Instructions for Use. A-dec 500 Assistant s Instrumentation. Model 551

Transcription

1 Instructions for Use A-dec 500 Assistant s Instrumentation Model 551

2

3 A-DEC 500 A SSISTANT S INSTRUMENTATION (MODEL 551) I NSTRUCTIONS FOR USE

4 Copyright 2010 A-dec Inc. All rights reserved. A-dec Inc. makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. A-dec Inc. shall not be held liable for any errors contained herein or any consequential or other damages concerning the furnishing, performance or use of this material. The information in this document is subject to change without notice. If you find any problems in the documentation, please report them to us in writing. A-dec Inc. does not warrant that this document is error-free. No part of this document may be copied, reproduced, altered, or transmitted in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without prior written permission from A-dec Inc. This document is intended to be used in conjunction with the equipment. Trademarks and Additional Intellectual Property Rights A-dec, the A-dec logo, A-dec 500, A-dec 300, Cascade, Cascade Master Series, Century Plus, Continental, Decade, ICX, ICV, Performer, Preference, Preference Collection, Preference ICC, and Radius are registered trademarks in the U.S. Patent and Trademark Office. Preference Slimline and reliablecreativesolutions are also trademarks of A-dec Inc. Certain touchpad symbols are proprietary to A-dec Inc. Any use of these symbols, in whole or in part, without the express written consent of A-dec Inc. is strictly prohibited. Comments and Feedback If you have any feedback or comments about this document, contact us at: A-dec Inc. Technical Communications Department 2601 Crestview Drive Newberg, OR USA Tel: Within USA/Canada Tel: Outside USA/Canada techcomm@a-dec.com Website: Regulatory Information The Regulatory Information and Specifications document is delivered with A-dec dental device equipment as mandated by agency requirements. If you need this information, please go to the Document Library at Intended Application This equipment/system is intended for diagnostic and therapeutic treatment of dental patients by licensed health care professionals. Product Service For service information, contact your local authorized A-dec dealer. To find your local dealer, go to IFUbk6

5 CONTENTS 1 Introduction... 1 About Your A-dec 551 Assistant s Instrumentation...1 Serial Number Basic Operation... 5 Power...5 Power On/Off Button...5 Master Toggle...5 Alternate Master Toggle Locations...6 Vacuum Instrumentation...6 Left/Right Conversion...7 Auto-Electric Holders...7 Positioning...8 Touchpad...8 Solids Collector...9 Limit Switch Adjustments and Maintenance...11 Syringe Flow Adjustment...11 Utilities...11 HVE and Saliva Ejector Asepsis...12 Heat Sterilization...12 HVE Tip Sterilization...13 Care & Asepsis Instructions...13 Touch and Transfer Surfaces...13 Waterline Treatment...13 Appendix: Warranty and Specifications...15 Warranty...15 Specifications...16 Minimum Air, Water, and Vacuum Service Requirements...16 HVE and Saliva Ejector Opening for Tips Rev D iii

6 A-dec 500 Assistant s Instrumentation Instructions For Use iv Rev D

7 INTRODUCTION 1 Thank you for choosing A-dec equipment. This guide contains basic operating instructions, adjustments, and maintenance for A-dec 551 assistant s instrumentation. About Your A-dec 551 Assistant s Instrumentation A-dec s standard assistant s instrumentation includes an autoclavable syringe, HVE, and saliva ejector. Optional instruments may include an additional HVE (see Figure 1). The solids collector is also a part of the assistant s instrumentation, located at the end of the assistant s instrumentation arm. The assistant s vacuum instruments are fully autoclavable and include a quick-disconnect feature for easy removal and cleaning. For an overview of component features and options covered in this guide, see Figure 2 on page 2. Figure 1. A-dec 551 Assistant s Instrumentation (shown with dual HVE option) Rev D 1

8 A-dec O Clock Systems Instructions For Use Figure 2. A-dec 551 Assistant Instrumentation Features B C D A E G F H Item Description Supporting Instructions For Use A Dual Holder (with dual HVE option) Refer to page 7 of this guide. B HVE Refer to page 6 of this guide. C Saliva Ejector Refer to page 6 of this guide. D Touchpad Refer to page 8 of this guide. E Autoclavable Syringe Refer to the A-dec Syringes Instructions For Use (p/n ). F Long Assistant s Arm Refer to page 8 of this guide. G Solids Collector Refer to page 9 of this guide. H Support Link Refer to page 10 of this guide Rev D

