Owners Manual Three-Way Architectural Speaker www. artcoustic.com
Architect SL Three-Way Architectural Speaker Features: - X2 bass system, extended low frequency - Extremely small and compact design - low distortion - low power consumption - Wide frequency response 55Hz to 40kHz - Fast, easy and simple installation - Suitable for a wide range of application, from HiFi Systems, Multi Room Systems and smaller Home Cinemas Architect SL Overview: Architect SL Series - Created to provide impressive sound from ultra thin and aesthetic pleasing loudspeakers, the entire Architect line of in-wall/inceiling loudspeakers will surprise you. Whether you are looking for true Hifi music reproduction, or louder applications, such as home cinema installations, commercial installations, bars, restaurants and public address solutions, The Artcoustic Architect Series offers the ultimate solution. Components Overview: High Frequency driver: Dual Ring Radiator diaphragm with highly linear suspension and low loss surrounds for high clarity and clean transient response. Copper caps for better HF extension and lower distortion and wave-guide center plug, copper-clad aluwire Woofer: Extra long excursion and Aluminum Short Circuiting Ring, 4-layer voice coil, anodized aluminum for improved heat dissipation, combined with Distortion Reduced Motor Crossover: 6 db/octave low pass and 12 db/octave high pass filter The Architect Series has been designed and Engineered with same high specifications as all the other Artcoustic models, leaving no space for compromise on sound quality and built. The Architect series consist of two models, Architect 2-1 SL single source 3-way full range speaker to the larger Architect 4-2 SL single or dual source 3-way full range speaker. Partner it with an Artcoustic Subwoofer for a truly full range, dynamic performance. Side View Vertical Phase aligned Dispersion :
Specification Architect 2-1 SL Architectural Speaker Three-Way Architectural Speaker Transducer: LF-MF 2 x 3 inch cone HF 1 x 1 inch Dual Ring Radiator Crossover: Low Pass Filter 6 db/octave 1000 Hz High Pass 12 db/octave 4000Hz Connection: Single amped Gold Plated Push Terminals Performance: - Operating Range 55 Hz (-3dB) to 40 khz - Nominal Beamwidth Horizontal 90 Vertical 90 - Axial Sensitivity (whole space SPL) LF/MF-HF Sensitivity 88 db - Input Impedance Nominal Minimum 4 ohms - Calculated Axial Output Limit (whole space SPL) Average Peak LF/MF-HF 104dB - Maximum Power Handling 50 Watt - Weight 2 kg - Dimensions H: 230 W: 230 D: 70 mm - Dimensions (grille) H: W: D: 9 mm Finish: Silk Paint, White and RAL colours Grille options: Match System and Pantone Specification Architct 4-2 SL Architectual Speaker Transducer: LF-MF 4 x 3 inch cone HF 2 x 1 inch Dual Ring Radiator Crossover: Low Pass Filter 6 db/octave 1000 Hz High Pass 12 db/octave 4000Hz Connection: Single or bi- amped Gold Plated Push Terminals Performance: - Operating Range 55 Hz (-3dB) to 40 khz - Nominal Beamwidth Horizontal 90 Vertical 90 - Axial Sensitivity (whole space SPL) LF/MF-HF Sensitivity (stereo) 88 db (mono) 94dB - Input Impedance Nominal Minimum 4 ohms - Calculated Axial Output Limit (whole space SPL) Average Peak LF/MF-HF (stereo) 104dB (mono) 110dB - Maximum Power Handling 50 Watt - Weight 4 kg - Dimensions H: 290 W: 290 D: 70 mm - Dimensions (grille) H: 320 W: 320 D: 9 mm Finish: Silk Paint, White and RAL colours Grille options: Match System and Pantone
Architect 2-1 SL Three-Way Architectural Speaker 76 70 56 95 Square cut Round cut 208 230 Longer screws 208 230 6 208 19 9 9 90 degree angled grille Facet grille Architect 4-2 SL Three-Way Architectural Speaker 76 Square cut 70 56 95 259 290 Longer screws 240 259 290 6 240 9 320 9 320 Facet grille 320 90 degree angled grille 320
Architect 2-1 SL with 90 degree angled grille Architect 4-2 SL with 90 degree angled grille Architect 2-1 SL with facet grille Architect 4-2 SL with facet grille www. artcoustic.com
Artcoustic Architect mounting method, ceiling thickness max. 18mm. for ceiling plate thickness up to 36mm. use supplied set of longer screws Step 1 Unscrew screw 1 untill max. Leave screw inside insert 1 2 Unscrew screw 2 until it slip off the insert and angle mounting bracket as shown in step 1 Step 2 Tighten screw 1 3 Step 3 4 Tighten screw 2 www. artcoustic.com