To create a new service for WAN port building ADSL connection with ISP: There are seven PVCs this ADSL Router has supported. User can ask or get what kind of PVCs your ISP provides. You might need to add more connection type for making your WAN port connect to ISP successful. For instance ->: Addition "RFC1483 routed" : a.) Go to configuration\wan connections\ Create a new service b.) ATM \ select "RFC1483 routed". After you click "Configure" button, there are "Description", "VPI", and VCI, Encapsulation method, Use DHCP, WAN IP address" and "mask" seven items needs configure. "Description": Name it for this "RFC1483 Routed", you can give it any kind of name which you want it representation this "RFC1483 Routed". "VPI", "VCI": Fill both "VPI" and "VCI" in number, which ISP has provides for RFC1483 route
channel. "Encapsulation method": choose one of LLC/SNAP or VcMux Depends on your ISP has provide to decide using "Use DHCP" to dynamic get an IP address or give a static IP address for the WAN port of this ADSL router. "Mask": Subnet mask for WAN port IP address. *** (If your choose "WAN IP address", please add an line of "Static Route" in Configure\Static Route. Please reference "Static Route" in the following of this manual for setting "Static Route.) c.) Finish above setting, you can see there is one more line be added in the "WAN port connection" list and name is "RFC 1483-1". d.)to active a Security line for complete above setting for making WAN port connection. Go to configuration\ security\security interfaces\ click "add interface"\ new interface setup\ Name->rfc1483-1; Interface type-> external. Then click "Apply". e.)there is one more lines be added in "Security Interface" list name is "RFC1483-1".
f.) Click "Enable NAT to Internal Interface" to active RFC1483 Route for WAN. g.) Remembering to save setting which you have done it.
Addition "PPPoA routed" : a.) Go to configuration\wan connections\ Create a new service b.) ATM \ select "PPPoA routed". After you click "Configure" button, there are "Description", "VPI", "VCI", "WAN IP Address", "Mask", "LLC header mode", "HDLC header", "No authentication", "PAP", "CHAP", "User Name" and "Password" items needs configure.
"Description": Name it for this "PPPoA Routed", you can give it any kind of name which you want it representation this "PPPoA Routed. "VPI", "VCI": Fill both "VPI" and "VCI" in numbers, which ISP has provides for PPPoA route channel. "WAN IP address": ISP provide static IP address. "Mask": Subnet mask for WAN port IP address. "Encapsulation method": choose one of LLC/SNAP or VcMux "WAN IP address": IF ISP has provided static IP address for the WAN port of this ADSL router. "Mask": Subnet mask for WAN port IP address. "No authentication": Depends on your ISP have provide, if you choose "No authentication", you don't have to fill those following items "User name and " Password". "PAP", "CHAP": Depends on ISP provide you can choose one of "PAP" or "CHAP". After choose "PAP" or "CHAP" you have to fill following items "User name and " Password". *** (After your fill in "WAN IP address", please add an line of "Static Route" in Configure\Static Route. Please reference "Static Route" in the following of this manual for setting "Static Route". ) c.) Finish above setting, you can see there is one more line is added in the "WAN port connection" list and name is "PPP-0". d.)active a Security line for complete above setting for making WAN port connection. Go to configuration\ security\security interfaces\ click "add interface"\ new interface setup\ Name->PPP-0; Interface type-> external. Then click "Apply".
e.) Add one more lines be added in "Security Interface" list name is "PPP-0". f.) Click "Enable NAT to Internal Interface" to active PPPoA Route for WAN. g.) Remembering to save setting which you have done it.
Example: 1. PPPoA connection. VPI= 0 ; VCI=35 2. Dynamic IP 3. Without user name and password. a.) Go to configuration\wan connections\ Create a new service b.) ATM \ select "PPPoA routed". After you click "Configure" button, there are "Description", "VPI", "VCI", "WAN IP Address", "Mask", "LLC header mode", "HDLC header", "No authentication", "PAP", "CHAP", "User Name" and "Password" items needs configure. "Description": Name it for this "PPPoA Routed", you can give it any kind of name which you want it
representation this "PPPoA Routed. "VPI", "VCI": Fill both "VPI" and "VCI" in numbers, which ISP has provides for PPPoA route channel. "WAN IP address": ISP provide static IP address. "Mask": Subnet mask for WAN port IP address. "Encapsulation method": choose one of LLC/SNAP or VcMux "WAN IP address": IF ISP has provided static IP address for the WAN port of this ADSL router. "Mask": Subnet mask for WAN port IP address. "No authentication": Depends on your ISP have provide, if you choose "No authentication", you don't have to fill those following items "User name and " Password". "PAP", "CHAP": Depends on ISP provide you can choose one of "PAP" or "CHAP". After choose "PAP" or "CHAP" you have to fill following items "User name and " Password". *** (After your fill in "WAN IP address", please add an line of "Static Route" in Configure\Static Route. Please reference "Static Route" in the following of this manual for setting "Static Route". ) c.) Finish above setting, you can see there is one more line is added in the "WAN port connection" list and name is "PPP-0". d.)active a Security line for complete above setting for making WAN port connection. Go to configuration\ security\security interfaces\ click "add interface"\ new interface setup\ Name->PPP-0; Interface type-> external. Then click "Apply".
e.) Add one more lines be added in "Security Interface" list name is "PPP-0". f.) Click "Enable NAT to Internal Interface" to active PPPoA Route for WAN.
g.) Remembering to save setting which you have done it.
