Industrial Monitors and Accessories

Transcription

1 Industrial Monitors and Accessories NI FPT-15 Rugged industrial monitor for PXI and NI Compact Vision Systems 15 in. XGA TFT color LCD flat panel monitor Resistive touch screen for PXI 24 x 768 maximum resolution 250 cd/m 2 maximum luminance Abrasion-resistant tempered glass Front-panel controls for display settings Standard VGA interface Autorecognition of input signal Up to 40 m extended-length VGA cable(s) Communication ports Device side USB for touch screen control Works with Windows 2000/NT/XP drivers Stainless steel chassis with Al-Mg front panel NEMA4/IP65-compliant front panel Panel wall, or desk mount Extended temperature range to 50 C CE and UL certifications Accessories Rack-mount kit Wall/desk-mount kit The National Instruments FPT-15 is an industrial 15 in. color TFT LCD flat panel touch screen monitor. Its large display area, VGA compatibility, and interactive touch screen interface make it the ideal human-machine interface (HMI) for high-performance PXI test applications and machine vision applications based on the NI CVS- 145x systems. Ordering Information NI FPT Rack mount kit Desk mount kit NI FPM in. VGA flat panel Planar monitor Built-in 0 to 240 VAC (50/60 Hz) power supply UL, TUV-GS, and CE Mark Desktop stand included; VESA compatible Monitor The National Instruments FPM-17 is a 17 in. flat panel monitor with high resolution and bright color contrast, ideal for developing PXI applications. The monitor connects through standard VGA input to embedded PXI controllers running Windows 2000/XP. The NI FPT- 17 provides and active matrix flat panel display with 1280 x 24 resolution and a built-in power supply. It accepts 0 to 240 VAC power and comes with a 120 VAC North American power cord. Add another power cord to accommodate power in other regions. The FPM-17 also works with any VGA-compatible PC running Windows 2000/XP. The FPM-17 is a Planar monitor. NI FPM in. widescreen flat panel NEC monitor 1440x900 at 60 to 75 Hz native resolution Desktop stand included; VESA compatible DVI-D and VGA inputs for digital or analog input 00:1 contrast ratio (typical) and 5 ms response time (typical) Built-in 0 to 240 VAC (50/60 Hz) power supply The NI FPM-19 is a 19 in. widescreen flat panel LCD monitor with high resolution and bright color contrast that is ideal for developing PXI applications. The monitor connects through a standard VGA or DVI interface to embedded PXI controllers running Windows Vista/XP OS. The FPM-19 provides an active matrix flat panel display with 1400x900 resolution and a built-in power supply. It accepts 0 to 240 VAC power and comes with a 120 VAC North American power cord. Add another power cord to accommodate power in other regions. A VGA to VGA monitor cable is included with the monitor. A DVI-I to DVI-I monitor cable is available as an accessory. Industrial Monitors and Accessories 455

2 Industrial Panel PCs with 5.7 in. and 15 in. Touch Screens NI TPC in. QVGA STN LCD industrial panel PC 266 MHz low power consumption ARM processor Analog resistive touch screen Memory 64 MB SDRAM onboard CompactFlash 2.0 expansion slot Windows CE.NET 4.2 embedded OS Networking capable Remote terminal services LabVIEW PDA-based application programming Communication ports 3 serial ports: (2) RS232 and (1) RS485 1 Ethernet (/0BaseT) 2 USB ports (1 host, 1 client) Panel mount NEMA4/lP65-compliant front panel Extended temperature range to 50 C CE, FCC, and UL certifications The National Instruments TPC-2006 is an industrial panel computer with 5.7 in. STN LCD touch screen monitor. Low power consumption, high performance, and rugged design make it an ideal operator interface for embedded control systems with NI Compact FieldPoint, CompactRIO, industrial DAQ, and the Compact Vision System. Ordering Information NI TPC Accessories NI PS-5 Power Supply NI LabVIEW Touch Panel Module for Windows CE A-09 Industrial Panel PCs with 5.7 in. and 15 