conga-qkit/iot Starter Kit for Qseven IoT Gateway Development Hardware Quick Start Guide Copyright 0 congatec AG QKIT_IoTq /
Preface Kit Contents This guide gives a brief overview of the conga-qkit/iot and how to quickly install, configure and operate it. For more information about the conga-qkit/iot, refer to the conga-qkit/ IoT datasheet and the User s Guide on the congatec website. congatec USB stick with OS image 7 TFT touch display Optional cable set (USB, audio) ESD Precaution All congatec AG products are electrostatic sensitive devices and are packaged accordingly. Do not open or handle a congatec AG product except at an electrostatic free workstation. Additionally, do not ship or store congatec AG products near strong electrostatic, electromagnetic, magnetic, or radioactive fields unless the device is contained within its original manufacturer s packaging. Be aware that failure to comply with these guidelines will void the congatec AG Limited Warranty. Product Overview The conga-qkit/iot - a congatec Qseven IoT Development Kit consists of: congatec s conga-qa/e87 module with suitable heatspreader Full featured Qseven IoT carrier board, 7 TFT touch display, Mini PCIe WLAN card and WLAN antenna with cable USB touch controller V Power supply USB stick pre-installed with demo Operating System Image. Set of cables for adequate setup. The conga-qa/e87 module features the Intel Atom E87 dual core processor with.7 GHz frequency, high definition graphics, GB dual channel DDRL- memory and onboard GB emmc. With maximum 8W TDP processor, the conga-qkit/iot offers an Ultra Low Power board with high computing performance and outstanding graphics. WLAN antenna with cable conga-qa/e87 conga-qa/hsp-b conga-enuc/qseven IoT carrier board Contents Description PN. No Name Description Qty 077600 conga-qkit/iot IoT Kit based on Intel Atom E87 processor. Supports Windriver IDP and build OS. 07760 conga-enuc/qseven IoT Evaluation board for QSeven IoT modules 00 conga-qa/e87 Qseven module with Intel Atom processor, GB dual channel memory and GB emmc flash. 09 conga-qa/hsp-b Standard conga-qa heatspreader. 00008 WLAN mini-pcie card Intel 760.HMWG (WiFi, Bluetooth). 00009 WLAN Antenna 80.ac/a/b/g/n dbi Omnidirectional Joint. 0000 QKIT/IoT Power Supply 0W, V@6A Power supply. (C power cord not included) 0000 Touch Controller TSC-/RU-F Touch controller board for the 7 TFT Display 0000 WLAN pigtail cable 0cm RP-SMA WLAN pigtail cable. 0009 cab-esatap to pin. SATA Cable with powered esata connector on one end and SATA connector on the other end 0000 cab-qkit/iot DC-IN 60mm DC-IN adapter cable for QKIT/IoT. 000 cab-qkit/iot LVDS conga-qkit/iot LVDS cable. Used for ATM0700L6E display (7 TFT display) 0008 cab-qkit/iot TSC-/RU conga-qkit/iot USB touch controller cable. 0009 QKIT/IoT Cable Set (Optional) Cable set. Contains USB and audio cables. N.A 00007 LCD Panel 7 TFT 800x80 display with resistive touch. 0000 congatec USB Stick 8 GB USB stick with pre-installed IoT OS image. 60000 Intel SK0 Trial Licence 90 day trial licence for Wind River IDP Quick Start Guide conga-qkit/iot Quick Start Guide Intel mini-pcie (WLAN) USB touch controller Power supply Copyright 0 congatec AG QKIT_IoTq /
