Security System Standards

Security System Standards

Revision History Date Page Section Revision May 8, 2013 7 Mount Notes Added All exterior cameras shall be appropriately protected from lightning strikes. Security System Standards Oakland University Police Distribution: Restricted Publication Date: December, 2012 Review Date: May, 2013 Version: 1.5 Oakland University Police. All Rights Reserved. NOTICE: This document remains the property of the Oakland University Police Department. Its contents must not be copied or disseminated to any person, other than to a member of the OU Police, without the approval of OU Police Information Technology.

Table of Contents Introduction... 4 Video Surveillance Equipment... 5 Introduction... 5 Approved Cameras... 5 Outdoor Pendant Mount PTZ Camera... 5 Outdoor Ceiling Mount PTZ Camera... 5 Indoor Fixed Camera... 5 Indoor Ceiling Mount PTZ Camera... 6 Approved Mounts... 6 Rooftop Pendant Mount... 6 Wall Mount / Corner Mount / Pole Mount... 6 Mount Notes... 7 Power Supply for Exterior Non-PoE Cameras... 7 Surge Protector for Exterior Non-PoE Cameras... 7 Network Storage Manager... 7 Building Entrance Cameras (Placement)... 8 System Integration... 9 Camera Naming and Numbering... 9 Drawings and Plans... 9 Approved Camera Installations (Examples)... 10 Emergency Telephones... 11 Introduction... 11 Approved Phones... 11 Exterior Pedestal Phones... 11 Exterior Wall Mount Phones... 11 Interior Wall Mount Phones... 11 Emergency Phone Naming and Numbering... 12 Drawings and Plans... 12 Intrusion Alarm Equipment... 13 Introduction... 13 Access Control... 14 Introduction... 14 Networking Equipment... 15 Network Cabling... 15 Network Switches... 15 Patch Panels... 15 RJ45 Modules... 15 Fiber Modems... 15 Uninterruptable Power Supplies... 16 Introduction... 16 Emergency Responder Radio Coverage... 17 Introduction... 17 Standard... 17 Security System Standards 3

Introduction The Oakland University Police Department (OUPD) security system standards have been compiled for architects and engineers retained to provide professional services for Oakland University (OU). They include the planning, construction and maintenance standards of closed circuit television equipment, intrusion detection and notification equipment, access control equipment for police department facilities and emergency telephone equipment. These security system standards have been prepared so that reliable and consistent systems are constructed, thereby requiring minimal maintenance and operating expense. Adherence to these standards is required. Deviations must be reviewed with OUPD Information Technology prior to implementation. Equal or improved concepts, methods, or productions will be given full consideration when presented prior to implementation. The standards presented in this document should be followed in conjunction with OU s campus design standards. The images in this document are provided for illustrative purposes only. Please refer to product descriptions for specific information about each item. If an item outlined in these specifications is no longer available, please contact OUPD Information Technology to make a recommendation on a replacement product. Sections of this document will be revised and updated as experience of construction developments warrant. Each revised section supersedes all previous editions and directives concerning security system practices for OU. All questions should be directed to OUPD Information Technology at (248) 370-3407 or by email at helpdesk@oupolice.com. Security System Standards 4

Video Surveillance Equipment Introduction OU utilizes Pelco IP surveillance equipment with Pelco Endura as the video management system. Approved Cameras As a standard, the following cameras are approved for use on the campus of OU. Certain projects may require nonstandard or specialized camera models. Any deviation from these standards must be approved by OUPD Information Technology prior to implementation. Outdoor Pendant Mount PTZ Camera Spectra HD Series IP Dome (S5118-EG1) 1.3 Mpx, 18X optical zoom Environmental Pendant Mount Clear Lower Dome Grey or painted to match exterior colors. Outdoor Ceiling Mount PTZ Camera Spectra HD Series IP Dome (S5118-YB1) 1.3 Mpx, 18X optical zoom Environmental Ceiling Mount Clear Lower Dome Black with Black Trim Ring Indoor Fixed Camera IDE20 Series Sarix IP Indoor Fixed Dome (IDE20DN-0) 2.1 Mpx Smoked Lower Dome OUPD Approved Lenses: 13M2.8-12 Megapixel lens, varifocal, 2.8 ~ 12.0 mm 13M15-50 Megapixel lens, varifocal, 15.0 ~ 50.0 mm Security System Standards 5

Indoor Ceiling Mount PTZ Camera Spectra HD Series IP Dome (S5118-FW0) 1.3 Mpx, 18X optical zoom Ceiling Mount Smoked Lower Dome Black with White Trim Ring Approved Mounts Rooftop Pendant Mount 6 OU utilizes a modified rooftop mount from Moog Videolarm (SRCW2000). The heavy duty mount shall be installed as indicated based on the associated roof detail for flat roof installations. It should allow the camera to be raised above the roof line so service can be accomplished by rotating the unit in over the roof. The mount should be constructed of heavy gauge steel with 150 lb load rating. An associated extension arm for camera mounting should be modified as required to meet the design intent. The contractor shall coordinate with a local fabrication shop for all modifications necessary to meet the design intent while maintaining the full functionality of the mount including the rotation of the mount to allow for CCTV servicing and securing of the final position. The modified mounts shall be modified using like material and shall be painted with a powdercoat finish after fabrication/modification to match the housing of the camera. The rotating joint shall be covered with a 3 Fernco flexible coupling. The center of the camera dome shall extend a minimum of six inches beyond the roof line to allow the camera to view straight down. All modifications to roofs must be coordinated through and approved by OU Facilities Management. Surface mount conduit is not allowed on rooftops. Tie offs shall be provided at each camera location for servicing. Wall Mount / Corner Mount / Pole Mount IWM24-GY CM400 PA402 Security System Standards 6

Mount Notes All mounts should match the color of the camera housings selected. IWM24-GY mounts should only be used indoors if surface mounting options are not available. All exterior cameras shall be appropriately protected from lightning strikes. Power Supply for Exterior Non-PoE Cameras VertiLine 166 UL Listed CCTV Rack Mount Power Supply 16 fused power outputs Surge Protector for Exterior Non-PoE Cameras DITEK DTK-PVPIP Surge protectors should be mounted on a Middle Atlantic 2u flanged blank plate. The surge protectors should be mounted on the plate in a way that the flange wraps around the top and bottom of the surge protector. No more than 3 surge protectors should be mounted per blank plate. All surge protectors should be properly grounded. Network Storage Manger NSM5200 Projects with 14 or fewer cameras must include $1000 per camera storage fee. Projects with 15-20 cameras must include 1 NSM5200 unit. Projects with 21-40 cameras must include 2 NSM5200 units. Projects with 41-60 cameras must include 3 NSM5200 units. Projects with 61-80 cameras must include 4 NSM5200 units. If a project includes more than 80 cameras, contact OUPD Information Technology for storage calculations. Security System Standards 7

Building Entrance Cameras (Placement) All building entrances will be covered by a wall mounted fixed camera. The bottom of the dome should be mounted 72 above the finished floor. Entrance camera locations must be approved by OUPD Information Technology prior to installation. 72 above finished floor Security System Standards 8

System Integration Generally, the integration of cameras to the Endura system will be handled by OUPD Information Technology. Unless otherwise specified, the installing contractor will be responsible for the following: - The purchase and installation of approved cameras and/or equipment in accordance with these standards. - Provide power and networking to each camera location in accordance with these standards. - Notify OUPD Information Technology once cameras are installed and punched down in patch panels. - Label panels with the camera numbers provided by OUPD Information Technology. - Provide OUPD Information Technology with a list of device MAC addresses for integration into the camera network and also provide MAC addresses on the as-built drawings. Once the above is complete, OUPD Information Technology will: - Test each camera for functionality. A list of camera malfunctions or other issues will be provided to the installing contractor for correction. A representative of the installing contractor may accompany OUPD Information Technology during this process. - Configure all camera settings. - Authorize all MAC addresses on the camera network. - Focus and position all cameras. Camera Naming and Numbering Cameras will be named and numbered by OUPD Information Technology. To avoid confusion, all documentation regarding cameras shall utilize these names and numbers. Camera ports on patch panels should be labeled with the camera number. Drawings and Plans Once all camera locations have been determined, the architect shall provide OUPD Information Technology with a set of building plans in.pdf format indicating the location of each camera. These drawings should reflect the camera numbering provided by OUPD Information Technology. These plans will be used to present the camera locations to the Surveillance Review Panel. The installation of cameras should not commence until the plans are approved by the Surveillance Review Panel. At the conclusion of a construction project, a final set of drawings (as builts) shall be provided to OUPD Information Technology in.pdf and CAD format outlining the location of all surveillance equipment. Security System Standards 9

Approved Camera Installations (Examples) Security System Standards 10

Emergency Telephones Introduction OU utilizes Code Blue equipment for interior and exterior emergency telephones. All equipment should be IP based and able to integrate with ToolVOX Media Gateway. All phone locations must be approved by OUPD Information Technology. Approved Phones Exterior Pedestal Phones PAS 1-D Enclosure FP1 Faceplate Gloss Black Finish Emergency in White Letters Placement: As determined by OUPD Information Technology. Exterior Wall Mount Phones PAS 2-E Enclosure FP1 Faceplate Brushed Stainless Steel Emergency in White Letters Placement: Stairwell doors on every level in parking structures. Other locations as determined necessary by OUPD Information Technology. Interior Wall Mount Phones CB 4-S Enclosure FP1 Faceplate High Gloss Black Emergency in White Letters Placement: Non Residential Buildings - Inside stairwells (near the stairwell door) on every floor. - Every elevator lobby area. Residential Buildings - Every elevator lobby area. - Near stairwell doors (on the living area side of the door) on every floor. - Common areas (unless an elevator lobby phone is near by). Other locations as determined necessary by OUPD Information Technology. Security System Standards 11

Emergency Phone Naming and Numbering Emergency phones will be named and numbered by OUPD Information Technology. To avoid confusion, all documentation regarding emergency phones shall utilize these names and numbers. Emergency phone ports on patch panels should be labeled with the emergency phone number followed by a (EP) for emergency phone. Drawings and Plans The installation of emergency phones should not commence until the plans are approved by OUPD Information Technology. At the conclusion of a construction project, a final set of drawings (as builts) shall be provided to OUPD Information Technology in.pdf and CAD format outlining the location of all emergency phone equipment. Security System Standards 12

Intrusion Alarm Equipment Introduction OU utilizes Siemens SiPass for intrusion detection and notification. Security System Standards 13

Access Control Introduction Access control for all facilities except OUPD facilities is handled by the ID Card Office. For more information, contact: Don Ritenburgh Manager, ID Card Operations (248) 370-2533 ritenbur@oakland.edu OUPD utilizes Siemens SiPass for all access control for police facilities. Security System Standards 14

Networking Equipment Introduction Under normal circumstances, networking infrastructure will already be installed and available at the start of a security systems project. The following equipment shall be utilized in all other instances. Network Cabling All security system networking wiring shall be yellow CAT6A. Network Switches Cisco Catalyst 3750X 24 Port PoE LAN Base Cisco Catalyst 3K-X 1G Network Module Patch Panels New patch panels should match the existing panels in the network closet. For closets that use angled patch panels: Panduit CPPLA24WBLY (24 port) or CPPLA48WBLY (48 port) For closets that use flat patch panels: Panduit CPPL24WBLY (24 port) or CPPL48WBLY (48 port) RJ45 Modules Panduit Mini-Com modules (CJ688TGYL) yellow, CAT6A, RJ45 Fiber Modems GE Security S714D-EST2 Single Mode Available in standalone and rack mount configurations. See attached spec sheet for configuration options. Security System Standards 15

Uninterruptable Power Supplies Introduction Most OUPD projects will not include UPS since existing network infrastructure does not have UPS protection. If UPS protection is requested for a project, the below models should be used. Liebert GXT3, 500VA - 3000VA. All UPS equipment should include the network interface for remote management. Security System Standards 16

Emergency Responder Radio Coverage Introduction All buildings shall have approved radio coverage for emergency responders based upon the public safety communication system(s) of the Police/Fire/EMS agencies having jurisdiction at the exterior of the building. This standard shall be met without improvement or modification of the existing communications system infrastructure. Standard The building shall be considered to have acceptable emergency responder radio coverage when signal strength measurements in 95 percent of all areas on each floor of the building meet the signal strength requirements outlined below. A minimum signal strength of -90 dbm shall be receivable within the building as well as be receivable by the agency s radio system when transmitted from within the building. The dbm abbreviation represents a measured power level stated in decibels relative to 1 milliwatt (mw) and indicates the strength of the signal as compared to 1 mw. Contact OUPD Information Technology at (248) 370-3407 or by email at helpdesk@oupolice.com for assistance with signal strength testing or for in building radio enhancement options. Security System Standards 17

PRODUCT SPECIFICATION camera solutions Spectra HD Series IP Dome System HIGH DEFINITION PAN/TILT/ZOOM HIGH-SPEED DOME Product Features Up to 1280 x 960 Resolution 4:3 or 16:9 Aspect Ratio; 960p at 20 Images per Second (ips), 720p at 30 ips 1.3 Megapixel (MPx), 18X Optical, Wide Dynamic Range (WDR) Camera Ability to Control and Monitor Video Over IP Networks Built-in Analytics Including AutoTracking and Adaptive Motion Detection 2 Simultaneous Video Streams: Dual H.264 and Scalable MJPEG 360 Continuous Pan Rotation at 400 per Second Supported Protocols: TCP/IP, UDP/IP (Unicast, Multicast IGMP), UPnP, DNS, DHCP, RTP, NTP, and More Power over Ethernet (PoE) IEEE 802.3af USB Expansion Slots for Alarms and Audio Accessories Network Dome System Pelco takes its industry-leading Spectra Series dome into the world of high definition. Spectra HD delivers crystal-clear, live streaming images over the Internet using a standard Web browser (Microsoft Internet Explorer or Mozilla Firefox ). With four times the resolution of standard definition domes, Spectra HD is an ideal solution to view details such as faces, license plates, tattoos, playing cards (in casinos), or other specific features. Spectra HD supports High-Profile H.264 compression, a vast improvement in quality over MPEG-4 and 20 times more efficient than M-JPEG. The dome system features open architecture connectivity for third-party software recording solutions allowing integration into virtually any IP-based HD system. It is also compatible with Digital Sentry video management systems. As with all Pelco IP camera solutions, Spectra HD is Endura Enabled to record, manage, configure, and view multiple live streams. When connected to an Endura HD network-based video security system, the dome system has access to EnduraStor and EnduraView for optimized image quality and bandwidth efficiency. Spectra HD features the same ease of installation and ease of maintenance that you have come to expect from Spectra. Each dome system consists of a back box, a dome drive, and a lower dome. Spectra HD includes a choice of four back box models: in-ceiling, environmental in-ceiling, pendant, and environmental pendant. All environmental models meet NEMA Type 4X, IP66 when properly installed. 16 Preset Tours, 255 Dome Presets, 8 Privacy Zones Open IP Standards ONVIF v1.02 Conformant Built-In Analytics Pelco Analytics enhance the flexibility and performance of Spectra HD. Eight Pelco behaviors are preloaded and included as standard features. Pelco behaviors can be configured and enabled using a standard Web browser, and they are compatible with Endura or a third-party system that supports alarms using Pelco s API. Web Interface Spectra HD uses a standard Web browser for powerful remote setup and administration. Window Blanking Window blanking is used to conceal user-defined privacy areas that cannot be viewed by an operator. Spectra HD supports up to eight blanked windows. A blanked area will appear on the screen as a solid gray window. Video Systemization Spectra HD easily connects to Pelco IP and hybrid systems such as Endura version 2.0 (or later) and Digital Sentry version 7.3 (or later). The camera is also compatible with Digital Sentry NVs (DS NVs), a full-featured video management software, which is available as a free download atwww.pelco.com. DS NVs includes four free Pelco IP licenses and allows for the management of video from up to 64 cameras. Spectra HD features open architecture connectivity to third-party software. Pelco offers an application programming interface (API) and software developer s kit (SDK) for interfacing with Pelco's IP cameras. International Standards Organization Registered Firm; ISO 9001 Quality System C3470 / REVISED 3-21-12