in. Touch Screens NI PPC GHz Pentium 4 processor, 512 MB RAM 40 GB hard drive, CD-ROM, and floppy drive Expansion slots for 2 half-length PCI boards 15 in. XGA/TFT color LCD touch screen NEMA4/IP65-compliant front panel Communication ports 1 Ethernet, 5 USB 2.0, 2 RS232, 2 PCMCIA (type ), 2 IEEE 1394, 2 PS/2 NI PPC GHz Intel Celeron M processor, 40 GB hard drive, and 512 MB RAM Fanless cooling with 0 to 50 C operating range 15 in. XGA TFT color LCD Thin 2.5 in. depth to save panel space Gigabit and fast Ethernet support NEMA4/IP65-compliant front panel The NI PPC-2015 is an industrial panel PC with a touch screen. The NI PPC-25 combines a 2 GHz Pentium 4 that works with a wide range of NI software and a rugged 15 in. touch screen. This combinaions creates an ideal industrial-grade HMI system for NI programmable automation controllers (PACs). When configured with NI LabVIEW software, it provides a complete HMI solution. The NI PPC-2115 is a fanless industrial panel PC with a built-in touch screen. The NI PPC-2115 offers a thin 2.5 in. display to save panel space and a 1 GHz Celeron M processor with a rugged 15 in. TFT color LCD display for large human machine interface (HMI) applications. Combine the NI LabVIEW Datalogging and Supervisory Control Module with the PPC-2115 to deploy LabVIEW front panels. 456

3 12 in. and 6 in. LabVIEW Touch Panel Computer with Windows CE NI TPC MHz processor running Windows CE 256 MB DDR SDRAM and 128 MB CompactFlash with Windows CE installed Communications ports - 1 Ethernet (1/0BaseT), 2 Hi-Speed USB, 3 RS232, 1 RS232/485 NEMA4/IP65-compliant front panel 12.1 in. SVGA TFT LCD touch screen LabVIEW Touch Panel Module certified; includes 1 Touch Panel Deployment License The NI TPC-2012 touch panel computer provides a high-quality 12.1 in. TFT 800x600 LCD display and touch screen. The NI TPC-2012 runs Windows CE on a 500 MHz Gx3 with 256 MB DDR SDRAM for feature-rich HMI development with NI environments and is compatible with the LabVIEW Touch Panel Module. The TPC-2012 uses shared variables for communication to LabVIEW Real-Time PACs and uses Modbus TPC/IP or Modbus ASCII for communication to third-party PACs and PLCs. The TPC-2012 offers serial ports and the LabVIEW Touch Panel Module works with NI-VISA for RS232/485 communication to external serial devices. NI TPC-26/T 416 MHz Intel XScale processor running Windows CE 64 MB SDRAM and 64 MB onboard flash Display options: STN LCD (TPC-26) or improved quality TFT LCD touch screen (TPC-26T) Connectivity-1 Ethernet, 2 USB 1.1 ports (1 host, 1 client), 2 RS232, and 1 RS485 NEMA4/IP65-compliant front panel Touch Panel Deployment License The NI TPC-26 and TPC-26T touch panel computers (TPCs) provide an industrial touch panel display with a 416 MHz Intel XScale processor, rugged solid-state hard drives, and the embedded Windows CE operating system. These TPCs feature two display options. The TPC-26 offers an entry-level 5.7 in. STN LCD touch screen, and the TPC-26T provides a 5.6 in. TFT LCD with improved contrast, luminance, and brightness. Both the TPC-26 and TPC-26T work with the NI LabVIEW Touch Panel Module and appear as targets in the LabVIEW Project. A TPC- 26T offers a NEMA4 and IP65-rated front panel for wash down or humid environments and is an ideal size for an embedded machine HMI or for a vehicle operator. 12 in. and 6 in. LabVIEW Touch Panel Computer with Windows CE 457