Hardware Setup Touch Controller PN: 0000 conga-qkit/iot Interfaces and Functionality Overview Top Side Display Cable PN: 00007 SIM Slot WLAN Pigtail Cable PN: 0006 Touch Controller Cable PN: 0008 LVDS EDID EEPROM DC_IN Adapter Cable PN: 0006 LVDS Cable PN: 000 PWR ) (NC) GND +V TPM./.0 Qseven Module Connector Internal Display (LVDS, Backlight...) V Power Supply PN: 0000 conga-enuc/qseven IoT (PN: 07760) + Qseven Module (PN: 00) + Heatspreader (PN: 09) Bottom Side DisplayPort USB.0 esata Gbit Ethernet Steps: Attach the conga-qa Qseven module to the conga-enuc/qseven IoT evaluation board. Install the congatec heatspreader or an appropriate conga-qa cooling solution. Connect the twin connector end of the LVDS cable to the evaluation board (LVDS & backlight) and the single connector end to the display panel. Connect one end of the touch controller cable to the USB header on the evaluation board (bottom side) and the other end to the display panel. Connect other required peripherals. Plug in one end of the DC_IN adapter cable to the V power supply. To power on the system, plug in the other end of the DC_IN adapter cable to the evaluation board. msata module Encrypted EEPROM Speaker Sentinel HL CR 0 Battery HSPA/LTE or I/O module ) Audio MIC/HP Wifi + BT module ) RESET, FAN Copyright 0 congatec AG QKIT_IoTq /
Internal Interfaces (Top Side) LVDS (out) Backlight (out) 6 SIM Card Slot Power-IN 0 0 Backlight Voltage (only for >V rails) Backlight LVDS_A0-6 LVDS_B+ LVDS_A0+ 7 DGND LVDS_A- 8 LVDS_B- LVDS_A+ 9 LVDS_B+ LVDS_A- 0 LVDS_BCLK- 6 LVDS_A+ LVDS_BCLK+ 7 DGND LVDS_B- 8 LVDS_ACLK- LVDS_B+ Always on Ext. Backlight_VCC Switched Ext. Backlight_VCC 6 DGND 7 8 9 LVDS_ACLK+ DGND 9 Always on LVDS 0 LVDS_A- VCC (V) LVDS_A+ 6 VCC (V) 0 Int. Backlight_VCCV Qseven Module Connector LVDS_B0-7 VCC (V) Switched LVDS_B0+ 8 VCC (.V) Int. Backlight_VCCV DGND 9 VCC (.V) BL_Enable (ONN/OFF#) (.V) LVDS_B- 0 VCC (.V) BL DIMM Control (PWM) (..V) 6 DGND Fan DF9G-0P-H Hirose (max. A/pin with AWG8) 7 8 Do not connect Power-IN V Single Supply Fan (temp. controlled) Backlight (for non V) 9 Reserved (Programming Interface) 0 VCCV DGND DF9G-0P-H Hirose (max. A/pin with AWG8) Not connected DGND MC./-G-. Phoenix VCCV TACHO_IN (0 PU) Ext. Backlight_VCC IN (max V) DGND 6 SIM Card Slot Reverse voltage protection is implemented. Fuse and line filter have to be implemented externally. Use Phoenix FMC./-ST-. to connect power cord. Connection method: Spring-cage connection. PWM_OUT (V) 98-07 Molex Pin has internal 0k PU to VCCV. Only one fan connector (top or bottom) at a time can be used. Ext. Backlight_VCC switched Only used if Backlight_VCC can not be driven from internal VCCV (max. input V/A). Signals are connected to mini PCIe full size socket (contacts on top side). Copyright 0 congatec AG QKIT_IoTq /
Internal Interfaces (Bottom Side) Audio (MIC, Headphone) Speaker (Left/Right) Speaker (R/L) Audio (MIC, Headphone) Wifi + BT module AGND HP_OUT Left HP_OUT Right AGND SENSE_HP_OUT# (HP active when pin is connected to AGND) OUT+ OUT- x 6-07 Molex CR 0 Battery 6 SENSE_MIC# (MIC active when pin 6 is connected to AGND) msata module 7 AGND 8 MIC_Left (MIC_MONO) or 8 Ohms and W max. output Power. HSPA/LTE or I/O module 9 MIC_Right 0 AGND Documentation and Drivers Reset 6-07 Molex The conga-qkit/iot software documentation can be found here: www.congatec.com/conga-qkitiot FAN USB USB You can also find the conga- QA documentation here: FAN (Temp. Controlled) Reset VUSB (V, max. A) www.congatec.com/conga-qa USB_N USB_P DGND VCC_FAN (V, PWM) TACHO_IN (0K PU) 98-07 Molex RST# DGND 98-07 Molex DGND DGND x 98-07 Molex USB is not available if Sentinel HL Security Controller is assembled. The conga-qa drivers can be found in the restricted area of the congatec website. To gain access to the drivers, you must register. Contact your local congatec sales representative if you require assistance. Pin has internal 0k Pull-Up to VCCV. Copyright 0 congatec AG QKIT_IoTq /