INDEX Meaningful Information COMBO-D-LUX COMBO-QUICK-SET COMBO COMBO-DIAPHRAGM

Transcription

1 COMBO-DIAPHRAGM EAD

2

3 INDEX Meaningful Information COMBO-D-LUX COMBO-QUICK-SET COMBO COMBO-DIAPHRAGM CONDENSATE DRAINS OPTIMUM EAD TEC-44 TEC-11 TEC-55 OPTIMUM High Pressure Service Kits Electronic Timers BVS, Coils & Connectors Accessories Condensate Management Specialist

4 Information provided herewith is believed to be accurate and reliable. However, no responsibility is assumed for its use or for any infringement of patents or rights of others, which may result from its use. In addition, JORC reserves the right to revise information without notice and without incurring any obligation.

5 CONDENSATE Condensation is the moisture that drops out of an air flow as it cools. The condensation in a compressed air system is a constant threat to cause expensive problems. The following are a few examples: Moisture washes lubrication from air tools and production equipment causing downtime and maintenance. An inconsistent supply of dry air causes production quality problems. Excessive rust and scale often forms in the air distribution system. Water can back up into the compressor and wreck the machinery. Air dryers can become overloaded. In-line filters can be destroyed. The problems get worse if you operate lubricated reciprocating or oil flooded rotary screw compressors - which is just about everyone. Compressor oil makes its way into the distribution system with the compressed air. The mixture of oil, water, dirt and heat tends to build up a sludge that will ultimately jam or clog production equipment, air tools and drains. MEANINGFUL INFORMATION The situation is further complicated by climate and seasonal weather changes. This is because the amount of condensation generated will change according to changes in the temperature and the relative humidity of the inlet air. The typical compressed air system is designed to remove condensation at strategic locations. This means there are drains at the after cooler separator, receiver tank, air dryer, in-line filters and at drain points in the piping. PRODUCT SELECTION JORC produces a vast range of condensate drains. We manufacture/market zero air loss drains, timer controlled drains, powerful motorized ball valve drains and a line of drains that DO NOT require electricity. JORC drains are the most reliable in the world and combined with the wide product selection, we truly do offer one stop shopping. A whole range of private labelling options are available to make you and your JORC drain stand out and be noticed. JORC drains are complemented with a complete range of the superior performing oil/water separating range - the PURO. JORC air saving products are unique and offer an immense opportunity for energy conservation.

6 CERTIFICATIONS CE The CE Marking applies to products regulated by certain European health, safety and environmental protection legislation. The CE Marking is obligatory for products it applies to, the manufacturer affixes the marking in order to be allowed to sell his product in the European market. JORC products are CE certified. CULUS The UL Recognized Component Mark, which became effective April 1, 1998, may be used on components certified by UL to both Canadian and U.S. requirements. Although UL had not originally planned to introduce a combined Recognized Component Mark, the popularity of the Canada/U.S. Listing and Classification Marks among clients with UL certifications for both Canada and the United States has led to the new Mark. JORC products, where applicable, are culus certified. ISO-9000 The ISO 9001 certificate is primarily concerned with "quality management". This means what the organization does to fulfil: - the customer's quality requirements, and - applicable regulatory requirements, while aiming to - enhance customer satisfaction, and - achieve continual improvement of its performance in pursuit of these objectives.

7 ROHS NORMS The RoHS Directive bans the use of certain restricted substances in end products, which prevents the substances from entering waste streams. According to the directive, new electrical equipment placed on the market within Europe cannot contain more than maximum allowable levels of: Lead, Cadmium, Mercury, Hexavalent chromium, Polybrominated, bipenyl (PBB), Polybrominated diphenyl ether (PBDE). Among the RoHS Directive's largest impacts to manufacturers is the transition from the use of lead solders to lead-free solders. JORC s products are ROHS compliant. IP65/NEMA 4 This standard describes a system for classifying the degrees of protection provided by the enclosures of electrical equipment. These standards are designed to numerically rate an electrical product on the level of protection its enclosure provides. JORC products are (IP65/Nema 4) dust tight and protected against powerful water jets.

