QuEChERS dspe EMR-Lipid, Part Number QuEChERS dspe EMR-Lipid, Part Number

Transcription

1 Conforms to US OSHA Hazard Communication 29CFR Section 1. Identification 1.1 Product identifier Product name Part No. Supplier/Manufacturer SAFETY DATA SHEET QuEChERS dspe EMR-Lipid, Part Number QuEChERS dspe EMR-Lipid, Part Number Validation date 6/3/ Relevant identified uses of the substance or mixture and uses advised against Material uses Analytical chemistry. Quantity 50 x 15 ml, 1 g / Tube Container type Polypropylene tube 1.3 Details of the supplier of the safety data sheet Agilent Technologies, Inc Stevens Creek Blvd Santa Clara, CA 95051, USA Emergency telephone number In case of emergency CHEMTREC Section 2. Hazards identification 2.1 Classification of the substance or mixture OSHA/HCS status Classification of the substance or mixture This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR ). H302 ACUTE TOXICITY (oral) - Category 4 H315 SKIN CORROSION/IRRITATION - Category 2 H319 SERIOUS EYE DAMAGE/ EYE IRRITATION - Category 2A H335 SPECIFIC TARGET ORGAN TOXICITY (SINGLE EXPOSURE) (Respiratory tract irritation) - Category GHS label elements Hazard pictograms Signal word Hazard statements Precautionary statements Prevention Warning H302 - Harmful if swallowed. H319 - Causes serious eye irritation. H315 - Causes skin irritation. H335 - May cause respiratory irritation. P280 - Wear protective gloves. Wear eye or face protection. P271 - Use only outdoors or in a well-ventilated area. P261 - Avoid breathing dust. P270 - Do not eat, drink or smoke when using this product. P264 - Wash hands thoroughly after handling. Date of issue 06/03/2015 1/10

2 Section 2. Hazards identification Response Storage Disposal 2.3 Other hazards Hazards not otherwise classified P304 + P340 + P312 - IF INHALED Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON CENTER or physician if you feel unwell. P301 + P312 + P330 - IF SWALLOWED Call a POISON CENTER or physician if you feel unwell. Rinse mouth. P302 + P352 + P P363 - IF ON SKIN Wash with plenty of soap and water. Take off contaminated clothing. Wash contaminated clothing before reuse. P332 + P313 - If skin irritation occurs Get medical attention. P305 + P351 + P338 - IF IN EYES Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P337 + P313 - If eye irritation persists Get medical attention. P405 - Store locked up. P501 - Dispose of contents and container in accordance with all local, regional, national and international regulations. None known. Section 3. Composition/information on ingredients Substance/mixture Mixture Ingredient name % CAS number Diisocyanate-Polyol Copolymer Any concentration shown as a range is to protect confidentiality or is due to batch variation. There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section. Occupational exposure limits, if available, are listed in Section 8. Section 4. First aid measures 4.1 Description of necessary first aid measures Eye contact Inhalation Skin contact Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention. If necessary, call a poison center or physician. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Continue to rinse for at least 10 minutes. Get medical attention. Wash clothing before reuse. Clean shoes thoroughly before reuse. Date of issue 06/03/2015 2/10

3 Section 4. First aid measures Ingestion Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention. If necessary, call a poison center or physician. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. 4.2 Most important symptoms/effects, acute and delayed Potential acute health effects Eye contact Inhalation Skin contact Ingestion Over-exposure signs/symptoms Eye contact Inhalation Skin contact Ingestion May cause respiratory irritation. Causes skin irritation. Causes serious eye irritation. Harmful if swallowed. Adverse symptoms may include the following pain or irritation watering redness Adverse symptoms may include the following respiratory tract irritation coughing Adverse symptoms may include the following irritation redness No specific data. 4.3 Indication of immediate medical attention and special treatment needed, if necessary Notes to physician Specific treatments Protection of first-aiders In case of inhalation of decomposition products in a fire, symptoms may be delayed. The exposed person may need to be kept under medical surveillance for 48 hours. No specific treatment. No action shall be taken involving any personal risk or without suitable training. If it is suspected that fumes are still present, the rescuer should wear an appropriate mask or self-contained breathing apparatus. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. See toxicological information (Section 11) Section 5. Fire-fighting measures 5.1 Extinguishing media Suitable extinguishing media Unsuitable extinguishing media Use an extinguishing agent suitable for the surrounding fire. None known. 5.2 Special hazards arising from the substance or mixture Specific hazards arising from the chemical No specific fire or explosion hazard. Date of issue 06/03/2015 3/10