TECHNICAL SPECIFICATIONS PELCO ANALYTICS Spectra HD Series includes eight user-configurable behaviors. The camera is capable of running up to three behaviors at the same time; although, the number of behaviors is limited to the available processing power of the camera and the type of analytic being used. Note: Available processing power is determined by the settings for compression standards, resolution, image rate, bit rate, and analytic configuration. For each behavior, you can create several custom profiles that contain different camera settings. With these profiles, you can set up different scenarios for the behavior, which will automatically detect and trigger alarms when specific activity is detected. Pelco Analytics are configured and enabled using a standard Web browser, and Pelco behavior alarms are compatible with Endura or a third-party system that supports Pelco s API system. Multiple Pelco behaviors can be scheduled to work during a certain time or condition. For example, during the day, a camera can be configured with Object Counting to count the number of people that enter a lobby door. At night, the operator can change the profile to Camera Sabotage to trigger an alarm if a camera is moved or obstructed. Available Pelco behaviors include: Abandoned Object: Detects objects placed in a defined zone and triggers an alarm if the object remains in the zone longer than the user-defined time allows. An airport terminal is a typical installation for this behavior. This behavior can also detect objects left behind at an ATM, signaling possible card skimming. Adaptive Motion Detection: Detects and tracks objects that enter a scene and then triggers an alarm when the objects enter a user-defined zone. This behavior is primarily used in outdoor environments with light traffic to reduce the number of false alarms caused by environmental changes. AutoTracking: Detects and tracks movement in the camera s field of view. When the AutoTracking behavior is configured, the system will automatically pan and tilt to follow the moving object until the object stops or disappears from the monitored area. Camera Sabotage: Detects contrast changes in the field of view. An alarm is triggered if the lens is obstructed with spray paint, a cloth, or a lens cap. Any unauthorized repositioning of the camera also triggers an alarm. Directional Motion: Generates an alarm in a high traffic area when a person or object moves in a specified direction. Typical installations for this behavior include an airport gate or tunnel where cameras can detect objects moving in the opposite direction of the normal flow of traffic or an individual entering through an exit door. Loitering Detection: Identifies when people or vehicles remain in a defined zone longer than the user-defined time allows. This behavior is effective in real-time notification of suspicious behavior around ATMs, stairwells, and school grounds. Object Counting: Counts the number of objects that enter a defined zone or cross a tripwire. This behavior might be used to count the number of people at a store entrance/exit or inside a store where the traffic is light. This behavior is based on tracking and does not count people in a crowded setting. Object Removal: Triggers an alarm if an object is removed from a defined zone. This behavior is ideal for customers who want to detect the removal of high value objects, such as a painting from a wall or a statue from a pedestal. Stopped Vehicle: Detects vehicles stopped near a sensitive area longer than the user-defined time allows. This behavior is ideal for airport curbside drop-offs, parking enforcement, suspicious parking, traffic lane breakdowns, and vehicles waiting at gates.

TECHNICAL SPECIFICATIONS The following diagram illustrates how the camera system interprets streaming video when embedded analytics are configured and enabled. SPECTRA VIDEO ANALYTICS OVERLAY CONFIGURATION ALARMS PELCO API SYSTEM IMPORTANT NOTE: PLEASE READ. The network implementation is shown as a general representation only and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the system as illustrated. Please contact your local Pelco Representative to discuss your specific requirements.

TECHNICAL SPECIFICATIONS SOFTWARE FEATURES 255 Presets 16 Tours ±0.1 Preset Accuracy Multilingual Menus (English, Spanish, Portuguese, Italian, German, French, Russian, Polish, and Turkish) Password Protection 400 /sec Pan Preset Speed and 200 /sec Tilt Preset Speed Rotating Discreet Liner with Sealed Fixed Bubble 8 Privacy Zones, Configurable in Size Auto Flip Feature Rotates Dome 180 at Bottom of Tilt Travel Configurable Park with Actions Proportional Pan/Tilt Continually Decreases Pan/Tilt Speeds in Proportion to Depth of Zoom BACK BOX FEATURES NOTE: VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS. 13.2 (5.2) 8.8 (3.5) 19.0 (7.5) 15.0 (5.9) 20.8 (8.2) In-Ceiling (Indoor) Single Back Box for Suspended or Hard Ceiling Applications Requires 13.35 cm (5.25 in.) Space Above Ceiling and 8.25 cm (3.25 in.) Below Minimum Ceiling Thickness 1.27 cm (0.50 in.); Maximum 4.45 cm (1.75 in.) Quick Disconnect to Dome Drive Aluminum Construction Suitable for Use in Environmental Air Handling Spaces (ENVIRONMENTAL DOME WITH SUN SHROUD SHOWN) 26.9 (10.6) 15.0 (5.9) 21.8 (8.6) Standard and Environmental Pendant Standard and Environmental Models Standard Pendant Available in Black or Gray Finish; Environmental Pendant Available in Gray Finish Only Quick Disconnect to Dome Drive Aluminum Construction Environmental Model Includes Sun Shield, Fan, and Heater 11.0 (4.4) 10.9 (4.3) 25.2 (9.9) 15.0 (5.9) 21.8 (8.6) Environmental In-Ceiling Single Back Box for Hard Ceiling Applications Requires 11.18 cm (4.40 in.) Space Above Ceiling and 10.92 cm (4.30 in.) Below Includes Heater and Fan Minimum Ceiling Thickness 1.27 cm (0.50 in.); Maximum 4.45 cm (1.75 in.) Quick Disconnect to Dome Drive Aluminum Construction

TECHNICAL SPECIFICATIONS CAMERA Sensor Type 1/3-inch CCD Optical Zoom 18X Maximum Resolution 1280 x 960 Lens f/1.6 (focal length, 4.7 ~ 84.6 mm optical) Aspect Ratios 4:3 or 16:9 Light Sensitivity f/1.6; 2,850 K; SNR >24dB Color (33 ms) 0.70 lux Color (250 ms) 0.07 lux Mono (33 ms) 0.25 lux Mono (250 ms) 0.02 lux Day/Night Capabilities Yes IR Cut Filter Yes IR Trace Curves 850 nm and 950 nm Wide Dynamic Range 60 db Iris Control Auto iris with manual override Backlight Compensation Yes VIDEO Video Encoding Video Streams Frame Rate H.264 High, Main, or Base profiles and MJPEG Up to 2 simultaneous streams; the second stream is variable based on the setup of the primary stream Up to 30, 25, 24, 15, 12.5, 12, 10, 8, 7. 5, 6, 5, 4, 3, 2.5, 2, 1 (dependent upon coding, resolution, and stream configuration) Available Resolutions Resolution MJPEG H.264 High Profile (IP GOP structure) MPx Width Height Aspect Ratio Maximum IPS Recommended Bit Rate (Mbps) Maximum IPS Recommended Bit Rate (Mbps) 1.30 1280 960 4:3 20 12.00 20 3.00 0.92 1280 720 16:9 30 12.00 30 2.90 0.49 800 608 4:3 20 5.15 20 1.75 0.31 640 480 4:3 20 3.25 20 1.20 0.23 640 352 16:9 30 3.60 30 1.15 0.18 480 368 4:3 20 1.85 20 0.75 0.13 480 272 16:9 30 2.05 30 0.75 0.08 320 240 4:3 20 0.80 20 0.40 0.06 320 176 16:9 30 0.90 30 0.35 Supported Protocols TCP/IP, UDP/IP (Unicast, Multicast IGMP), UPnP, DNS, DHCP, RTP, RTSP, NTP, IPv4, SNMP v2c/v3, QoS, HTTP, HTTPS, LDAP (client), SSH, SSL, SMTP, FTP, and 802.1x (EAP) Users Unicast Up to 20 simultaneous users depending on resolution settings (2 guaranteed streams) Multicast Unlimited users H.264 Security Access Password protected Software Interface Web browser view and setup Pelco System Integration Endura 2.0 (or later) Digital Sentry 7.3 (or later) Open API Pelco API or ONVIF v1.02 Minimum System Requirements Processor Intel Core 2 Duo microprocessor, 2.6 GHz Operating System Windows XP, Windows Vista, or Mac OS X 10.4 (or later) Memory 2 GB RAM Network Interface Card 100 megabits (or greater) Monitor Minimum of 1024 x 768 resolution, 16- or 32-bit pixel color resolution Web Browser* Internet Explorer 7.0 (or later) or Firefox 3.5 (or later); Internet Explorer 8.0 (or later) is recommended for configuring analytics Media Player Pelco Media Player or QuickTime 7.6.5 for Windows XP, Windows Vista, or QuickTime 7.6.4 for Mac OS X 10.4 ANALYTICS Required Systems for Pelco Analytics Pelco Interface WS5200 Advanced System Management Software on an Endura 2.0 (or later) system Open API The Pelco API can transmit behavior alarm data to third-party applications, available at pdn.pelco.com *Internet Explorer is not supported by Mac OS X 10.4. This product is not compatible with QuickTime version 7.6.4 for Windows XP or Windows Vista. If you have this version installed on your PC, you will need to upgrade to QuickTime version 7.6.5. Pelco Media Player is recommended for control, smoothness, and reduced latency as compared to QuickTime.

TECHNICAL SPECIFICATIONS GENERAL Construction Back Box Dome Drive Lower Dome Light Attenuation Smoked Clear Cable Entry (back box) In-Ceiling Aluminum Aluminum, thermo plastic Acrylic f/0.5 light loss Zero light loss 0.75-inch conduit fitting Pendant Through 1.5-inch NPT pendant mount Weight (approximate) Unit Shipping In-Ceiling 2.4 kg (5.2 lb) 3.6 kg (8 lb) Environmental In-Ceiling 2.8 kg (6.2 lb) 4.5 kg (10 lb) Standard Pendant 3.0 kg (6.5 lb) 5.0 kg (11 lb) Environmental Pendant 3.5 kg (7.6 lb) 5.4 kg (12 lb) Environment In-Ceiling Environmental In-Ceiling Pendant, Standard, and Environmental Operating Temperature In-Ceiling Standard Pendant Maximum Minimum Environmental In-Ceiling, Environmental Pendant Maximum Minimum Indoor Outdoor Indoor/outdoor 0 to 50 C (32 to 122 F) (Assumes no wind chill factor) 45 C (113 F) absolute maximum; 35 C (95 F) sustained maximum 4 C (25 F) sustained minimum (Assumes no wind chill factor) 60 C (140 F) absolute maximum; 50 C (122 F) sustained maximum 51 C ( 60 F) absolute minimum; prevents icing at sustained minimum of 30 C ( 22 F); de-ices 2.5 mm (0.1 in.) within 3 hours after power-up at 30 C ( 22 F) Effective Projected Area (EPA) 20.5 square inches (without mount), 47 square inches (with IWM Series mount) ELECTRICAL Ports Cabling Type Input Voltage RJ-45 connector for 100Base-TX Auto MDI/MDI-X Autonegotiate/Manual setting Cat5 or better for 100Base-TX 18 to 32 VAC; 24 VAC nominal 22 to 27 VDC; 24 VDC nominal Input Power 24 VAC 23 VA nominal (without heater); 73 VA nominal (with heater) 24 VDC 0.7 A nominal (without heater); 3 A nominal (with heater) PoE Fuse IEEE802.3af (without heater) 1.25 A MECHANICAL (Dome Drive Only) Variable Speed 0.1 to 400 Preset Accuracy ±0.1 Pan Movement 360 continuous pan rotation Vertical Tilt +0 to 90 Manual Pan/Tilt Speeds Pan 0.1 to 80 /sec manual operation, 150 /sec Turbo Tilt 0.1 to 40 /sec manual operation Preset Speeds Pan 400 /sec Tilt 160 /sec

TECHNICAL SPECIFICATIONS SYSTEM MODEL NUMBERS Type Back Box Color Lower Dome In-ceiling, indoor In-ceiling, environmental Pendant, standard Pendant, environmental Black with white trim ring Black with black trim ring Gray Black Gray Smoked Clear Smoked Clear Smoked Clear Smoked Clear Smoked Clear HD, 1.3 MPx, 18X Color S5118-FW0 S5118-FW1 S5118-YB0 S5118-YB1 S5118-PG0 S5118-PG1 S5118-PB0 S5118-PB1 S5118-EG0 S5118-EG1 COMPONENT MODEL NUMBERS Back Box Lower Dome* Dome Drive B5-F HD, in-ceiling, gray LDHQF-0 High-quality, smoked, in-ceiling D5118 HD, 1.3 Mpx, 18X optical zoom B5-F-E HD, environmental in-ceiling, gray LDHQF-1 High-quality, clear, in-ceiling B5-PG HD, pendant, gray LDHQPB-0 High-quality, smoked, pendant B5-PB HD, pendant, black LDHQPB-1 High-quality, clear, pendant B5-PG-E HD, environmental pendant, gray *Use the pendant lower domes with the environmental in-ceiling and environmental pendant back boxes. CERTIFICATIONS/RATINGS/PATENTS CE, Class A FCC, Class A UL/cUL Listed C-Tick U.S. Patents 5,931,432; 6,793,415 B2; 6,802,656 B2; 6,821,222 B2; 7,161,615 B2 Meets NEMA Type 4X and IP66 standards when installed properly (B5-F-E and B5-PG-E) ONVIF 1.02

TECHNICAL SPECIFICATIONS RECOMMENDED MOUNTS In-Ceiling Domes SD5-P 2' x 2' drop ceiling panel, aluminum construction; replaces 2'þx 2' ceiling tile SCA1 Support rails for B5-F; for use in ceiling tile applications Pendant Domes BB5-PCA-BK Pendant conduit adapter, black BB5-PCA-GY Pendant conduit adapter, gray IWM Series Wall mount, with or without integral 24 VAC, 100 VA transformer; black or gray finish; can be adapted for corner, parapet or pole application MRCA Ceiling mount, black PP4348 Parapet roof mount PP350/PP351 Parapet wall/roof mount SWM Series Compact wall mount, black or gray finish; can be adapted for corner or pole applications OPTIONAL ACCESSORIES ALM-1 External alarm accessory AUD-1 External audio accessory MCS Series Indoor, 24 VAC power supply WCS Series Outdoor, 24 VAC power supply Refer to individual power supply specifications for more information. Pelco by Schneider Electric 3500 Pelco Way, Clovis, California 93612-5699 United States USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. All other product names and services are the property of their respective companies. ONVIF and the ONVIF logo are trademarks of ONVIF Inc. Product specifications and availability are subject to change without notice. Copyright 2012, Pelco, Inc. All rights reserved.