8 COMBO-D-LUX COMBO-D-LUX Timer controlled condensate drain PRODUCT FEATURES The COMBO-D-LUX is designed to remove condensate from compressors, compressed air dryers and receivers up to any size, type or manufacturer. The COMBO-D-LUX is an all-in-one digital timer drain with an integrated ball valve and strainer. The unit offers true digital time cycle programming luxury. COMMERCIAL BENEFITS Does not air-lock during operation Compressed air systems up to any size Digital illuminated cycle display Suitable for all types of compressors TEST (micro-switch) feature TECHNICAL ADVANTAGES Exceptionally accurate cycle timing Premium pcb components selected. Direct operated valve not diaphragm type Medium pressure up to 300 PSI The direct acting valve is serviceable

9 PRODUCT DIMENSIONS PRODUCT SPECIFICATIONS Maximum compressor system capacity Unlimited Valve connection options 1/2 O.D X1/4 I.D. Inlet, 1/2 Outlet NPT Minimum system pressure 0 PSI Maximum system pressure 300 PSI Supply Voltage 12 VDC, 24 VAC/VDC, 115, 230 Volt Minimum medium temperature 34 F Maximum medium temperature 130 F Valve orifice 4.0 mm Type of operating valve Direct acting Valve seals FPM (Viton) Installation enclosure IP65/NEMA 4 Time cycle range (ON - OFF) 0.1 mille-second 99 hours 25.4MM =1 COMBO-D-LUX TECHNICAL SPECIFICATIONS WHERE TO INSTALL

10 COMBO-QUICK-SET COMBO-QUICK-SET Timer controlled condensate drain PRODUCT FEATURES The COMBO-QUICK-SET is designed to remove condensate from compressors, compressed air dryers and receivers up to any size, type or manufacturer. The COMBO-QUICK-SET saves installation time and protects against large particles found in condensate, thanks to the integrated ball valve and strainer. The unit can be shut off from the compressed air system, enabling easy and safe work to be carried out. COMMERCIAL BENEFITS Does not air-lock during operation Compressed air systems up to any size Dual thread inlet (1/2 & 1/4") The direct acting valve is serviceable Suitable for all types of compressors TEST (micro-switch) feature TECHNICAL ADVANTAGES Simply select the compressor capacity and pressure and GO! Medium pressure up to 300 PSI Integrated mesh strainer

11 PRODUCT DIMENSIONS PRODUCT SPECIFICATIONS Maximum compressor system capacity See timer indication Valve connection options 1/2 O.D X 1/4 I.D. Inlet, 1/2 Outlet NPT Minimum system pressure 0 PSI Maximum system pressure 300 PSI Minimum medium temperature 34 F Maximum medium temperature 130 F Valve orifice 4.0 mm Type of operating valve Direct acting Valve seals FPM (Viton) Voltage range options 12 VDC, 24 VAC/VDC, 115,230V Installation enclosure IP65/NEMA MM =1 COMBO-QUICK-SET TECHNICAL SPECIFICATIONS WHERE TO INSTALL

12 COMBO COMBO Timer controlled condensate drain PRODUCT FEATURES The COMBO is designed to remove condensate from compressors, compressed air dryers and receivers up to any size, type or manufacturer. The COMBO saves installation time and protects against large particles found in condensate, thanks to the integrated ball valve and strainer. The unit can be shut off from the compressed air system, enabling easy and safe work to be carried out. COMMERCIAL BENEFITS Does not air-lock during operation Compressed air systems up to any size Dual thread inlet (1/2 & 1/4") The direct acting valve is serviceable Suitable for all types of compressors TEST (micro-switch) feature TECHNICAL ADVANTAGES Direct operated valve not diaphragm type Medium pressure up to 300 PSI Integrated mesh strainer

13 PRODUCT DIMENSIONS 25.4MM =1 PRODUCT SPECIFICATIONS Maximum compressor system capacity Unlimited Valve connection options 1/2 O.D X 1/4 I.D. Inlet, 1/2 Outlet NPT Minimum system pressure 0 PSI Maximum system pressure 300 PSI Minimum medium temperature 34 F Maximum medium temperature 130 F Valve orifice 4.0 mm Type of operating valve Direct acting Valve seals FPM (Viton) Installation enclosure IP65/NEMA 4 Voltage range options 12VDC, 24VAC/VDC, 115, 230V Time cycle range (ON - OFF) 0.5/10 seconds 0.5/45 minutes COMBO TECHNICAL SPECIFICATIONS WHERE TO INSTALL