4 Section 5. Fire-fighting measures Hazardous thermal decomposition products Decomposition products may include the following materials carbon dioxide carbon monoxide nitrogen oxides 5.3 Advice for firefighters Special protective actions for fire-fighters Special protective equipment for fire-fighters Section 6. Accidental release measures Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. 6.1 Personal precautions, protective equipment and emergency procedures For non-emergency personnel For emergency responders No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For nonemergency personnel". 6.2 Environmental precautions Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). 6.3 Methods and materials for containment and cleaning up Move containers from spill area. Avoid dust generation. Using a vacuum with HEPA filter will reduce dust dispersal. Place spilled material in a designated, labeled waste container. Dispose of via a licensed waste disposal contractor. Section 7. Handling and storage 7.1 Precautions for safe handling Protective measures Advice on general occupational hygiene Put on appropriate personal protective equipment (see Section 8). Do not ingest. Avoid contact with eyes, skin and clothing. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. 7.2 Conditions for safe storage, including any incompatibilities Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Store locked up. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. 7.3 Specific end use(s) Date of issue 06/03/2015 4/10

5 Section 7. Handling and storage Recommendations Industrial sector specific solutions Industrial applications, Professional applications. Not applicable. Section 8. Exposure controls/personal protection 8.1 Control parameters Occupational exposure limits None. 8.2 Exposure controls Appropriate engineering controls Environmental exposure controls Use only with adequate ventilation. If user operations generate dust, fumes, gas, vapor or mist, use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. Individual protection measures Hygiene measures Eye/face protection Skin protection Hand protection Body protection Other skin protection Respiratory protection Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection chemical splash goggles. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Use a properly fitted, particulate filter respirator complying with an approved standard if a risk assessment indicates this is necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator. Date of issue 06/03/2015 5/10

6 Section 9. Physical and chemical properties 9.1 Information on basic physical and chemical properties Appearance Physical state Color Odor Odor threshold ph Melting point Boiling point Flash point Evaporation rate Flammability (solid, gas) Lower and upper explosive (flammable) limits Vapor pressure Vapor density Relative density Solubility Partition coefficient n- octanol/water Auto-ignition temperature Decomposition temperature Viscosity Solid. White. Off-white. Section 10. Stability and reactivity 10.1 Reactivity No specific test data related to reactivity available for this product or its ingredients Chemical stability The product is stable Possibility of hazardous reactions Under normal conditions of storage and use, hazardous reactions will not occur Conditions to avoid No specific data Incompatible materials May react or be incompatible with oxidizing materials Hazardous decomposition products Section 11. Toxicological information 11.1 Information on toxicological effects Acute toxicity Irritation/Corrosion Sensitization Under normal conditions of storage and use, hazardous decomposition products should not be produced. Date of issue 06/03/2015 6/10

7 Section 11. Toxicological information Mutagenicity Carcinogenicity Reproductive toxicity Teratogenicity Specific target organ toxicity (single exposure) Name Diisocyanate-Polyol Copolymer Category 3 Not applicable. Respiratory tract irritation Specific target organ toxicity (repeated exposure) Aspiration hazard Category Route of exposure Target organs Information on the likely routes of exposure Potential acute health effects Eye contact Inhalation Skin contact Ingestion Routes of entry anticipated Oral, Dermal, Inhalation. Causes serious eye irritation. May cause respiratory irritation. Causes skin irritation. Harmful if swallowed. Symptoms related to the physical, chemical and toxicological characteristics Eye contact Inhalation Skin contact Ingestion Adverse symptoms may include the following pain or irritation watering redness Adverse symptoms may include the following respiratory tract irritation coughing Adverse symptoms may include the following irritation redness No specific data. Delayed and immediate effects and also chronic effects from short and long term exposure Short term exposure Potential immediate effects Potential delayed effects Date of issue 06/03/2015 7/10