PRODUCT SPECIFICATION camera solutions IDE20 Series Sarix IP Indoor Fixed Dome 2.1 MEGAPIXEL EXTENDED PLATFORM HIGH DEFINITION INTEGRATED CAMERA Product Features Up to 2.1 Megapixel Resolution (1920 x 1080) Up to 30 Images per Second (ips) at 1920 x 1080 Up to 30 Images per Second (ips) at 1920 x 1080 Using H.264 Compression Optional CS-Mount Lenses Auto Back Focus for High Precision Focusing Easy, Quick, One-Handed Installation H.264 and MJPEG Compression Day/Night Capability Sensitivity Down to 0.03 lux Power over Ethernet (IEEE 802.3af) or 24 VAC Video Setup Jack and Focus Button Accessible with Dome Closed Up to 2 Simultaneous Video Streams Built-in Analytics The Sarix IDE20 Series extended platform (EP) is a 2.1 megapixel (MPx) network indoor fixed dome camera designed with industry-leading image quality and high performance processing power. Designed to install quickly and easily, all of the post back-box installation and setup can be done with one hand. Sarix technology defines the next generation of video security imaging performance, delivering high definition (HD) resolution, advanced low-light capabilities, consistent color science, and fast processing power. The H.264 compression video files are considerably smaller, making HD video more affordable. Fixed Dome Camera The IDE20 Series can be ordered with or without lenses. All models include advanced low-light technology and a camera in an indoor enclosure that is ready to install. The day/night model has a mechanical IR cut filter for increased sensitivity in low-light installations. These cameras accept a wide range of megapixel varifocal CS-mount lenses. The IDE20 Series supports two simultaneous video streams. The two streams can be compressed in MJPEG and H.264 formats across several resolution configurations. The extended platform gives realtime video (30 ips) with full HD resolution using H.264 compression for optimized bandwidth and storage efficiency. The streams can be configured in a variety of frame rates, bit rates, and group of pictures (GOP) structures for additional bandwidth administration. The IDE20 Series is simple to install, and the automatic back focus control feature makes sharp scene focus setup easy. A convenient video setup jack eliminates the need to use a laptop for viewing video when installing the camera. Local Storage (Micro SD) for Alarm Capture Adaptive Motion Detection ONVIF v1.02 Conformant Audio Accessory Available Built-In Analytics Pelco Analytics enhance the flexibility and performance of the IDE20 Series camera. Eight Pelco behaviors are preloaded and included as standard features of the IDE20DN models. Pelco behaviors can be configured and enabled using a standard Web browser, and they are compatible with Endura or a third-party system that supports alarms using Pelco s API. Camera models are also available with preloaded OV Analytic Suites. Web Interface The IDE20 Series uses a standard Web browser for powerful remote setup and administration. Window Blanking Window blanking is used to conceal user-defined privacy areas that cannot be viewed by an operator. The IDE20 Series supports up to four blanked windows. A blanked area will appear on the screen as a solid gray window. Video Systemization The IDE20 Series easily connects to Pelco IP and hybrid systems such as Endura version 2.0 (or later) and Digital Sentry version 7.3 (or later). The camera is also compatible with Digital Sentry NVs (DS NVs), a full-featured video management software, which is available as a free download at www.pelco.com. DS NVs includes four free Pelco IP licenses and allows for the management of video from up to 64 cameras. The IDE20 Series features open architecture connectivity to thirdparty software. Pelco offers an application programming interface (API) and software developer s kit (SDK) for interfacing with Pelco s IP cameras. International Standards Organization Registered Firm; ISO 9001 Quality System C2964 / REVISED 5-17-12

TECHNICAL SPECIFICATIONS PELCO ANALYTICS The IDE20 Series includes eight user-configurable behaviors. The camera is capable of running up to three behaviors at the same time; although, the number of behaviors is limited to the available processing power of the camera and the type of analytic being used. Note: Available processing power is determined by the settings for compression standards, resolution, image rate, bit rate, and analytic configuration. For each behavior, you can create several custom profiles that contain different camera settings. With these profiles, you can set up different scenarios for the behavior, which will automatically detect and trigger alarms when specific activity is detected. Pelco Analytics are configured and enabled using a standard Web browser, and Pelco behavior alarms are compatible with Endura or a third-party system that supports Pelco s API system. Multiple Pelco analytics can be scheduled to work during a certain time or condition. For example, during the day, a camera can be configured with Object Counting to count the number of people that enter a lobby door. At night, the operator can change the profile to Camera Sabotage to trigger an alarm if a camera is moved or obstructed. Available Pelco behaviors include: Abandoned Object: Detects objects placed in a defined zone and triggers an alarm if the object remains in the zone longer than the user-defined time allows. An airport terminal is a typical installation for this behavior. This behavior can also detect objects left behind at an ATM, signaling possible card skimming. Adaptive Motion Detection: Detects and tracks objects that enter a scene and then triggers an alarm when the objects enter a user-defined zone. This behavior is primarily used in outdoor environments with light traffic to reduce the number of false alarms caused by environmental changes. Camera Sabotage: Detects contrast changes in the field of view. An alarm is triggered if the lens is obstructed with spray paint, a cloth, or covered with a lens cap. Any unauthorized repositioning of the camera also triggers an alarm. Directional Motion: Generates an alarm in a high traffic area when a person or object moves in a specified direction. Typical installations for this behavior include an airport gate or tunnel where cameras can detect objects moving in the opposite direction of the normal flow of traffic or an individual entering through an exit door. Loitering Detection: Identifies when people or vehicles remain in a defined zone longer than the user-defined time allows. This behavior is effective in real-time notification of suspicious behavior around ATMs, stairwells, and school grounds. Object Counting: Counts the number of objects that enter a defined zone or cross a tripwire. This behavior might be used to count the number of people at a store entrance/exit or inside a store where the traffic is light. This behavior is based on tracking and does not count people in a crowded setting. Object Removal: Triggers an alarm if an object is removed from a defined zone. This behavior is ideal for customers who want to detect the removal of high value objects, such as a painting from a wall or a statue from a pedestal. Stopped Vehicle: Detects vehicles stopped near a sensitive area longer than the user-defined time allows. This behavior is ideal for airport curbside drop-offs, parking enforcement, suspicious parking, traffic lane breakdowns, and vehicles waiting at gates. OBJECTVIDEO (OV) ANALYTIC SUITES ObjectVideo Analytics Suites are preloaded on selected IDE20 Series cameras and require an OV Ready system to configure the behaviors for alarm notification. OV Security Suite The OV Security Suite is easy to use and includes Tripwire Detection, Inside Area Detection, and Camera Tamper Detection behaviors. Tripwire Detection identifies objects that cross a user-defined line drawn within the camera s field of view. Inside Area Detection identifies objects entering, appearing, or moving within a user-defined area. Camera Tamper Detection identifies significant contrast changes in the camera s field of view; for example, if the lens is obstructed by spray paint, a cloth, or a lens cap. OV Security Suite Plus The OV Security Suite Plus includes the behaviors of the OV Security Suite, plus Multi-Line Tripwire Detection, Loitering Detection, and Leave Behind Detection behaviors. Multi-Line Tripwire Detection identifies objects that cross two defined lines and generates an event based on defined parameters, including directionality. Defined parameters for this behavior include direction, sequential order, and time between crossing each tripwire. Loitering Detection identifies when people or vehicles remain within a user-defined area beyond a specified period of time. This behavior is effective for real-time notification of suspicious behavior around ATMs, stairwells, and school grounds. Leave Behind Detection detects objects placed in a defined zone and triggers an alarm if the object remains in the zone longer than the user-defined time allows. OV Event Counting Suite The OV Event Counting Suite uses advanced object calibration and additional features for schedules, parameters, and multiple rules. The suite includes behaviors for Tripwire Counting, Enters/Exits Counting, Loiter Counting, Occupancy Sensing, and Dwell-Time Monitoring. Tripwire Counting counts people or objects that cross a user-defined line. Enters/Exits Counting calculates the number of people that enter and exit an area without using a tripwire. Loiter Counting is useful in analyzing how frequently people stop in front of a product, display, or other area of interest. This feature is also useful in assessing promotion effectiveness and product interest. Occupancy Sensing counts people and generates a new value every time the occupancy level changes. Since each occupancy output is timestamped, the data can be used to determine average occupancy levels or to correlate data to point-of-sale or other business scenarios. Dwell-Time Monitoring rules can be set up to record the length of time it takes an object to enter and exit an area. Along with queue size information, wait times can also be assessed. This behavior can be used to evaluate consumer interaction for a point-of-sale display or digital advertisement.

TECHNICAL SPECIFICATIONS The following diagram illustrates how the camera system interprets streaming video when embedded analytics are configured and enabled. SARIX VIDEO ANALYTICS OVERLAY CONFIGURATION ALARMS PELCO API / OV READY SYSTEM IMPORTANT NOTE: PLEASE READ. The network implementation is shown as a general representation only and is not intended to show a detailed network topology. Your actual network will differ, requiring changes or perhaps additional network equipment to accommodate the system as illustrated. Please contact your local Pelco Representative to discuss your specific requirements.

TECHNICAL SPECIFICATIONS GENERAL Imaging Device 1/3-inch (effective) Imager Type CMOS Imager Readout Progressive scan Maximum Resolution 1920 x 1080 Signal-to-Noise Ratio 50 db Auto Iris Lens Type DC drive Electronic Shutter Range 1 ~ 1/100,000 sec Wide Dynamic Range 60 db White Balance Range 2,000 to 10,000 K Sensitivity f/1.2; 2,850 K; SNR >24 db Color (1x/33 ms) 0.5 lux Color SENS (15x/500 ms) 0.12 lux Mono (1x/33 ms) 0.25 lux Mono SENS (15x/500 ms) 0.03 lux Dome Attenuation Clear Zero light loss Smoked f/1.0 light loss Construction Back Box Cast aluminum Trim Ring Polycarbonate plastic Bubble Acrylic plastic Finish White Weight (without lens) Unit 0.9 kg (2.0 lb) Shipping 2.7 kg (6.0 lb) Available Languages Chinese, English, French, German, Italian, Portuguese, Russian, Spanish, and Turkish ELECTRICAL Port RJ-45 connector for 100Base-TX Auto MDI/MDI-X Cable Type Cat5 or better for 100Base-TX Power Input 18 to 34 VAC; 24 VAC nominal or PoE (IEEE 802.3af class 3) Power Consumption <6 W Current Consumption PoE <200 ma maximum 24 VAC <295 ma nominal; <390 ma maximum Local Storage Micro SD Alarm Input 10 VDC maximum, 5 ma maximum Alarm Output 0 to 15 VDC maximum, 75 ma maximum Service Port External 3-connector, 2.5 mm provides NTSC/PAL video output Accessory Port Connects Pelco accessories NOTE: VALUES IN PARENTHESES ARE INCHES; ALL OTHERS ARE CENTIMETERS. IN-CEILING 8.50 (3.33) Ø 12.70 (5.00) SURFACE MOUNT (Mounting Ring Included) Ø 12.70 (5.00) 19.05 (7.50) 20.19 (7.95) PENDANT (Mount Available as Accessory) 19.63 (7.73) 7.52 6.93 (2.96) (2.73) 8.43 (3.32) 16.05 (6.32) MECHANICAL Lens Mount CS mount, adjustable Pan/Tilt Adjustment Pan 368 Tilt 160 (10 to 170 ) Rotate 355 ENVIRONMENTAL Operational Temperature Operational Humidity 0 to 50 C (32 to 122 F) 20% to 80%, noncondensing Ø 12.70 (5.00) 19.38 (7.63)

TECHNICAL SPECIFICATIONS VIDEO Video Encoding H.264 high, main, or base profile and MJPEG Video Streams Up to 2 simultaneous streams; the second stream is variable based on the setup of the primary stream Frame Rate Up to 30, 25, 24, 15, 12.5, 12, 10, 8, 7. 5, 6, 5, 4, 3, 2, 1 (dependent upon coding, resolution, and stream configuration) Available Resolutions Resolution MJPEG H.264 High Profile Additional Resolutions 640 x 512, 640 x 352, 480 x 368, 480 x 272, 320 x 256, and 320 x 176 Supported Protocols TCP/IP, UDP/IP (Unicast, Multicast IGMP), UPnP, DNS, DHCP, RTP, RTSP, NTP, IPv4, SNMP v2c/v3, QoS, HTTP, HTTPS, LDAP (client), SSH, SSL, SMTP, FTP, and 802.1x (EAP) Users Unicast MPx Width Height Aspect Ratio Maximum IPS Recommended Bit Rate Maximum IPS Recommended Bit Rate 2.1 1920 1080 16:9 15.0 ips 10.0 Mbps 30.0 ips 6.0 Mbps 1.9 1600 1200 4:3 20.0 ips 10.0 Mbps 20.0 ips 4.0 Mbps 1.3 1280 1024 5:4 20.0 ips 10.0 Mbps 20.0 ips 3.3 Mbps 1.2 1280 960 4:3 20.0 ips 10.0 Mbps 20.0 ips 3.0 Mbps 0.9 1280 720 16:9 30.0 ips 10.0 Mbps 30.0 ips 2.9 Mbps 0.5 800 600 4:3 30.0 ips 7.7 Mbps 30.0 ips 2.0 Mbps 0.3 640 480 4:3 30.0 ips 4.9 Mbps 30.0 ips 1.5 Mbps 0.1 320 240 4:3 30.0 ips 1.2 Mbps 30.0 ips 0.5 Mbps Up to 20 simultaneous users depending on resolution settings (2 guaranteed streams) Multicast Unlimited users H.264 Security Access Password protected Software Interface Web browser view and setup Pelco System Integration Endura 2.0 (or later) or Digital Sentry 7.3 (or later) Open API Pelco API or ONVIF v1.02 Minimum System Requirements Processor Intel Core 2 Duo microprocessor, 2.6 GHz Operating System Microsoft Windows XP, Windows Vista, or Mac OS X 10.4 (or later) Memory 2 GB RAM Network Interface Card 100 megabits (or greater) Monitor Minimum of 1024 x 768 resolution, 16- or 32-bit pixel color resolution Web Browser* Internet Explorer 7.0 (or later) or Mozilla Firefox 3.5 (or later); Internet Explorer 8.0 (or later) is recommended for configuring analytics Media Player Pelco Media Player or QuickTime 7.6.5 for Windows XP, Windows Vista, or QuickTime 7.6.4 for Mac OS X 10.4 *Internet Explorer is not supported by Mac OS X 10.4. This product is not compatible with QuickTime version 7.6.4 for Windows XP or Windows Vista. If you have this version installed on your PC, you will need to upgrade to QuickTime version 7.6.5. ANALYTICS Required Systems for Pelco Analytics Pelco Interface Open API Required System for Object Video Suites WS5200 Advanced System Management Software on an Endura 2.0 (or later) system The Pelco API can transmit behavior alarm data to third-party applications, available at pdn.pelco.com. OV ready-compliant system with OV Ready video management system