14 COMBO-DIAPHRAGM COMBO-DIAPHRAGM Timer controlled condensate drain PRODUCT FEATURES The COMBO-DIAPHRAGM is designed to remove condensate from compressors, compressed air dryers and receivers up to any size, type or manufacturer. COMMERCIAL BENEFITS Compressed air systems up to any size The valve is serviceable Suitable for all types of compressors TEST (micro-switch) feature TECHNICAL ADVANTAGES Large orifice 7/16 Medium pressure up to 300 PSI PRODUCT SPECIFICATIONS Maximum compressor system capacity Unlimited Valve connection options 1/4, 3/8 & 1/2 NPT Minimum system pressure 1.5 PSI Maximum system pressure 300 PSI Minimum medium temperature 4 F Maximum medium temperature 130 F Valve orifice 7/16 Type of operating valve Diaphragm Valve seals FPM (Viton) Installation enclosure P65/NEMA 4 Voltage range options 10 to 380VAC/DC 50/60 Hz. Time cycle range (ON - OFF) 0.5/10 seconds 0.5/45 minutes

15 PRODUCT DIMENSIONS 25.4MM =1 The forged brass valve body has a full port 7/16-inch drain orifice. This large orifice virtually eliminates clogging by rust, scale or other air system debris and can discharge more than two gallons of condensate per drain opening at 100 psig. Jorc does recommend the use of a strainer in front of any diaphragm valve. The valve does have a large orifice, but the diaphragm needs to be protected. This is a diaphragm and its function is to lift up to expose a large orifice. If the bleed orifice in the diaphragm clogs then the diaphragm will not lift up, the valve is deemed blocked, and stays closed. COMBO-DIAPHRAGM TECHNICAL SPECIFICATIONS WHERE TO INSTALL

16 OPTIMUM OPTIMUM Timer controlled condensate drain PRODUCT FEATURES The OPTIMUM is designed to remove condensate from compressors, compressed air dryers and receivers up to any size, type or manufacturer. The OPTIMUM offers true installation simplicity and it is recognized as the most reliable and best performing condensate drain worldwide. The large orifice in the direct acting valve, combined with its sophisticated timer module ensure many years of trouble-free draining of condensate. COMMERCIAL BENEFITS Does not air-lock during operation Compressed air systems up to any size Also available in stainless steel The direct acting valve is serviceable Suitable for all types of compressors TEST (micro-switch) feature TECHNICAL ADVANTAGES High time cycle accuracy. Premium pcb components selected. Large (4.5 mm) valve orifice Medium pressure up to 230 PSI (for higher see OPTIMUM-HP)

17 PRODUCT DIMENSIONS PRODUCT SPECIFICATIONS 25.4MM =1 Maximum compressor system capacity Unlimited Valve connection options 1/2, 3/8 and 1/4 NPT Minimum system pressure 0 PSI Maximum system pressure 230 PSI (for higher pressures see OPTIMUM-HP) Minimum medium temperature 34 F Maximum medium temperature 130 F Valve orifice 4.5 mm Type of operating valve Direct acting Valve seals FPM (Viton) Installation enclosure IP65/NEMA 4 Voltage range options 12VDC, 24VAC/VDC, 115, 230V Time cycle range (ON - OFF) 0.5/10 seconds 0.5/45 minutes OPTIMUM TECHNICAL SPECIFICATIONS WHERE TO INSTALL

18 EAD EAD Timer controlled condensate drain PRODUCT FEATURES The EAD is designed to remove condensate from compressors, compressed air dryers and receivers up to any size, type or manufacturer. The EAD offers true installation simplicity at the lowest possible cost. The EAD is a mass produced product available in various valve connection sizes and timer color options. COMMERCIAL BENEFITS Does not air-lock during operation Compressed air systems up to any size The direct acting valve is serviceable Suitable for all types of compressors TEST (micro-switch) feature TECHNICAL ADVANTAGES Simple to install Direct operated valve not diaphragm type Medium pressure up to 230 PSI Viton seals

19 PRODUCT DIMENSIONS 25.4MM =1 EAD TECHNICAL SPECIFICATIONS PRODUCT SPECIFICATIONS Maximum compressor system capacity Unlimited Valve connection options 1/2, 3/8 and 1/4 NPT Minimum system pressure 0 PSI Maximum system pressure 230 PSI Minimum medium temperature 34 F Maximum medium temperature 130 F Valve orifice 4.0 mm Type of operating valve Direct acting Valve seals FPM (Viton) Installation enclosure IP65/NEMA 4 Voltage range options 24 to 230VAC/DC 50/60 Hz. Time cycle range (ON - OFF) 0.5/10 seconds 0.5/45 minutes WHERE TO INSTALL

20 TEC-44 TEC-44 Timer controlled condensate drain PRODUCT FEATURES The TEC-44 is a microprocessor operated ball valve, designed to remove condensate from deliquescent dryers, tanks, vessels and refrigerated dryers. The TEC-44 is designed to remove high viscosity effluents at pressure ratings up to 720 PSI. This condensate drain can not be blocked and is applied where all else fails. Draining applications with a high level of contamination (rust, scale etc.) require the TEC-44. The TEC-44 is impossible to block due to its powerful ball valve rotation and large orifice. COMMERCIAL BENEFITS Does not air-lock during Operation Compressed air systems up to any size Powerful ball valve rotation (unblockable) Suitable for all types of compressors TEST (micro-switch) feature TECHNICAL ADVANTAGES Micro-processor controlled (high level of time cycle accuracy) Medium pressure up to 720 PSI Remote control possible.