9 Introduction Serial Number When you inquire about service for your A-dec 551 Assistant s Instrumentation, please provide the serial number. The serial number tag is located underneath the assistant s arm (see Figure 3). Figure 3. Serial Number Location Figure 4. Serial Number Label Example A B (A) The REF number is the model number. (B) The first letter of the serial number indicates the month the product was manufactured. The first digit of the serial number is the year of manufacture (for example, B9 = February 2009). Table 1. Key to Month of Manufacture Letter Month Letter Month A January G July B February H August C March I September D April J October E May K November F June L December Rev D 3

10 A-dec O Clock Systems Instructions For Use Rev D

11 BASIC OPERATION 2 This section includes basic operating instructions for your A-dec vacuum instrumentation, which covers the HVE, saliva ejector, touchpad, and solids collector. For information on the operation and maintenance of A-dec s autoclavable syringe, please refer to the A-dec Syringes Instructions For Use (p/n ). Power There are two power source locations for the assistant s instrumentation: the power on/off button on the chair and the delivery system Master toggle. Power On/Off Button The power on/off button is located on the base of the chair (see Figure 5) and allows you to engage power or disengage power to the entire system. When the button is pressed in, the system has power. When the button is out, the system has no power. Figure 5. Chair Power Power On/Off Master Toggle The Master toggle is located on the right side of the delivery system and controls the utilities for the system, as well as other modules mounted to the chair (see Figure 6). Flip the toggle to turn the system on or off. Figure 6. Master Toggle Location Master Toggle Rev D 5

12 A-dec 500 Assistant s Instrumentation Instructions For Use NOTE To prolong the life of your equipment, turn off the Master toggle when the delivery system is not in use. Alternate Master Toggle Locations Depending on your configuration, the Master toggle may instead be located on the cuspidor, support center, or remote floor box. Vacuum Instrumentation How you activate the vacuum instrumentation depends on what type of vacuum system you have (see Table 2). Once the system vacuum is activated, the HVE and saliva ejector operate the same: simply lift the valve lever (see Table 2). Table 2. Vacuum Activation and Instrument Function Configuration HVE Activation Saliva Ejector Activation Central Vacuum Lift valve lever Lift valve lever Single-Operatory Vacuum; Auto- Electric Holders Lift instrument from holder, then lift valve lever Figure 7. HVE and Saliva Ejector Operation Lift instrument from holder, then lift valve lever Opening (for tip) Valve Valve Lever HVE Saliva Ejector The HVE and saliva ejector s quick-disconnect feature allows you to easily remove the valve body from the tubing for simple cleaning and sterilization Rev D

13 Basic Operation Left/Right Conversion The HVE and saliva ejector can easily be converted for right- or left-handed operation. To convert the HVE or saliva ejector to one side or the other, push the valve out of the HVE body by pressing on the small diameter side. Rotate the valve 180, then push it back into place. Figure 8. HVE and Saliva Ejector Left/Right Conversion Auto-Electric Holders Your assistant s instrumentation may include optional auto-electric holders that provide vacuum on/off switching. When the HVE or saliva ejector is lifted from an auto-electric holder, a switch in the holder activates the vacuum pump. When the instrument is placed back in the holder, the switch turns the vacuum off. If both the HVE and saliva ejector have ribbed tubing, then you have auto-electric holders. Figure 9. Auto-Electric Holders (shown with optional dual 15mm HVE) Ribbed HVE Tubing Rev D 7

14 A-dec 500 Assistant s Instrumentation Instructions For Use Positioning Your assistant s instrumentation is delivered from holders that pivot and rotate to improve positioning (see Figure 10). To independently adjust each holder position: 1. Pull holder slightly away from the adjacent one. 2. Rotate to the desired position and release (see Figure 10). Figure 10. Positioning Instrument Holders Step 1 Step 2 Touchpad A-dec 551 Assistant s Instrumentation includes an integrated touchpad that controls chair, cuspidor, and dental light functions. Your touchpad serves as a convenient handle, rotates for better visibility, and is either surf or white in color (see Figure 11). For complete instructions on touchpad operation, see the Instructions For Use that came with your delivery system. Figure 11. Standard Touchpads Standard Surf Standard White Note: Touchpad symbols are proprietary to A-dec Inc Rev D