MODELS MODELS IDE20DN-0 IDE20DN-1 IDE20DN8-1 IDE20DN-OCP0 IDE20DN-OS0 IDE20DN-OSP0 IDE20DN-OCP1 IDE20DN-OS1 IDE20DN-OSP1 Sarix indoor fixed dome network camera, extended platform with built-in Pelco Analytics, 2.1 MPx, day/night, no lens, smoked dome Sarix indoor fixed dome network camera, extended platform with built-in Pelco Analytics, 2.1 MPx, day/night, no lens, clear dome Sarix indoor fixed dome network camera, extended platform with built-in Pelco Analytics, 2.1 MPx, day/night, 2.8 ~ 8 mm varifocal megapixel lens, clear dome Sarix indoor fixed dome network camera, extended platform, 2.1 MPx, day/night, no lens, smoked dome, with built-in OV Event Counting Plus Suite Sarix indoor fixed dome network camera, extended platform, 2.1 MPx, day/night, no lens, smoked dome, with built-in OV Security Suite Sarix indoor fixed dome network camera, extended platform, 2.1 MPx, day/night, no lens, smoked dome, with built-in OV Security Plus Suite Sarix indoor fixed dome network camera, extended platform, 2.1 MPx, day/night, no lens, clear dome, with built-in OV Event Counting Plus Suite Sarix indoor fixed dome network camera, extended platform, 2.1 MPx, day/night, no lens, clear dome, with built-in OV Security Suite Sarix indoor fixed dome network camera, extended platform, 2.1 MPx, day/night, no lens, clear dome, with built-in OV Security Plus Suite CERTIFICATIONS/RATINGS/PATENTS CE, Class B FCC, Class B UL/cUL Listed C-Tick Patents Pending ONVIF v1.02 KCC* *As of the date of this publication, this certification is pending. Consult the factory, our Web site at www.pelco.com, or the most recent B.O.S.S. update for the current status of certifications. OPTIONAL ACCESSORIES IX-SC Service/monitor cable, 1.22 m (4 ft); compatible with standard BNC connectors AUD-1 External audio accessory ALM-1 External alarm accessory POE20U560G Single port PoE injector RECOMMENDED MOUNTS ID-P Pendant mount ID-DF5 DF5 Series adapter kit ID-CB Conduit box for in-ceiling installations ID-PCB 61 x 61 cm (2 x 2 ft) ceiling panel with conduit box SWM-WT Wall mount for pendant SWM-CAWT Corner adapter for wall mount SWM-PAWT Pole adapter for wall mount RECOMMENDED LENSES 13M2.2-6 Megapixel lens, varifocal, 2.2 ~ 6.0 mm, f/1.3 ~ 2.0 13M2.8-8 Megapixel lens, varifocal, 2.8 ~ 8.0 mm, f/1.2 ~ 1.9 13M2.8-12 Megapixel lens, varifocal, 2.8 ~ 12.0 mm, f/1.4 ~ 2.7 13M15-50 Megapixel lens, varifocal, 15.0 ~ 50.0 mm, f/1.5 ~ 2.1 Pelco lenses have been designed and tested to deliver optimal image quality for the IDE20 Series megapixel camera. The use of standard definition lenses on IDE20 Series megapixel cameras will limit the resolution of the camera, creating poor image quality. 2.2 mm 2.8 mm 6.0 mm 8.0 mm 12.0 mm 15.0 mm 50.0 mm Field of View in Degrees Aspect Ratio 16:9 4:3 5:4 Horizontal 109 109 109 Vertical 63 83 89 Horizontal 89 89 89 Vertical 48 66 70 Horizontal 42 42 42 Vertical 24 32 34 Horizontal 32 32 32 Vertical 18 24 25 Horizontal 21 21 21 Vertical 12 16 17 Horizontal 16 16 16 Vertical 9 12 13 Horizontal 5 5 5 Vertical 3 4 4 Note: For 800 x 600 (or lower) resolutions in 4:3 or 5:4 aspect ratios, the field of view is smaller than listed above. Refer to the Installation/Operation manual for details. Pelco by Schneider Electric 3500 Pelco Way, Clovis, California 93612-5699 United States USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. All other product names and services are the property of their respective companies. ONVIF and the ONVIF logo are trademarks of ONVIF Inc. Product specifications and availability are subject to change without notice. Copyright 2012, Pelco, Inc. All rights reserved.

PRODUCT SPECIFICATION camera solutions 13M Series Megapixel Varifocal Lens 1/3-INCH FORMAT, 3 MEGAPIXEL, AUTO IRIS (DIRECT DRIVE) Product Features Up to 3 Megapixels (MPx) CS Mount For use with 1/3-Inch Cameras Auto Iris, Manual Focus, and Zoom High Resolution Power in a Compact Body Aspherical Elements 13M15-50 Pelco s 13M Series megapixel varifocal lenses are a new class of lenses specially designed to provide optimal results when used in cameras with megapixel sensors. These lenses enable megapixel cameras to realize the high resolutions that standard lenses cannot deliver, with a resolving power of up to 100 lines per millimeter. These lenses provide excellent image quality at both the center and at the corner of the image. Ø/W L H The 13M Series offers versatility and flexibility in a compact package. Each auto iris lens covers a specific range of focal lengths, so you can adjust the lens to achieve the exact field of view instead of almost the right view. Appropriate for indoor and outdoor lighting situations, the 13M Series lenses will fit all 1/3-inch CS-mount cameras requiring DC drive auto iris lenses. The lenses also include a spot filter. A factory-installed square 4-pin plug is standard for ease of installation. Lenses in this series are available in 2.7X, 2.8X, 3.3X, and 4.3X zoom with varying focal lengths. H ØW L 13M2.2-6 1.85 (4.71) 1.61 (4.08) 2.13 (5.40) 13M2.8-8 1.85 (4.71) 1.61 (4.08) 2.05 (5.20) 13M2.8-12 2.01 (5.11) 1.92 (4.88) 2.58 (6.55) 13M15-50 1.79 (4.55) 1.48 (3.75) 2.30 (5.85) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. Designed especially for low-light capability, Pelco s 13M Series lenses are extremely fast. These lenses provide excellent performance across a wide range of lighting conditions. The 13M Series also provides excellent day/night performance in Pelco Sarix cameras that are capable of this function, which includes operation with IR lighting and visible lighting. The 13M Series lenses have a slip mechanism that allows it to be easily adjusted and oriented inside enclosures, domes, and so forth. In addition, the metal mount makes for a robust and secure attachment to cameras. International Standards Organization Registered Firm; ISO 9001 Quality System C785 / REVISED 7-2-10

TECHNICAL SPECIFICATIONS MODEL 13M2.2-6 13M2.8-8 13M2.8-12 13M15-50 Type Varifocal Varifocal Varifocal Varifocal Format Size 1/3-inch 1/3-inch 1/3-inch 1/3-inch Mount Type CS CS CS CS Focal Length 2.2 ~ 6.0 mm 2.8 ~ 8.0 mm 2.8 ~ 12.0 mm 15.0 ~ 50.0 mm Zoom Ratio 2.7X 2.8X 4.3X 3.3X F-number (iris fully opened) 1.3 ~ 2.0 1.2 ~ 1.9 1.4 ~ 2.7 1.5 ~ 2.2 Image Size 6 mm diameter 6 mm diameter 6 mm diameter 6 mm diameter Flange Focal Length 12.5 mm 12.5 mm 12.5 mm 12.5 mm Minimum Object Distance 0.3 m 0.3 m 0.3 m 0.8 m Iris Auto Auto Auto Auto Field of View Wide Vertical 91 73 74 14 Horizontal 120 100 100 18 Diagonal 146 128 127 23 Tele Vertical 35 26 17 4.2 Horizontal 46 35 23 5.6 Diagonal 57 43 29 6.9 Focus Manual Manual Manual Manual Zoom Manual Manual Manual Manual Operating Temperature 14 to 122 F ( 10 to 50 C) 14 to 122 F ( 10 to 50 C) 14 to 122 F ( 10 to 50 C) 14 to 122 F ( 10 to 50 C) Storage Temperature 4 to 140 F ( 20 to 60 C) 4 to 140 F ( 20 to 60 C) 4 to 140 F ( 20 to 60 C) 4 to 140 F ( 20 to 60 C) Relative Humidity 35% to 90% 35% to 90% 35% to 90% 35% to 90% Iris Drive Coil Resistance 190 Ω ±10% 190 Ω ±10% 190 Ω ±10% 190 Ω ±10% Iris Damping Coil Resistance 500 Ω ±10% 500 Ω ±10% 500 Ω ±10% 500 Ω ±10% Maximum Iris Operating Current 23 ma at 4 VDC 23 ma at 4 VDC 23 ma at 4 VDC 23 ma at 4 VDC Unit Weight (approximate) 0.13 lb (0.06 kg) 0.13 lb (0.06 kg) 0.20 lb (0.09 kg) 0.13 lb (0.06 kg) Shipping Weight (approximate) 1 lb (0.5 kg) 1 lb (0.5 kg) 1 lb (0.5 kg) 1 lb (0.5 kg) Note: When power is turned off, the iris will close automatically. CERTIFICATIONS CE C-Tick Pelco, Inc. Worldwide Headquarters: 3500 Pelco Way, Clovis, California 93612-5699 USA USA & Canada Tel: (800) 289-9100 FAX: (800) 289-9150 International Tel: +1 (559) 292-1981 FAX: +1 (559) 348-1120 www.pelco.com Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. All other product names and services are the property of their respective companies. Product specifications and availability are subject to change without notice. Copyright 2010, Pelco, Inc. All rights reserved.

BRACKETS - Roof Top Brackets PA2 / SRCW2000 DESCRIPTION The PA2 is designed to allow camera housings to be mounted below the roofl ine. There is a pivot point on the mount, allowing the unit to be fl ipped back over the roof for servicing. The PA2 is compatible with most VIDEOLARM wall mounts which attach directly to the mounting face plate. Can not be used with the WM1200, 9000HW or DECO1. PA2 FEATURES Lowers dome below roof line, fl ips back over roof for servicing Heavy-gauge steel for maximum stability Durable powder coat fi nish 150 lb load rating Face Plate 11" 7/16" 4" 5.5" 8" 8" 12" 1" 2" 3" Mounting Plate SHIPPING SPECIFICATIONS Model Unit Weight Shipping Weight Shipping Box Dim. PA2 16 lbs 16 Grd/16 Air 14 x 14 x 14 * Shipping weights depend on box dimensions. DESCRIPTION The SRCW2000 heavy duty mount is designed for either parapet or fl at roof applications, allowing the camera to be raised above the roofl ine. Service can be accomplished by rotating the unit in over the roof. Most VIDEOLARM wall mounts which attach directly to the mounting face plate are compatible with the SRCW2000. Can not be used with the WM1200, 9000HW or DECO1. SRCW2000 FEATURES Raises camera above roof line, rotates in for servicing camera Heavy-gauge steel for maximum stability Durable powder coat fi nish 150 lb load rating 4.0" 11 22.0" 5.5" 8" Roof Plate 34"3" 2 2 17 4 4 Brackets 12 1 6.5 7 5 7 6.5 2 1.5 17 SHIPPING SPECIFICATIONS Model Unit Weight Shipping Weight Shipping Box Dim. SRCW2000 47 lbs 47 Grd/47 Air 22 x 22 x 16 3.5 * Shipping weights depend on box dimensions. Product specifi cations are subject to change without notice. 90 2525 Park Central Blvd Decatur GA 30035 770-987-7550 www.videolarm.com info@videolarm.com

PRODUCT SPECIFICATION camera solutions IWM Series, IWM24 Series, and IDM4018 Mount WALL MOUNT, SPECTRA, DF5, DF8, AND SARIX IE SERIES DOMES Product Features For Use with Spectra, DF5, DF8, and Sarix IE Series Domes; Can Also Be Used with Other Pendant Domes Using 1.5-inch NPT Threaded Pipe for Mounting Constructed of Aluminum (IDM4018) and Cast Aluminum (IWM Series) Mounts Directly to Vertical Load-Bearing Surface for Wall Mount Applications Supports up to 75 lb (34 kg) Includes Cable Feedthrough Hole IWM24 Series Includes Integral 24 VAC, 100 VA Transformer for Use with Spectra and Sarix IE Series Domes Optional Parapet, Pole, and Corner Adapters are Available IWM24-GY The IWM Series, IWM24 Series, and IDM4018 indoor/outdoor wall mounts are designed primarily for use with Pelco pendant domes including Spectra, DF5, DF8, and Sarix IE Series. They can also be used with other pendant domes that require 1.5-inch NPT pipe thread for installation. For Sarix IE Series domes, the IWM-SR and IWM24-SR wall mounts require the Sarix IE-P pendant mount adapter. 14.629 (37.15) 8.0 7.5 (20.32) (19.05) 6.5 (16.51) All mounts feature a feedthrough opening in the mounting surface for easy routing of video and power cables and are threaded for 1.5-inch NPT pipe, making them ready to accept a variety of Pelco pendant back box models. 13.50 (34.30) 4.5 (11.43) 5.50 (13.97) The IWM24 Series includes an integral 24 VAC, 100 VA transformer. Input power (120 or 240 VAC, 50/60 Hz) is selectable using an internal slide switch that is easily accessible through a front access cover plate. Input wiring can enter the arm from openings in the mounting plate or a flexible metal conduit fitting may be installed on the bottom of the mount. When installed with Sarix IE Series domes, the power from the IWM24-SR mount is used for the dome heater. NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. The IWM Series, IWM24 Series, and IDM4018 mounts can be attached directly to any vertical load-bearing surface. All mounts are designed to support up to 75 pounds (34 kg). The IWM Series and IWM24 Series are constructed of cast aluminum and are available in black, gray, or light gray finish. The IDM4018 is constructed of aluminum and has a gray polyester powder coat finish. Optional parapet, pole, and corner adapters are available. International Standards Organization Registered Firm; ISO 9001 Quality System C203 / REVISED 10-6-10

TECHNICAL SPECIFICATIONS MODELS IWM-BK IWM-GY IWM-SR IWM24-BK IWM24-GY IWM24-SR IDM4018 ELECTRICAL (IWM24 Series Only) Input Power Output Power Fuse Wall mount with cable feedthrough for use with Spectra, DF5, and DF8 Series pendant domes; black finish. Same as IWM-BK except gray finish. Same as IWM-BK except light gray finish.* Wall mount with cable feedthrough for use with Spectra, DF5, and DF8 Series pendant domes; includes integral 24 VAC, 100 VA transformer; black finish. Same as IWM24-BK except gray finish. Same as IWM24-BK except light gray finish.* Wall mount with removable front end cap and feedthrough capabilities for use with Spectra, DF5, and DF8 Series pendant domes. 120/240 VAC, 50/60 Hz, switchable through an internal slide switch 24 VAC, 100 VA transformer One 1.6 A, 120 VAC, fast acting One 500 ma, 240 VAC, fast acting CERTIFICATIONS/RATINGS CE compliant (IWM24-BK, IWM24-GY, and IWM24-SR only) UL/cUL Listed (IWM/IWM24 Series only) Meets NEMA Type 4 Standards (IWM/IWM24 Series only) OPTIONAL MOUNT ADAPTERS Corner CM400 Pole PA402 Parapet PP400 PP4348 Corner mount adapter; use with IDM4018 and IWM/IWM24 Series Pole mount adapter; use with IDM4018 and IWM/IWM24 Series Parapet wall adapter; use with IDM4018 and IWM/IWM24 Series Rooftop parapet adapter; use with IDM4018 and IWM/IWM24 Series GENERAL Suggested Mounting Method IWM/IWM24 Series Secure with four 3/8-inch fasteners (not supplied) suitable for the mounting surface IDM4018 Secure with four 5/16-inch fasteners (not supplied) suitable for the mounting surface Dome Mounting Dome screws directly into mount Cable Entry IWM Series and IDM4018 One cable feedthrough hole in mounting plate IWM24 Series Two cable feedthrough holes in mounting plate; can accommodate 1/2-inch (1.27 cm) conduit fittings or PG13.5 liquid-tight gland fittings; one 3/4-inch (1.91 cm) conduit opening on the bottom of mount arm for flexible metal conduit connectors Maximum Load 75 lb (34 kg) Effective Projected Area (EPA) IWM/IWM24 Series ~48 square inches IDM4018 ~54 square inches Construction IWM/IWM24 Series Cast aluminum IDM4018 5052H32 Aluminum Finish IWM-BK Black polyester powder coat IWM-GY Gray polyester powder coat IWM-SR Light gray polyester powder coat IWM24-BK Black polyester powder coat IWM24-GY Gray polyester powder coat IWM24-SR Light gray polyester powder coat IDM4018 Gray polyester powder coat Environment Indoor/outdoor Weight Unit Shipping IWM Series 2.46 lb (1.12 kg) 7 lb (3.17 kg) IWM24 Series 6.58 lb (2.98 kg) 11 lb (4.98 kg) IDM4018 4.00 lb (1.81 kg) 6 lb (2.71 kg) 0.75 (1.90) 6.50 (16.51) 0.75 (1.90) 4.50 (11.43) 6.00 (15.24) 8.00 (20.32) IDM4018 2.50 (6.35) 0.31 (0.95) THRU (4X) 18.00 (45.72) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. *The IWM-SR and IWM24-SR require the IE-P adapter for use with Sarix IE Series domes. 1.75 (4.45) Pelco, Inc. Worldwide Headquarters: 3500 Pelco Way, Clovis, California 93612-5699 USA USA & Canada Tel: (800) 289-9100 FAX: (800) 289-9150 International Tel: +1 (559) 292-1981 FAX: +1 (559) 348-1120 www.pelco.com Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. All other product names and services are the property of their respective companies. Product specifications and availability are subject to change without notice. Copyright 2010, Pelco, Inc. All rights reserved.