21 PRODUCT DIMENSIONS PRODUCT SPECIFICATIONS Maximum compressor system capacity Unlimited Valve connection options 1/2, 3/4, & 1 NPT Minimum system pressure 0 PSI Maximum system pressure 720 PSI Minimum medium temperature 34 F Maximum medium temperature 140 F Valve orifice 12 mm Type of operating valve Motorized ball valve Valve seals FPM (Viton) and Teflon Installation enclosure IP65/NEMA 4 Voltage range options 12VDC, 24VAC/VDC, 115 or 230VAC Time cycle range (ON - OFF) 7 seconds 4 minutes/24 hours 25.4MM =1 TEC-44 TECHNICAL SPECIFICATIONS WHERE TO INSTALL

22 TEC-11 TEC-11 Timer controlled condensate drain PRODUCT FEATURES The TEC-11 removes condensate, automatically, from compressed air filters and small dental (oil free type) compressors. The clever in-line design allows for perfect installation under ALL types of compressed air filters, regardless of their capacity or size. COMMERCIAL BENEFITS Does not air-lock during operation. Suitable for Compressed air filters up to any size Suitable for all types of compressors Clever in-line design TEST (micro-switch) feature TECHNICAL ADVANTAGES Fixed ON cycle and an adjustable OFF cycle Medium pressure up to 230 PSI Standard, 300 PSI Optional Connection sizes 1/8 & 1/4" Incredibly compact design

23 PRODUCT DIMENSIONS 25.4MM =1 PRODUCT SPECIFICATIONS Maximum filter capacity Unlimited Valve connection options 1/8 & 1/4" NPT Minimum system pressure 0 PSI Maximum system pressure 230 PSI Standard, 300 PSI Optional Minimum medium temperature 34 F Maximum medium temperature 130 F Valve orifice 2 mm Type of operating valve Direct acting valve Valve seals FPM (Viton) Installation enclosure IP65/NEMA 4 Voltage range options 24 to 230VAC/DC 50/60 Hz. Time cycle range (ON - OFF) 2 seconds 1/120 minutes TEC-11 TECHNICAL SPECIFICATIONS WHERE TO INSTALL

24 TEC-55 TEC-55 Timer controlled multi-point condensate drain PRODUCT FEATURES The TEC-55 is a multi-point timer controlled condensate drain, designed to control up to four valves (draining points). A typical compressor installation has a compressor, after cooler, dryer, filter(s) and a receiver (air tank). All draining points can now be centrally controlled by the TEC-55. This multi-voltage, sequential controller can drain up to four outlets and each outlet can vary in pressure rating ranging from 0 to 7000 psi. The valves are purged sequentially therefore subsequent pressure drop is minimized. COMMERCIAL BENEFITS Does not air-lock during Operation. Compressed air systems up to any size. One valve control point. Suitable for all types of compressors. TECHNICAL ADVANTAGES Minimum pressure drop due to sequential valve purging. Any type of valve can be applied (direct acting, diaphragm etc.). Various pressure ranges possible (multi-stage compressor applications etc.).

25 PRODUCT DIMENSIONS 25.4MM =1 PRODUCT SPECIFICATIONS Maximum compressor system capacity Unlimited Valve connection options 1/8 up to 2 NPT Minimum system pressure 0 bar Maximum system pressure Up to 7000 PSI, Depends on Valve selection Minimum medium temperature 34 F Maximum medium temperature 140 F Valve orifice Depending on the valve type Type of operating valve Various possibilities (direct acting, diaphragm, etc.) Valve seals Depending on the valve type Voltage range options 10 to 380VAC/DC 50/60 Hz. Installation enclosure IP65/NEMA 4 TEC-55 TECHNICAL SPECIFICATIONS WHERE TO INSTALL

26 OPTIMUM-HP OPTIMUM-HP Timer controlled condensate drain for high pressure applications. PRODUCT FEATURES The OPTIMUM-HP is designed to remove condensate from high pressure compressed air systems. The OPTIMUM-HP offers true installation simplicity and it is recognized as the most reliable and best performing condensate drain worldwide. The OPTIMUM-HP offers trouble free condensate draining on systems up to 7000 PSI. COMMERCIAL BENEFITS Does not air-lock during operation. Compressed air systems up to any size. The direct acting valve is serviceable. Suitable for all types of compressors. TEST (micro-switch) feature. TECHNICAL ADVANTAGES Direct operated valve not diaphragm type. Brass and stainless steel valve bodies depending on pressure range. Pressure up to 7000 PSI.

