ATEX GOST. Fire Alarm Call Points, Hazardous Location BG and PB

Transcription

1 Fire Alarm Call Points, Hazardous Location BG and PB Description: These manual fire alarm call points have been designed for use in hazardous locations and harsh environmental conditions. The GRP enclosures are suitable for use offshore or onshore, where light weight combined with a high level of corrosion resistance is required. Features: ATEX approved UL Listed for USA and Canada Hazardous locations: Class I, Div 2, Groups A-D Class II, Div 2, Groups F & G Class I, Zones 1 & 2, AExd IIC T4 Ordinary locations: Audible-Signal Device CSA Certified NEMA 4x &6, IP66 and IP67 Certified temperature 13 F to +131 F ( 25 C to +55 C) Corrosion resistant GRP Plastic break glass element available Retained stainless steel cover screws Optional lift flap Key operated test facility on BG Architects and Engineers Specifications Fire alarm call points and push buttons for hazardous locations and harsh environments shall be UL Listed for Class I, Division2, Groups A,B,C&D, and Class I, Zone 1&2 applications. They shall be constructed of lightweight, UV stable glass reinforced polyester, shall be corrosion resistant, and shall meet NEMA 4x, NEMA 6, IP 66 & IP 67 environmental requirements over a temperature range of -13 F to +131 F (-25 C to +55 C). Actuation of the call point or push button shall require the opening of a flap and depression of an actuator. An actuated unit shall remain latched until reset. A reset operation shall only take place through the use of a key. ATEX GOST

2 Specification Certification: Voltage: Up to 240V. Certified temp: Configuration Options: UL Listed for USA and Canada Hazardous locations: Class I, Div 2, Groups A-D. Class II, Div 2, Groups F & G. Class I Zones 1 & 2, AExd IIC T4. Listing No: E Ordinary locations: Audible-Signal Device. Listing No. S8117. CSA Certified to C22.2 (PB only), Nos. 0-M, 0.4M, 14-M, 25,30-M, 94, 142-M 1987, 157M 1987, , Enclosure Type 4, 4A, Class 1, Groups A-D, Cert. No ATEX Approved: EN50014, EN50018, EN50019, EN Cert. No. BAS02ATEX2105X (BG & PB), EExed II C T6 (switch only), EExedm IIC T4 (other versions). Zones 1 and 2. BGUL: 13 F to +131 F ( 25 C to + 55 C); PBUL: 13 F t+131 F ( 25 C to +55 C). PB (CSA): -58 F to +104 F (- 50 C to +40 C). Ingress Protection: NEMA 4x & 6, IP66 & 67. Terminals: 6 x 14 AWG standard (BGUL), 7 or 9 x 14 AWG standard. Switch Rating (1 or 2 changeover switches fitted): Max Rating 240VAC, 3A. Cable Entries: Weight: Material: Model Certification Entries Labels Switches Features Terminals Finish Finish: Resistors: Up to 4 entries 1 2 NPT. 2.6 lb/1.2kg (Varies with model & entries). Glass reinforced polyester. Red epoxy painted finish as standard or to Customer s specification. Various configurations available on versions up to 24V, 470R minimum. LED Indication: A high intensity red LED can be fitted as an optional extra to indicate operation on versions up to 24V. Labelling: BG Glass label reads either (1) Fire Break glass press here. (2) Break glass press here. (3) Worded to Client s requirements. PB & BG Duty label worded to Client s requirements. Riveted on. PB & BG Tag label worded to Client s requirements. Screwed on. Model BG PB Entries Certification CSA Exi (PBI only) UL Class I, Div. 2 UL - Ordinary locations Standard Models 1 /2" NPT *C *Prefix entry size (see diagram above) with entry position code e.g. 1A, 2A. IC UL UW Labels None 0 Glass label (1) reqd. 1 Glass label (2) reqd. 2 Glass label (3) reqd. 3 Duty label reqd. 4 Tag label reqd. 5 Specify wording on 3, 4 or 5 as required. Series Model Number Order Decription Switches PB PBUL4C6C4DSN7R Push button, Fire label, Red finish Features Single changeover *S Double changeover *D *Prefix with voltage A for A.C. D for D.C. except for BGI. None N LED A Lift Flap (BG only) B Resistor Series *C Resistor EOL *D Break glass P *Specify values Finish Red (Standard) R Natural Black N Blue B Yellow Y Grey G Yellow/Black Stripes X Other specify S Terminals *BGUL only *6 x 14 AWG (standard) 6 7 x 14 AWG (standard) 7 9 x 14 AWG (optional) Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA BG and PB 08/06

3 Strobe/Sounder Combination Units, Heavy Duty Industrial and Marine, Weatherproof Description: This range of audio/visual combination units may be assembled from a range of strobes and horns. Mounted on a sturdy, drilled, painted, stainless steel plate, the units are pre-wired as standard such that a single input operates both the sounder and strobe simultaneously. Units are available for use in potentially explosive atmospheres and dedicated units are now available for use in industrial and marine environments. Example of installed combination unit Features*: Zones 1, 2 and safe area use ATEX approved Ex II 2GD UL listed Class I, Div. 1 & 2, Groups C & D IP66 and 67 Certified temperature 67 F to +158 F ( 55 C to +70 C) Corrosion free GRP strobe/sounder Strobe available as xenon, filament, fluorescent or LED Xenon: up to 21J Filament: up to 100W Fluorescent: up to 39W LED: up to 192cd Sounder: up to 115dBA output at 1 metre All stainless steel (316), epoxy painted back plate *Model dependent. XB11/DB3 Example shown is for illustration only. Other combinations are available. Architects and Engineers Specifications Horn/Strobe Combination units Horns and strobes for hazardous locations and harsh environments shall be factory assembled in combination on a stainless steel mounting plate and shall be factory wired for simultaneous operation of the horn and strobe from a single input. Speaker/Strobe Combination units Speakers and strobes for hazardous locations and harsh environments shall be factory assembled in combination on a stainless steel mounting plate with separate inputs provided for the speaker and the strobe. Note: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Cooper Wheelock standard terms and conditions. ATEX