PRODUCT SPECIFICATION camera solutions CM400 Mount CORNER MOUNT, SPECTRA AND LEGACY ADAPTER Product Features Low Cost Rugged Construction Supports up to 75 Pounds (34 kg) Corner Mount Adapter for Spectra and Legacy Wall Mounts (IWM Series, IDM4018, and LWM41) Design Includes Mounting Studs for Quick, Simple, Installation of Wall Mount The CM400 is a corner mount adapter designed for use with Spectra and Legacy wall mounts. For Spectra, DF5, or DF8 Series pendant domes, use the IWM Series or IDM4018 wall mount. For Legacy positioning systems, use the LWM41 wall mount. 12.00 (30.84) The LWM41, IWM Series, or IDM4018 wall mount is secured to the CM400 by four 5/16-inch mounting studs; nuts and split lock washers are supplied. 4.50 (11.43) Constructed from aluminum, the CM400 is capable of supporting up to 75 pounds (34 kg) and features a cable feedthrough hole for easy routing of video and power cables. A block-off plate is included for non-feedthrough outdoor applications. 7.00 (17.78) 4.50 (11.43) 8.00 (20.32) 2.00 (5.08) 6.50 (16.5) 6.75 (17.15) 8.00 (20.32).37 (.94) THRU 8X.625 (1.59) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. C281 / REVISED 10-03 International Standards Organization Registered Firm; ISO 9001 Quality System

TECHNICAL SPECIFICATIONS MODEL CM400 Corner mount adapter for IWM Series, IDM4018, and LWM41 wall mounts RELATED PRODUCTS IWM Series IDM4018 LWM41 EA4348 Wall mount with cable feedthrough for use with Spectra, DF5, and DF8 Series pendant style domes. Wall mount with removable front end cap and cable feedthrough for use with Spectra, DF5, and DF8 Series pendant style domes. Legacy wall mount. For use with Legacy integrated positioning systems. EWM adapter plate. Allows an EWM wall mount to be installed on a CM400 for use with an Esprit Series integrated positioning system. MECHANICAL Adapter Mounting Mounting Method GENERAL Construction Finish Maximum Load Unit Weight Shipping Weight Four 5/16-inch mounting studs (nuts and split lock washers supplied) for attaching LWM41, IDM4018, EA4348, or IWM Series mount Secure with eight fasteners suitable for mounting surface (minimum 1/4-inch recommended, not supplied) 6061 T6 aluminum, 0.125-inch (3.18mm) thick Gray polyester powder coat 75 lb (34 kg) 3 lb (1.36 kg) 8 lb (3.62 kg) Pelco, Inc. Worldwide Headquarters: 3500 Pelco Way, Clovis, California 93612-5699 USA USA & Canada Tel: (800) 289-9100 FAX: (800) 289-9150 International Tel: +1 (559) 292-1981 FAX: +1 (559) 348-1120 www.pelco.com Pelco, the Pelco logo, Esprit, Legacy, and Spectra are registered trademarks of Pelco, Inc. Product specifications and availability subject to change without notice. Copyright 2003. Pelco, Inc. All rights reserved.

PRODUCT SPECIFICATION camera solutions PA402 Mount POLE MOUNT, SPECTRA AND LEGACY ADAPTER Product Features Low Cost Rugged Construction Supports up to 75 Pounds (34 kg) Pole Mount Adapter for Spectra and Legacy Wall Mounts (IWM Series, IDM4018, and LWM41) Design Includes Mounting Studs for Quick, Simple Installation of Wall Mount PA402 SHOWN WITH REMOVABLE BLOCK-OFF PLATE The PA402 is a pole mount adapter designed for use with Spectra and Legacy wall mounts. For Spectra, DF5, or DF8 Series pendant domes, use the IWM Series and IDM4018 wall mount. For Legacy positioning systems, use the LWM41 wall mount. Ø3.00 (7.62) THRU, 2X 4.50 (11.43) The LWM41, IWM Series, or IDM4018 wall mount is secured to the PA402 by four 5/16-inch mounting studs; nuts and split lock washers are supplied. Constructed from aluminum, the PA402 is capable of supporting up to 75 pounds (34 kg) and features a cable feedthrough hole for easy routing of video and power cables. A block-off plate is included for non-feedthrough outdoor applications. 12.77 (32.44) 6.50 (16.5) The PA402 is for use on poles having a 3-inch (7.62 cm) to 8-inch (20.32 cm) diameter. 2.46 (6.24) 2.75 (6.98) 7.00 (17.78) NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES. C274 / REVISED 1-06 International Standards Organization Registered Firm; ISO 9001 Quality System

TECHNICAL SPECIFICATIONS MODEL PA402 Pole mount adapter for IWM Series, IDM4018 and LWM41 wall mounts RELATED PRODUCTS IWM Series IDM4018 LWM41 EA4348 Wall mount with cable feedthrough for use with Spectra, DF5, or DF8 Series pendant style domes. Wall mount with removable front end cap and cable feedthrough for use with Spectra, DF5, or DF8 Series pendant style domes. Legacy wall mount. For use with Legacy integrated positioning systems. EWM adapter plate. Allows an EWM wall mount to be installed on a PA402 for use with an Esprit Series integrated positioning system. MECHANICAL Adapter Mounting Mounting Method GENERAL Construction Finish Maximum Load Unit Weight Shipping Weight Four 5/16-inch mounting studs (nuts and split lock washers supplied) for attaching LWM41, IDM4018, EA4348, or IWM Series mount Slots for mounting straps; three stainless steel straps supplied. Straps fit 3-inch (7.62 cm) to 8-inch (20.32 cm) diameter pole. 5052H32 aluminum, 0.190-inch (4.8 mm) thick Gray polyester powder coat 75 lb (34 kg) 3.48 lb (1.58 kg) 5 lb (2.27 kg) Pelco, Inc. Worldwide Headquarters: 3500 Pelco Way, Clovis, California 93612-5699 USA USA & Canada Tel: (800) 289-9100 FAX: (800) 289-9150 International Tel: +1 (559) 292-1981 FAX: +1 (559) 348-1120 www.pelco.com Pelco, the Pelco logo, Esprit, Legacy, and Spectra are registered trademarks of Pelco, Inc. Product specifications and availability subject to change without notice. Copyright 2006, Pelco, Inc. All rights reserved.

Altronix Vertiline CCTV Rack Mount Power Supplies provide 16 power outputs in a space saving 1U EIA 19 rack mount chassis which may be rack, wall or shelf mounted. The units feature individually selectable 24VAC and/or 28VAC power outputs with surge suppression. Vertiline CCTV Rack Mount Power Supplies are also available in eight (8) and twenty-four (24) output models with various power ratings. Input: Selectable 115VAC 60 Hz/230VAC 50/60 Hz input. - 115VAC 60 Hz., 4 amp - 230VAC 50/60 Hz., 2.5 amp Output: Sixteen (16) individually selectable 24VAC or 28VAC power outputs with OFF position. 24VAC or 28VAC @ 14 amp total output current. Sixteen (16) external blade fuse protected outputs rated @ 3 amp (VertiLine166). Sixteen (16) PTC protected outputs rated @ 2.5 amp (VertiLine166D). Main fuse rated @ 15 amp. Surge suppression. Visual Indicators: Sixteen (16) individual power LEDs. VertiLine 166 & VertiLine 166D UL Listed CCTV Rack Mount Power Supplies Rev. DSVertiLine166 - K06H Overview Specifications Features: Illuminated master power disconnect circuit breaker with manual reset. IEC 320-3-wire grounded line cord (detachable). Removable terminal blocks with locking screw flange. Spare fuses provided. Ease of installation saves time and eliminates costly labor. Compact 1U rack mount chassis. Fits standard EIA 19 rack. Units can be rack, wall or shelf mounted. Shipping Weight (approximate): - VertiLine166: 15.4 lbs. - VertiLine166D: 15.4 lbs. VertiLine166 CCTV Rack Mount Power Supply w/sixteen (16) fuse protected outputs. Models VertiLine166D CCTV Rack Mount Power Supply w/sixteen (16) PTC protected outputs. UL Listed for Commercial CCTV Equipment (UL 2044). Agency Approvals

1U EIA 19 Rack Mount Chassis Mechanical Drawing & Dimensions: 1.625 H x 19.125 W x 8.5 D REAR 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 1.625" Main Fuse 9-16 N P N P N P N P N P N P N P N P Main Fuse 1-8 N P N P N P N P N P N P N P N P AC POWER TOP & BOTTOM 17.625" 8.5" FRONT RESET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 28VAC 28VAC OFF OFF 24VAC 24VAC OFF 19.125".75" (ON) Altronix Corp. - 140 58th Street, Brooklyn, NY 11220 718-567-8181 888-258-7669 altronix.com

DTK-PVPIP IP Video Power and Data Surge Protection General Product Specifications IP Video is becoming the favored method for transmitting surveillance camera video to NVRs and monitoring stations, and more installers are taking advantage of its lower cabling and installation costs. The benefit of less expensive cabling comes with a price, however: unshielded wiring. IP Video applications demand surge protection! DITEK s PVP line of camera surge protectors provide optimum protection of power, data and video connections in a single product. The DTK-PVPIP protects IP Video cameras and systems from surges on the network cabling and power supply lines. Lowimpedance video/data protection allows full Gigabit Ethernet transmission speed; the 12V or 24V power protection is rated for 5 Amps per pair to power camera plus heaters, blowers, defrosters, or PTZ motors. DTK-PVPIP Product Features Can be used at Camera or individual NVR/Power supply feed RJ45 connection protects all four video/data pairs Two pairs of power protection External grounding screw Conforms to EIA/TIA standards for data transmission Automatically resets to protect against multiple surges Performance Data DTK-PVPIP Data Power Service Voltage 5V 12V / 24V MCOV 6.8V 38V Clamp Voltage 7.9V 47V Peak Surge Current 268A/pair (10/1000µs) 2,000A/pair (8/20µs) Specifications Application Point: Camera Standards Compliance: EIA/TIA568A, EIA/TIA568B Data Rate: Gigabit Ethernet using all four pairs Connection Video/Data: RJ45 In/Out, 8 pins Connection Power: #22-#14AWG screw terminals Max Continuous Current: 0.3A Video/Data, 5A Power Protection Modes: Line-Ground (All) Operating Temperature: -40 F - 158 F (-40 C - 70 C) Maximum Humidity: 95% non-condensing Dimensions: 4.2 x 3.25 x 1.75 (107 x 83 x 44mm) Weight: 5oz (141g) Housing: ABS Warranty: Ten Year Limited Warranty Complementary Products DTK-MRJ45C5E NVR or computer data line protection DTK-MRJPOE Power over Ethernet surge protection DTK-RM16C5 16-Port, Rack Mount Ethernet surge DTK-RM12POE 12-Port, Rack Mount PoE Surge One DITEK Center 1720 Starkey Road Largo, FL 33771 1-800-753-2345 Direct: 727-812-5000 Technical Support: 1-888-472-6100 www.ditekcorp.com Doc. Number: SPS-100062-002 Rev 1 11-09 2009 DITEK Corp. Specification Subject to Change

PRODUCT SPECIFICATION video management solutions NSM5200 Series Network Storage Manager 250 MBPS RECORDING THROUGHPUT, UP TO 36 TB OF RAW CAPACITY, RAID 6 Product Features Recording Throughput up to 250 Mbps Meets Demanding Performance Requirements for Write-Intensive Applications Hardware Designed to Eliminate Single Points of Failure, Including Redundant Fans, Power Supplies, and RAID 6 Storage for Optimum Reliability Pooled Storage Management Provides Automatic Distributed Load Balancing and Active-Active Failover Within a Storage Pool to Ensure Continued Recording if Catastrophic Failure Occurs Hot Standby Failover Provides Redundancy in Installations Where Storage Pooling Cannot Be Utilized. Multicast Recording Support Allows for Recording of Multicast Data Streams for Restricted Bandwidth Scenarios Redundant Recording Ensures Duplication of Vital Data for Mission-Critical Applications Built-in EnduraStor Storage Management Increases Storage Efficiency by Grooming Recorded Streams Based on Age and Priority Ability to Serve 32 Simultaneous Playback Streams Per Storage Pool Performance Levels Maintained in Normal and RAID Error Conditions Built-in Diagnostic Monitoring Provides Preventative Maintenance and SNMP Monitoring Reduced Cost of Ownership and Increased Energy Efficiency Through Consolidation of Multiple Hardware Components into a Fully Integrated Chassis The NSM5200 Series delivers industry leading performance and innovation for mission-critical storage needs. The combination of high performance, scalable hardware design and advanced software capabilities enables the NSM5200 to meet the unique storage needs of physical security and surveillance applications. Hardware Built for Performance, Reliability, and Scalability The demands of surveillance applications place unique strains on storage subsystems. Storage systems require the bandwidth and capacity to keep up with incoming streams. They must also simultaneously manage all other common disk and RAID functions. In addition, physical security applications are almost always mission critical. Any downtime, degraded performance for routine maintenance, or loss of recorded footage is extremely disruptive to the organization s physical security mission. The NSM5200 has been engineered to meet these unique performance and reliability demands. Custom hardware components, to eliminate common performance choke points to a patented scheme for writing content to a disk drive, have been specifically designed to deliver sustained high throughput for recording and playback. The NSM5200 is capable of a maximum of 250 Mbps of throughput for incoming streams while delivering 32 simultaneous playback streams per storage pool. This performance is maintained whether the system is operating under normal conditions, dealing with disk drive errors, or rebuilding the RAID array. The NSM5200 improves the total cost of ownership and energy efficiency by consolidating disparate components into a single chassis. The 250 Mbps throughput provides double the improvement over Pelco s first generation integrated recorder, allowing users to service far more data streams in one storage unit than previously possible. In addition, with the integration of the management server functionality into the storage chassis, cost and energy efficiency is optimized by eliminating the cost of additional servers and the associated heating, ventilation, and cooling costs. Finally, the use of lower power components and adaptive cooling inside the chassis manage power dissipation based on load requirements. Reliability is enhanced through the use of redundancy at all common failure points. A CompactFlash card is used to host the operating system for higher reliability than traditional hard disk drives. To mitigate any downtime resulting from CompactFlash errors, the database is striped across the storage array. The RAID 6 storage configuration provides double parity protection of recorded data. The hard drive bay is cooled through the use of high capacity, redundant fans to ensure that the drives are kept at an optimum operating temperature. Finally, fully redundant power supplies guard against any power supply failure. This Endura distributed, network-based product is available only to certified dealers/integrators. Please contact your local sales representative for details on certification applications and requirements. Additional information on Endura products and certifications may be found at http://www.pelco.com/endura. International Standards Organization Registered Firm; ISO 9001 Quality System C4626 / REVISED 7-27-11