27 PRODUCT DIMENSIONS 25.4MM =1 PRODUCT SPECIFICATIONS Maximum compressor system capacity Unlimited Valve connection options 1/4, 1/2 NPT 600, 1200 PSI 1/4 Only for 3625, 5000, 6000, 7000 PSI Valve Body Brass or Stainless Minimum system pressure 0 PSI Maximum system pressure 7000 PSI (depending on model) Minimum medium temperature 34 F Maximum medium temperature 130 F Valve orifice Depending on the pressure range Type of operating valve Direct Acting Valve seals Depending on the pressure range Installation enclosure IP65/NEMA 4 Voltage range options 10 to 380VAC/DC 50/60 Hz. Time cycle range (ON - OFF) 0.5/10seconds 0.5/45 minutes OPTIMUM-HP TECHNICAL SPECIFICATIONS WHERE TO INSTALL

28 ELECTRONIC TIMERS TEC-11, TEC-22, OPTIMUM, COMBO, D-LUX & EAD Electronic timers PRODUCT FEATURES JORC produces the largest range of high quality analog and digital timers for solenoid valve applications. Typical applications include compressed air, fluid processing and dust control. Our fully automated production methods ensure consistency in manufacturing and a high product quality level. Through various housing designs and colors, we offer tailor made solutions to suit your personal desire. COMMERCIAL BENEFITS Long life durability. Easy to program. Private labelling is possible. Various housing designs and colors possible to create private labelled products. Stylish designed compact housings. TECHNICAL ADVANTAGES Surface Mounted Technology, ensuring manufacturing consistency. Cycle options ranging from Mille-seconds up to 99 hours. Analog and digital time cycle adjustment options. Digital timers offer an illuminated count down display feature.

29 PRODUCT DIMENSIONS PRODUCT SPECIFICATIONS Valve connection options DIN form A & DIN form B Housing material ABS (fire resistant) Manual TEST feature Yes Supply voltage options VAC/DC 50/60 Hz. Minimum medium temperature 34 C Maximum medium temperature 130 C Installation enclosure IP65/NEMA 4 (when installed) Cycle display mode Yes Voltage range options 10 to 380VAC/DC 50/60 Hz. Time cycle range (ON - OFF) 0.1 mille-seconds 99 hours (depending on the timer model) OPTIMUM timer illustrated. 25.4MM =1 ELECTRONIC TIMERS TECHNICAL SPECIFICATIONS INSTALLATION

30 BALL VALVE STRAINERS BALL VALVE STRAINERS L-TYPE STRAINERS The OPTIMUM, TEC-22 drain valves have an orifice of 4.5 mm (EAD 4.0mm). This large orifice ensures that emulsions and particles in compressed air cannot block the valve. We offer 1/2", 3/8 and 1/4" valves and to avoid unnecessary adapters etc. We offer the right strainer for the right valve. In addition, the inlet thread is dual threaded 1/2 O.D. X 1/4 I.D. Pressure rating of the JORC strainer is 600 PSI. TIGHTENING FIXTURE JORC ball valve strainers have an incorporated hex area to simplify the installation procedure. DUAL THREAD The JORC ball valve strainers have a dual-combination inlet thread of 1/2" (male) and a 1/4" (female). 1/2 O.D. X 1/4 I.D. This feature offers versatility during installation.

31 IN-LINE STRAINER The specially designed in-line Y ball valve strainer allows for easy local shut off of zero air loss drains for maintenance purposes. Any debris is also caught in the mesh strainer protecting the drain from any blockages and reducing maintenance to a minimum. It is specially designed to have no flow restrictions. Flow restrictions cause air-locks. BALL VALVE STRAINERS MCV (MESH CLEANING VALVE) Dirty applications that have large amounts of debris collected in the ball-valvestrainers can clog the mesh up regularly. This then requires cleaning by the end-user or by the installation engineer. The add-on MCV offers a quick blow-out of the debris with just a twist of the wrist. Simply hook the debris discharge hose pipe to the PURO oil-water-separator and you ll never need to take a ball-valve-strainer apart again. The MCV (Mesh Cleaning Valve) is available as a loose item and can therefore be mounted to ball valve strainers retrospectively.