4 12 in. LabVIEW Touch Panel Computer with Windows XP Embedded NI TPC in. LCD touch screen Windows XP Embedded on a 4GB CompactFlash card 500 MHz and 512 MB DDR SDRAM memory Connectivity through 2 Hi-Speed USB ports, 1 Ethernet port, and 4 serial ports Support for USB data acquisition (DAQ), NI CompactDAQ, NI CompactRIO, and NI Single-Board RIO LabVIEW Touch Panel Module certification, with one Touch Panel Deployment License The NI TPC-2512 touch panel computer (TPC) features a 12.1 in. LCD touch screen and a 500 MHz processor. It is shipped with Windows XP Embedded installed on a 4GB CompactFlash card with 512 MB SDRAM. For out-of-box connectivity to NI CompactDAQ and all NI USB DAQ devices compatible with NI-DAQmx measurement services software, the TPC-2512 is certified to work with the NI LabVIEW Touch Panel Module and includes on Touch Panel Deployment License. From the LabVIEW Project, you can detect the TPC-2512 over Ethernet and then update IP settings and add the device to your project. 15 in. LabVIEW Touch Panel Computer with Windows XP Embedded 12 in. LabVIEW Touch Panel Computer with Windows XP Embedded NI TPC-2515 LabVIEW Touch Panel Module certification and license included 15 in. XGA TFT color LCD Windows XP Embedded on a 4 GB CompactFlash card 1 GHz Intel Celeron M processor with 1 GB memory (RAM) Connectivity through 1 Gigabit Ethernet, 2 Hi-Speed USB, 1 Ethernet, and 4 serial ports Support for USB data acquisition (DAQ), NI CompactDAQ, NI CompactRIO, and NI Single-Board RIO The NI TPC-2515 touch panel computer (TPC) features a 15 in. LCD touch screen and a 1 GHz Intel Celeron M processor. It is shipped with Windows XP Embedded OS installed on a 4 GB CompactFlash card with 1 GB memory (RAM). For advanced human machine interface (HMI) applications, the TPC-2515 is certified to work with the NI LabVIEW Touch Panel Module and includes one Touch Panel Deployment License. For applications that require alarming, local logging, and industrial images upgrade to the NI TPC-2515D which is certified to work with the LabVIEW Datalogging and Supervisory Control (DSC) Module, comes preinstalled with the LabVIEW DSC Run-Time Engine and support files, and includes a LabVIEW DSC Deployment License. Both devices provide support for NI CompactDAQ and NI USB DAQ devices compatible with NI-DAQmx measurement services software. The TPC-2515 and TPC-2515D offer a wide range of connectivity options including one Gigabit Ethernet, one Fast Ethernet, two Hi- Speed USB, two RS232, one RS485, and one parallel port. The TPC-2515 also features one PS2 port for mouse or keyboard connectivity and one CompactFlash slot for removable data-logging storage. 458

5 Single and Dual-Core Industrial Controller with Windows OS NI 30, NI 30RT Rugged, high-performance, fanless industrial controller 1.06 GHz Intel Celeron M processor 0 to 50 C operating temperature without PCI or PCI Express board NI 30 Windows XP on an 80 GB SATA HDD with 1 GB DDR 2 memory NI 30RT 1 GB solid state driver (SSD) for storage and 1 GB DDR 2 memory The NI 30 industrial controller is a rugged, fanless PC that offers you a wide range of expansion options to other NI platforms. It features a 1.06 GHz Intel Celeron M processor with 1 GB DDR 2 memory, an 80 GB or larger SATA hard disk drive (HDD), and Windows XP. The NI 30RT industrial controller is an embedded fanless controller with support for LabVIEW Real-Time and a wide range of expansion options to other LabVIEW Real-Time platforms including NI CompactRIO, NI deterministic expansion I/O, and NI plug-in data acquisition devices. NI 31, NI 31RT, NI 31 with NI Real-Time Hypervisor Rugged, high-performance, fanless industrial controller 1.66 GHz Intel Core Duo processor 0 to 50 C operating temperature without PCI or PCI Express board NI 31 Windows XP on an 80 GB SATA HDD with 1 GB DDR 2 memory NI 31RT 1 GB solid state driver (SSD) for storage and 1 GB DDR 2 memory NI 31 with NI Real-Time Hypervisor Run LabVIEW Real-Time applications and Windows XP simultaneously on one controller Combine deterministic real-time processing and a rich user interface in a single consolidated system 80 GB SATA HDD and expanded 2 GB DDR 2 memory The NI 31 industrial controller is a rugged, fanless PC that offers you a wide range of expansion options to other NI platforms. It features a 1.66 GHz Intel Core Duo processor for applications that require high-speed processing and analysis as well as multicore processing. The dual-core controller provides 1 GB DDR 2 memory, an 80 GB SATA hard disk drive (HDD), and Windows XP. Single and Dual-Core Industrial Controller with Windows OS 459

