Getting Started KX-TDA100 KX-TDA200. Hybrid IP-PBX. Model No.

Transcription

1 Getting Started Model No. Hybrid IP-PBX KX-TDA100 KX-TDA200 Thank you for purchasing a Panasonic Hybrid IP-PBX. Please read this manual carefully before using this product and save this manual for future use. KX-TDA100/KX-TDA200: PMPR Software File Version or later

2 Table of Contents Table of Contents 1 Before Installation Safety Notices System Connection Diagram Unpacking Installation Opening/Closing the Front Cover Inserting the SD Memory Card to the MPR Card Installing the Option Units Installing the Trunk Cards Installing the Extension Cards (DLC8/DLC16/DHLC8/MSLC16/SLC8/SLC16/ CSLC16) Connecting Extensions Frame Earth Connection Starting the PBX Starting the PBX Customising the PBX Connecting the PC Installing the Maintenance Console Programming the PBX Confirming the Connection Making Calls Getting Started

3 Section 1 Before Installation Getting Started 3

4 1.1 Safety Notices 1.1 Safety Notices Please observe the safety notices in this manual in order to avoid danger to users or other people, and prevent damage to property. The notices are classified as follows, according to the severity of injury or damage: WARNING This notice means that misuse could result in death or serious injury. CAUTION This notice means that misuse could result in injury or damage to property. 4 Getting Started

5 1.2 System Connection Diagram 1.2 System Connection Diagram LCOT4 (KX-TDA0183) DLC16 (KX-TDA0172) DLC8 (KX-TDA0171) for Digital Proprietary Telephone (DPT), DSS Console, and Portable Station (PS) KX-DT346/KX-DT343/ KX-T7636/KX-T7633 PC KX-DT300 KX-T7600 KX-DT300 KX-T7600 Telephone Company Private IP Network Batteries Station Message Detail Recording (SMDR) PC Analogue Trunk E & M Line ISDN BRI Line (Digital Trunk) ISDN PRI Line (Digital Trunk) T1 Line (Digital Trunk) E1 Line (Digital Trunk) Router LCOT16 (KX-TDA0181) LCOT8 (KX-TDA0180) CID/PAY8 (KX-TDA0189) CID8 (KX-TDA0193) DID8 (KX-TDA0182) E&M8 (KX-TDA0184) BRI4 (KX-TDA0284) BRI8 (KX-TDA0288) PRI30 (KX-TDA0290CE/ KX-TDA0290CJ) PRI23 (KX-TDA0290) T1 (KX-TDA0187) E1 (KX-TDA0188) IP-GW4 (KX-TDA0480) IP-GW4E (KX-TDA0484) IP-GW16 (KX-TDA0490) PSU-S/ PSU-M/ PSU-L (KX-TDA0108/ KX-TDA0104/ KX-TDA0103) MPR (Installed by default) MEC (KX-TDA0105) CSLC16 (KX-TDA0177) MSLC16 (KX-TDA0175) SLC16 (KX-TDA0174) SLC8 (KX-TDA0173) EXT-CID (KX-TDA0168) DHLC8 (KX-TDA0170) CSIF4 (KX-TDA0143) CSIF8 (KX-TDA0144) IP-EXT16 (KX-TDA0470) CTI-LINK (KX-TDA0410) OPB3 (KX-TDA0190) DPH4 (KX-TDA0161) DPH2 (KX-TDA0162) EIO4 (KX-TDA0164) ECHO16 (KX-TDA0166) MSG4 (KX-TDA0191) ESVM2 (KX-TDA0192) ESVM4 (KX-TDA0194) RMT (KX-TDA0196) Mountable Equipment PT-interface CS for Single Line Device for Single Line Device, DPT/Analogue Proprietary Telephone (APT), DSS Console, and PS Voice Processing System for PS for CTI communication via LAN connection USB DSS Console Radio CS PS for IP Proprietary Telephone (IP-PT) LAN Doorphone & Door Opener External Sensor/ External Relay Device CTI Server SLT APT Wireless Phone PS Amplifier DPT LAN PC Fax Machine DPT KX-DT346/ KX-DT343/ KX-T7636/ KX-T7633 PC Pager/Speaker DSS Console SLT CTI Server KX-DT300 KX-T7600 IP-PT Voice Processing System PS PT-interface CS IP Softphone KX-DT300 KX-T7600 Note In this manual, the suffix of each model number (e.g., KX-TDA100NE) is omitted unless necessary. Getting Started 5

6 1.3 Unpacking 1.3 Unpacking Check the package contents. Main Unit 1 CD-ROM (including manuals, etc.) 1 AC Cord *1 1 Screw A 3 (KX-TDA100) 4 (KX-TDA200) Screw B (Black) 2 (KX-TDA100) 6 (KX-TDA200) Anchor Plug 3 (KX-TDA100) 4 (KX-TDA200) Mini Plug (for pager and music source) 4 SD Memory Card 1 for KX-TDA100 Metal Bracket 1 for KX-TDA200 *1 The type of the AC cord may vary depending on the country/area of use. KX-TDA100BX/KX-TDA200BX is supplied with 2 types of AC cord. Please use whichever is appropriate for the country/area. In Canada, there is no ferrite core attached to the AC cord. 6 Getting Started

7 1.3 Unpacking Necessary tools (not supplied): ü Telephone cable for extension connection: Diameter of cable (ø 0.4 mm to ø 0.6 mm) ø 0.5 mm ø 0.5 mm ø 0.5 mm Maximum length of cable 1128 m for SLT 720 m for KX-DT300/KX-T7600 series 229 m for other DPT, APT and DSS Console The maximum length of the cable may vary depending on the type of cable and installation conditions. ü An RS-232C or USB cable for PC connection ü Connectors (Amphenol/RJ45/BNC) for trunk and extension connections Note Use a shielded twisted pair cable for the Amphenol connector. Use a twisted pair cable for the RJ45 connector. Getting Started 7

8 1.3 Unpacking 8 Getting Started

9 Section 2 Installation Getting Started 9

10 2.1 Opening/Closing the Front Cover 2.1 Opening/Closing the Front Cover Opening the Front Cover 1. Insert a flathead screwdriver into the opening (on the left of the screw cover) and unlatch the screw cover. Turn the screw anticlockwise to loosen. 2. Slide the front cover to the right until it stops, then lift the front cover. Closing the Front Cover 1. Hook the front cover onto the shelf (line up the protrusions on the cover with the receptacles on the shelf), then slide the front cover to the left until it locks. 10 Getting Started

11 SD CARD SD CARD SD CARD 2.2 Inserting the SD Memory Card to the MPR Card 2. Turn the screw clockwise to tighten, then secure the screw cover Inserting the SD Memory Card to the MPR Card The SD Memory Card contains software for all the processes of the PBX and all the customer data. The SD Memory Card must be inserted before startup. Example: KX-TDA200 1 MPR Card 2 SD Memory Card CAUTION Do not remove the SD Memory Card while power is supplied to the PBX. Doing so may cause the PBX to fail to start when you try to restart the system. Getting Started 11

12 2.3 Installing the Option Units 2.3 Installing the Option Units Slot Condition Install the power supply unit (PSU) into the left-most slot, and optional service cards into free slots. KX-TDA100 KX-TDA200 A B C D E A PSU Slot B Null Slot *1 C Free Slots 1 to 6 for Optional Service Cards D PSU Slot E Free Slots 1 to 11 for Optional Service Cards *1 Null slot is not available for any optional service card. CAUTION To protect the back board from static electricity, do not touch parts on the back board in the main unit, PSU, and on the optional service cards. To discharge static electricity, touch ground or wear an earthing strap. Make sure the screws are tightened to earth the card securely. Installing the Power Supply Unit 1. Insert the PSU along the guide rails. 2. Push the release lever in the direction of the arrow, so that the PSU engages securely with the connector on the back board. 12 Getting Started

13 2.3 Installing the Option Units 3. Turn the 4 screws clockwise, in the order indicated by the numbers 1 to 4, to fix the PSU. Back Board Release Lever 3 2 Screws 4 1 Guide Rail Installing the Trunk/Extension Cards 1. Insert the card along the guide rails. 2. Holding the card as shown below, push the release lever in the direction of the arrow so that the card engages securely with the connector on the back board. 3. Turn the 2 screws clockwise to fix the card in place. Back Board Release Lever Screws Guide Rail Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover. For details, refer to "Covering the Blank Slots" in "2.2.7 Installing/Removing the Optional Service Cards" of the Installation Manual. Getting Started 13