32 ADAPTERS ADAPTERS Condensate drain installation adapters TEC-11 ADAPTERS Installation adapters simplify the job for the service technician. JORC offers a range of adapters to suit all filters (even those that do not have threads in the bowl). ANTI AIR LOCK ADAPTER The anti air lock adapter is simple to install and helps prevent air locks being created. This adapter is often applied on zero air loss type drains (timer controlled drains do not air lock). HOSE PIPE CONNECTORS Hose pipe connectors are a sure and simple way to install the discharge pipe. The diameter matches the connection to the PURO oil/water separators.

33 COILS AND CONNECTORS Solenoid coils type FORM A & B are installed on the valves and are available in all voltages. JORC S JC-TYPE COILS COILS AND CONNECTORS PRODUCT FEATURES JORC s JC-type coils are produced with H-grade coil insulation, ensuring maximum heat resistance during operation. The outer encapsulation is an ABS type material. All voltages are available ranging from VAC/DC 50/60 Hz. POWER CONNECTORS & ADAPTERS PRODUCT FEATURES Power (DIN) connectors are available in FORM A & B (square and rectangle) with or without a molded power cord. Special adapters to take connection from FORM B to FORM A, are also available.

34 SERVICE KITS SERVICE KITS Great care is taken to ensure long lasting components are selected and applied in our products. JORC products are designed in a way that makes servicing simple, quick and error free. Servicing JORC products is a cost effective way to recondition the products for many more years of draining service. TIMER DRAIN SERVICE KIT TEC-44 SERVICE KIT MOUNTING BRACKETS Wall mounting brackets allow easy installation of timer drains to walls or inside refrigerated dryers etc. The bracket kit contains all necessary hardware to complete the job.