6 Wireless Sensor Network Ethernet Gateway NI WSN-9791 NI-WSN software provides easy network configuration and data extraction 2.4 GHz, IEEE radio to communicate with measurement nodes /0 Mbits/s Ethernet port for flexible connectivity to Windows PCs or LabVIEW Real-Time programmable automation controllers (PACs) Up to 300 m outdoor range with line of sight Supports up to 36 measurement nodes 9 to 30 VDC power input Industrial ratings: -30 to 70 C operating temperature 50 g shock, 5 g vibration Panel and DIN-rail mounting options available Operating Systems Windows 7/Vista/XP/2000 LabVIEW Real-Time Software Support LabVIEW Driver and Configuration Software (included) NI-WSN software Measurement & Automation Explorer configuration utility Wireless Sensor Network Ethernet Gateway The NI WSN-9791 Ethernet gateway coordinates communication between distributed NI WSN-32xx measurement nodes and a host controller in your NI wireless sensor network (WSN). The gateway uses a 2.4 GHz, IEEE radio to gather measurement data from the sensor network and a /0 Mbits/sEthernet port to provide flexible connectivity to a Windows PC or NI LabVIEW Real- Time PAC. With this flexibility, you can create simple, stand-alone wireless monitoring networks or completely integrated wired and wireless measurement solutions that feature access to the full breadth of NI hardware and software platforms. LabVIEW integration with NI WSNs delivers a common development environment for your applications as well as rapid application development, easy network configuration, remote data access, and the ability to program and customize measurement node behavior. The 9 to 30 VDC externally powered gateway offers -30 to 70 C operating temperatures, 50 g shock ratings, and a compact, 2U form factor. Up to 36 measurement nodes can communicate with a single gateway, and you can configure the Ethernet settings of the gateway for DHCP, static, and link-local IP address configurations. Wireless Networking The NI WSN system is built on a low-power, reliable IEEE network. The Ethernet gateway coordinates the wireless network, performing functions such as device authentication, message buffering, and network topology administration. The gateway, routers, and end nodes work together to form a mesh network. Measurement nodes can operate as routers or end nodes, providing the flexibility to extend the range of your sensor network. When nodes are configured as routers, they can repeat messages from end nodes and extend network range while acquiring measurement data. To save power and increase reliability, the network delivers a maximum theoretical throughput of 250 kbits/s. In general, this correlates to between 30 and 60 samples per minute per channel on the WSN measurement nodes. You can configure the network to operate on any of the 14 wireless communication channels to optimize performance and ensure coexistence with other wireless devices. The external, omnidirectional antenna and internal power amplifier offer up to 300 m outdoor range with line of sight. 460

7 Wireless Sensor Network Ethernet Gateway Software With NI-WSN software, you can easily configure your sensor network in the NI Measurement & Automation Explorer (MAX) configuration utility and quickly extract measurement data from your wireless sensor network with the LabVIEW graphical development environment. Network Configuration MAX offers an intuitive user interface to add and remove measurement nodes and configure wireless settings. Upon connection, the WSN-9791 Ethernet gateway is autodetected under Remote Systems in MAX, and you can assign measurement nodes to the gateway. The gateway maintains a list of nodes (by serial number) that have been authorized for network access. When a node powers up, it scans for available networks, locates either a gateway or router, and attempts to join it. If the