4 Configuration Options: 1. XB11/DB3 or XB11/DB4 Explosionproof Xenon 5J; Sounder up to 115dB(A), all GRP corrosion free products. Certification: ATEX: Ex II 2GD, EExdIIBT5. UL: Class I, Div. 2, Groups C & D. Voltage: 24V d.c.,110v a.c., 240V a.c. Strobe: Standard: XB11 (Xenon 5J). Option: Filament (10W). Fluorescent ( 10W). Sounder: Standard: DB3 (long flare) 115dBA at 1 metre. Option: DB3 (short flare) 108dBA at 1 metre. Dimensions (mm): 420 (height) x 220 (width) x 337 (depth). Options: Refer to data sheet. Specify when ordering. Ordering information Specify options 1 to 4 Product 1. Certification 2. Voltage 3. Lens color 4. Finish XB11+DB3 + ATEX UL + see above + Red Amber + Natural Black Red or XB11+DB4 2. SM87HXB/DB1 Explosionproof Xenon 5J; Sounder up to 110dB(A), LM25 or stainless steel construction, red finish. Certification: ATEX: Ex II 2G, EExdIIBT4(T3). UL: Class I, Div. 1, Groups C & D. Voltage: 24V d.c.,110v a.c., 240V a.c. Strobe: Standard: SM87 (Xenon 5J). Option: Filament (10W). Fluorescent ( 10W). LED ( 192cd) Sounder: Standard: DB1 HP 110dB(A) at 1 metre. Option: DB1 P 106dB(A) at 1 metre. Dimensions (mm): 351 (height) x 228 (width) x 205 (depth). Options: Refer to data sheet. Specify when ordering. Note: Example only actual arrangement may vary (contact sales office) Ordering information Specify options 1 to 5 Product 1. Body Material 2. Certification 3. Voltage 4. Lens color 5. Finish SM87HXB+DB1HP + LM25 stainless steel + ATEX UL + see above + Red Amber + specify Ordering information Specify options 1 to 5 Product 1. Body Material 2. Certification 3. Voltage 4. Lens color 5. Finish SM87HXB+DB3 + LM25 stainless steel + ATEX UL + see above + Red Amber + specify 3. XB13/DB12 or XB13/DB15 Heavy Duty Industrial & Marine Xenon 10J; Sounder DB12 (DB15) up to 110dB(A) (117 db(a)) Applications: Voltage: Strobe: Sounder: Harsh Industrial & Marine Environments. 12V, 24V d.c., 110V, 240V a.c. Standard: XB13 (Xenon 10J). Standard: DB12 110dB(A) at 1 metre. Standard: DB15 115dB(A) at 1 metre. Dimensions (mm): 300 (height) x 195 (width) x 220 (depth). Ordering information Specify options 1 to 3 Product 1. Voltage 2. Lens color 3. Finish XB13/DB12 + see above + Red Amber + Natural Red Standard Models Series Model Number Order Decription XB11/DB3 XB11DB3UL24CR Multitone/Strobe, Clear lens, Red finish XB11/DB4 XB11DB4UL25CR Speaker/Strobe, Clear lens, Red finish XB11/DB3 XB11DB3UL24RR Multitone/Strobe, Red lens, Red finish XB11/DB4 XB11DB4UL25RR Speaker/Strobe, Red lens, Red finish Other combinations of strobes and sounders are available please contact sales office for detailed specifications. 273 Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA Combo Units 08/06

5 Horn - 103dB, Explosion Proof, High Output DB1 Description: This range of light weight, flameproof horns has been designed with a high weatherproof rating to cope with the harsh environmental conditions found offshore and onshore in the oil, gas and petrochemical industries. New electronic circuitry allows the DB1P and DB1HP to be switched between two selectable tones by either reversing the supply polarity, or connecting a second voltage supply. The higher output are particularly suitable for noisy environments. Features*: UL Listed Class I, Div 1. Groups C & D Class I, Zone 1 and Zone 2 use ATEX approved NEMA 4x, IP66 Certified temperature 13 F to +158 F ( 25 C to +70 C) NFPA 72 compliant 4 wire diode monitored connection for operation in supervisory mode Up to 103 dba 10 feet Marine grade alloy Up to 27 output tones, user selectable 12V, 24V & 48 VDC, 110 VAC Tones can be selected remotely Any two tones may be switched via the external voltage supply *Depends on version Architects and Engineers Specifications Explosion-proof horns shall be UL Listed for Class I, Division 1, Groups C&D, and Class I, Zone 1 hazardous locations. The horns shall be constructed of marine grade alloy with an epoxy paint finish and shall meet NEMA 4x and IP 66 environmental requirements over a temperature range of -13 F to 158 F (-25 C to 70 C) in hazardous and harsh environments. The horns shall have 27 user selectable output tones. Multiple horns shall be able to operate in synchronization. Rated current draw at 24 vdc shall not exceed 250 ma for rated sound output of 93 dba at 10 feet or 700 ma for rated sound output of 100 dba at 10 feet. The horns shall be capable of direct surface mounting. Note: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Cooper Wheelock standard terms and conditions. ATEX