35 COMBO VALVE MBV S EXPLOTED VIEWS TIMER DRAINS BALL VALVE STRAINERS

36 TERMS & CONDITIONS Standard Terms of Sale and Delivery of Jorc Industrial LLC Art. 1 General. 1.1 All of our offers, contracts and the execution thereof are governed exclusively by the present terms. Any derogation must be agreed with us explicitly in writing. 1.2 In the present terms, "the customer" is defined as each natural or legal person who has entered into or wishes to enter into a contract with our company, as well as the representative(s), attorney(s), legal successor(s) and heirs thereof. 1.3 The applicability of the Standard Terms maintained by the customer is explicitly excluded. 1.4 Simply by placing an order and/or taking receipt of the delivered goods, the customer accepts these standard terms and is deemed to have given tacit consent for their exclusive applicability in regard of any further orders placed orally, by telephone, telegraph, fax or in any other manner, irrespective of any written confirmation on our part. Art. 2 Offers. 2.1 All offers remain valid during the period to be indicated by us. In the absence of such a period, our offers are made without commitment and subject to contract. 2.2 All price lists, brochures and other data provided with an offer, are formulated with the utmost accuracy. They are binding for us only if such is explicitly confirmed in writing. We retain the property and intellectual property rights of all data/information provided with an offer, which must be returned to us upon our first such request. 2.3 The sending of offers and/or other documentation does not oblige us to deliver and/or accept the order. 2.4 We retain the right to refuse orders without stating reasons, and/or to supply on a cash-ondelivery basis or following payment in advance. 2.5 The customary tolerances apply to the measurements stated in offers. Art. 3 Contract. 3.1 Notwithstanding the following, a contract with us is established only once we have accepted or confirmed an order explicitly, i.e. in writing or otherwise, for instance by the actual delivery or handing-over of the goods. 3.2 The order confirmation is deemed to provide a complete and accurate representation of the contract. 3.3 Any additional terms or changes subsequently agreed and any terms agreed orally and/or undertakings given by our employees or on our behalf by our salespeople, agents, representatives or other intermediaries, will be binding for us only if confirmed by us in writing. 3.4 Each contract will be entered into on our part under the suspensive condition that the customer proves to be sufficiently creditworthy to comply financially with the contract, to be assessed exclusively by us. 3.5 Upon or after entering into the contract, we are entitled, before rendering performance or further performance thereof, to require security from the customer to ensure that the customer s payment and other obligations will be fulfilled. Art. 4 Warranty Jorc products are warranted to be free from defects in material and workmanship, under proper use, installation, application and maintenance in accordance with Jorc s written recommendations and specification for a period of one year from the date of shipment from Jorc s facility. Jorc s obligation under this warranty is limited to, and the sole remedy for any such defect shall be, the repair or replacement (at Jorc s option) of unaltered products returned to Jorc and proven to have such defect, provided such defect is promptly reported to Jorc within said warranty period. Warranty claims must be submitted and shall be processed in accordance with Jorc s established warranty claim procedure. In no event will Jorc be liable for business interruptions, loss of profits, personal injury, costs of delay or for any other special, indirect, incident or consequential losses, cost or damages. This is the only authorized Jorc warranty and is in lieu of all other express or implied warranties or representation, including any implied warranties of merchantability or fitness, or any other obligations on the part of Jorc. Jorc maintains a policy of ongoing product development and improvement. We therefore reserve the right to change dimensions specifications and design without notice. Art. 5 Delivery and delivery periods. 5.1 Unless agreed otherwise, the delivery will take place from our company premises/warehouse. As soon as the goods leave our company premises/warehouse, the risk as regards the goods will transfer to the customer. We will provide carriage-paid delivery only if and insofar as stated by us in the order confirmation, invoice or otherwise. For orders below a certain minimum size, separate administrative costs and/or carriage surcharges may be applied. 5.2 The customer is obliged to check the delivered goods and/or the packaging immediately upon hand-over for any defects or visible damage, or to carry out such checks after being notified by us that the goods are at the customer s disposal. 5.3 The customer must note or order to be noted on the delivery receipt, the invoice and/or the carriage documents, any defects or damage to the delivered goods and/or packaging present upon delivery or hand-over. Failure to do so will lead to the associated complaints not being taken into consideration. Our records are decisive in relation to such matters. 5.4 We are entitled to make delivery in parts, i.e. partial deliveries, for which we may submit separate invoices. In such cases, the customer is obliged to make payment in accordance with the relevant provisions below on Payment. 5.5 Delivery periods are given in good faith and are therefore not to be regarded as binding. On this basis, failure to deliver within the delivery period will not make us liable to pay any compensation. Following a failure to deliver within the delivery period, the customer may issue us with a written notice of default, specifying a final, reasonable period for delivery, following the expiry of which the customer will be entitled to annul the contract in writing, unless we find ourselves hindered by circumstances constituting force majeure. 5.6 If by the expiry of the delivery period the customer has not taken possession of the goods, they will be stored at the customer s disposal, for the customer s account and risk. Following a period of four weeks, we are entitled to sell these goods (privately). 5.7 Any shortfall in the proceeds of sale, as well as the costs, will be for the account of the customer, without prejudice to our other rights in the matter. Art. 6 Transportation/Risk. 6.1 In the absence of any further instructions to us by the customer, we will determine the mode of transportation, dispatch, packaging etc. with due care, without bearing any liability for it. Any specific wishes of the customer in relation to transportation/dispatch will be honoured only if the customer has declared that it will bear the additional costs involved. 6.2 The transportation of the goods will in principle in all cases take place at the risk and account of the customer, even if the carrier requires a clause to appear on the carriage documents, road waybills etc. stating that all damage incurred during carriage will be for the account and risk of the sender. 