gateway has the node in its list, the node joins the network, downloads the latest configuration from the gateway, and begins its normal operation of acquiring measurement data and controlling digital I/O. If a node is unable to connect, it executes a retry sequence with increasingly higher wait periods beginning with one minute between connect attempts and ending with 55 minutes between connect attempts. This preserves battery power if a gateway is offline. MAX also offers an overview of the nodes connected to your network including their last communication time, battery status, and link quality. In addition, MAX provides an interface to set the wireless communication channel, configure the gateway IP address, and wirelessly update firmware on the measurement nodes. Figure 2. NI WSN System in a LabVIEW Project Figure 1. Network Configuration in MAX Programming You can integrate your NI WSN measurement data directly into LabVIEW. After adding the WSN Ethernet gateway to a LabVIEW project, the nodes configured with the gateway in MAX are automatically added underneath the gateway in the project, giving you instant access to their I/O and properties. Simply drag and drop I/O variables from the LabVIEW project to a LabVIEW block diagram for data extraction, analysis, and presentation. Figure 3. Extracting NI WSN Measurement Data Using LabVIEW Wireless Sensor Network Ethernet Gateway 461

8 Wireless Sensor Network Ethernet Gateway Wireless Sensor Network Ethernet Gateway Advanced WSN Architectures You can combine NI WSNs with other NI platforms to customize and enhance your measurement capabilities. You can complement your NI WSN with PACs, vision systems, or even human machine interfaces (HMIs) to create a fully integrated solution that meets your unique application needs. LabVIEW integration with NI WSNs also provides database integration, remote data access with Web services, and customizable analysis and visualization of your data. In addition, you can use other NI software such as DIAdem to provide advanced data processing and analysis or the LabVIEW Datalogging and Supervisory Control Module for integrated event detection and alarming. Mechanical Information The WSN-9791 Ethernet gateway measures approximately 4.6 by 2.3 by 3.5 in. (L by W by H). The front of the gateway offers power, status, and activity LEDs in addition to a reset button that you can use to reboot the device. The power connector and Ethernet port are located on the front, while the DIN-rail and panel mount plate screw holes are located on the back of the device. The gateway also includes integrated panel mount holes that are located on the side of the device. Consult the WSN-9791 user guide for detailed mechanical information. Accessories NI WSN accessories feature options for gateway and measurement node mounting as well as a weatherproof enclosure for outdoor use of the measurement nodes. Available mounting accessories include options to panel mount and DIN-rail mount WSN measurement nodes and gateways. The NI WSN-3281 magnetic panel mount kit provides easy setup and takedown on virtually any metal surface. For high shock and vibration applications, NI recommends a panel mounting configuration rather than DIN-rail. NI WSN-3280 NI WSN-3281 NI WSN-3282 NI WSN-3283 Table 1. Mounting Kits NI WSN node panel mount bracket with spring-loaded screw-locking mechanism and integrated strain relief NI WSN node magnetic panel mount bracket with spring-loaded screw-locking mechanism and integrated strain relief NI WSN DIN-rail mounting kit for nodes or gateway (includes four screws) NI WSN panel mount plate for nodes or gateway (recommended for gateway) with additional four keyholes for mounting to wall in multiple orientations (includes four screws) You can choose from several power accessories that provide external power to the WSN Ethernet gateway or WSN measurement nodes. Desktop Power Supply This power supply provides 12 VDC power up to 1.25 