 Notes NVIDIA Quadro G-Sync II Products Table 3.3 Supported NVIDIA Quadro G-Sync II Products Product NVIDIA Quadro 6000 NVIDIA Quadro 5000 NVIDIA Quadro FX 5800 NVIDIA Quadro FX 4800 NVIDIA Quadro FX 5600 NVIDIA Quadro FX 4600 Notes NVIDIA Quadro SDI Products Table 3.4 Supported NVIDIA Quadro SDI Products Product NVIDIA Quadro 6000 SDI NVIDIA Quadro 5000 SDI NVIDIA Quadro 4000 SDI NVIDIA Quadro FX 5800 SDI NVIDIA Quadro CX SDI NVIDIA Quadro FX 5600 SDI NVIDIA Quadro FX 4800 SDI NVIDIA Quadro FX 4600 SDI NVIDIA Quadro FX 3800 SDI Notes Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 21

31 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP NVIDIA Quadro Plex Products Table 3.5 Supported NVIDIA Quadro Plex Products Product NVIDIA Quadro Plex 7000 NVIDIA Quadro Plex D Series NVIDIA Quadro Plex Model II NVIDIA Quadro Plex Model IV Notes NVIDIA Quadro Blade/Embedded Graphics Boards Table 3.6 Supported NVIDIA Quadro Blade/Embedded Graphics Board Series Product NVIDIA Quadro FX 3600M NVIDIA Quadro FX 2800M NVIDIA Quadro FX 1600M NVIDIA Quadro FX 880M NVIDIA Quadro FX 770M NVIDIA Quadro FX 560M NVIDIA Quadro FX 370M NVIDIA Quadro NVS 120M Notes Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 22

32 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP NVIDIA Tesla Products The Tesla driver package is designed for systems that that have one or more Tesla products installed. Only one GHIC can be connected to the server in a Tesla system. This release of the Tesla driver supports CUDA C/C++ applications and libraries that rely on the CUDA C Runtime and/or CUDA Driver API. Table 3.7 Product Supported NVIDIA Tesla Products Notes Tesla S-Class Products NVIDIA Tesla S2050 NVIDIA Tesla S1070 Tesla M-Class Products NVIDIA Tesla M2090 NVIDIA Tesla M2075 NVIDIA Tesla M2070 NVIDIA Tesla M2070Q NVIDIA Tesla M2050 NVIDIA Tesla M1060 Tesla C-Class Products NVIDIA Tesla C2075 NVIDIA Tesla C2070 NVIDIA Tesla C2050 NVIDIA Tesla C1060 Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 23

33 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP Supported Languages The Release 304 Graphics Drivers supports the following languages in the main driver Control Panel: English (USA) German Portuguese (Euro/ Iberian) English (UK) Greek Russian Arabic Hebrew Slovak Chinese (Simplified) Hungarian Slovenian Chinese (Traditional) Italian Spanish Czech Japanese Spanish (Latin America) Danish Korean Swedish Dutch Norwegian Thai Finnish Polish Turkish French Portuguese (Brazil) Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 24

34 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP Driver Installation System Requirements The hard disk space requirement for 32 bit is minimum 150 MB for English-only, and 230 MB for International. The hard disk space requirement for 64 bit is minimum 207 MB for English-only, and 300 MB for International. Installation Instructions Before You Begin If NVIDIA ntune is already installed If you have previously installed NVIDIA ntune, NVIDIA recommends that you uninstall ntune before installing this driver. After the driver install is complete, you can reinstall ntune. If you do not have System Administrator access privileges, it is assumed that the appropriate person with System Administrator access in your organization will set up and install the NVIDIA graphics driver software on your computer. The installation process copies all necessary files for operation into the appropriate directories. The nview system files are copied to your Windows\System directory. nview Desktop Manager Profile files (*.tvp) are saved in the Windows\Nview directory. Depending on the version of the NVIDIA driver previously installed, profiles may also be located in the Documents and Settings\All Users\Application Data\ nview_profiles directory. As part of the install process, an uninstall is registered in your system. Under Windows XP, the NVIDIA driver is installed in Dualview mode display. However, note that the second display is not activated by default, but must be enabled. SLI Mosaic Mode You must make sure SLI Mosaic mode is disabled before installing a new driver over a previously installed driver. If SLI Mosaic mode is active on your displays when you install the new driver, the driver will not install properly. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 25

35 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP Preserving Settings Before Upgrading Your Software Before uninstalling or installing software, your can preserve your nview Desktop Manager and/or NVIDIA Display settings by using the nview Desktop Manager Profiles features. Note: Follow the steps below and/or refer to the NVIDIA nview Desktop Manager User s Guide for details. Under Windows XP/2000 you must have, at least, Power User access privileges in order to create or save a profile. (Refer to Windows Help if you need an explanation of Power User access rights.) Follow the steps below and/or refer to the NVIDIA nview Desktop Manager User s Guide for details. 1 Open the nview Desktop Manager Profiles page (Figure 4.1). 2 To preserve your current settings, you can use either the Save or the New option from the nview Desktop Manager Profiles page: If you want to overwrite the currently loaded profile with your changed settings, use the Save option. Notice that a warning message indicates that you are about to overwrite the selected profile. If you want to retain the currently loaded profile and want to save your changed settings to a new file, click the New option. Enter a name and description of the profile in the New Profile dialog box. For example, you can name this profile My Settings. 3 If you are an advanced user and want to customize certain settings in the saved profile, click Advanced << to expand the dialog box (Figure 4.2). 4 To customize the settings, you can select or clear any of the settings check boxes. 5 Click Save to return to the main Profiles page. If you created a new profile, you will see the name of the newly created profile in the profiles list. If you overwrote a current profile, the same profile name is retained in the list. Note: nview Desktop Manager profile (.tvp) files are saved in the Windows\nView directory. Depending on the version of the NVIDIA driver previously installed, profiles may also be saved in the Documents and Settings\All Users\Application Data\ nview_profiles directory. 6 Now you can uninstall your current driver for a driver upgrade. 7 After you restart your computer following an NVIDIA new driver install, you can easily load the saved profile from the Profiles page of nview Desktop Manager. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 26

36 Chapter 03 : THE RELEASE 304 DRIVER FOR WINDOWS XP About Using Saved Profiles in Another Computer You can easily use any saved profile (.tvp file in the Windows\nView directory) from one computer and use it in another computer, if you want. You ll need to copy it to the Windows\nView directory of a computer that has the NVIDIA ForceWare graphics display driver, etc. installed properly. Then this profile can be loaded from another computer from the nview Desktop Manager Profiles page just as it can from your original computer. Installing the NVIDIA Graphics Drivers 1 Follow the instructions on the NVIDIA.com Web site driver download page to locate the appropriate driver to download, based on your hardware and operating system. 2 Click the driver download link. The license agreement dialog box appears. 3 Click Accept if you accept the terms of the agreement, then either open the file or save the file to your PC and open it later. 4 Open the NVIDIA driver installation.exe file to launch the NVIDIA InstallShield Wizard. 5 Follow the instructions in the NVIDIA InstallShield Wizard to complete the installation. Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 27

37 APPENDIX A MODE SUPPORT FOR WINDOWS This chapter details the Windows modes supported by the Release 304 driver for NVIDIA products. It contains these sections: General Mode Support Information on page 29 Default Modes Supported by GPU for Windows XP on page 30 Modes Supported by TV Encoders on page 36 Release 304 Tesla, Quadro & NVS Professional Drivers for Windows - Version RN-WQ _v01 28