6.3 In the event of carriage-paid delivery, the transportation costs will not be charged separately. Art. 7 Force majeure 7.1 For these purposes, force majeure is defined as follows: any circumstance that is unforeseeable and/or independent of the will of the parties, due to which performance of the contract can no longer reasonably be required of us by the customer. Force majeure includes in any case the following: strikes, excessive absence through illness in our workforce, transportation problems, fire, government measures including in any case import and export bans, quota systems and interruptions to operations, as well as breaches of contract by our suppliers, as a result of which we are not or no longer able to fulfil our obligations to the customer. 7.2 If circumstances of force majeure arise, we are entitled to suspend the performance of the contract or to dissolve the contract permanently. The customer will be consulted. 7.3 We are entitled to claim payment for the performance already carried out pursuant to the contract in question before the circumstances constituting force majeure became evident. 7.4 We are also entitled to invoke force majeure if the circumstance giving rise to force majeure arises only after our performance should have been rendered. Art. 8 Liability. 8.1 Notwithstanding statutory provisions on liability and product liability from which no derogation is permitted and in accordance with legal rules of public order and good faith, we are not obliged to pay any compensation at all for damage, of any nature whatsoever, be it direct or indirect, including loss of profits, to items of moveable or immovable property and/or to persons, both as regards the customer and third parties. In accordance with the rest of this article, we are not under any circumstances liable for damage caused by improper use of the goods supplied or by use thereof for a purpose other than that for which they are suited, to be determined according to objective standards. Technical advice and information on the processing and application possibilities of products is provided to the customer on the basis of our best knowledge and the current state of the art, without giving rise to any obligation and without any liability on our part. 8.2 Our liability will be partially assessed in view of any product/commercial insurance we have. Notwithstanding the coverage thereof, our liability is always limited to the net invoice value of the goods supplied. 8.3 Compliance with the applicable obligations regarding warranties/complaints and/or payment by us or our insurer(s) of the assessed damage, will be deemed as complete compensation covering all that is due. The customer indemnifies us explicitly and fully from any further liability. Art. 9 Complaints. 9.1 Notwithstanding the provisions elsewhere in these standard terms, all complaints relating to the quality of the goods supplied, must be submitted to us in writing within eight days after hand-over, stating precisely the nature and basis of the complaints. Complaints regarding invoices must be submitted within eight days after the invoice date. 9.2 Complaints regarding hidden defects (i.e. defects not visible upon hand-over) must be submitted within no less than twelve months after delivery and within eight days after their discovery. 9.3 Following the expiry of these periods, the customer will be deemed to have given approval for the goods supplied and/or the invoice. In such cases, we will no longer be required to take complaints into consideration. 9.4 If we have found a complaint to be well-founded, we are obliged only to deliver the defective goods anew, without the customer being entitled to any additional compensation of any nature whatsoever. 9.5 The submission of a complaint will not under any circumstances free the customer from its payment obligations towards us. 9.6 Delivered goods can be returned only once our prior written approval has been granted, under conditions to be determined by us. Art. 10 Retention of property All goods delivered by us and remaining in the control or possession of the customer, remain our property, until full payment has been made of all that the customer owes us on any account whatsoever, also including future claims against the customer, inclusive of interest and costs (and in cases of delivery on account, until settlement of any balance payable by the customer) With respect to these goods, we also acquire the (joint) right of property, as security for all of our outstanding claims against the customer, as well as in respect of the goods regarding which our property right is lost as a consequence of treatment/processing, accession, specification or otherwise. The transfer will be deemed to constitute a non-possessory pledge on the goods, for which the customer now grants advance, irrevocable consent, for the value of the remaining outstanding claims The goods may be resold or used by the customer in the normal course of its business, but may not be given as collateral or serve as security for any claim of a third party. Art. 11 Payment Payment must be made on a net basis, in cash, upon delivery or hand-over, without any deduction or set-off being applied, or by means of payment into a bank or Postbank account specified by us, within thirty days after the invoice date, unless agreed otherwise. The value day specified on these bank/postbank statements is decisive and will therefore be deemed as the date of payment Each payment by the customer will in the first place go towards paying the interest due, as well as any collection costs incurred by us and/or administrative costs. The remainder will then be deducted from the longest outstanding claim In the event that the customer: a. is declared bankrupt, assigns its estate, requests a moratorium on payments and/or all or part of its property is placed under attachment; b. dies or is placed under curatorship; c. fails to fulfil any obligations by virtue of statute or these standard terms; d. fails to pay an invoice sum or part thereof within the set period; e. ceases or transfers its business or an important part thereof, including incorporating the business in a company, and/or changes the objectives of the business; we are entitled, simply by virtue of one of the listed circumstances arising, either to deem the contract to have been dissolved without any judicial intervention being required, or to demand full payment of any sum payable by the customer in relation to work carried out by us and/or goods delivered by us, immediately and without any warning and/or notice of default being required, and to revindicate goods supplied but not or not yet paid for, as our own property, in all cases without prejudice to our entitlement to payment of costs, damages and interest Once the payment period has expired without the sum payable having been paid, we are entitled to declare the contract dissolved, without notice of default or judicial intervention being required and we are also entitled to repossess or order the repossession of the goods supplied, in accordance with the provisions on Retention of Property. Art. 12 Interest and costs If payment has not been made within the period referred to in the previous article, the customer enters default by operation of law and, as of the due date, is liable to pay interest of 1.5% per month or part thereof, on the amount remaining outstanding All judicial and extra-judicial costs to be incurred, will be for the expense of the customer. The extra-judicial collection costs will be at least 15% of the sum payable by the customer.

37

38 JORC Industrial LLC River Road New castle, DE Tel: Fax: