EMBEDDED WEB SERVER CONFIGURATION TO ENABLE AUTOSEND AND OUTGOING FOR HP QUICKPAGE

Transcription

1 EMBEDDED WEB SERVER CONFIGURATION TO ENABLE AUTOSEND AND OUTGOING FOR HP QUICKPAGE INTRODUCTION To ensure accurate billing, the HP QuickPage program requires collection of the metered information from the printers and multifunction products (MFPs) under contract. HP AutoSend, a standard feature in the device firmware on many workgroup HP LaserJets, can be used to provide this capability. This document provides a step-by-step guide to configure HP AutoSend on HP printers and MFPs. IMPORTANT NOTE It is essential that you follow all steps in this document and that the proper address for sending the AutoSend report is entered into the AutoSend Destinations box in the final step. CONFIGURATION STEPS Prerequisites 1. Identify the IP address of the printer/mfp: Navigate through the menu in the display panel of the device and print the configuration page. The IP of the device can be found under the networking section or under the Embedded JetDirect section. 2. Gather SMTP server details (server name, port, user name, and password if authentication is required). This can be obtained from the IT admin of the client. This information is vital for AutoSend to function. Section 1 Use the following steps to configure HP AutoSend on HP printers and MFPs. NOTE Please refer to Section 2 for the following printers: HP Color LaserJet CM4540 MFP HP Color LaserJet CP5520 series 1. Launch a browser (Internet Explorer 6.0 or greater) and connect to the device home page (for example, a) Navigate to Settings > server and select Enable outgoing to configure the server. b) Provide the SMTP server IP and port (if asked) along with the domain name. Use 25 for the port if no other is evident. NOTE On some models you will not see an input box for Port. c) If the SMTP server requires authentication, provide the username and password. d) The Return Address is required. The username must be the word device and the customer network domain name should be entered into the Domain Name field. Example: If the domain name is HP.com, Device address would be device@hp.com. e) Click Apply. 1

2 2. After setting the SMTP server details: a) Navigate to Settings > AutoSend. b) Select Enable AutoSend and configure to send every 1 day (as shown below). c) Provide the destination address: meterinfo_xx@clearingoffice.com. Replace the XX (as shown here) with the 2-letter code for your country-specific address. To find the country-specific code, please refer to the table of addresses at the end of this document. d) Click Test then Apply. IMPORTANT NOTE To ensure the SMTP server passes the to external destinations, please provide a test external address (such as a Yahoo, Gmail, Hotmail, or other web-based account other than the internal company account). Click Test and check for the receipt of an message in the test address specified confirming the compatibility of the SMTP server. If an error message is shown at the AutoSend page or if the does not reach your test account, verify with your customer technical contact (IT) that the SMTP gateway is identified correctly in the server section of the configuration. Send a test again after any modification to the SMTP gateway information. After successful receipt of an on the test account, be sure to replace the test address with the address stated in step 2.c. and click Test and then Apply. Sending another Test will immediately send the first AutoSend report to the QuickPage Clearing Office. If you are using the HP SMTP PROXY APPLICATION to act as your SMTP Server Gateway, the Test to an external account process will not work. Please just enter the meterinfo address and click Test and then Apply. 2

3 Section 2 Use the following steps to configure HP AutoSend on these two printers: HP Color LaserJet CM4540 MFP HP Color LaserJet CP5520 Series 1. Launch a browser (Internet Explorer 6.0 or greater) and connect to the device home page (for example, a) Navigate to General > Autosend and select Send to to configure the server. b) In the Outgoing Servers (SMTP) section, click Add. c) If the SMTP server is already known, choose the first option and click Next. If the SMTP server IP is not already known, choose the second option that looks for an SMTP server and click Next. 3

4 d) Provide the SMTP server and port (if asked). Use 25 for the port if no other is evident. If required, choose the option to split s based on size. NOTE On some models you will not see an input box for Port. e) Choose the required Server Authentication and click Next. If the SMTP server requires authentication, provide the username and password and click Next. 4

5 f) Click Finish. 2. After setting the SMTP server details: a) Navigate to General > AutoSend. b) Select Enable AutoSend and configure to send every 1 day (as shown below). c) Select Send to . d) Provide the destination address: meterinfo_xx@clearingoffice.com. Replace the XX (as shown here) with the 2-letter code for your country-specific address. To find the country-specific code, please refer to the table of addresses at the end of this document. e) Click Apply. IMPORTANT NOTE To ensure the SMTP server passes the to external destinations, please provide a test external address (such as a Yahoo, Gmail, Hotmail, or other web-based account other than the internal company account). Click on the Test button and check for the receipt of an message in the test address specified confirming the compatibility of the SMTP server. If an error message is shown at the AutoSend page or if the does not reach your test account, verify with your customer technical contact (IT) that the SMTP gateway is identified correctly in the Server section of the configuration. Send a test again after any modification to the SMTP gateway information. After successful receipt of an on the test account, be sure to replace the test address with the address stated in step 2.d. above and click Test and then Apply. ADDITIONAL NOTE If you are using the HP SMTP PROXY APPLICATION to act as your SMTP Server Gateway, the TEST to an external account process will not work. Please just enter the meterinfo address and click TEST and then APPLY. 5

6 Country Designation AutoSend meter address Australia AU Belgium BE Czech Republic CZ Denmark DK Finland FI France FR Germany DE Hong Kong HK Italy IT Luxembourg LU Mexico MX Netherlands NL Norway NO Portugal PT Republic of South Africa ZA Singapore SG Spain ES Sweden SE Switzerland CH United Kingdom UK 2010 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein _ENWW