14 2.4 Installing the Trunk Cards 2.4 Installing the Trunk Cards LCOT4/LCOT8/LCOT16 Card Example: LCOT 16 Card Amphenol To trunk Accessories (included): Screws 2 User-supplied (not included): Amphenol connector 14 Getting Started

15 2.4 Installing the Trunk Cards BRI4/BRI8 Card Example: BRI8 Card To attach the ferrite core RJ45 When using 1 or 2 cables: TX2(-) RX1(-) RX2(+) TX1(+) LINE 1 to LINE 8 When using 3 or 4 cables: To NT1 Accessories (included): Ferrite core(s) 1 (BRI4 card) or 2 (BRI8 card) User-supplied (not included): RJ45 connector CAUTION For every 4 cables, use 1 ferrite core; a ferrite core holds a maximum of 4 cables. Attach the ferrite core as close to the card's connector as possible. Connect these optional service cards to the trunk through an NT1; do not connect to the U interface of the trunk directly. Notice When connecting the RJ45 connector, attach the included ferrite core. Note LINE 5 to LINE 8 are for BRI8 card only. These optional service cards have 100 W of terminal resistance. For use in point to multi-point connection, the cards must be placed at the end of the bus. Getting Started 15

16 2.4 Installing the Trunk Cards PRI30/PRI23 Card Example: PRI30 Card To attach the ferrite core RJ45 TX+ TX- RX- RX+ BNC (TX) TX+ 5 cm To NT1 To NT1 TX- BNC (RX) RX- RX+ For RJ45 120Ω 75Ω OR 120Ω 75Ω For BNC Accessories (included): Ferrite core 1 User-supplied (not included): RJ45 or BNC connectors CAUTION Connect these optional service cards to the trunk through an NT1; do not connect to the U interface of the trunk directly. Notice When connecting the RJ45 connector, attach the included ferrite core (except in Canada, where the ferrite core is not necessarily required). Note In some countries/areas, the PRI30 card must not be connected to the Public Switched Telephone Network. Use only 1 type of connector (RJ45 or BNC) for connection of PRI30 card; RJ45 and BNC cannot be used simultaneously. Set the termination switch to 120 W (default) or 75 W for connector type to be used. 16 Getting Started

17 2.6 Connecting Extensions 2.5 Installing the Extension Cards (DLC8/DLC16/ DHLC8/MSLC16/SLC8/SLC16/CSLC16) Example: DHLC8 Card To attach the ferrite core 3 cm Amphenol To extensions Accessories (included): Screws 2, Ferrite core 1 User-supplied (not included): Amphenol connector Note Attach the included ferrite core to the cable. 2.6 Connecting Extensions Example: KX-T7600 Series DPT Pin Assignments TO MAIN UNIT / PABX DPT and DSS Console H L APT H L To extension card RJ11 HTRL KX-T7000 Series SLT T R Getting Started 17

18 2.7 Frame Earth Connection 2.7 Frame Earth Connection 1. Loosen the screw. 2. Insert an earthing wire (user-supplied). 3. Tighten the screw. 4. Connect the earthing wire to earth. Screw Earthing wire To earth WARNING Connect the frame of the PBX to earth. Proper earthing (connection to earth) is very important to protect the PBX from the bad effects of external noise or to reduce the risk to the user of electrocution in the case of a lightning strike. CAUTION For earthing wire, green-and-yellow insulation is required, and the cross-sectional area of the conductor must be more than 0.75 mm 2 or 18 AWG. The earthing wire of the AC cable has an effect against external noise and lightning strikes, but it may not be enough to protect the PBX. A permanent connection between earth and the earth terminal of the PBX must be made. 18 Getting Started

