PREPARATION. INTERNAL CALIBRATION (No external weight needed.) SPAN CALIBRATION

Transcription

1 Calibration Guide PREPARATION Adventurer Pro Adventurer Pro balances have two calibration methods: Span and Linearity. Some models have Internal Calibration (InCal ) for Span calibration. Ensure that the scale is level, stable, and undisturbed during calibration. (Otherwise the process could fail.) Allow scale to warm up for five minutes after stabilizing to room temperature. Use suitable calibration masses (available from Ohaus). Exact weight value depends on model. Follow prompts for indicated values to use. (Weight values here are examples only.) Calibration may be locked out. To unlock it, use the Unlock menu. If the scale is set to Legal for Trade operation, a seal must be broken to unlock it. (See the Instruction Manual.) Note: To cancel calibration, press: INTERNAL CALIBRATION (No external weight needed.) 1 1 When calibration finishes, balance returns to currently selected mode. SPAN CALIBRATION (If InCal appears press No.) 1 1 (Acquiring zero value) 1 (Place weight on pan.) (If SPAN DONE flashes, remove mass from Pan.) (Press No to change.) Balance returns to weighing mode. Ohaus Corporation i Adventurer Pro Calibration Guide

2 Adventurer Pro Calibration Guide LINEARITY CALIBRATION: (If InCal appears press No.) 1 1 (Acquiring zero value) (Place weight on pan.) (Flashes while establishing weight value.) (Place weight on pan.) (Flashes while establishing weight value.) Remove weight from pan, and press: *80230* P/N Adventurer Pro Calibration Guide ii Ohaus Corporation

3 Calibration Guide CS Series Scales PREPARATION CS Scales can be calibrated as follows. Follow the prompts for calibration mass values. Ensure that the scale is level, stable, and undisturbed during calibration. (Otherwise the process could fail.) Allow scale to warm up for five minutes after stabilizing to room temperature. Use suitable calibration masses (available from Ohaus). Note: To cancel calibration, long-press: CALIBRATION 1 (Acquiring zero value) CAL -C- (Place weight on pan.) 1 C 200 -C- If calibration successful: PASS If calibration fails: CAL E If CAL E appears, turn the scale off and try again. Be sure to have the appropriate calibration weight. *802303* P/N Ohaus Corporation i CS Series Scales Calibration Guide

4 Calibration Guide Pioneer Balances PREPARATION Pioneer balances have two calibration methods: Span and Linearity. Some models have Internal Calibration (InCal ) for Span calibration. Ensure that the scale is level, stable, and undisturbed during calibration. (Otherwise the process could fail.) Allow scale to warm up for five minutes after stabilizing to room temperature. Use suitable calibration masses (available from Ohaus). Exact weight value depends on model. Follow prompts for indicated values to use. (Weight values here are examples only.) Calibration may be locked. To unlock it, use the Unlock menu. (See Instruction Manual.) Note: To cancel calibration, press: until scale turns off. INTERNAL CALIBRATION (No external weight needed.) (Two screens flash alternately.) (Flashes continuously while calibration proceeds.) Balance returns to weighing mode. SPAN CALIBRATION (If InCal appears press No.) 1 1 (Place weight on pan.) (Press No to choose alternate weight.) (Remove the mass from the Pan.) Balance returns to weighing mode. done Ohaus Corporation i Pioneer Balances Calibration Guide

5 Pioneer Balances Calibration Guide LINEARITY CALIBRATION: (not available on InCal models) (If InCal appears press No.) 1 (Place weight on pan.) (Remove the mass from the Pan.) (Acquiring zero value) (Place weight on Pan.) (Remove the mass from the Pan.) (Recalculating zero value) done Balance returns to weighing mode. * * P/N Pioneer Balances Calibration Guide ii Ohaus Corporation

6 Quick Start Guide PREPARATION FOR USE Release Shipping Lock on top of the balance Turn the pointer 90 counter-clockwise. Install the Platform Rectangular platform: Place diagonally on subplatform and rotate counter-clockwise until it locks. Round platform: Set straight down on subplatform. Scout Pro Balance Locked position Pointer Unlocked position Subplatform Draft Shield models: Position draft shield on top and rotate it until it faces forward. Connect Power Adapter jack Ensure voltage identification label matches local line voltage. If not, do not connect the unit. Contact Ohaus or your dealer. Battery Installation Install the Four AA batteries with polarity as shown in the battery compartment. Balances with leveling feet and bubble must be leveled before using. (Bubble is at rear, next to AC Adapter Input Jack.) SELECTING THE LOCATION: Place on a firm, steady surface with sufficient space. Avoid excessive air current, vibrations, heat sources, or rapid temperature changes. SAFETY PRECAUTIONS Before plugging in the balance, verify that local power supply matches voltage printed on power adapter. (Use only the adapter provided with the balance.) Disconnect the balance from the power supply when cleaning. Do not operate this product in hazardous or unstable environments. Do not drop loads on the pan. Use only approved accessories and peripherals, as available. Operate the product only under ambient conditions specified in the Instruction Manual. Service should be performed by authorized personnel only. Ohaus Corporation i Scout Pro Balance Quick Start Guide