TECHNICAL SPECIFICATIONS As with any other system, maintenance is an important and vital part of sustained operation. The NSM5200 incorporates various innovations to make maintenance more efficient and to allow the system to continue operating at peak performance levels. Easy access to hard disk drives and the CompactFlash card is available from the front panel. A unique rail system allows access to a failed fan should it need to be replaced. Temperature sensors throughout the chassis detect possible air-flow obstruction or clogged intake filters. The use of enterprise-class SAS technology provides advanced enclosure management and monitoring. Notifications of potential or actual issues are transmitted to the specified user interfaces for action. Storage capacity is scaled using third-party storage arrays with an optional fibre channel interface. Software Built for Flexibility, Reliability, Cost Optimization In addition to unique strains placed on hardware components, surveillance applications also demand innovations in software. Recording software must accommodate automatic failover should a catastrophic failure occur. Recording software must deal with file fragmentation caused by overwrite, locking of video clips, and managing metadata associated with alarms and events. Finally, recording software must deal with the escalating cost of storage by finding innovative ways to manage recorded content. This ensures that the user extracts the most value from the cost of the storage subsystem. The NSM5200 supports the pooling of multiple recorders to provide for automatic load balancing and failover. Up to twenty NSM5200 nodes can be placed into the same storage pool. One of the NSM5200s in the pool acts as the master and manages the assignment of incoming streams, health monitoring, and redistribution of the recording load. Should a unit fail, the given streams are automatically redistributed to the remaining units in the storage pool. When the failed unit is brought back on line, the recording load is distributed again such that the load on any given recorder is balanced. This capability also allows users to dynamically add additional storage to a pool as their retention needs change. Single NSM5200s can be monitored by another NSM5200 or an entire storage pool when the single NSM5200 cannot be incorporated into a standard storage pool. For mission-critical applications where business continuity is essential, the NSM5200 supports redundant recording. Independent schedules can be created on both the primary and redundant storage pools to ensure that the most vital data is duplicated across physical boundaries. The NSM5200 incorporates an improved version of Pelco s patented EnduraStor storage optimization technology. EnduraStor was developed to manage the cost of storing high resolution, high-frame rate video by leveraging the fact that the value of recorded video is typically higher immediately following an incident. Organizations are capable of specifying a desired delay period during which all recorded video will be kept at 30 images per second (25 for PAL). As the age of video available on hard disk drives exceeds the delay period, it is automatically groomed to a lower frame rate, thus freeing up storage capacity for new data. The NSM5200 incorporates advancements in the EnduraStor algorithm, which gives administrators the option of classifying the priority level of alarm or event video to retain the full frame rate. The NSM5200 is built upon the proven stability and robustness of its Linux -based operating system. It utilizes an XFS file system and automated defragmentation routines to keep the database from becoming fragmented. XFS has been proven to be a more superior file format for the rigors of surveillance recording applications than an NTFS file system, which is standard with Windows -based recorders. The NSM5200 incorporates a number of diagnostic monitoring functions that serve vital roles in notifying operators of potential problems and failures. Integrated diagnostics utilize on-board LED indicators to display warnings and failures on the NSM5200 and then it reports these failures to operators. The NSM5200 monitors and provides warning messages for items such as retention time issues, accumulation of software errors, network errors that result in packet loss, and changes to network link speeds. It also monitors and reports hardware diagnostics such as temperatures approaching established thresholds, hard disk drive failures, fan failures, power supply failures, or when a stream or a NSM5200 is off line. Finally, the NSM5200 can communicate to an APC Smart-UPS series uninterruptible power supply to provide battery status information and initiate a graceful shutdown if the available charge falls below its designated threshold.

TECHNICAL SPECIFICATIONS MODELS The following table describes the NSM5200 model numbers. For example, the model number for a 6 TB, no expansion unit with a United Kingdom power cord is NSM5200-06-UK. Note: Units shipped to China do not include power cords. Model Storage Country Code NSM5200 (no expansion) NSM5200F (fibre channel expansion) 3 TB 6 TB 12 TB 24 TB 36 TB US = North America EU = Europe UK = United Kingdom CN = China AU = Australia AR = Argentina SYSTEM Operating System Linux RAID Level RAID 6 Effective Capacity Up to 27.2 TB Drive Interface SAS/SATA II Recommended PC Requirements Web Browser Microsoft Internet Explorer 6.x (or later) with Adobe Flash Player 10 (or later) NETWORK Interface Auxiliary Interfaces USB 2.0 2, 1 Gbps Ethernet RJ-45 ports (1000Base-T) 3 ports (2 rear, 1 front) SUPPLIED ACCESSORIES Power Cord 2 power cords (based on country designation) Note: Units shipped to China do not include power cords Rack Mount Kit Brackets, rails, and hardware OPTIONAL ACCESSORIES NSM5200-PS Replacement power supply module NSM5200-FAN Replacement system fan (upper-middle) NSM5200-FANB Replacement rear-chassis (rear panel) fan NSM5200-FC Fibre channel expansion card HD5200-250 Replacement 250 GB drive and carrier HD5200-500 Replacement 500 GB drive and carrier HD5200-1000 Replacement 1 TB drive and carrier HD5200-2000 Replacement 2 TB hard drive and carrier HD5200-3000 Replacement 3 TB hard drive and carrier

TECHNICAL SPECIFICATIONS FRONT PANEL INDICATORS Power Blue Pelco badge Software Status Green, amber, red (based on diagnostics) Ethernet Port 1 Green, red, off Ethernet Port 2 Green, red, off Unit Status Green, amber, red Hard Drive Status Green, red POWER Power Input 100 to 240 VAC, 50/60 Hz, autoranging Power Supply Internal, dual-redundant, hot swappable Power Consumption Operating Average 100 VAC 262 W, 2.65 A, 895 BTU/H 115 VAC 263 W, 2.31 A, 895 BTU/H 220 VAC 254 W, 1.25 A, 868 BTU/H ENVIRONMENTAL Operating Temperature 10 to 35 C (50 to 95 F) at unit air intake Storage Temperature 40 to 65 C ( 40 to 149 F) Operating Humidity 20% to 80%, noncondensing Max Humidity Gradient 10% per hour Operating Altitude 16 to 3,048 m ( 50 to 10,000 ft) Operating Vibration 0.25 G at 3 Hz to 200 Hz at a sweep rate of 0.5 octave/minute Note: The temperature at the unit air intake can be significantly higher than room temperature. Temperature is affected by rack configuration, floor layout, air conditioning strategy, and other issues. To prevent hard disk drive failure and unit damage, make sure the temperature at the air intake of the unit is continuously within the operating temperature range. PHYSICAL Construction Finish Front Panel Chassis Dimensions (without rails) Unit Weight Empty (without drives) Loaded (with drives) Shipping Weight Mounting Options Steel cabinet Gray metallic with black end caps Black matte finish 61.8 x 43.2 x 13.2 cm (24.3" D x 17.0" W x 5.2" H) 21 kg (46.4 lb) 30 kg (66.8 lb) 35 kg (77.0 lb) Rack, 3 RU per unit (rack rails and hardware are supplied) CERTIFICATIONS/RATINGS CE, Class A; meets EN50130-4 standard requirements FCC, Class A UL/cUL Listed C-Tick S-Mark for Argentina CCC Pelco by Schneider Electric 3500 Pelco Way, Clovis, California 93612-5699 United States USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. All other product names and services are the property of their respective companies. Product specifications and availability are subject to change without notice. Copyright 2011, Pelco, Inc. All rights reserved.

Code Blue PAS 1-d Product Sheet PEDESTAL INTERACTIVE PUBLIC ADDRESS COMMUNICATION SYSTEM The PAS (Public Address System) 1-d, based on Code Blue s popular CB 1-d model, was exclusively designed as an emergency communication system to deliver maximum audio clarity and range to ensure notifications are accurately broadcast to your intended audience. The unique multi-speaker design delivers optimal audio source dispersion utilizing stateof-the-art amplifiers and horn array. PAS is supported by the ToolVox Communication Manager with EMS, UPD and Blue Alert, Code Blue s NFPA 72, 2010 ECS (Chapter 24)-compliant solution, for managing text-tospeech, live broadcast, pre-recorded messages and warning tones options, as well as announcement repeat and scheduling features. Blue Alert s sophisticated software control allow users to quickly inform and direct people in emergency situations. For sites with existing CB 1-d models (made after 1999), the PAS speaker array may be added to extend the emergency units functionality. This modular design allows for flexibility in placement and a lower cost of replacing the entire unit. PAS 1-d is an excellent choice when instant mass notification of a geographic area is essential. Standard Features Analog and VoIP speakerphone options ToolVox Communication Manager compatible with Blue Alert, EMS and UPD software integration 2 Auxiliary inputs/3 Auxiliary outputs (3 NO or 3 NC) 24v LED high intensity, low consumption area light Second opening with blank stainless steel plate 24v LED combo beacon/strobe LED lit stainless steel faceplate Ultra-weather resistant finish Vandal resistant hardware ADA compliant Silent turn-on 360 degree audio dispersion Temperature, output and clipping signal self-monitoring Optional Features Two-button speakerphone/ two-button w/keypad Custom colors & graphics NightCharge Second opening options Overhead camera mount GSM & IP wireless communication options Code Blue 92 East 64 th ST. Holland, MI 49423 800.205.7186 www.codeblue.com CS-120-F

Code Blue PAS 1-d Product Sheet Unit Specifications FACEPLATE OPTIONS Overall Height 121 (307.34 cm) FP1 FP2 FP2-K Outside Diameter 12.75 (32.38 cm) Housing Material, steel.25 (.635 cm) Access Opening (w x h) 8.5 x 12 (21.59 x 30.48 cm) Overall Weight 470 lbs. (213.2 kg) INFO 1 2 3 4 5 6 7 8 9 CALL Standard Power Requirements 120v AC * 0 # PUSH FOR HELP PUSH FOR HELP PUSH FOR HELP PAS Speaker Specifications Frequency Response 450Hz-7kHz Power Capacity 420w continuous program Impedance 5.3 Ohms Code Blue Standard faceplate assembly with single red PUSH FOR HELP button Code Blue Optional faceplate assembly with additional black INFO button Code Blue Optional faceplate assembly with additional CALL button and keypad PAS Amplifier Specifications Output Power Maximum Output Power Max Bridged Output Power Sensitivity Distortion Frequency Response Signal to Noise 150w (20Hz-20kHz, 0.1% THD) 160w (20Hz-20kHz, 1% THD) 500w (1% THD) 3.5 Vrms 0.05% (0.03% average) 20Hz-20kHz, +0.5dB 117dB Unit Finish Colors Standard Painted Finish British Racing Green, Cardinal Red, Dark Bronze, Gloss White, Gloss Black, Medium Bronze, Midnight Blue, Safety Blue, Safety Red, Safety Yellow Custom Painted Finish Custom colors from Pantone color chart or sample are available as a special order Graphics Text (wording) Standard Custom Assistance, Courtesy, Emergency, Police, Security Custom text graphics are available as a special order Graphics Text Colors Standard (reflective decal) Custom Black, Blue, Green, Red, White, Yellow Custom colors from Pantone color chart or sample are available as a special order Mounting hardware and template for unit is shipped in advanced for foundation work. Specifications subject to change without notice or obligation on the part of the manufacturer. Code Blue 92 East 64 th ST. Holland, MI 49423 800.205.7186 www.codeblue.com pg 2 of 2

Code Blue PAS 2-e Product Sheet WALL MOUNTED INTERACTIVE VOICE COMMUNICATION UNIT WITH PUBLIC ADDRESS SYSTEM Based on the CB 2-e our most popular and cost effective wall mounted unit the PAS (Public Address System) 2-e is exclusively designed for maximum audio clarity and range to ensure your notifications are accurately received by the intended audience. Available in brushed stainless steel or optional painted steel, it is designed for both interior and exterior applications. The exclusive analog InterAct and VoIP speakerphones are designed for maximum reliability, vandal resistance, auxiliary functions, mass notification control, and fault monitoring and reporting capability; leading the market in system programming flexibility. The combination LED beacon/strobe provides a rugged, quality solution for the security conscious customer. The PAS 2 e is an excellent choice for parking decks, dorm entrances, hallways and public transit centers when instant mass notification of a geographic area is essential. Standard Features Analog and VoIP speakerphone options ToolVox Communication Manager compatible with Blue Alert, EMS and UPD software integration 2 Auxiliary inputs/6 Auxiliary outputs (3 NO/3 NC) 12 gauge, 4B brushed stainless steel housing High output combo LED beacon/strobe 24v LED low consumption area light 12-24v AC or DC power Phone line surge suppressor Stainless steel faceplate Ultra-weather resistant finish Vandal resistant hardware UV resistant lenses Waterproof design Wall mounting kit ADA compliant Power Capacity (speaker): 70w continuous program Frequency Response (speaker): 450Hz - 7KHz Impedance (speaker): 8 Ohms Optional Features Two-button speakerphone w/keypad Two-button speakerphone Step-down power transformer Painted finish Custom graphics Code Blue 92 East 64 th ST. Holland, MI 49423 800.205.7186 www.codeblue.com CS-121-F

