ARCS Pre-Implantology

Transcription

1 ARCS Pre-Implantology ARCS - Alveolarkamm Reconstruction System The ARCS System meets the requirements of modern implantology. Atrophy of the alveolar crest causes continuous problems during restoration with dental implants in patients where there is not enough bone to locate the implants securely. The lack of bone can be overcome by using autologous bone grafts for example. One easy method to fix the bone graft is by using these micro screws, either alone or in combination with titanium micromesh. Three dimensional alveolar crest reconstruction System for fixation of: Bone blocks, Titanium Mesh, Sinus Implant Stabilizer, Micro Plates and Distractors. Highly biocompatible implant material Rapid and less resorbing bone regeneration Possibility of using autologeous bone only Very low infection risk OMF / Oral Maxillo Facial

2 ARCS Table of Contents Screws Page 3-4 Microplates, Titanium MICRO-MESH Page 5 Titanium Membranes Page 6 Drills Page 7-8 Instruments Page 9-10 SIS - Sinus Implant Stabilizer Page 11 SWING-LIFT Instruments Page 12 ARCS PIN Page Container Page 15 The ARCS System ist compatible to the MONDEAL MICRO 1200 Microplate Osteosynthesis-System. Page 2

3 Self-tapping Screws Standard (Packaging: 5/ea.) LOCK-DRIVE Screw Art. No. Diameter x Length x 3 mm x 4 mm x 5 mm x 6 mm x 7 mm x 8 mm x 11 mm x 13 mm x 15 mm CROSS-FIT Screw Art. No. Diameter x Length x 3 mm x 4 mm x 5 mm x 6 mm x 7 mm x 8 mm x 11 mm x 13 mm x 15 mm LOCK-DRIVE Emergency Screw Art. No. Diameter x Length x 4 mm x 6 mm x 11 mm x 13 mm x 15 mm CROSS-FIT Emergency Screw Art. No. Diameter x Length x 4 mm x 6 mm x 11 mm x 13 mm x 15 mm Page 3

4 Self-drilling Screws Advanced (Packaging: 1/ea.) Self-drilling Screws with suitable thread component for bone anchorage Flat shaft for the transplant Approved titanium implant quality CROSS-FIT Screw, self-drilling MCD Screw, self-drilling Art. No. Diameter x Length x 8 mm x 10 mm x 12 mm x 14 mm Art. No. Diameter x Length x 8 mm x 10 mm x 12 mm x 14 mm Page 4

5 Microplates (Packaging: 1/ea.) Thickness: 0.6 mm hole Plate straight hole X-Plate More microplates please find in our brochure MICRO Titanium MICRO-MESH (Packaging: 1/ea.) MICRO-MESH, Thickness: 0.1 mm MICRO-MESH, Thickness: 0.2 mm Art. No. Length x Width x Thickness x 30 x 0.1 mm x 60 x 0.1 mm x 30 x 0.1 mm x 60 x 0.1 mm x 120 x 0.1 mm Art. No. Length x Width x Thickness x 30 x 0.2 mm x 60 x 0.2 mm x 30 x 0.2 mm x 60 x 0.2 mm x 120 x 0.2 mm Indications: Stable covering of medium and large bone defects after filling with autologeous bone grafts or with bone substitute materials. Duration of implantation of the Titanium Mesh: approx. 3-4 months. Page 5

6 Titanium Membranes (Packaging: 1/ea.) Art. No. Length x Width x Thickness x 25 x 0.02 mm x 25 x 0.02 mm x 25 x 0.02 mm x 25 x 0.02 mm Indikations: Covering of medium and small bone defects as barrier between the mucosa and the bone for the unilateral bone regeneration (tenting procedure) also when using bone substitute materials. Duration of implantation of the Titanium Membrane: approx. 2-4 months. ARCS Titanium Membrane, micro-perforated Art. No. Length x Width x Thickness x 30 x 0.03 mm TI-PORE Membrane: Ti-Pore membranes distinguish to normal membranes by the micro-perforation in the centre of the membrane. The special features secure the volume of the augmentation and offer an optimized stability of the augmented bone for perfect aesthetic results. Both Titamium membranes can be cut to individual form and size! Page 6

7 Drills Max rpm for Screws Standard For straight handpiece Art. No. Diameter x Length Working Length (WL) End x 47 mm 5 mm Dental x 50 mm 8 mm Dental Drill Gliding Hole Art. No. Diameter x Length Working Length (WL) End x 49 mm 10 mm Dental For angled handpiece Art. No. Diameter x Length Working Length (WL) End x 20 mm 5 mm Dental x 23 mm 8 mm Dental x 25 mm 10 mm Dental x 30 mm 15 mm Dental For the drilling of the gliding hole in the bone graft Art. No. Diameter x Length Working Length (WL) End x 25 mm 10 mm Dental x 22 mm 9 mm Dental x 33 mm 20 mm Dental Page 7