8 Section 11. Toxicological information Long term exposure Potential immediate effects Potential delayed effects Potential chronic health effects General Carcinogenicity Mutagenicity Teratogenicity Developmental effects Fertility effects No known significant effects or critical hazards. No known significant effects or critical hazards. No known significant effects or critical hazards. No known significant effects or critical hazards. No known significant effects or critical hazards. No known significant effects or critical hazards. Numerical measures of toxicity Acute toxicity estimates Route Oral Dermal ATE value mg/kg mg/kg Section 12. Ecological information 12.1 Toxicity 12.2 Persistence and degradability 12.3 Bioaccumulative potential 12.4 Mobility in soil Soil/water partition coefficient (KOC) 12.5 Other adverse effects No known significant effects or critical hazards. Section 13. Disposal considerations 13.1 Waste treatment methods Disposal methods The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been Date of issue 06/03/2015 8/10

9 Section 13. Disposal considerations cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Disposal should be in accordance with applicable regional, national and local laws and regulations. Local regulations may be more stringent than regional or national requirements. The information presented below only applies to the material as supplied. The identification based on characteristic(s) or listing may not apply if the material has been used or otherwise contaminated. It is the responsibility of the waste generator to determine the toxicity and physical properties of the material generated to determine the proper waste identification and disposal methods in compliance with applicable regulations. Refer to Section 7 HANDLING AND STORAGE and Section 8 EXPOSURE CONTROLS/PERSONAL PROTECTION for additional handling information and protection of employees. Section 14. Transport information Regulatory information DOT / IMDG / IATA Not regulated. Section 15. Regulatory information 15.1 Safety, health and environmental regulations/legislation specific for the substance or mixture U.S. Federal regulations United States inventory (TSCA 8b) All components are listed or exempted. Clean Air Act Section 112 (b) Hazardous Air Pollutants (HAPs) Clean Air Act Section 602 Class I Substances Clean Air Act Section 602 Class II Substances DEA List I Chemicals (Precursor Chemicals) DEA List II Chemicals (Essential Chemicals) SARA 302/304 Not listed Not listed Not listed Not listed Not listed Composition/information on ingredients No products were found. SARA 304 RQ SARA 311/312 Classification Not applicable. Composition/information on ingredients Immediate (acute) health hazard Name % Fire hazard Sudden release of pressure Reactive Immediate (acute) health hazard Diisocyanate-Polyol Copolymer No. No. No. Yes. No. Delayed (chronic) health hazard State regulations Massachusetts New York None of the components are listed. None of the components are listed. Date of issue 06/03/2015 9/10

10 Section 15. Regulatory information New Jersey Pennsylvania California Prop. 65 No products were found. Canada inventory International regulations International lists Chemical Weapons Convention List Schedule I Chemicals Chemical Weapons Convention List Schedule II Chemicals Chemical Weapons Convention List Schedule III Chemicals None of the components are listed. None of the components are listed. Not determined. Australia inventory (AICS) Not determined. China inventory (IECSC) Not determined. Japan inventory All components are listed or exempted. Korea inventory Not determined. Malaysia Inventory (EHS Register) Not determined. New Zealand Inventory of Chemicals (NZIoC) Not determined. Philippines inventory (PICCS) Not determined. Taiwan inventory (CSNN) Not determined. Not listed Not listed Not listed Section 16. Other information History Date of issue Date of previous issue Version 6/3/2015. No previous validation 1 Indicates information that has changed from previously issued version. Notice to reader Disclaimer The information contained in this document is based on Agilent s state of knowledge at the time of preparation. No warranty as to its accurateness, completeness or suitability for a particular purpose is expressed or implied. Date of issue 06/03/ /10