A/15 W, and is rated for 0 to 70 C. The supply terminates with a 2-position MINI-COMBICON connector; plugs directly into the WSN gateway or measurement nodes. PS-5 Power Supply This DIN-rail-mountable, 24 VDC power supply delivers up to 5 A of current and is rated for operation from -25 to 60 C. Recommended for industrial installations. Table 2. External Power Supplies The connectivity accessories for NI WSN products include additional screw-terminal kits for the measurement nodes and a power connector backshell kit that contains a strain relief attachment for the two-position power connector on the Ethernet gateway and measurement nodes. Power Connectors Extra 2-position MINI-COMBICON power connectors quantity 4 Power Connector Strain relief attachment for the 2-position power connector on the Backshell measurement nodes and gateway that clips to the connector and includes a zip tie to hold the power cable in place Table 3. Connectivity Accessories Ordering Information NI WSN Starter Kit (Americas) NI WSN Starter Kit (Europe/Asia) Ethernet Gateway NI WSN-9791 (Americas) NI WSN-9791 (Europe/Asia) Programmable Measurement Nodes NI WSN-3202 (Americas) NI WSN-3202 (Europe/Asia) NI WSN-3212 (Americas) NI WSN-3212 (Europe/Asia) Nonprogrammable Measurement Nodes NI WSN-3202 (Americas) NI WSN-3202 (Europe/Asia) NI WSN-3212 (Americas) NI WSN-3212 (Europe/Asia) Power Accessories Desktop supply U.S. power cord PS-5 industrial supply Mounting Accessories NI WSN NI WSN NI WSN NI WSN Connectivity Accessories NI WSN NI WSN Power connectors Power connector backshell kit Outdoor Enclosure and Accessories NI WSN NI WSN NI WSN

9 Wireless Sensor Network Programmable Analog Input Measurement Nodes NI WSN-3202, NI WSN-3212 Programmable with the LabVIEW Wireless Sensor Network (WSN) Module Pioneer Extend battery life Increase sample rates Embed local decision making NI-WSN software provides easy network configuration and drag-and-drop LabVIEW programming Up to 3-year battery life 2.4 GHz, IEEE radio Outdoor range up to 300 m with line of sight Four analog input channels Four bidirectional digital channels (input, sinking output, or sourcing output) Industrial ratings: -40 to 70 C operating temperature 50 g shock, 5 g vibration Minimum Max DIO Analog Input Resolution Sample Internal Input DIO Voltage Sourcing Model Signal Type Channels (bits) (seconds) 1 Range(s) DIO Channels Range (V) (aggregate) Additional Features NI WSN-3202 Voltage ±, ±5, ±2, 4(sinking or 5 to 30 1 A 12 V, 20 ma sensor power output ±0.5V sourcing) NI WSN-3212 Thermocouple ±73 mv 4(sinking or 5 to ma Support for J, K, R, S, T, N, B, E sourcing) thermocouple types Table 1. WSN Node Specifications National Instruments wireless sensor networks (WSNs) deliver lowpower measurement nodes that offer industrial certifications, reliable networking, and optional weatherproof outdoor enclosures for long-term, remote deployments. The measurement nodes have direct sensor connectivity and a 2.4 GHz radio to wirelessly transmit data to the WSN Ethernet gateway. Each measurement node offers four analog input channels and four digital I/O channels that you can configure for input, sinking output, or sourcing output. You can customize the behavior of programmable NI WSN measurement nodes with the NI LabVIEW Wireless Sensor Network (WSN) Module Pioneer. Use this module to perform custom analysis, embed decision making on NI WSN measurement nodes, and extend battery life by optimizing node behavior. Power You can power the NI WSN measurement nodes with four 1.5 V AA alkaline battery cells, with operation up to three years on battery power at one sample per minute, or with a 9 to 30 V supply of external power. You can configure the four digital I/O channels for input, sinking output, or sourcing output. You must use an external power supply to provide sourcing output through the digital I/O channels, with a maximum total current output (aggregate on all channels) of 500 ma on