8 Drills Max rpm for Screws Advanced Art. No. Diameter x Length Working Length (WL) End x 25 mm 10 mm Dental Optional Art. No. Diameter x Length Working Length (WL) End x 25 mm 10 mm Dental x 30 mm 15 mm Dental Page 8

9 Instruments for Screws Standard Screwdriver handle, 9 cm Screwdriver handle, short, 6 cm LOCK-DRIVE blade CROSS-FIT blade CROSS-FIT screwdriver with holding device CROSS-FIT holding device, not self-retaining LOCK-DRIVE, screwdriver fixed, 13 cm, self-retaining CROSS-FIT, screwdriver fixed, 13 cm, self-retaining Page 9

10 Instruments for Screws Standard LOCK-DRIVE blade, short, 2 cm, DENTAL, self-retaining CROSS-FIT Klinge, short, 2 cm, DENTAL, self-retaining Thumb Screw Mandrel for Dental shaft instruments for Screws Advanced Screwdriver handle, 10 cm CROSS-FIT blade MCD blade Page 10

11 SIS - Sinus Implant Stabilizer (Packaging: 1/ea.) acc. to Prof. Dr. M. Lang, Nürnberg The implant and the healing screw must have a diameter larger than 3.3 mm (respectively 3.6 mm). Depending on the implant system and implant diameter the SIS-Version Standard or SIS-Version large should be used. Handling: The SIS is fixed between the implant and the healing screw. This combination can additionally be secured with ARCS Microscrews through the small SIS holes inside the bone. To be used with following endosseus implants (without guarantee): Branemark - Nobel Biocare, Osseotite 3i - Implant Innovations, Ankylos - Friadent Dentsply, Bonefit-Straumann, Replace - Nobel Biocare, Camlog-Altatec, Xive - Friadent Dentsply, Sky Implant - Bredent, u.a. Plate thickness: 0.6 mm Ø SIS Sinus Implant Stabilizer, standard Ø SIS Sinus Implant Stabilizer, standard, curved Ø SIS Sinus Implant Stabilizer, large Ø SIS Sinus Implant Stabilizer, large, curved Drill guide, 1/ea. (2 ea. recommended) Page 11

12 SWING-LIFT Instruments The SWING-LIFT Instrument set for the direct sinus-lift increases the sensitivity during operation and reduces the risk of perforating the Scheiderian membrane - due to the unique swing-effect of the instruments no. 1, 2 and Swing-Lift instrument no.1, small hook, angled Swing-Lift instrument no. 2, hook, angled Swing-Lift instrument no. 3, spatula, straight/angled Swing-Lift instrument no. 4, spoon/condenser Swing-Lift Set, instruments I-4, complete (not illustrated) Page 12

13 ARCS PIN Titanium Pins 3 mm, with thread, 5/ea Titanium Pins 3 mm, without thread, 5/ea Titanium Pins 5 mm, with thread, 5/ea Titanium Pins 5 mm, without thread, 5/ea Drill for pins and foils, DENTAL Blade for Titanium Pins, DENTAL Tray for 15 Titanium Pins Thumb Screw Mandrel for Dental shaft instruments ARCS Membrane Perforator and spatula, 18 cm Mallet for placing the pins, 140 g, 21 cm Page 13

14 ARCS PIN Pin Placement Instrument straight, complete, 3 parts Pin Placement Instrument angled, complete, 3 parts Handle for Placement Instrument Placement adaptor straight for Placement Instrument, with cover cap Placement adaptor angled for Placement Instrument, with cover cap Cover cap for Placement Instrument Page 14

15 Container 31-TD ARCS tray for instruments and implants Page 15

16 High Quality Implants Made by MONDEAL We reserve the right to make catalog and design changes arising from further developments and modifications. Pictures, product descriptions and texts are the property of MONDEAL Medical Systems GmbH. Further use and reproduction by Third Parties requires written consent from MONDEAL Medical Systems GmbH. All rights reserved! Note: Responsibility for the selection of the patient, for adequate training as well as the decision as to the choice and use of the implants, a post-operative removal or retention of implants is the sole decision of the surgeon. All brands and logos referred to in this brochure, registered by Third Parties, are subject without restriction to the legal provisions currently in force and to the rights of ownership of the respective registered owner MONDEAL Medical Systems GmbH Am Gewerbering Mühlheim a. d. Donau/Germany Phone Fax mail@mondeal.de 97-D105-E ARCS 01/ 04-11