Call being placed Call received Call being placed Call received Call being placed Call received Code Blue PAS 2-e Product Sheet Unit Specifications FACEPLATE OPTIONS Overall Height 32.25 (81.92 cm) FP1 FP2 FP2-K Width 12.125 (30.79 cm) Depth 7.625 (19.37 cm) Housing Material, stainless steel.105 stainless steel (2.68 mm) Overall Weight 75 lbs. (34 kg) INFO 1 2 3 4 5 6 7 8 9 CALL Standard Power Requirements 12-24v AC or DC * 0 # PUSH FOR HELP PUSH FOR HELP PUSH FOR HELP PAS Speaker Specifications Frequency Response 450Hz - 7kHz Power Capacity 70w continuous power Impedance 8 Ohms Code Blue Standard faceplate assembly with single red PUSH FOR HELP button Code Blue Optional faceplate assembly with additional black INFO button Code Blue Optional faceplate assembly with additional CALL button and keypad Unit Finish Colors Standard Optional Painted Finish 4B brushed stainless steel British Racing Green, Cardinal Red, Dark Bronze, Gloss White, Gloss Black, Medium Bronze, Midnight Blue, Safety Blue, Safety Red, Safety Yellow Custom Painted Finish Custom colors from Pantone color chart or sample are available as a special order Graphics Text (wording) Standard Custom Assistance, Courtesy, Emergency, Police, Security Custom text graphics are available as a special order Graphics Text Colors Standard (reflective decal) Custom Black, Blue, Green, Red, White, Yellow Custom colors from Pantone color chart or sample are available as a special order Each unit is shipped with mounting hardware. Specifications subject to change without notice or obligation on the part of the manufacturer. Code Blue 92 East 64 th ST. Holland, MI 49423 800.205.7186 www.codeblue.com pg 2 of 2

Code Blue CB 4-s Product Sheet WALL/POLE MOUNT INTERACTIVE VOICE COMMUNICATION UNIT The CB 4 s is our basic communication unit designed for wall or pole installations in interior and exterior applications. The all-steel housing and Code Blue s speakerphone system meets the need for a highly vandal resistant unit while providing a cost effective and reliable solution. The exclusive analog InterAct and VoIP speakerphones are designed for maximum reliability, auxiliary functions, mass notification control, and fault monitoring and reporting capability; leading the market in system programming flexibility. The optional remote mount combination LED beacon/strobe kit allows the user flexibility throughout the job. The CB 4 s is a good choice for dorm and building entrances, hallways and transit centers. Standard Features Analog and VoIP speakerphone options ToolVox Communication Manager compatible with Blue Alert, EMS and UPD software integration 2 Auxiliary inputs/3 Auxiliary outputs (3 NO or 3 NC) Stainless steel faceplate Wall mounting kit 24v AC power Voice Identifier ADA compliant Vandal resistant hardware Phone line surge supressor Ultra-weather resistant finish Optional Features Two-button speakerphone w/keypad Two-button speakerphone Custom colors & graphics Pole mounting hardware kit Remote mounted combination LED beacon/strobe kit Code Blue 92 East 64 th ST. Holland, MI 49423 800.205.7186 www.codeblue.com CS-110-E

Code Blue CB 4-s Product Sheet Unit Specifications FACEPLATE OPTIONS Overall Height 13.375 (34.0 cm) FP1 FP2 FP2-K Width 10.25 (26.0 cm) Depth 6 (15.2 cm) Housing Material, steel.125 (0.3 cm) Overall Weight 30 lbs. (13.6 kg) INFO 1 2 3 4 5 6 7 8 9 CALL Standard Power Requirements 24v AC @ 5.5w max * 0 # PUSH FOR HELP PUSH FOR HELP PUSH FOR HELP Unit Finish Colors Standard Painted Finish British Racing Green, Cardinal Red, Dark Bronze, Gloss White, Gloss Black, Medium Bronze, Midnight Blue, Safety Blue, Safety Red, Safety Yellow Code Blue Standard faceplate assembly with single red PUSH FOR HELP button Code Blue Optional faceplate assembly with additional black INFO button Code Blue Optional faceplate assembly with additional CALL button and keypad Custom Painted Finish Custom colors from Pantone color chart or sample are available as a special order Graphics Text (wording) Standard Custom Assistance, Courtesy, Emergency, Police, Security Custom text graphics are available as a special order Graphics Text Colors Standard (reflective decal) Custom Black, Blue, Green, Red, White, Yellow Custom colors from Pantone color chart or sample are available as a special order Remote Mount Combination Beacon/Strobe Provides a highly visual constant blue beacon and a powerful activated strobe for rapid recognition in the unit location. The remote mount feature allows placement for maximum effectiveness. Mounting hardware and template for unit is shipped in advanced for foundation work. Specifications subject to change without notice or obligation on the part of the manufacturer. Code Blue 92 East 64 th ST. Holland, MI 49423 800.205.7186 www.codeblue.com pg 2 of 2

PHYSICAL INFRASTRUCTURE SOLUTIONS Mini-Com Modular Faceplate Patch Panels Angled patch panels facilitate proper bend radius control and minimize the need for horizontal cable managers Accept Mini-Com Modules for fiber optic, UTP, and audio/video, which snap in and out for easy moves, adds, and changes CPPLA24WBLY CPPLA48WBLY CPPL24WBLY CPPL48WBLY C4PPLK Part Number ^ One rack space = 1.75" (44.45mm). M6 and #12-24 mounting screws included. Label versions available for easy port identification; replacement label/label covers available Mount to standard EIA 19" racks or 23" racks with optional extender brackets on page L.40 of SA-NCCB51 Part Description Mini-Com Angled Modular Patch Panels with Labels CPPLA24WBLY 24-port angled patch panel with labels, supplied with six factory installed CFFPL4 type front removable snap-in faceplates. CPPLA48WBLY 48-port angled patch panel with labels, supplied with twelve factory installed CFFPL4 type front removable snap-in faceplates. Mini-Com Modular Patch Panels with Labels CPPL24WBLY 24-port patch panel with labels, supplied with six factory installed CFFPL4 type front removable snap-in faceplates. CPPL48WBLY 48-port patch panel with labels, supplied with twelve factory installed CFFPL4 type front removable snap-in faceplates. Replacement Labels for Mini-Com Modular Patch Panels C4PPLK Replacement label/label cover kit for Mini-Com Modular Patch Panels with Labels (CPPL24WBLY, CPPL48WBLY, CPPL24WRBLY, CPPL48WRBLY) and Mini-Com Modular Furniture Faceplates with Labels (CFFPL4, CFPHSL4, CFFPEBSL4). Each kit contains six labels and six clear label covers per bag. No. of Rack Spaces^ Std. Pkg. Qty. Std. Ctn. Qty. 1 1 10 2 1 10 1 1 10 2 1 10 1 10 A. System Overview B. Copper Systems C. Fiber Optic Systems D. Power over Ethernet E. Zone Cabling F. Wireless G. Outlets H. Media Distribution I. Physical Infrastructure Management J. Overhead & Underfloor Routing Component Labels for Mini-Com Modular Faceplate Patch Panels K. Surface Raceway L. Cabinets, Racks & Cable Management Patch Panel Part Number All Patch Panels on this Page Suggested Label Solutions for TIA/EIA-606-A Compliance Laser/Ink Jet Desktop Printer Label TDP43ME Thermal Transfer Desktop Printer Label PanTher LS8E Hand-Held Printer Label Cougar LS9 Hand-Held Printer Label C261X035Y1J C261X035Y1T C261X035Y1C T038X000FJC-BK M. Grounding & Bonding N. Industrial For complete labeling solutions and product information, reference charts on pages O.1 O.18 of SA-NCCB51. For non-adhesive labeling solution, do not remove liner from label. O. Labeling & Identification P. Cable Management Accessories Q. Index www.panduit.com For service and technical support, call 866-405-6654 (outside the U.S. and Canada, see catalog back cover). C.59

Mini-Com TX6 PLUS UTP Jack Modules SPECIFICATION SHEET specifications Category 6/Class E, 8-position, UTP jack module shall terminate 4-pair, 22 26 AWG, 100 ohm unshielded twisted pair cable and shall not require use of a punchdown tool. UTP jack modules shall use a forward motion termination method to optimize performance by maintaining cable pair geometry while eliminating conductor untwist. The termination cap shall be color-coded white to designate Category 6 performance and shall include a universal label coded for T568A and T568B wiring schemes. technical information Category 6/Class E channel and component performance: 100% performance tested Confidence that each jack module will deliver the critical electrical performance requirements Utilizes enhanced Optimizes performance by eliminating conductor untwist and reduces Giga-TX Technology installation time and expense Improved termination cap Conductor retention slots simplify jack module termination Modular UTP jack modules snap in and out of all Mini-Com Faceplates, Modular Patch Panels and Surface Mount Boxes for easy moves, adds, and changes True strain relief Controls cable bend radius for long term installed performance Individually serialized Marked with quality control number for future traceability RJ45 interface Industry standard interface provides a quick and easy plug and play connection to RJ45 patch cords; backwards compatible Identification Can be clearly identified with optional labels and icons for port identification Keyed version available Color-specific keys with positive and negative keying features mechanically and visually distinguish connections to prevent unintentional mating with unlike keyed or non-keyed modular plugs, offering network design flexibility, versatility, accommodating discrete networks for enhanced security Termination tools (optional) EGJT termination tool ensures conductors are fully terminated by utilizing a smooth forward motion without impact on critical internal components for maximum reliability; TGJT termination tool ideal for high volume installations Block out device (optional) Provides a simple and secure method to control access to data ports while not in use Shuttered version (optional) Integrated shuttered door keeps out dust and debris of unmated RJ45 jack modules www.panduit.com Exceeds channel requirements of ANSI/TIA-568-C.2 Category 6 and ISO 11801 Class E standards at swept frequencies 1 to 250 MHz Exceeds component requirements of ANSI/TIA-568-C.2 Category 6 and ISO 11801 Class E standards at swept frequencies 1 to 250 MHz Meets all applicable ANSI/TIA-968-A requirements; contacts plated with 50 microinches of gold for superior performance FCC and ANSI compliance: IEC compliance: Meets IEC 60603-7 RoHS compliance: Compliant PoE compliance: Meets requirements of IEEE 802.3af and IEEE 802.3at for PoE applications UL rated: UL 1863 approved Conductor termination Wire cap compatible with 22 26 AWG solid or stranded cable with conductor range: insulation diameters of 0.060 in. max. and overall cable O.D. 0.200 in. to 0.330 in. key features and benefits applications Mini-Com TX6 PLUS UTP Jack Modules are a component of the TX6 PLUS UTP Copper Cabling System. This end-to-end system is interoperable and backwards compatible, providing design flexibility to protect network investments well into the future. With certified performance to the ANSI/TIA-568-C.2 Category 6 and ISO 11801 Class E standards, this system is ideal for today's high performance workstation applications. With certified performance to the ANSI/TIA-568-C.2 Category 6 and ISO 11801 Class E Edition 2.1 standards, these systems will support the following applications: Ethernet 10BASE-T, 100BASE-T (Fast Ethernet), 1000BASE-T (Gigabit Ethernet) 155 Mb/s ATM, 622 Mb/s ATM, 1.2 Gb/s ATM Token Ring 4/16 Digital video and broadband/baseband analog video Voice over Internet Protocol (VoIP) TX6 PLUS UTP Copper Cabling Systems Mini-Com TX6 PLUS UTP Jack Modules Jack module: CJ688TGIW* Shuttered jack module: CJD688TGIW* Keyed jack module: CJK688TG** TX6000 UTP Copper Cable Plenum: PUP6004*** Riser: PUR6004*** LSZH: PUL6004*** CM: PUC6004*** TX6 PLUS UTP Patch Cords CM (foot lengths): UTPSP^Y CM (meter lengths): UTPSP^^MY LSZH (meter lengths): UTPSPL^^MY Mini-Com Angled Modular Patch Panels 24-port, 1 RU: CPPLA24WBLY 48-port, 2 RU: CPPLA48WBLY Mini-Com Flat Modular Patch Panels 24-port, 1 RU: CPPL24WBLY 48-port, 2 RU: CPPL48WBLY For additional modular patch panels and punchdown patch panels, visit www.panduit.com Tools and Accessories Jack module termination tool: EGJT or TGJT Wire snipping tool: CWST Wire stripping tool: CJAST Clear dust cap: MDC-C Block out device: PSL-DCJB-^^^ Phone icons: CIPIW-C+ Data icons: CIDIW-C+ *To designate color other than IW (Off White), replace IW suffix with EI (Electric Ivory), IG (International Gray), AW (Arctic White), BL (Black), BU (Blue), RD (Red), YL (Yellow), GR (Green), OR (Orange), or VL (Violet). **To designate color, add suffix BL (Black), BU (Blue), RD (Red), YL (Yellow), GR (Green), or OR (Orange). Each color representing a different keyed configuration. ***To designate color, add suffix BU (Blue) or WH (White). For additional cable colors, contact customer service. ^For lengths 1 to 20 feet (one foot increments) and 25, 30, 35, 40 feet, change the length designation in the part number to the desired length. For standard cable colors other than Off White, add suffix BL (Black), BU (Blue), RD (Red), YL (Yellow), GR (Green), OR (Orange), or VL (Violet). For example, the part number for a blue 15-foot patch cord is UTPSP15BUY. ^^For lengths 1 to 10 meters (one meter increments) and 2.5, 15, 20, 25, 30, 35, 40 meters, change the length designation in the part number to the desired length. For standard cable colors other than Off White, add suffix BL (Black), BU (Blue), RD (Red), YL (Yellow), GR (Green), OR (Orange), or VL (Violet). For example, the part number for a blue 15-meter patch cord is UTPSP15MBUY. ^^^To designate color other than Red, add suffix Black (BL), Blue (BU), Yellow (YL), Green (GR), Orange (OR), Off White (IW) or International Gray (IG) at the end of the part number. 10/package. +To designate color other than IW (Off White), replace IW with EI (Electric Ivory), IG (International Gray), BL (Black), BU (Blue), RD (Red), YL (Yellow), GR (Green), OR (Orange), or VL (Violet) in the part number. 100/package. Contact customer service for bulk packaged and/ or keyed jack modules and patch cords. Downloaded from Elcodis.com electronic components distributor

Mini-Com TX6 PLUS UTP Jack Modules Test Results Mechanical Test Test Method Measurement Typical Test Results Normal Force Vibration IEC 512-6d Load (grams) Circuit Resistance (mohms) >100 <40 Shock IEC 512-6c Contact Disturbance (microseconds) <5 Durability IEC 512-9a Circuit Resistance (mohms) <40 Mating/Un-Mating IEC 512-13b Mating Force (N) <20 Un-mating Force (N) <20 Termination Cycles IEC 352 Number of Cycles >20 Electrical Test Test Method Measurement Typical Test Results Low Level Circuit Resistance Dielectric Withstand Voltage Insulation Resistance IEC 512-2a IEC 512-4a IEC 512-3a Resistance (mohms) 1000 V, 1 minute Resistance (mohms) <20 Passed >500 Environmental Test Test Method Measurement Typical Test Results Temperature Life IEC 512-9b Circuit Resistance (mohms) <40 Humidity IEC 512-11c Circuit Resistance (mohms) <40 Thermal Shock IEC 512-11d Circuit Resistance (mohms) <40 Climatic Sequence IEC 512-11a Circuit Resistance (mohms) <40 Flowing Mixed Gas Corrosion IEC 512-11g Circuit Resistance (mohms) <40 Jack Module Shuttered Jack Module.71 (18.06).62 (15.87) 1.50 (38.15) Dimensions are in inches (Dimensions in parenthesis are metric) WORLDWIDE SUBSIDIARIES AND SALES OFFICES PANDUIT CANADA Markham, Ontario cs-cdn@panduit.com Phone: 800.777.3300 PANDUIT EUROPE LTD. London, UK cs-emea@panduit.com Phone: 44.20.8601.7200 PANDUIT SINGAPORE PTE. LTD. Republic of Singapore cs-ap@panduit.com Phone: 65.6305.7575 PANDUIT JAPAN Tokyo, Japan cs-japan@panduit.com Phone: 81.3.6863.6000 PANDUIT LATIN AMERICA Jalisco, Mexico cs-la@panduit.com Phone: 52.33.3777.6000 PANDUIT AUSTRALIA PTY. LTD. Victoria, Australia cs-aus@panduit.com Phone: 61.3.9794.9020 For a copy of Panduit product warranties, log on to www.panduit.com/warranty Downloaded from Elcodis.com electronic components distributor For more information Visit us at www.panduit.com Contact Customer Service by email: cs@panduit.com or by phone: 800-777-3300 and reference COSP48 2010 Panduit Corp. ALL RIGHTS RESERVED. WW-COSP48 6/2010

