MATERIAL SAFETY DATA SHEET P/Nno.: SDSID: 1/5 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING Application: For3D or metallographic replica For 3D or metallographic replica Container size: 50; 265 ml Supplier: Struers A/S Pederstrupvej 84 DK2750 Ballerup Tel: +45 44 600 800 Emergency telephone: Infotrac: 18005355053 Struers US: 14408710071 Responsible for safety data sheet authoring: SDS_info@dhigroup.com 2. HAZARDS IDENTIFICATION The product is not classified. Human health: May cause minor irritation on eye contact. Environment: The product is not expected to be hazardous to the environment. 3. COMPOSITION/INFORMATION ON INGREDIENTS The product contains: Trace of chloroplatinic acid impurity. %: CASNo.: EC No.: Chemical name: Hazard classification: Notes: 120 67762941 Polymethylvinylsiloxane 120 68037854 Polymethoxyvinylsiloxane 120 68037592 Polymethylhydrogenosiloxane 110 63148538 Polyorganosiloxane 110 11126220 2343680 Silicone oxide 110 25231383 Polyoxymethylene diacetate 110 60676860 2623738 Silica 110 68412566 2701957 Platinum, complexes 4. FIRSTAID MEASURES Inhalation: Unlikely route of exposure as the product does not contain volatile substances. Skin contact: Remove contaminated clothes and rinse skin thoroughly with water. Eye contact: Immediately flush with plenty of water for up to 15 minutes. Remove any contact lenses and open eyelids widely. If irritation persists: Seek medical attention and bring these instructions. Ingestion: Immediately rinse mouth and drink plenty of water. Keep person under observation. If person becomes uncomfortable seek hospital and bring these instructions. 66826
2/ 5 P/Nno.: 5. FIREFIGHTING MEASURES SDSID: Extinguishing media: Use fireextinguishing media appropriate for surrounding materials. Specific hazards: In case of fire, silica and oxide of carbon will be released. 6. ACCIDENTAL RELEASE MEASURES Personal precautions: For personal protection, see section 8. Environmental precautions: Avoid discharge into water courses or onto the ground. Methods for cleaning up: Dam and absorb spillage with sand, sawdust or other absorbent. For waste disposal, see section 13. 7. HANDLING AND STORAGE Safe handling advice: Avoid contact with eyes. Observe good chemical hygiene practices. Technical measures: Work practice should minimize contact. Technical precautions: Local exhaust is recommended. Technical measures for safe storage: No special precautions. Storage conditions: Store in tightly closed original container. Store at room temperature. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Engineering measures: An eye wash bottle must be available at the work site. Personal protection: Personal protection equipment should be chosen according to the the CEN standards and in collaboration with the supplier of the personal protective equipment. Hand protection: Risk of contact: Wear protective gloves. Eye protection: Risk of contact: Wear goggles/face shield. Environmental Exposure Controls: Not available. (*) 66826
3/ 5 P/Nno.: 9. PHYSICAL AND CHEMICAL PROPERTIES SDSID: Appearance: Odor: ph: Boiling point: Flash point: Explosion limits: Relative density: Solubility: Other data: Viscous liquid, black or blue slight odor not relevant not available >150 C not relevant 1.1 insoluble in water VOC (Volatile Organic Substances): 0 g/l 10. STABILITY AND REACTIVITY Stability: Stable under normal temperature conditions. Conditions/ materials to avoid: Temperatures above 200 C. Hazardous decomposition products: Reacts with metals forming heat and hydrogen gas, which may form explosive vapor/air mixture. Silica dust and oxides of carbon are released at temperatures above 200 C. 11. TOXICOLOGICAL INFORMATION Inhalation: Not relevant at normal room temperatures. When heated, corrosive and toxic vapors may be formed. Skin contact: Prolonged contact may cause redness and irritation. Eye contact: Splashes may irritate. Ingestion: No harmful effects expected in amounts likely to be ingested by accident. Specific effects: None known. Carcinogenicity: National Toxicology Program (NTP): No. I.A.R.C. Monographs: No. OSHA: No. 66826
4/ 5 P/Nno.: 12. ECOLOGICAL INFORMATION SDSID: Mobility: The product is insoluble in water and will sediment in water systems. Degradability: The degradability of the product has not been stated. Ecotoxicity: The product is not expected to be hazardous to the environment. Bioaccumulative potential: No data available on bioaccumulation. Other adverse effects: None known. 13. DISPOSAL CONSIDERATIONS Dispose of waste and residues in accordance with local authority requirements. Can be burned in a chemical incinerator equipped with an afterburner and scrubber. Cured product can be disposed of as nonhazardous waste. Waste from residues: EWCcode: 16 05 09 14. TRANSPORT INFORMATION The product is not covered by international regulation on the transport of dangerous goods (IMDG, IATA, ADR/RID). 15. REGULATORY INFORMATION Labelling: Based on information from the manufacturer regarding the chemical composition, the product is not liable to classification and labelling. NFPA Rating: Specific provisions: National regulation: TSCA: Listed. Europe/USA: This Safety Data Sheet has been prepared according to the EUregulation. 66826
5/ 5 P/Nno.: 16. OTHER INFORMATION SDSID: The user must be instructed in the proper work procedure and be familiar with the contents of these instructions. Corrosion: The compounds contain minimal levels of fluorine, chlorine, sulphur compounds and heavy metals, and are approved for use on stainless steel in nuclear plants. The materials are designed specifically to be compatible with stainless steels and other engineering alloys and not to compromise future corrosion behaviour should traces of replicas remain after replication. Hydrogen embrittlement: Free hydrogen atoms are not produced when the base and accelerator in RepliSet are mixed. Hydrogen embrittlement is not expected to occur. Heat treatment: The residual silicone film left by RepliSet replicas will not influence heat treatment processes. Silicone residues decompose at about 280ºC, mostly to silica dust and oxides of carbon, and the quantities involved are very small. The following sections contain revisions or new statements: 8. The (*) indicates the changes made with respect to the previous version. Approved by DHI. The information on this data sheet represents our current data and is reliable provided that the product is used under the prescribed conditions and in accordance with the application specified on the packaging and/or in the technical guidance literature. Any other use of the product which involves using the product in combination with any other product or any other process is the responsibility of the user. Made by DHI Centre for Environment and Toxicology, Agern Allé 5, DK2970 Hørsholm, Denmark. www.dhigroup.com. 66826