The EvB Starter Kit The EvB 5.1 Starter Kit with microcontroller ATMega32 is one of the most advanced kits on the market. It was designed not only for the novices but also for more advanced users. Thanks to the ATMega32, You don't have to worry about the adaptation of ATMega8 projects because the only difference between ATMega32 and ATMega8 is the memory space and number of pins. Also, You don't have to worry about the programmer, because EvB 5.1 kit has its own, built-in programer. Another helpful feature is that the microcontroller pins are led out twice. The EvB 5.1 Starter Kit comes with significant number of peripheral components. Their control pins are led out and well descriped, so making desired project is easier, faster and more intuitional. The use of FT232 chip eliminated the restriction from the lack of the LPT port. The kit is seen as COM port under Windows and Linux. More information at: http://and-tech.pl/zestaw-evb-5-1/
The AVR microcontrollers programmer The AVRPROG MK II is an advanced programmer for the AVR family. With it's help, You will program every AVR microcontroller available on the market. Also, You can set their Fuse bits and Lock bits.the programmer works with every programming environment (like BASCOM or AVRDUDE). The AVRPROG MK II works under 32-bits and 64-bits system: Windows XP, Windows Vista, Windows 7. Supported interfaces: ISP, PDI, TPI. The programmer comes with a 50 cm long cable, its ends have 2x5pin IDC connector. More information at: http://and-tech.pl/avrprog-mkii/ The AVR PROG v3 is a compact AVR programmer. It supports the ISP interface. The programmer works in programming environments : BASCOM, AVRDUDE, AVR STUDIO. More information at: http://and-tech.pl/avrprog-mk-ii-eco/ The Phoenix programmer The Phoenix USB is a modified Phoenix 3,58/6Mhz. The modification was about swapping the RS232 port (COM port) with USB2.0 port. The programmer creates a virtual COM port in the system, thanks to it, Phoenix USB is compatible with all the existing programs. The programmer is supplied from the USB port. More information at: http://and-tech.pl/phoenix-usb/
The Modules The AND-ETH is a standalone ethernet controller based on the ENC28J60 chip. It uses the popular SPI (Serial Peripheral Interface). It has its own MAC address and implemented physical layer PHY (Physical Layer). The AND-ETH module comes with integrated RJ45 socket including isolation transformer and two LEDs to indicate the connection and data transmission. More information at: http://and-tech.pl/and-eth-v2/ The AND-Graph132 is a colorful LCD display module. It has 4096 colours and resolution of 132x132 pixels. The module also has a 5-way joystick (4 ways + 1 button) located on the board. Thanks to module's compact dimensions, AND-Graph132 can be used in many ways. More information at: http://and-tech.pl/and-graph132/
Arduino board The Anduino Leonard is a modified Arduino Leonardo, which is 100% compatible with the original. Besides the standard equipment, like microcontroller ATMega32u4, 16 MHz quartz resonator, microusb, supply socket, ICSP connector or RESET button, it also has 4 buttons and 6 LEDs. It is a great starter kit for learning microcontroller programing and electronics. Thanks to a great number of modules available on the market, We can expand Anduino Leonardo's features really fast. We also offer an Arduino course. More information at: http://and-tech.pl/anduino-leonardo/ Arduino shields The ARD RELAY SHIELD is an Arduino shield with 4 relays 10A (max 230V) controlled by I2C interface. Thanks to I2C address, We can connect up to 4 ARD RELAY SHIELDs (16 relays) to 2 Arduino pins. With the shield comes a sample program. The ARD LCD216 SHIELD is an Arduino shield with LCD display and 5 buttons. The LCD display has two rows of 16 characters. The buttons are connected with accordingly selected resistors, so You can control all of them with just one microcontroller's pin. The shield has also built-in potentiometer, with its help You can control the display's contrast.
The ARD MOTOR SHIELD is an Arduino shield with 2 buttons and motor controller with two channels (for 2 motors or 2 servos). With its help, You can also control one stepper motor. The shield is based on L293D chip, its max current per channel is 0.6A (1.2A at peak) and max supply voltage for motors is 36V. With its help, Your robot can start moving in just 5 minutes. The ARD PROTO SHIELD is an universal board for Arduino. The solder pads are metallised and accordingly placed to match the Arduino standard. With board comes 40 pins. Thanks to that, You can make Your own, individual Arduino shield easy and fast. The ARD SCREW SHIELD was designed for Arduino. Thanks to the screw connectors located on the board, You can easily connect wires to Arduino without the need to solder.