GE Security Fiber Optic Data Transmitters and Receivers Overview The S714D and S7714D fiber links provide two-way transmission of 100Base-T Fast Ethernet data or 10Base-T Ethernet data. They combine the benefits of advanced engineering with the highest quality standards in the industry. These links are available as standalone modules or rack cards. The S714D operates over distances up to 11 mi (18 km). The S7714D operates over distances up to 28 mi (45 km). S714D models feature multimode operation, while S7714D models operate over single mode fibers. Secure Data Transmission The S714D and S7714D make it possible to add the security and efficiency of transmission over fiber to local area networks (LANs) and other Ethernet applications. Standard Features Two-way data transmission over one or two fibers Single and multimode models available Supports 100Base-T and 10Base-T Ethernet protocols Switch-selectable crossover Automatic polarity correction 18 db (single mode) or 13 db (multimode) optical budget Optical AGC SMARTS diagnostics Standalone and rack configurations Superior Diagnostics The SMARTS diagnostic technology provides constant monitoring of the link and the equipment connected to it. The status of the link and the system can be determined at a glance without the use of expensive test equipment. LED displays show transmitter and receiver status and activity. 100Base-T Fast Ethernet Data S714D and S7714D

GE Security U.S. T (561) 998-6100 T 888-GE-SECURITY 888-(437-3287) F 561 998 6224 Canada T 519 376 2430 F 519 376 7258 Asia T 852-2907-8108 F 852-2142-5063 Australia T 61-3-9239-1200 F 61-3-9239-1299 Europe T 44-113-238-1668 F 44-113-253-8121 Latin America T 305-593-4301 F 305-593-4300 www.gesecurity.com 2005 General Electric Company All Rights Reserved Specifications Data S714D (Multimode) S7714D (Single Mode) Channels 1 duplex Formats 100Base-T Fast Ethernet, 10Base-T Ethernet Baud Rate Compliant with IEEE 802.3 Bit Error Rate <1.0E-10 Optical Mode Multimode Single Mode Optical Budget* 13 db 18 db Emitter VCSEL Wavelength 850 nm and/or 1300 nm (depending on model) 1310/1550 nm (depending on model) Operating Distance** Up to 11 mi (18 km) Up to 28 mi (45 km) (depending on model and the timing characteristics of the input data signal) Transmitter Launch Power >-10 dbm >-6 dbm Receiver Sensitivity <-23 dbm <-24 dbm Gain Control Optical Automatic Gain Control (OAGC) Electrical Input Power 13.5 VDC regulated Current Requirement 300 ma Power Consumption 4.2 W Power Factor 3 Protection Solid-state short circuit protection Optional Power Supply Model 613P Environmental Operating Temperature Maximum Humidity -40 to 167 F (-40 to 75 C) 95% relative, noncondensing Related Diagram 100Base-T Data In/Out Transmitter Receiver 100Base-T Data In/Out Mechanical Dimensions (LWD), Standalone Units 5.0 x 2.8 x 1.5 (127 x 71 x 38 mm) Dimensions, Rack Units 1 slot (1.0 ) Weight Standalone 0.67 lbs (0.31 kg); Rack 0.55 lbs (0.25 kg) Construction Polycarbonate (standalone); Aluminum (rack) Optical Fiber Ordering Information Use the Configurators below to select the options available for these products. * Optical Budget based on 62.5 µm fiber, for 50/125 µm fiber subtract 3 db. ** Operating distance is approximate and assumes best fiber. It will be affected by the type and number of splices in the fiber. Refer to update No. TB00-005, which can be found at www.gesecurity.com As a company of innovation, GE Security reserves the right to change product specifications without notice. For the latest product specifications, visit GESecurity online at www.gesecurity.com or contact your GE Security sales representative. S714D-2006-09-2 imagination at work

AC Power For Business-Critical Continuity Liebert GXT3, 500VA -3000VA Models Reliable On-Line UPS Protection In A Compact 2U Package Liebert GXT3 is a true on-line UPS that delivers continuous, high-quality AC power to IT equipment with no break when transferring to battery. It protects equipment from virtually all power disturbances due to blackouts, brownouts, sags, surges or noise interference. The UPS is available in rack/tower and mini-tower configurations. One of the most affordable UPS systems in its class, Liebert GXT3 leads the industry in combining small size, high capacity and high reliability features: On-line design means zero transfer time from external to internal power. When utility power fails, your critical load remains supported by a seamless flow of power. Liebert GXT3 rated output power factor of 0.9 better matches up with switch-mode power supplies used in today s IT equipment. A higher output power factor allows for a more efficient utilization of the UPS. The UPS provides easy serviceability with user replaceable hot-swappable batteries. For maximum control, Liebert GXT3 is custom configurable to your needs using a specially designed Windows software package. Trade Compliance: Public sector customers may select from four capacities (1000, 1500, 2000 and 3000 VA, 120V) to provide TAA compliance. Refer to Liebert GXT3-GVG3 models. Ideally suited for: PCs Network workstations Servers Network closets Large network peripherals VoIP

Liebert GXT3 Standard Features The Proven Reliability Of True On-Line Operation Plus The Features You Need Most Although Liebert GXT3 requires just a slim 2U of rack space, it provides the capabilities of a physically larger system. Get up to 3kVA of capacity and battery backup, in 120V or 230V systems. External battery cabinets may be added for extended run time. On-Line UPS Protection for Essential and Critical Applications Dynamic Bypass Flexibility: Up To Six Battery-Backed Outlets A generous quantity of battery-backed outlets allows more equipment to be protected by the UPS. Rotatable Display Panel The LED display panel rotates 90 to make the readout of the LED display easy to see in rack or tower position. Automatic Frequency Sensing The UPS automatically adjusts to the input frequency, 50Hz or 60Hz. Mounting Flexibility Optional telescoping rack rails mount to the sides of the UPS for easy installation into a rack enclosure. A standard tower support base ships with the UPS. Utility Surge Suppression Power Factor Correction/Rectifier Charger Inverter Load Battery Liebert GXT3 is a true on-line power source, so whatever the quality of power coming in, the pure sinewave output meets the exacting standards of your equipment. Liebert GXT3 includes: Power factor correction Internal batteries Frequency conversion Internal automatic bypass to utility in case of adverse UPS conditions Manual bypass capability Support for up to four external battery cabinets (rack/tower models) Liebert GXT3 handles all these potential power problems: Power spikes and transients EMI/RFI noise Voltage sags and brownout conditions Harmonics Power-factor corrected loads Outages Frequency variations Liebert GXT3 is easily configured for either rackmount or tower applications. The LED display rotates for easy viewing in either orientation. 2

Liebert GXT3 contains internal batteries, and is also able to support up to four external battery cabinets also 2U size. Higher Availability: Advance Early Warning of UPS System Status Multiple audible and visual alarms immediately alert you to an output overload, low battery, bypass, battery discharge, battery loss or replace battery condition. 4-8 minutes of Battery Backup Time at Full load Provides ample time for an orderly shutdown of connected equipment when utility power fails. Optional matching external battery cabinets offer additional backup time. Overload Capability Designed to handle output overload conditions. Full Sequenced Battery Testing Provides automatic and manual self-diagnostic battery testing capabilities. This provides a comprehensive analysis of the condition of the batteries within the UPS and will notify you when the internal batteries need to be replaced. User Replaceable Hot Swappable Batteries Easy to replace batteries increase product life and provide prolonged UPS reliability. Batteries are conveniently located behind the front bezel of the unit. Lowest Total Cost Of Ownership: 0.9 Output Power Factor Liebert GXT3 rated output power factor of 0.9 better matches up with switchmode power supplies used in today s IT equipment. A higher output power factor allows for a more efficient utilization of the UPS. Wide Input Voltage Window Prolongs battery life by allowing the UPS to maximize the use of utility power before transferring to battery when input voltage exceeds specified limits. Intelligent Fan Operation Automatically changes rotation speed depending on system requirements to decrease power consumption and noise. Efficient Operation 88% AC-AC, minimum. Power-Factor Correction Prevents noise, harmonics and distortion from being passed on to connected loads or from being fed back to the utility. Internal Automatic and Manual Bypass Capability Assures continuity of power to critical loads during system problems or maintenance. Intelligent Battery Management Includes efficient three-stage charging technique and comprehensive discharging protection that extends battery life for greater availability. Input Circuit Breaker Provides increased protection to ease recovery from overloads. Lightning and Surge Protection The transient voltage surge suppression (TVSS) circuitry inside Liebert GXT3 provides additional protection for the connected equipment from incoming spikes, surges, and other power anomalies present on the incoming utility power source. Warranty Protection The industry s best warranty No-hassle two-year warranty with UPS replacement in the event of problems. Shipping is free for both original UPS return and the replacement unit. Optional one-year and three-year extensions also available. Multiple Choices For Communication, Shutdown And Reporting: SNMP And Web-Based Communication Options Liebert IntelliSlot Web Card provides SNMP (including SNMPv3) and IPv.6 and web-based management to your Liebert GXT3. Provides SNMP MIB to monitor and control your UPS from your network management station or any PC running Microsoft Internet Explorer. Network shutdown Sends both SNMP traps and emails for event notification, and automatically emails a daily UPS history Auto-senses 10M/100M Ethernet Compatible with shutdown software to ensure graceful computer shutdown The Liebert GXT3 is also fully compatible with: Liebert MultiLink shutdown software included with the Liebert GXT3 UPS Liebert Nform monitoring software Liebert Multiport multiplexing unit Liebert Intellislot Relay Interface Card USB Communications Windows (98 and later) built-in power management functions provide monitoring of UPS status and manage the automatic orderly shutdown of the computer if a power outage ever exceeds the battery capacity of the UPS. Liebert MultiLink shutdown software can also be used via USB connection. Optional Liebert MicroPOD Output Distribution And Maintenance Bypass Module When your computer system can t be without power, even for scheduled UPS maintenance, the Liebert MicroPOD Maintenance Bypass and Output Distribution Unit ensures continuous uptime. It allows you to manually transfer connected equipment to utility power via a maintenance bypass switch, permitting scheduled service or UPS replacement without the need to shut down connected equipment. Features include: 2U height minimizes rack space requirements Installs with plug-and-play ease Two-year, no-hassle replacement warranty Liebert MicroPOD Liebert GXT3 minitower model provides 1000VA capacity in a compact design. 3

Specifications Model Number GXT3-500RT120 GXT3-700RT120 GXT3-1000RT120 or GVG3-1000RT120 GXT3-1000MT120 Model Rating VA/W 500/450 700/630 1000/900 1000/900 Dimensions: in. (mm) DxWxH 19.7x16.9x3.4 (497x430x85) Weight: lbs. (kg) 44 (20) 15.4x6.9x8.9 (390x175x225) Input AC Parameter Voltage Range 120VAC nominal; variable based on output load Frequency 40Hz ~ 70Hz; Auto Sensing Input Power Cord 10 ft. attached w/ NEMA 5-15P plug Output AC Parameter Output Receptacles 5-15R x 6 Voltage 110/115/120/127VAC (user-configurable); ±3% Waveform Sine wave Battery Full Load 12 minutes 6 minutes 5 minutes 5 minutes Half Load 30 minutes 14 minutes 15 minutes 15 minutes Recharge Time 3 Hours to 90% capacity after full discharge with 100% load till UPS auto-shutdown Agency Safety UL 1778, cul Listed RFI/EMI FCC Part 15, Class A=CISPR22 Class B Surge Immunity IEC 62040-2 2nd Ed Transportation ISTA Procedure 1A Model Number GXT3-1500RT120 or GVG3-1500RT120 GXT3-2000RT120 or GVG3-2000RT120 GXT3-3000RT120 or GVG3-3000RT120 GXT3-3000RT208 Model Rating VA/W 1500/1350 2000/1800 3000/2700 3000/2700 Dimensions: in. (mm) DxWxH 19.7x16.9x3.4 (497x430x85) 23.7x16.9x3.4 (602x430x85) Weight: lbs. (kg) 48.5 (22) 52.9 (24) 61.7 (28) 61.7 (28) Input AC Parameter Voltage Range Frequency Input Power Cord 10 ft. attached w/ NEMA 5-15P plug 120VAC nominal; variable based on output load 10 ft. attached w/ NEMA 5-20P plug 40Hz ~ 70Hz; Auto Sensing 10 ft. attached w/ NEMA L5-30P plug 208VAC nominal; variable based on output load 10 ft. attached w/ NEMA L6-20P plug Output AC Parameter Output Receptacles 5-15R x 6 5-20R x 6 L5-30Rx1+5-20Rx6 L6-20Rx1+L6-15Rx2 Voltage 110/115/120/127VAC (user-configurable); ±3% Sine wave 208/220/230/240 VAC (user-configurable); ±3% Waveform Battery Full Load 5 minutes 4 minutes 4 minutes 4 minutes Half Load 16 minutes 11 minutes 14 minutes 14 minutes Recharge Time 3 Hours to 90% capacity after full discharge with 100% load till UPS auto-shutdown Agency Safety UL 1778, cul Listed RFI/EMI FCC Part 15, Class A=CISPR22 Class B Surge Immunity IEC 62040-2 2nd Ed Transportation ISTA Procedure 1A GVG: TAA Compliant versions. Emerson Network Power Liebert Corporation World Headquarters 1050 Dearborn Drive P.O. Box 29186 Columbus, Ohio 43229 United States Of America 800 877 9222 Phone (U.S. & Canada Only) 614 888 0246 Phone (Outside U.S.) 614 841 6022 FAX Contact@EmersonNetworkPower.com Emerson Network Power Caribbean and Latin America Office United States of America +1-954-984-3452 Phone Ask.Cala@Emerson.com Emerson Network Power European Headquarters Office Italy +39 049 9719 111 Phone +39 049 5841 257 FAX Marketing.EMEA@EmersonNetworkPower.com Emerson Network Power Asia Pacific Office Phillipines +63 2 687 6615 +63 2 730 9572 FAX Marketing.AP@Emerson.com liebert.com 24 x 7 Tech Support 800 222 5877 Phone 614 841 6755 (outside U.S.) While every precaution has been taken to ensure accuracy and completeness in this literature, Liebert Corporation assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. 2012 Liebert Corporation. All rights reserved throughout the world. Specifications subject to change without notice. All names referred to are trademarks or registered trademarks of their respective owners. Liebert is a registered trademark of the Liebert Corporation. SL-23182 (R07/12) Emerson Network Power. The global leader in enabling Business-Critical Continuity. AC Power Connectivity DC Power Embedded Computing Embedded Power Infrastructure Management & Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Printed in USA Surge Protection