7 Scout Pro Balance Quick Start Guide CONTROLS Battery charge indicator Symbols for weighing modes: G Specific Gravity N Newtons % Percent PC Pieces kg Kilograms, g grams dwt (not used) lb:oz (not used) ct (not used) t Totalize mode (or taels*) *Unit varies by model Stability indicator Button ON/ZERO Off PRINT Menu Functions Short Press (when off) Short Press:(when on) Long Press Extended Long Press Short press in Menu mode Short Press Press and Hold Short press in Menu mode Turns scale on. If balance is on, sets display to zero. Turns scale off. During power up, enters Menu mode. Accept setting on display. Sends print command to COM interface port. If Display Hold or Totalize mode is active, short press enters that mode. Scroll through Units. Release on desired unit. No (toggles through available settings) Locking the Menu The Lock Switch is used to lock out the menu mode, preventing unauthorized changes. To lock the menus, position the Lock Switch next to the tab on the bottom of the balance as shown. Locked Unlocked Scout Pro Balance Quick Start Guide ii Ohaus Corporation

8 Quick Start Guide Scout Pro Balance OPERATION Weighing Start with the balance on. 1 (Rezero the display) (Place sample on platform) (Example 0g) Taring a Container s Weight Taring zeros the container weight. With balance on, place an empty container on the platform. (Container weight) 1 (Container weight tared) (Place material in container) (Material and container removed) (0g sample) To remove tare, press ON/ZERO Off again. ADDITIONAL OPERATIONS Use the Units Menu to activate Parts Counting or Percent Weighing. (See back page.) To enable Display Hold, Totalize and Specific Gravity, use the Setup/Mode submenu. Parts Counting has two modes: (See Instruction Manual for more details.) Normal: balance determines quantity based on average weight of parts in original reference quantity. Enhanced: additional parts can be added to the platform ( the original number). The additional reference quantity produces a more accurate average part weight. Percent Weighing: place a reference weight on the balance, then view other loads as a percentage of the reference. The reference weight equals100%. Display-Hold mode captures and stores the highest stable value. When displayed, the stability indicator blinks. Note: Units cannot be changed when in Display-Hold mode. Totalize allows storage of a series of weight measurements. Totalize mode has been initiated when t and the current unit are displayed together. When totalized weight is shown, the t indicator blinks. Note: Units cannot be changed when in Totalize mode. The Specific Gravity mode allows calculating the specific gravity of a sample. (SPEC.GR mode must be turned ON before removing platform and installing hook.) Ohaus Corporation iii Scout Pro Balance Quick Start Guide

9 Scout Pro Balance Quick Start Guide MENU NAVIGATION There are four main menus in the balance:.c.a.l.,.s.e.t.u.p.,.u.n.i.t.s. and.e.n.d. (Start with the balance off and the Lock Switch off: see page ii). The sequence is shown below. 1 (Acquiring zero value) (Weigh Mode) MENU STRUCTURE Accepting/Bypassing Menu Items Start with menu item displayed = YES Accept = NO (Short presses advance through menu) Cal Yes/No Setup Auto-Off Lin Cal -Yes/No Mode -Hold -Totalize -Specific Gravity Off End -Yes/No Units g kg oz lb PC -Count -Cnt.Enh Off % End -Yes/No End Yes/No * * P/N Scout Pro Balance Quick Start Guide iv Ohaus Corporation

10 Quick Start Guide YA Gold Series PREPARATION FOR USE The YA Gold Series scale comes fully assembled, except for battery installation. Use two high quality AAA batteries: insert in sequence, both in positive direction, as shown: AAA + + Allow at least seconds warm-up time, for scale to stabilize before operation. PROPER ENVIRONMENT For dependable operation of this product, observe the following precautions: Avoid exposure to extreme heat or cold. Allow at least one hour stabilization after temperature change. Keep the scale in a clean environment. Dust, dirt, moisture, vibration, air currents, or proximity to other electronic equipment could adversely affect reliability and accuracy. Avoid shaking, dropping, or shocking the scale. Do not operate this product in unstable environments. Only operate the scale on a stable, vibration-free surface. Gently place items to be weighed on the platform. Rough treatment could damage the internal components. DISPLAY Tare mode (container weighing) Negative sign Symbols for: Grams, Ounces, Carats, Grains, Pieces (not used) Zero mode (standard weigh) Ohaus Corporation i YA Gold Series Pocket Scales Quick Start Guide

11 YA Gold Series Quick Start Guide OPERATION Place the scale on a horizontal flat surface. Press ON/OFF. Wait until 0.00 appears. Press MODE to switch weighing units: g-grams, oz-ounces, ct-carats or gngrains. Put the item to be weighed on the platform (eg,.1 carats). TARE: Turn on the scale as described above. Place a container on the platform (eg,.2 grams). Press TARE. The display shows 0.00 with TARE at left. Add material to the container (eg, 2 grams). Display shows weight of material not the container. When container and material are removed, display will show weight of container as negative value. ADDITIONAL OPERATIONS CHANGING UNITS OF MEASURE: Press Mode to toggle among four choices. Default: Grams g Press Mode once to choose Ounces oz Press Mode again to choose Carats ct Press Mode again to choose Grains gn * * P/N YA Gold Series Pocket Scales Quick Start Guide ii Ohaus Corporation