the NI WSN-3212 and 1 A on the NI WSN The WSN-3202 also offers a 12 V, 20 ma sensor power output line that drives external sensors. Mesh Networking Gateways, routers, and end nodes work together to form a mesh network. Measurement nodes can operate as routers or end nodes, providing the flexibility to extend the range of your sensor network. When nodes are configured as routers, they can repeat messages from end nodes and extend network range while acquiring measurement data. Router nodes must remain on to send and receive data across the network, and should be powered with an external source such as a 9 to 30 V supply, solar panel, or larger battery. Wireless Sensor Network Programmable Analog Input Measurement Nodes 463

10 Wireless Sensor Network Programmable Analog Input Measurement Nodes Accessories NI WSN accessories feature options for gateway and measurement node mounting as well as a weatherproof enclosure for outdoor use of the measurement nodes. Available mounting accessories include options to panel mount and DIN-rail mount WSN measurement nodes and gateways. The NI WSN-3281 magnetic panel mount kit provides easy setup and takedown on virtually any metal surface. For high shock and vibration applications, NI recommends a panel mounting configuration rather than DIN-rail. NI WSN-3280 NI WSN-3281 NI WSN-3282 NI WSN-3283 Table 1. Mounting Kits NI WSN node panel mount bracket with spring-loaded screw-locking mechanism and integrated strain relief NI WSN node magnetic panel mount bracket with spring-loaded screw-locking mechanism and integrated strain relief NI WSN DIN-rail mount kit for nodes or gateway (includes four screws) NI WSN panel mount plate for nodes or gateway (recommended for gateway) with additional four keyholes for mounting to wall in multiple orientations (includes four screws) The NI WSN-3291 is an outdoor, weatherproof enclosure for NI WSN measurement nodes. The enclosure features two I/O glands for routing power or sensor cables and is shipped with four I/O gland inserts and two I/O gland plugs so you can customize the glands for your application. The WSN-3291 offers an IP64 (Ingress Protection) rating to protect NI WSN measurement nodes for longterm, outdoor deployment. You can choose from several power accessories that provide external power to the WSN Ethernet gateway or WSN measurement nodes. Desktop Power Supply PS-5 Power Supply Table 3. External Power Supplies The connectivity accessories for NI WSN products include additional screw- terminal kits for the measurement nodes and a power connector backshell kit that contains a strain relief attachment for the two-position power connector on the Ethernet gateway and measurement nodes. NI WSN-3284 Extra 18-position screw-terminal connectors for WSN top entry, 2 side entry with labels NI WSN-3285 Extra 18-position screw-terminal connectors for WSN top entry, 2 side entry with labels Power Connectors Extra 2-position MINI-COMBICON power connectors quantity 4 Power Connector Strain relief attachment for the 2-position power connector on the Backshell measurement nodes and gateway; clips to the connector and includes a zip tie to hold the power cable in place Table 4. Connectivity Accessories This power supply provides 12 VDC power up to 1.25 A /15 W, and is rated for 0 to 70 C. The supply terminates with a 2-position MINI- COMBICON connector that plugs directly into the WSN gateway or measurement nodes. This DIN-rail-mountable, 24 VDC power supply delivers up to 5 A of current and is rated for operation from -25 to 60 C. Recommended for industrial installations. Wireless Sensor Network Programmable Analog Input Measurement Nodes Figure 1. Outdoor Enclosure with NI WSN Measurement Node (not included) NI WSN-3291 IP64 outdoor enclosure for WSN measurement nodes NI WSN-3292 Set of replacement I/O glands: two glands, four inserts, two plugs NI WSN-3293 Additional I/O gland inserts (set of 5) Table 2. Outdoor Enclosure and Accessories 464