Addition "PPPoA Bridge" : a.) Go to configuration\wan connections\ Create a new service b.) ATM \ select "PPPoA Bridge". After you click "Configure" button, there are "Description", "VPI", "VCI", "LLC header mode", "HDLC header", " No authentication", "PAP", "CHAP", "User Name" and "Password" ten items needs configure. "Description": Name it for this "PPPoA Bridge", you can give it any kind of name which you want it representation this "PPPoA Bridge". "VPI", "VCI": Fill both "VPI" and "VCI" in numbers, which ISP has provide for RFC1483 route channel. "HDLC header": Choose "off" or "On", depends on your ISP have provide. "HDLC header": Choose "off" or "On", depends on your ISP have provide. "No authentication" : Depends on your ISP have provide, if you choose "No authentication", you don't have to fill those following items "User name and " Password".
c.) Finish above setting, you can see there is one more line is added in the "WAN port connection" list and name is "PPP-0".
Addition "RFC1483 Bridged" : a.) Go to configuration\wan connections\ Creat a new service b.) ATM \ select "RFC1483 Bridged". After you click "Configure" button, there are "Description", "VPI", "VCI", "Eencapsulation method" four items needs configure. "Description": Name it for this "PPPoA Bridge", you can give it any kind of name which you want it representation this "PPPoA Bridge". "VPI", "VCI": Fill both "VPI" and "VCI" in numbers, which ISP have provide for RFC1483 Bridge. "Encapsulation method": choose one of LLC/SNAP or VcMux(null) c.) Finish above setting, you can see there is one more line be added in the "WAN port connection" list and name is "RFC1483-1".
Addition "IPoA routed": a.) Go to configuration\wan connections\ Create a new service b.) ATM \ select "IPoA routed". After you click "Configure" button, there are "Description", "VPI", "VCI", "Use DHCP", " WAN IP address" and "mask" items needs configure. "Description": Name it for this "IPoA Routed", you can give it any kind of name which you want it representation this "IPoA Routed". "VPI", "VCI": Fill both "VPI" and "VCI" in numbers, which ISP has provides for IPoA route channel. Depends on your ISP has provide to decide using "Use DHCP" to dynamic get an IP address or give a static IP address for the WAN port of this ADSL router. "Mask": Subnet mask for WAN port IP address. *** (If your choose "WAN IP address", please add an line of "Static Route" in Configure\Static Route. Please reference "Static Route" in the following of this manual for setting "Static Route". )
c.) Finish above setting, you can see there is one more line be added in the "WAN port connection" list and name is "IPoA-0". d.)active a Security line for complete above setting for making WAN port connection. Go to configuration\ security\security interfaces\ click "add interface"\ new interface setup\ Name->IPoA-0; Interface type-> external. Then click "Apply".
e.) Add one more lines be added in "Security Interface" list name is "IPoA". f.) Click "Enable NAT to Internal Interface" to active IPoA Route for WAN. g.) Remembering to save setting which you have done it.
Addition "PPPoE routed": a.) Go to configuration\wan connections\ Creat a new service b.) ATM \ select "PPPoE routed". After you click "Configure" button, there are "Discription", VPI", "VCI", "PPPoE Auto Connect", " WAN IP address", "mask", "Access Concentrator", "service name" and" User Idle Timeout (in minutes)" items needs configure. "Description": Name it for this "PPPoE Routed", you can give it any kind of name which you want it representation this "PPPoE Routed". "VPI", "VCI": Fill both "VPI" and "VCI" in numbers, which ISP has provides for PPPoE route channel. "PPPoA Auto Connect": choose disable or enable. "WAN IP Address": "WAN IP address": ISP provides static IP address. "Mask": Subnet mask for WAN port IP address. "Access Concentrator": Name of access concentrator, ISP provide. "User Idle Timeout (in minutes)": fill in a numbers that you wish auto-disconnected WAN connect after LAN user idle for a while. "HDLC header": Choose "off" or "On", depends on your ISP have provide. "HDLC header": Choose "off" or "On", depends on your ISP have provide. "No authentication": Depends on your ISP have provide, if you choose "No authentication", you don't have to fill those following items "User name and " Password". "PAP", "CHAP": Depends on ISP provide you can choose one of "PAP" or "CHAP". After choose "PAP" or "CHAP" you have to fill following items "User name and " Password".
*** (If your choose "WAN IP address", please add an line of "Static Route" in Configure\Static Route. Please reference "Static Route" in the following of this manual for setting "Static Route".) c.) Finish above setting, you can see there is one more line is added in the "WAN port connection" list and name is "PPP-0". d.)to Active a Security line for complete above setting for making WAN port connection.
Go to configuration\ security\security interfaces\ click "add interface"\ new interface setup\ Name->PPP-0; Interface type-> external. Then click "Apply". e.) Add one more lines be added in "Security Interface" list name is "PPP-0". f.) Click "Enable NAT to Internal Interface" to active PPPoE Route for WAN. g.) Remembering to save setting which you have done it.
Addition " VPN -> PPTP " : a.) Go to configuration\wan connections\ Creat a new service b.) ATM \ select "VPN-> PPTP". After you click "Configure" button, there are "Description", "VPI", "VCI" and "LAN-IP address" items needs configure. "Description: Name it for this "IPoA Routed", you can give it any kind of name which you want it representation this "IPoA Routed". "VPI", "VCI": Fill both "VPI" and "VCI" in numbers, which ISP has provides for IPoA route channel. c.) Finish above setting, you can see there is one more line is added in the "WAN port connection" list and name is "PPP-0".