15 Basic Operation Solids Collector The solids collector helps prevent solids from entering the central vacuum system. To ensure proper suction from the central vacuum and maintain proper treatment room asepsis, discard and replace the solids collector screen at least twice a week (see Figure 12). TIP For replacement screens, contact your authorized A-dec dealer and reference Pinnacle p/n Figure 12. Replace Solids Collector Screen Solids Collector Cap Solids Collector Screen To replace the solids collector screen: 1. Turn off vacuum or open the HVE control valve. 2. Remove the solids collector cap. 3. Remove the solids collector screen. 4. Discard the screen according to your local regulations. CAUTION Do not empty the screen into your cuspidor. Doing so could plug the drain. 5. Insert new screen in the collector and replace the cap Rev D 9

16 A-dec 500 Assistant s Instrumentation Instructions For Use Limit Switch If an object becomes lodged under the lower support arm as the chair is lowered, a limit switch will interrupt the chair base down motion and reverse the chair to prevent damage. NOTE Please follow standard patient care precautions when using the chair preset position functions Rev D

17 ADJUSTMENTS AND MAINTENANCE 3 Syringe Flow Adjustment Utilities For syringe water and air flow adjustments, refer to your A-dec Syringes Instructions For Use (p/n ). A-dec 500 utilities are located in the contoured floor box for chair-mounted systems or in the cabinet for cabinet-mounted delivery systems. To access the utilities, lift up the floor box cover or removable cabinet panel. The utilities include the air/water shutoff valves, filters, pressure pre-regulators, vacuum and gravity drains, as well as electrical outlets (see Figure 13). For information on adjusting and maintaining the utilities, please see the Instructions For Use that came with your delivery system. Figure 13. System Utilities (shown in floor box) Air Pressure Gauge Moisture Separator Pre-Regulator Knob Air Manual Shutoff Valve Vacuum Drain Duplex Outlet Water Manual Shutoff Valve Rev D 11

18 A-dec 500 Assistant s Instrumentation Instructions For Use HVE and Saliva Ejector Asepsis To clean the HVE and saliva ejector: 1. Turn off the vacuum before disconnecting the HVE or saliva ejector. 2. Remove the tip from the HVE or saliva ejector. 3. Remove the HVE or saliva ejector valve body by pulling it away from the tubing at the tailpiece. 4. Remove the control valve by pushing it out of the HVE or saliva ejector valve body. 5. Clean and rinse the valve body and control valve using a mild detergent, water, and the brushes that have been provided. Allow the instruments to dry completely. 6. Heat sterilize the valve body and control valve using a steam autoclave for at least 6 minutes at a dwell temperature of 134ºC (273ºF). 7. Apply a light coat of A-dec silicone lubricant on the O-ring seals of the control valve. CAUTION Use only silicone lubricant when lubricating instrumentation O-rings. Petroleum products will cause permanent damage to the O-rings. 8. Reinstall the control valve in the valve body, then reinstall the valve body on the tubing tailpiece. 9. Operate the HVE and the saliva ejector valves several times to verify that they rotate smoothly. Heat Sterilization High volume evacuators (HVE), saliva ejectors, and air/water syringes should be steam autoclaved after each use. The following protocol should be followed: HVE and saliva ejector Steam autoclave at 134 C (273 F), 6 minutes holding time, minimum. A-dec air/water syringe Steam autoclave at 134 C (273 F), 4 minutes holding time, minimum Rev D

19 Adjustments and Maintenance HVE Tip Sterilization After each use, heat sterilize the stainless steel HVE tips using a steam autoclave for at least 4 minutes at a dwell temperature of 134ºC (273ºF). If you are using disposable HVE and saliva ejector tips, be sure to replace them with new tips after each use. To clean a stainless steel HVE tip: 1. Remove the HVE tip from the HVE. 2. Clean and rinse the HVE tip using a mild detergent and water, then allow the tip to dry completely. 3. Sterilize the HVE tip using the recommended methods. NOTE Select a tip that is compatible with your HVE and saliva ejector opening. See HVE and Saliva Ejector Opening for Tips on page 16 for specifications. CAUTION Disposable HVE and saliva ejector tips are not sterilizable and should not be reused. Care & Asepsis Instructions Touch and Transfer Surfaces Touch surfaces are those areas that come into contact with hands and fingers and become potential cross-contamination points during dental procedures. Transfer surfaces are those surfaces that are contaminated by contact with instruments and other inanimate objects. A-dec recommends barrier protection for all applicable touch and transfer surfaces. When used, barriers must be FDA market-cleared barrier plastic. Cover-All barrier film or any other FDA market-cleared barrier film is suitable for this application. Refer to your national regulatory authorities for barrier recommendations specific to your location. Barrier plastics should be removed and discarded after each patient treatment. For recommendations on cleaning and chemical disinfection of touch and transfer surfaces (where barrier protection is not applicable or when barriers are compromised), please refer to the A-dec Equipment Asepsis Guide (p/n ). Waterline Treatment For recommended treatment of your dental unit waterlines, refer to the A-dec Self-Contained Water System Instructions For Use (p/n ) Rev D 13

20 A-dec 500 Assistant s Instrumentation Instructions For Use Rev D

21 APPENDIX: WARRANTY AND SPECIFICATIONS A Warranty A-dec warrants all products against defects in materials or workmanship for one year from time of delivery. A-dec s sole obligation under the warranty is to provide parts for the repair, or at its option, to provide the replacement product (excluding labor). The buyer shall have no other remedy. All special, incidental, and coincidental damages are excluded. Written notice of breach of warranty must be given to A-dec within the warranty period. The warranty does not cover damage resulting from improper installation or maintenance, accident or misuse. The warranty does not cover damage resulting from the use of cleaning, disinfecting or sterilization chemicals and processes. The warranty also does not cover light bulbs. Failure to follow instructions provided in the A-dec Instructions For Use (operation and maintenance instructions) may void the warranty. A-dec warrants A-dec dental chair cylinders, both lift and tilt for ten years from the date of purchase of the chair or the cylinder. This warranty is retroactive to A-dec chair cylinders already in the field. The warranty covers chair cylinders A-dec finds to have manufacturing irregularities. Stool cylinders are covered under A-dec s one-year warranty. No other warranties as to merchantability or otherwise are made. For service information, contact your local authorized A-dec dealer. Check with local codes and ADA (Americans with Disabilities Act) requirements for installation of this product. CAUTION Federal law restricts this device to sale by or on the order of a dentist, physician, or any other practitioner licensed by the law of the state in which he or she practices to use or order the use of this device Rev D 15

22 A-dec 500 Assistant s Instrumentation Instructions For Use Specifications Minimum Air, Water, and Vacuum Service Requirements Air: 2.50 scfm (70.80 l/min) at 80 psi (551 kpa) Water: 1.50 gpm (5.68 l/min) at 40 psi (276 kpa) Vacuum: 12 cfm ( l/min) at 8 inches of mercury (27 kpa) HVE and Saliva Ejector Opening for Tips A-dec Standard HVE: 0.435" ± 0.006" (11.05 ± 0.15 mm) A-dec 15 mm HVE: 0.592" (14.8 mm) A-dec saliva ejector: ± 0.006" (6.73 ± 0.15 mm) For electrical specifications, identification of symbols, and other regulatory requirements, refer to the Regulatory Information and Specifications document (p/n ) included with your equipment. NOTE Specifications are subject to change without notice. Some requirements may vary from country to country. For more information, contact your authorized A-dec dealer Rev D

23

24 A-dec Headquarters 2601 Crestview Drive Newberg, OR USA Tel: Within USA/Canada Tel: Outside USA/Canada Fax: International Distribution Centers A-dec United Kingdom EU Authorized Representative Austin House, 11 Liberty Way Nuneaton, Warwickshire CV11 6RZ England Tel: 0800 ADECUK (233285) Within UK Tel: +44 (0) Outside UK A-dec Australia Unit 8, 5-9 Ricketty Street Mascot, NSW 2020 Australia Tel: Within Australia Tel: +61 (0) Outside Australia ÍvÈ.Ç&#È.00DÎ Rev C Copyright 2010 A-dec Inc. All rights reserved.