6 NOTE:- DB1H(P) DIMENSIONS IN BRACKETS Specification Certification: UL Listing: Class I, Div 1, Groups C & D. Listing No. E ATEX approved: EExd, IIB T3 Cert No. Baseeta 02ETEX0207 for DB(1P) Cert No. Baseeta 02ETEX0209 for DBH(P) Material: Finish: Max Sound Levels: Weight: LM25 corrosion resistant alloy or ANC4B stainless steel with stainless steel cover screws. ABS flare. Epoxy paint finish as standard or to customer's specification. DB1(P)=93±3dB(A) (86±3dB(A) for 12V DB1). DB1H(P)=100 ± 10 feet Note: Sound level is dependent upon the tone selection. DB1P 7.7lb./3.5 Kg approx. DB1HP 12.3lb./5.6 Kg approx. Certified Temperature: 13 F to +158 F ( 25 C to +70 C) Ingress Protection: NEMA 4x, IP66. Tone Selection: 27 User Selectable Tones 1 Alt Tones 800/970 Hz at 1/4 sec Hz for 0.1S/440 Hz for 0.1S 2 Sweeping 800/970 Hz at 7 Hz 16 Int 660 Hz 150 ms on 150 ms off 3 Sweeping 800/970 Hz at 1 Hz 17 Int 660 Hz 1.8 sec. on 1.8 sec. off 4 Continuous at 2850 Hz 18 Int 660 Hz 6.5 sec. on 13 sec. off 5 Sweeping Hz at 7 Hz 19 Continuous 660 Hz 6 Sweeping Hz at 1 Hz 20 Alt 554/440 Hz at 1 Hz 7 Slow Whoop 21 Int 660 Hz at 7/8 Hz 8 Sweep Hz at 1 Hz 22 Int 2850 Hz 150 ms on 100 ms off 9 Alt Tones 2400/2850 Hz at 2 Hz 23 Sweep Hz at 50 Hz 10 Int Tones of 970 Hz at 1 Hz 24 Sweep Hz at 50 Hz 11 Alt Tones 800/970 Hz at 7/8 Hz 25 3x970 Hz pulses 0.5 off, 1.5 off 12 Int Tone at 2850 Hz at 1 Hz 26 3x2850z pulses 0.5 on/0.5 off, 1.5 off Hz at 1/4 sec. on 1 sec. off 27 Int 3100 Hz 0.3 sec. on 0.7 sec. off 14 Continuous at 970 Hz Current Consumption: DB1(P) DB1H(P) 12V 125mA 900mA 24V 250mA 700mA 48V 250mA 110V 60mA 200mA Labels: Entries: Terminals: Duty and tag labels optional. Up to 3 x 1/2" or 3/4" NPT Suitable to accept up to 12AWG conductor size Configuration Options: The following code is designed to help in the selection of the correct unit. Build up the reference number by inserting the code for each component into the appropriate box. Single Stage - 4 wire diode monitored connection - on board diode allows unit to be operated in supervisory mode when monitoring line in reverse polarity Two Stage - Switchable unit available in DC versions only either by: (i) Reversing the polarity of the supply, or, (ii) By a 3 wire common +ve system, switching between the -ve lines Unit Type Voltage Cable Entries Duty Labels Tag Label Features Finish DB1P ULA DB1HP ULA Voltage 12V d.c V d.c V d.c. DB1(P) only V a.c V a.c. 240 Entries 1 /2" NPT C 3 /4" NPT D LHS 1 RHS 2 Bottom 3 *Prefix position with entry size code e.g. C1C3 = 20mm left and bottom entries. Standard Models Series Model Number Order Decription DB1 DB1PULA024D1D2NNNR Multitone, 93dBA, 24 VDC, Red finish DB1 DB1HPULA024D1D2NNNR Multitone, 100dBA, 24 VDC, Red finish Duty Labels None Required* *(Please specify) Tag N D None Required *Please specify Label N T Finish Red Grey Special Features Not required Yes* *Please specify R G S N Y 273 Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA DB1 08/06

7 Horns - Up to 108dB(A), Hazardous Location, Weatherproof DB3 Range Sounder/Strobe Combination Unit Description: This range of light weight all GRP, explosionprrof horns is intended for use in potentially explosive atmospheres and has been designed with high ingress protection to cope with the harsh environmental conditions found offshore and onshore in the oil, gas and petrochemical industries. The flamepaths, flare and the body, are manufactured completely from a UV stable glass reinforced polyester. Stainless steel screws and sinter are incorporated thus ensuring a corrosion free product. A tapered flamepath is used to overcome the problems of assembly of parallel spigot flamepaths. An optional Exe terminal chamber is available. Features*: UL Listed for USA and Canada Hazardous locations: Class I, Div 2, Groups A, B, C & D Class II, Div 2, Groups F & G Class I, Zones 1 & 2, AExd IIC T4 Ordinary locations: Audible-Signal Device ATEX approved NEMA 4x &6, IP66 and IP67 Certified temperature 67 F to +158 F ( 25 C to +70 C) All GRP corrosion free flamepaths Up to 108dBA output at 10 feet Integral volume control 27 tones, user selectable Two tones may be switched via the external voltage supply Horn/Strobe Combination Unit available *Depends on version Architects and Engineers Specifications Horns for hazardous locations and harsh environments shall be UL and cul listed for Class I, Division 2, Groups A,B,C&D, and Class I, Zones 1&2, AExd IIC T4 applications and shall be listed under UL Standard 1638 for Indoor/Outdoor use. They shall be constructed of lightweight, UV stable glass reinforced polyester, shall be corrosion resistant, and shall meet NEMA 4x, NEMA 6, IP 66 & IP 67 environmental requirements over a temperature range of -67 F to +158 F (-55 C to +70 C). The horns shall have 27 user selectable output tones. Multiple horns shall be able to operate in synchronization. Rated current draw at 24 vdc shall not exceed 380 ma for rated sound output of 105 dba at 10 feet. The horns shall include an integral volume control and a stainless steel mounting bracket with ratchet facility to direct sound output. Note: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Cooper Wheelock standard terms and conditions. ATEX

8 Terminals: Mounting: Labels: Cable Entries: Tone Selection: Horn/Strobe Unit: Two Stage Unit DB3P: D.C. A.C. 4 x 14 AWG, 6 x 14 AWG Stainless steel bracket with ratchet facility. Duty and tag labels optional. Up to 2 x 1 /2" NPT UL. 27 user selectable tones. The DB3 may be combined with a strobe to create a combined audio/visual alarm. Switchable between two tones: (i) Reversing the polarity of the supply, or (ii) by a 3 wire common +ve system, switching between the two ve lines. (iii) Closing/opening connection between 2 terminals e.g. by using a volt free relay contact at the panel. 2 tones must be specified at time of order. 3/4 Tone Unit: Remote 3 or 4 tone available contact sales office for details. Specification Certification: Material: Finish: UL Listed for USA and Canada Hazardous locations: Class I, Div 2, Groups A, B, C & D Class II, Div 2, Groups F & G. Class I Zones 1 & 2, AExd IIC T4. UL Listing No: E Ordinary locations: Audible-Signal Device. Listing No. S8116. ATEX Approved: CENELEC EN50014, 18, 19 Cert. No. BAS00ATEX2097X, EExd IIC. Cert. No. BAS00ATEX2098X, EExde IIC. Zones 1 and 2. Body & horn in anti-static, UV stable, glass reinforced polyester. Swivel bracket & captive cover screws in stainless steel. Body and horn, natural black or epoxy paint coated to client s color requirements Sound Output: DB3 105 ± 3dB(A) at 10 feet (tone dependent) Volume Control: *Nominal Output (dba) Input Current (ma) *Output measured with 24V input voltage. Tone set to 970Hz continuous. Weight: Certified Temperature: Ingress Protection: Voltage: Current Consumption: 13.2lb./6.0kg approx. 67 F to +158 F ( 55 C to +70 C) NEMA 4x & 6, IP66 and IP67 Up to 48V d.c. Up to 254V a.c. V 12VDC 24VDC 48VDC 110VAC 120VAC 220VAC 230VAC 240VAC 254VAC I 760mA 380mA 190mA 135mA 124mA 68mA 65mA 62mA 59mA Configuration Options: The following code is designed to help in selection of the correct unit. Build up the reference number by inserting the code for each component into the appropriate box. Other Unit Type Certification Voltage Labels Entries Options Finish Certified Plugs Type DB3 DB3P Standard Models Series Model Number Order Decription DB3 DB3 Details Standard unit Two stage Type UL Listed UL (Ordinary Locations) UL UW Voltage 12V - 48V d.c V a.c V a.c V a.c V a.c V a.c V a.c. 254 DB3UL048N2CNRZ Multitone, 108 dba, 24 VDC, Red finish, plugs DB3UL110N2CNRZ Multitone, 108 dba, 110 VAC, Red finish, plugs Label Duty D* Tag T* None N *Please specify wording Entries Features 1 x 1 /2" NPT 1C 2 x 1 /2" NPT 2C Colour None N End of line resistor E* *State value. Natural Black N Red R Special S* *Please specify Certified Plugs Plugs *Z *must always be indicated with a Z. If no plugs are required omit the "Z" from the order code 273 Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA DB3 02/07

9 Speakers - Up to 25 Watts, Hazardous Location, Weatherproof DB4 Range 15W/20W/25W (Long Flare) 8W (Short Flare) Description: This range of loudspeakers, intended for use in potentially explosive gas and dust atmospheres, has a power rating of up to 25 watts and is suitable for use in all gas groups including hydrogen. The flamepaths, flare and the body, are manufactured completely from a UV stable glass reinforced polyester. Stainless steel screws and sinter are incorporated thus ensuring a corrosion free product. A tapered flamepath is used to overcome the problems of assembly of parallel spigot flamepaths. This product does not include a blocking capacitor. Contact Cooper Wheelock Technical Support for models with a blocking capacitor*. *Coming Soon Features*: UL listed for USA and Canada: Class I, Div 2, Groups A-D. Class I, Zones 1, AExd IIC, T4 Class II, Div 2, Groups F & G ATEX approved NEMA 4x & 6, IP66 and IP67 Certified temperature 67 F to +158 F (-55 C to +70 C) GRP corrosion-free flamepaths 109dBA at 25 watts at 10 feet 8, 15 and 25 watt versions Power tappings, via integral transformer Ratcheted swivel bracket Stainless steel sinter Stainless steel mounting bracket Tapered flamepath *Depends on version Architects and Engineers Specifications Speakers for hazardous locations and harsh environments shall be UL and cul listed for Class I, Division 2, Groups A,B,C&D, and Class I, Zones 1, AExd IIC T4 applications. They shall be constructed of lightweight, UV stable glass reinforced polyester, shall be corrosion resistant, and shall meet NEMA 4x, NEMA 6, IP 66 & IP 67 environmental requirements over a temperature range of -67 F to +158 F (-55 C to +70 C). The speakers shall be rated for 70 vrms input with power taps for 1,2,4,6,12.5 or 25 watt operation. Rated sound output shall be up to 109 dba at 10 feet and rated frequency response shall be 400Hz to 8kHz. The speakers shall include a stainless steel mounting bracket with ratchet facility to direct sound output. Note: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Cooper Wheelock standard terms and conditions. ATEX

10 Polar plot (1W/1m) for 25 watt version. Specification Rated Power: Certification: Material: Finish: Output: Weight: Certified Temperature: Ingress Protection: Frequency Range: Voice Coil Impedence: Transformer: 8, 15 or 25 watts RMS continuous (at 77 F). UL listed for USA and Canada: Class I, Div 2, Groups A-D Class I, Zones 1, AExd IIC T4. Class II, Div 2, Groups F & G ATEX approved: EN50014, 18, 19. No. BAS00ATEX2097X. EExd 11C T41/T5 Cert. No. BAS00ATEX2098X. EExd 11C T41/T5 Zones 1 not for use in atmospheres containing carbon disulphide Body & horn in anti-static, UV stable, glass reinforced polyester. Swivel bracket in stainless steel. Captive cover screws in stainless steel. Body and horn, natural black or epoxy paint coated to client s color requirements. 97 dba at 1 Watt at 10 feet 109 dba at 25 Watts at 10 feet Measured in accordance with IEC lb./5.0kg approx. 67 F to +158 F (55 C to +70 C) NEMA 4x & 6, IP66 & IP Hz to 8kHz. 8 ohms. Used to vary the rated power by selecting different tappings (see table below). Transformer Power Tappings 25W 15W 8W 1:2 25.0* 15.0* 8.0* 2:3 12.5* 7.5* 4.0* 3: : :4 2.0* 2.0* 0.7* Transformer Tappings 1: Transformer Options: i) Standard Tapping: (4 x 2) terminal tap change (8 terminals). ii) Optional Tapping: 4 terminal tap change with 2 terminals (5 & 6), directly connected to driver (8 ohms). Other tappings & driver impedances available on request. Terminals: Mounting: Labels: Cable Entries: 8 x 14AWG Bracket with ratchet facility. Duty and tag labels optional. 2 x 1 /2" NPT. *Include blocking capacitor for DC supervision of field wiring Polar plot and frequency response curves for other speakers are available upon request. Configuration Options: Max. Rated Power Certification Transformer Labels Entries Color DB4 UL Power 8 watt 8 15 watt watt 25 Standard Models Type UL listed UL Series Model Number Order Decription DB4 DB4 Transformer Yes X* None N *Std 100V Other values available, specify voltage. DB425ULXN2CR Speaker, 25 Watt, Transformer, Red Finish DB415ULXN2CR Speaker, 15 Watt, Transformer, Red Finish Label Duty D* Tag T* None N *Please specify wording Color Natural Black N Red R Special S* *Please specify Entries 1 x ½" NPT 1C 2 x ½" NPT 2C To specify certified plug, suffix appropriate code with 'P'. e.g. 2CP is 2 x 1/2" NPT entries with one certified plug 273 Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA DB4 04/07

11 Series MAX Strobes: Amber, Blue, Clear, Red Description: The AC-MAX and AC-MAXS models are for 120 VAC applications. The DC-MAX and DC-MAXS models are for DC applications, with a DC voltage range of 10.5 VDC to 31.0 VDC. MAXS versions offer two steady lights in addition to the strobe light. SERIES MAX STROBE High Intensity, weather-resistant visible warning signal, designed for stationary or mobile applications. Available in AC or DC voltage and with steady light option. Features for all Models: Approvals include: UL Standard 1638 Listed for indoor or outdoor use AC-MAX and AC-MAXS mdels are for 120 VAC applications Powerful double flash light burst 60 double flashes per minute Available lens colors per SAE specifications: Amber, Blue, Clear, Red Durable, high impact Lexan construction Mounting options: 1/2 inch pipe, surface mount, flange mount, standard 4-inch square electrical box or Wheelock WBB Weather Resistant Backbox (order code 2959) Overall height: 5 inches Diameter: 6.2 inches Weight: 2 lbs. Applications for Series MAX Strobes: Hazard warning/alerting Industrial visual signaling Strobe beacons for vehicles or equipment Process control area notification Access gate/loading dock identification Features for Steady Light Models: Two 7 watt incandescent lamps Independent wiring for electrical hook-up Applications for Strobe & Steady Light Models: Location of specific equipment Eye wash station/emergency medical kit location Emergency phone location Warning lights Security alert indication NOTE: The Series MAX Strobes are not designed to operate on a synchronized NAC Circuit. U L S5391

12 Architects and Engineers Specifications Industrial Strobes shall be Wheelock Series MAX Strobes; AC-MAX, AC-MAXS, DC-MAX, DC-MAXS. Wheelock Series MAX Strobes; AC-MAX, AC-MAXS, DC-MAX, DC-MAXS shall be UL Standard 1638 Listed. Series MAX AC shall have a rated operating voltage of 120 VAC Series MAX DC shall have a rated operating voltage range of VDC Series MAX AC and DC shall have a strobe with flash energy of 7.5 joules and flash rate of 60 double flashes per minute. Series MAX MAXS AC and DC shall have the addition of two 7 watt incandesent lamps for steady light applications. Steady light lamps shall be 7C7 type for Series MAX AC-MAXS models and 2470X type for Series MAX DC-MAXS models. Lens colors; amber, blue, clear and red shall conform to SAE J578D specifications. Base and lens shall be constructed of high strength, high temperature G.E. Lexan. Operating temperature range for all models shall be; -31 F to F (-35 C to + 66 C). Dimensions shall be Height; 5, Diameter; 6.2. Weight shall be 2 lbs. Specifications and Ordering Information Model Number Order Lens Color Voltage Product Description Effective Candela (cd) AC-MAX-A 8120 Amber 120 VAC Double Flash MAX Strobe 80 AC-MAX-B 8121 Blue 120 VAC Double Flash MAX Strobe 12 AC-MAX-C 8122 Clear 120 VAC Double Flash MAX Strobe 100 AC-MAX-R 8124 Red 120 VAC Double Flash MAX Strobe 20 AC-MAXS-A 8125 Amber 120 VAC Double Flash MAX Strobe w/ two 7 watt steady light lamps 80 AC-MAXS-B 8126 Blue 120 VAC Double Flash MAX Strobe w/ two 7 watt steady light lamps 12 AC-MAXS-C 8127 Clear 120 VAC Double Flash MAX Strobe w/ two 7 watt steady light lamps 100 AC-MAXS-R 8129 Red 120 VAC Double Flash MAX Strobe w/ two 7 watt steady light lamps 20 DC-MAX-A 8130 Amber VDC Double Flash MAX Strobe 80 DC-MAX-B 8131 Blue VDC Double Flash MAX Strobe 12 DC-MAX-C 8132 Clear VDC Double Flash MAX Strobe 100 DC-MAX-R 8134 Red VDC Double Flash MAX Strobe 20 DC-MAXS-A 8135 Amber VDC Double Flash MAX Strobe w/ two 7 watt steady light lamps 80 DC-MAXS-B 8136 Blue VDC Double Flash MAX Strobe w/ two 7 watt steady light lamps 12 DC-MAXS-C 8137 Clear VDC Double Flash MAX Strobe w/ two 7 watt steady light lamps 100 DC-MAXS-R 8139 Red VDC Double Flash MAX Strobe w/ two 7 watt steady light lamps 20 Model AC-MAX and AC-MAXS AC-MAX and DC-MAXS Current Draw 120 VAC VDC VDC VDC VDC Steady Light Lamps Current Draw DC Inrush Current Draw: 12V 5A Max 24V 10A Max 31V 12A Max Note: Series MAX Strobes are not intended for use in wash down areas. AC-MAXS Models DC-MAXS Models 120 ma 665 ma NOTE: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Wheelock Inc. standard terms and conditions. 273 Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA I1008 Max 06/06

13 EMNA Emergency Mass Notification Appliance EMNA Description: The Emergency Mass Notification Appliance (EMNA) is a combination appliance consisting of 1 E70 or ET70 Multicandela Wall Speaker Strobe, 1 RSSP Colored Lens Strobe Plate (Amber, Blue, Green or Red) and 1 ISP-2 and/or SPL-2 backbox. The E70 Low Profile Speaker Strobes are designed for high efficiency sound output, with dual voltage (25/70 VRMS) capability and field selectable taps from 1/8 to 2 watts. The Series ET70 Speaker Strobes provide high audio output, clear audibility, dual voltage (25/70 VRMS) capability and field selectable taps from 1/8 to 8 watts. The strobe portion of the Series E70 and ET70 Speaker Strobes may be synchronized when used in conjunction with the Wheelock SM, DSM Sync Modules or Wheelock s PS- 12/24-8CP and PS-12/24-8MP Power Supplies with Wheelock Patented Sync Protocol. The Series RSSP Strobe Plates are a cost effective way to retrofit colored lens strobe appliances to speakers and easily mounts to standard 4 backboxes or for surface mount use with Wheelock s SBL2 surface backbox. The strobes are available in amber, blue, green and red. The strobes operate from 16 to 33 vdc (using filtered or FWR voltage). Intensity options for amber, blue and green lens strobes include multi-candela models with four field-selectable settings or 110 candela models. Red lens strobes are available in 75 or 110 candela models and are Listed under UL Standard Applications for EMNA: Mass Notification Systems Hazard warning/alerting Security alert indication Personnel alerting (Pictures includes: RSSPA-24MCC-NW, E70-24MCW-FW and backboxes SBL-2 and ISP-2) Features: (E70 and ET70) Approvals include: UL Standard 1971, UL Standard 1480, New York City (MEA), California State Fire Marshal (CSFM), Factory Mutual (FM) and Chicago (BFP) See approvals by model in Specifications and Ordering Information Compliant with UFC , ADA, OSHA L Wall mount models are available with Field Selectable Candela Settings of 15/30/75/110cd Strobes produce 1 flash per second over the regulated voltage range 24 VDC with wide UL Regulated Voltage using filtered DC or unfiltered VRMS input voltage Synchronize with Wheelock SM, DSM or Wheelock PS-12/24-8CP and PS-12/24-8MP Power Supply with built-in sync protocol High efficiency design for maximum output at minimum wattage across a frequency range of 400 to 4000 HZ (RSSP Colored Lens Strobe Plates) Approvals include: UL Standard 1638 Choice of four strobe lens colors with wide range of intensity options Wide operating voltage range Strobes can be synchronized with Wheelock s SM or DSM sync modules or POWERPATH power supplies Combination speaker/strobes available for voice messages with visual alerting Mount to standard electrical boxes High quality designs from the leader in fire notification alarms

14 SPECIFICATIONS AND ORDERING INFORMATION Model Number Order Lens Color Strobe Candela Mounting Options Strobe Voltage Strobe Current (RMS) note 1 note 2 16 vdc 24 vdc Agency Approvals RSSPA-24MCC-NW 3308 AMBER MCC wall or ceiling 24 vdc note 3 none RSSPB-24MCC-NW 3306 BLUE MCC wall or ceiling 24 vdc note 3 none RSSPG-24MCC-NW 3307 GREEN MCC wall or ceiling 24 vdc note 3 none RSSPR NW 3309 RED 110 wall or ceiling 24 vdc UL, CSFM, MEA, BFP E70-24MCW-FW 9023 CLEAR MCW wall 24 vdc note 4 UL, CSFM, MEA, BFP ET70-24MCW-FW 9021 CLEAR MCW wall 24 vdc note 4 ISP2-W 3195 N/A N/A N/A N/A N/A N/A N/A SBL2-W 6989 N/A N/A N/A N/A N/A N/A N/A Note 1. Candela is measured on axis per UL Models with MCC strobes have 4 field selectable candela settings. MCC settings are rated for clear lens - derate approximately 25% for amber, 55% for green and 70% for blue Note 2. All strobes operate from 16 to 33 volts at 1 flash/second using filtered or full-wave-rectified DC voltage (See Installation Instructions) Note 3. Strobe Current for MCC Strobes: MCC setting vdc vdc Note 4. Strobe Current for MCW Strobes: MCW setting vdc vdc Military and Government Systems offered by Wheelock Refer to the products Installation Instructions for proper installation, wiring procedures and any additional specifications. Operational and Storage Specifications: Temperature Range: 32 F F (0-49 C) Humidity Range: 0-85% Non-Condensing SPECIAL ORDER Wheelock systems meet all requirements of the Unified Facilities Criteria (UFC) , 18 December 2002 UFC Performance Criteria for Mass Notification System for the Interior of Structures Personnel Alert Systems (PAS) Provide force protection and early warning in emergency situations including: Bomb Threat, Terrorist Attack, Security Breach, Chemical Release, Natural Disaster and OEM Wheelock Wireless Platform for Base Wide (exterior) and Building Facility (interior) Systems Mass Notification Systems (MNS) Secure Systems for SCIF room applications Contact your Wheelock representative for additional information regarding base or facility site visits and equipment recommendations. For additional specifications, refer to the following data sheets: S0310 Series ET Speaker Strobes S1610 Series E Speaker Strobes S9020 Series RSS Colored Lens Strobes S7000 Mounting Accessories Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Wheelock Inc. standard terms and conditions. 273 Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA M1000 EMNA 06/06

15 Series STH-15S Supervised Horn Loudspeaker STH-15S (Gray) STH-15SR (Red) SHMP-R Adapter Plate Description The Wheelock Series STH-15S supervised horn loudspeakers are equipped with a compression driver providing up to 15 watts RMS power handling capability, superior intelligibility and dispersion to achieve maximum sound projection and penetration. Weather-resistant metal construction and reentrant acoustic path assure protection against water, humidity, vermin and corrosion. The mounting bracket allows directional sound dispersion via vertical and horizontal positioning. Provisions are also included for surface or strap mounting to pillars and I-beams. All models include a built-in 25/70/100 V transformer featuring a screwdriver adjustable, 7-position watt/impedance selection switch. Wiring terminals are protected with a vandal-resistant adapter cover for control equipment utilizing cable or conduit. A built-in, 5 mfd capacitor is provided on both models for line supervision. All models meet or exceed the UL Listed standards for audible signal appliances and are capable of operating within an ambient temperature range of 66 C (150 F) to -35 C (-30 F). Models comply with UL Standard 1480 Speakers for Fire Protective Signaling Systems and California State Fire Marshal (Title 19). Features Approvals include: UL Standard 1480 (Speakers for Fire Protective Signaling Systems), California State Fire Marshal (CSFM) Title 19 Meets or exceeds UL Listed standards for audible signal appliances 15-Watt High Efficiency Compression Driver Weather-resistant, vandal-resistant aluminum construction assures protection against water, humidity, vermin, and corrosion Reentrant acoustic path 25/70/100 V transformer featuring a screwdriver adjustable, 7- position watt/impedance selection switch 5 mfd Capacitor for Line Supervision STH-15S Gray baked epoxy finish STH-15SR Red baked epoxy finish Simplified, universal-mounting bracket adjustable in horizontal and vertical planes with banding slots for beam or pillar mounting Installation terminals and power selector are recessed mounted, and protected by the metal interface adapter, or clear plastic shield Applications The Wheelock Series STH-15S supervised horn loudspeakers are surface-mounting, high-efficiency units for life safety and communication system applications. When used with compatible control equipment, they provide high-intelligibility voice reproduction and signal transmission for indoor or outdoor emergency alarm and protective signaling. Specifications and Ordering Information Model Number Order Product Description Weight STH-15S Dia. Supervised, Weatherproof, 15 Watt Horn, Loudspeaker with Transformer, Aluminum, Gray 4.5 lbs. (2.0 kgs.) STH-15SR Dia. Supervised, Weatherproof, 15 Watt Horn, Loudspeaker with Transformer, Aluminum, Red 4.5 lbs. (2.0 kgs.) SHMP-R 8154 STH- RSSP-KIT 6096 UL Listed Adapter Plate, Designed to mount the STH-15SR Horn Speaker (7938) to a Series RSSP Strobe Mounting Plate. For Surface Mount Applications, the SBL-2 (6988) Surface mount backbox is required. Weatherproof 15 watt supervised 25/70 horn loudspeaker and 15/30/75/110cd strobe with mounting plate, adjustable mounting base for horn and backbox. Red color. U L S E :144

16 Architects and Engineers Specifications The supervised horn loudspeaker shall be a STH-15S/STH-15SR or approved equal. The horn shall be weather resistant and constructed of heavy gauge, treated aluminum. The horn shall be able to operate within any ambient temperature environment ranging from 66 degrees C (150 F) to -35 degrees C (-30 F). The horn shall be a double reentrant type with a 15 watt RMS audio power rated compression driver producing a UL rated 102 db measured at 15 watts at 10 feet. The horn shall have an impedance selection via a 7 position switch of 5000, 2500, 1300, 666, 333, 89 & 45. Power taps shall be available at 2.0, 4.0, 7.5 & 15 watts for the 100 volt line,.9, 1.8, 3.8, 7.5 & 15 watts for the 70 volt line and.48,.94, 1.8, 7.5 & 15 watts for the 25 volt line. Each power tap shall have a 3dB incremental rating. The frequency response range shall be Hz. The horn shall have a dispersion of 70 degrees. The horn assembly shall be furnished with a mounting bracket that allows adjustment on either a vertical or horizontal plane with a single locking pin and include provisions for mounting, banding or strapping. Wiring terminals shall be fully enclosed and a vandal-resistant adapter cover shall provide connection protection for cable or conduit. The horn shall be W x 8.75 H x D (200 x 222 x 237 mm). The horn shall be finished in gray (STH-15S) or red (STH-15SR) baked epoxy. WARNING: PLEASE READ THESE SPECIFICATIONS AND INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING, SPECIFYING OR AP- PLYING THIS PRODUCT. FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS, CAUTIONS AND WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS. STH-15S & STH-15SR Power Switch Selections Setting Impedance (Ohms) Watts 70.7 Volts 25 Volts 100 Volts 10 Feet Watts 10 Feet Watts 10 Feet 1 5, W 90 Not Used Not Used 2.0W , W 93 Not Used Not Used 4.0W , W W W W W W W W 93 Not Used Not Used 6 89 Not Used Not Used 7.5W 99 Not Used Not Used 7 45 Not Used Not Used 15.0W 102 Not Used Not Used Specifications (UL RATING) POWER RATING: 15 Watt Continuous FREQUENCY RESPONSE: 400-4,000 Hz SENSITIVITY: SPECIFICATIONS GENERAL DISPERSION ANGLE: 70 Degrees (-6 2,000 Hz Octave Band) Anechoic Measurements: 15 watt 10 feet -3 Tone Slow Whoop Siren dba dba dba NOTE: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Wheelock Inc. standard terms and conditions. 273 Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA S0100 STH 11/06

17 Series CVX/CSX Explosion -Proof Bells Description: Wheelock s Series CVX/CSX Explosion-Proof Bells have earned the reputation for rugged, reliable performance over years of service in hazardous environments. These bells are Listed for service in Division One applications which means that they are designed to operate safely in atomospheres that actually contain the explosive elements in free form (in contrast to Division Two environments, wherein the explosive elements are stored and protected). Features: Approvals include: UL Standard, New York (MEA) and California State Fire Marshal (CSFM) Rugged cast mechanism enclosure Available in single stroke and vibrating models Available in 24 VDC and 115 VAC versions High sound output with large 10 bell shell Outdoor models include protective hood and guard CLASS GROUP CONTENTS OF HAZRDOUS ATMOSPHERE I B Hydrogen or Gases & Vapors of equivalent hazard such as Manufactured Gas I C Ethyl & Ether Vapors I D Gasoline, Petroleum, Naphtha, Alcohol, Acetone, Benzene, Lacquer Solvent, Vapors, Natural Gas II F Carbon Black, Coal, Coke Dust II G Flour, Starch, Grain Dusts Vibrating Listed for Hazardous Atmospheres Specification and Ordering Information: Indoor Model Number Order Outdoor Model Number Order Shell Size Input Volt. Input Current 10 Ft. Mounting CVX R* 3742 CVXG R* VAC Note 1 CVX S* 0132 CVXG S* VAC Note 1 Single Stroke Indoor Model Number Order Outdoor Model Number Order CSX R* 4715 CSXG R* 4929 Shell Size Input Volt. Input Current 115VAC CSX S* 0166 CSXG S* VAC CSX10-24-R 3582 CSXG10-24-R VDC CSX10-24-S 0164 CSXG10-24-S VDC Ft. Mounting 87 Note 1 E5946 S E :142 NOTES: 1. All models Include integral cast backbox for surface mounting with 1 /2 threaded conduit entrances on top and bottom of housing. 2. Wheelock also offers a line of explosion-proof relays. Consult Customer Service for information.

18 ARCHITECTS AND ENGINEERS SPECIFICATIONS The alarm bells shall be Wheelock Series CVX/CSX explosion-proof bells or approved equals. They shall be UL Listed for Hazardous Atomospheres, and suitable for use in Division One applications: Class One, groups B, C and D; and Class Two, groups F and G. Specific models shall be designed for either single stroke or vibrating mode, and operation for either 24 VDC or 115 VAC. Sound output at 10 feet shall be 87 dba for single stroke versions and 90 dba for the vibrating version. All versions shall be polarized for DC supervision. Operating current shall be as follows:.220 amperes for 115 VAC vibrating,.125 amperes for 115 VAC single stroke;.500 amperes for 24 VDC single stroke. Outdoor versions shall incorporate a cast protective hood and guard over the bottom half of the bell shell. Dimensions for the indoor versions shall be 10 and one-eighth inches wide, 11 inches high and 6 and one-half inches deep. Outdoor versions shall measure 11 and one-half inches wide, 11 and one-half inches high, and 7 and one-half inches deep. Wheelock products must be used within their published specifications and must be PROPERLY specified, applied, installed, operated, maintained and operationally tested in accordance with their installation instructions at the time of installation and at least twice a year or more often and in accordance with local, state and federal codes, regulations and laws. Specification, application, installation, operation, maintenance and testing must be performed by qualified personnel for proper operation in accordance with all of the latest National Fire Protection Association (NFPA), Underwriters Laboratories (UL), National Electrical (NEC), Occupational Safety and Health Administration (OSHA), local, state, county, province, district, federal and other applicable building and fire standards, guidelines, regulations, laws and codes including, but not limited to, all appendices and amendments and the requirements of the local authority having jurisdiction (AHJ). WARNING: PLEASE READ THESE SPECIFICATIONS AND ASSOCIATED INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING, SPECIFYING OR APPLYING THIS PRODUCT. FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS, CAUTIONS OR WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS. NOTE: Due to continuous development of our products, specifications and offerings are subject to change without notice in accordance with Wheelock Inc. standard terms and conditions. 273 Branchport Avenue Long Branch, NJ Phone: (800) Fax: (732) WE ENCOURAGE AND SUPPORT NICET CERTIFICATION 3 YEAR WARRANTY Made in USA S0200 CVX/CSX 05/06

19 Series ET Speakers and Speaker Strobes SERIES ET70 Description The Wheelock high performance Series ET Speakers and Series ET Speaker Strobes provide high audio output, clear audibility, dual voltage (25/70 VRMS) capability and field selectable taps from 1/8 to 8 watts. They are designed to meet the critical needs of the life safety industry for effective emergency voice communications, tone signaling and visible signaling to alert the hearing impaired. The low profile design incorporates a speaker mounting plate for faster and easier installation. Each model has a built-in level adjustment feature and an aesthetic two (2) screw grille cover. The Series ET Speaker Strobe models incorporate Low Current draw Series RSS Strobes. Strobe options for wall mount models include 1575 cd or Wheelock s patented MCW multi-candela strobe with field selectable candela settings of 15/30/75/110cd or the high intensity MCWH strobe with field selectable 135/185cd. Ceiling mount models are available in Wheelock s patented MCC multi-candela ceiling strobe with field selectable intensities of 15/30/75/95cd or the high intensity MCCH strobe with field selectable 115/177cd. The strobe portion of all Series ET Strobes may be synchronized when used in conjunction with the Wheelock SM, DSM sync modules or the Wheelock PS-24-8MC Power Supplies with patented Sync Protocol. Wheelock synchronized strobes offer an easy way to comply with ADA recommendations concerning photosensitive epilepsy. Series ET70 and ET90 Speaker Strobes are UL Listed for indoor use under Standard 1971 (Signaling Devices for the Hearing Impaired) and Standard 1480 (Speaker Appliances), and use a Xenon flashtube with solid state circuitry enclosed in a rugged Lexan lens to provide maximum reliability for effective visual signaling. All inputs are supervised and employ IN/OUT wiring terminals for fast installation using #12 to #18 AWG wiring. Color options for Series ET speakers and speaker strobes are red, white, or nickel plated. SERIES ET90 Features Approvals include: UL Standard 1971, UL Standard 1480, New York City (MEA), California State Fire Marshall (CSFM), Factory Mutual (FM), and Chicago (BFP) See approvals by model in Specifications and Ordering Information ADA/NFPA/UFC/ANSI compliant Meets OSHA 29 Part Wall mount models are available with Field Selectable Candela Settings of 15/30/75/110cd or 135/185cd (Multi-Candela models) or 1575cd (Single Candela model) Ceiling mount models are available with field selectable candela settings of 15/30/75/95cd or 115/177cd (multi-candela models) Strobes produce 1 flash per second over the regulated voltage range 24 VDC with wide UL Regulated Voltage using filtered DC or unfiltered VRMS input voltage Synchronize with sync modules or power supplies with built-in sync protocol Field selectable taps for 25 or 70 VRMS operation from 1/8 watt to 8 watts High efficiency design for maximum output at minimum wattage across a frequency range of 400 to 4000 HZ Fast installation with IN/OUT screw terminals using #12 to #18 AWG wires U L THE CITY OF NEW YORK DEPARTMENT OF BUILDINGS S5391 S E :152 (ET70/90 MC) :146 (ET70WP)

20 NOTE: All CAUTIONS and WARNINGS are identified by the symbol. All warnings are printed in bold capital letters. WARNING: PLEASE READ THESE SPECIFICATIONS AND ASSOCIATED INSTALLATION INSTRUCTIONS CAREFULLY BEFORE USING, SPECIFYING OR APPLYING THIS PRODUCT. VISIT OR CONTACT COOPER WHEELOCK FOR THE CURRENT INSTALLATION INSTRUCTIONS. FAILURE TO COMPLY WITH ANY OF THESE INSTRUCTIONS, CAUTIONS OR WARNINGS COULD RESULT IN IMPROPER APPLICATION, INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD RESULT IN PROPERTY DAMAGE, AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS. General Notes: Strobes are designed to flash at 1 flash per second minimum over their Regulated Voltage Range. Note that NFPA-72 specifies a flash rate of 1 to 2 flashes per second and ADA Guidelines specify a flash rate of 1 to 3 flashes per second. All candela ratings represent minimum effective Strobe intensity based on UL Standard Series NS Strobe products are listed under UL Standard 1971 for indoor use with a temperature range of 32 F to 120 F (0 C to 49 C) and maximum humidity of 93% (± 2%). Series NH horns are listed under UL Standard 464 for audible signal appliances (Indoor use only). Regulated Voltage Range is the newest terminology used by UL to identify the voltage range. Prior to this change UL used the terminology Listed Voltage Range. Table 1: UL Max Current* ET70/ET90 Speaker Strobes ET70 Strobe current - Wall Mount ET90 Strobe current - Ceiling Mount W 24MCW 24MCWH 24MCC 24MCCH 1575cd 15cd 30cd 75cd 110cd 135cd 185cd 15cd 30cd 75cd 95cd 115cd 177cd VDC Table 2: ET70/ET90 UL Reverberant 10 Feet** watts 1/8 1/4 1/ ET Speaker ET Speaker Strobe **dba ratings are based on UL testing under UL Standard 1480 *UL max current rating is the maximum RMS current within the listed voltage range (16-33v for 24v units). For strobes the UL max current is usually at the minimum listed voltage (16v for 24v units). For audibles the max current is usually at the maximum listed voltage (33v for 24v units). For unfiltered FWR ratings, see installation instructions.