Limited One Year Warranty T&S warrants to the original purchaser (other than for purposes of resale) that such product is free from defects in material and workmanship for a period of one () year from the date of purchase. During this one-year warranty period, if the product is found to be defective, T&S shall, at its options, repair and/or replace it. To obtain warranty service, products must be returned to Installation and Maintenance Instructions T&S Brass and Bronze Works, Inc. Attn: Warranty Repair Department Saddleback Cove Travelers Rest, SC 0 Shipping, freight, insurance, and other transportation charges of the product to T&S and the return of repaired or replaced product to the purchaser are the responsibility of the purchaser. Repair and/or replacement shall be made within a reasonable time after receipt by T&S of the returned product. This warranty does not cover Items which have received secondary finishing or have been altered or modified after purchase, or for defects caused by physical abuse to or misuse of the product, or shipment of the products. Any express warranty not provided herein, and any remedy for Breach of Contract which might arise, is hereby excluded and disclaimed. Any implied warranties of merchantability or fitness for a particular purpose are limited to one year in duration. Under no circumstances shall T&S be liable for loss of use or any special consequential costs, expenses or damages. Some states do not allow limitations on how long and implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. Specific rights under this warranty and other rights vary from state to state. P/N: 0-00- Rev. Date: 0-- Drawn: TEH Checked: JRM 0-- Approved: JHB 0-- Pre-Rinse Spray Valve B-00 UK-00 B-00-C UK-0K B-00-J EB-00 B-0K EB-00-C B-0K-C EB-00-J B-0K-J EB-0K EB-0K-C EB-0K-J
Exploded View 0 0
PARTS KIT Grey Part Number Guide PARTS FOR ANY GREY T&S SPRAY VALVE Ring, Hold Down # Washer Body, Spray Valve Grey Handle Nut, Handle Screw, Handle 0000-00- 0000-0 000-00- 00- PARTS FOR ANY GREY BONNET ASSEMBLY 0 Bonnet Assembly Stem Washer, Seat Washer, Bonnet Binding Bonnet Washer, Bonnet Brass Stem, Packing Spring, Bonnet Push Button Grease Pack 00-0 000-0 0-0000- 0000-000- 0000-000- 000-0- GREY SPRAY VALVES 0 B-00 (. GPM) Nipple Cup, Spray Ring, Sprayhead. GPM Sprayface Screw, Sprayface B-00-C (0. GPM) Assembly, B-00C Spray Nozzle 0. GPM Grey Shield (No Outline Around Lettering) 0. GPM Spray Nozzle (0. Stamped on Face) B-00-J (.0 GPM) Assembly, B-00-J Spray Nozzle.0 GPM Grey Shield (Square Outline).0 GPM Spray Nozzle (.0 Stamped on Face) Nozzle Holder 000-0 0000-0 00-00- 000-00-0 00-0- # Parts included in B-0K # Parts included in B-0K-C # Parts included in B-0K-J
PARTS KIT Blue Part Number Guide PARTS FOR ANY BLUE T&S SPRAY VALVE Ring, Hold Down # Washer Body, Spray Valve Blue Handle Nut, Handle Screw, Handle 0000-00- 0000-0 0-00- 00- PARTS FOR ANY BLUE BONNET ASSEMBLY 0 Bonnet Assembly Stem Washer, Seat Washer, Bonnet Binding Bonnet Washer, Bonnet Brass Quad Seal Spring, Bonnet Push Button Grease Pack 00-0 000-0 00-00- 0000-000- 0-000- 000-00- BLUE SPRAY VALVES,, 0 0 EB-00 & UK-00 Only Nipple Cup, Spray Ring, Sprayhead Screw, Sprayface EB-00 (- GPM) - GPM Sprayface (No Wording on Face) UK-00 (. GPM). GPM Sprayface (Flow Rate on Face) EB-00-C (0. GPM) Assembly, EB-00C Spray Nozzle 0. GPM Blue Shield (No Outline Around Lettering) 0. GPM Spray Nozzle (0. Stamped on Face) EB-00-J (.0 GPM) Assembly, EB-00-J Spray Nozzle.0 GPM Blue Shield (Square Outline).0 GPM Spray Nozzle (.0 Stamped on Face) Nozzle Holder 000-0 0000-0 0-000- 0-0- 0-0- # Parts included in EB-0K # Parts included in EB-0K-C # Parts included in EB-0K-J # Parts included in UK-0K
To replace worn parts: General Instructions. Shut off water supply and drain lines. For ease of disassembly and reassembly, the handle grip can be removed from no... Unscrew no. and no. to remove no.. Unscrew and remove no. from no... Hold no.0 with pliers in one hand, and with screwdriver, carefully unscrew no. from no.. 0. For EB-00/UK-00 & B-00 ONLY: To replace no., unscrew no. and disassemble. Make sure the groove side of no. fits over no., and no.0 rest on ridge side. See Figure A.. To replace no., unscrew handle grip from no. and replace with new no.. 0. Reassemble; turn on water check for leaks. Figure A 0 handle grip. Apply no. over smooth portion of no.. Replace no., no., no., no. & no. with new parts. Dab no. onto valve side of no. before replacing. 0 apply no. here. For EB-00-C, EB-00-J, B-00-C & B-00-J ONLY: To replace no., slide no. off no., and slide a new no. back onto no.. No. will snap into groove on no.. See Figure B. * Verify the flow rate on no. matches spray tip inside no.. Figure B. Reassemble no. by inserting no. through all parts. Hold no.0 with pliers, and carefully screw no. into no.0 until screw feels tight. Do not use excessive force.. Reinsert no. in no. and tighten securely.. Reassemble no., no. and no. on no.. Caution: Turn off water supply at base faucet when not in use.
RELATED T&S BRASS PRODUCT LINE B-00 JeTSpray Spray Valve B-00-C JeTSpray Low Flow Spray Valve T&S BRASS AND BRONZE WORKS, INC. A fi rm commitment to application-engineered plumbing products Saddleback Cove, P.O. Box 0, T & S Brass-Europe Travelers Rest, SC 0 De Veenhoeve Phone: () -0 Oude Nieuwveenseweg Fax: () - CW Nieuwveen E-mail: tsbrass@tsbrass.com The Netherlands