19 Section 3 Starting the PBX Getting Started 19

20 3.1 Starting the PBX 3.1 Starting the PBX CAUTION Before touching the System Initialise Switch, discharge static electricity by touching ground or wearing an earthing strap. Once you have started the PBX and if you unplug the PBX, do not perform the following procedures to start the PBX again. Otherwise, your programmed data will be cleared. The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located near the equipment and is easily accessible. Use only the AC power cord included with the PBX for the PSU. Notice The SD Memory Card must be inserted in the SD Memory Card slot of the MPR card before startup. Note The PBX will continue to be powered even if the power switch is turned "OFF". 1. Slide the System Initialise Switch to the "SYSTEM INITIALIZE" position. RUN Indicator Power Supply Unit SYSTEM INITIALIZE To AC Outlet NORMAL System Initialise Switch 2. Plug the AC power cord into the PBX and an AC outlet, and turn on the PBX. The RUN indicator will flash. 3. While the RUN indicator is flashing, slide the System Initialise Switch back to the "NORMAL" position. Depending on the configuration, initialisation takes about 1 min to 3 min. If successfully executed, the RUN indicator will stop flashing and stay lit. All data will be cleared and the PBX will be initialised to the default values. The DPTs should show the time as 01: Getting Started

21 Section 4 Customising the PBX Getting Started 21

22 4.2 Installing the Maintenance Console 4.1 Connecting the PC The Maintenance Console serves as an overall system programming tool for the PBX. The Maintenance Console s Quick Setup lets you easily configure the PBX to receive intercom and trunk calls, as well as apply basic settings such as time and date. To programme the PBX, connect it to the PC with serial interface. Serial Interface Connection PC PC To USB Port To COM Port USB Port RS-232C Port RS-232C (Cross Cable) Pin Assignments COM Port Pin No RS-232C Port Pin No CAUTION When connecting a PC to the PBX via the RS-232C port, it is necessary to keep the following in mind to protect the system: 1. Make sure that both connector cases (frame ground) of the RS-232C cross cable (shielded cable)/usb cable are conductive. If they are not conductive, make sure that both connector cases of the cable are firmly connected. 2. If this is not possible, connect the frame of the PBX to the frame of the PC using an earthing wire in order to prevent difference in the electrical potentials. 4.2 Installing the Maintenance Console For the system requirements of the PC (e.g., operating system, hardware specifications), refer to "3.3.1 Installing and Starting the Maintenance Console" in the Installation Manual. Note Make sure to install and use the latest version of the Maintenance Console. To connect the PC to the PBX via USB, the KX-TDA USB driver must be installed. Follow the instructions of the wizard to install the KX-TDA USB driver. When the PBX is first connected to the PC via USB, you may be asked to select the appropriate USB driver. Browse for and select the KX-TDA USB driver that was installed previously. The contents and design of the software are subject to change without notice. Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation. 1. Copy the setup file of the Maintenance Console to your PC. 2. Double-click the setup file to run the installer. 3. Follow the on-screen instructions provided by the installation wizard. 22 Getting Started

23 4.3 Programming the PBX 4.3 Programming the PBX Starting the Maintenance Console and Assigning the Basic Items (Quick Setup) When you start the Maintenance Console with the Installer Level Programmer Code and connect to the PBX for the first time after initialisation (with the factory default setting), Quick Setup will launch automatically. During Quick Setup, you will set up the basic items. For details about the basic items, refer to "2.3.4 Quick Setup" in the Feature Guide. 1. Connect the PC to the PBX with a USB cable or RS-232C cross cable. 2. Start the Maintenance Console from the Start menu. 3. "Information before programming" appears. a. Carefully read this important additional information, which includes updates to this and other manuals. b. Click OK to close this window. 4. a. Enter the Installer Level Programmer Code (default: INSTALLER). b. Click OK. 5. Click Connect. 6. a. Select KX-TDA100/200 from PBX Model. b. Select the USB or RS-232C tab, depending on the serial interface connection with the PBX. c. Enter the system password for installer (default: 1234). d. Click Connect. 7. When country/area data do not match: a. Click OK to replace the country/area data of the PBX. Replacement may take several minutes to complete. b. Follow the procedure described in "Section 3 Starting the PBX" and restart the PBX. c. Repeat step 5 to reconnect the Maintenance Console. Getting Started 23

24 4.3 Programming the PBX 8. Follow the instructions of the Quick Setup wizard and assign the basic items (Quick Setup). The system menu appears. You may now begin programming the PBX. 24 Getting Started

25 4.3 Programming the PBX Assigning the BRI Setting (Automatic Configuration) 1. a. Under Configuration, click Slot. b. Move the mouse pointer over the BRI card. A menu will be shown under the mouse pointer. c. Click Ous to set the card to out-of-service status. 2. Click Tool BRI Automatic Configuration from the menu bar. 3. a. Click Check to turn on the BRI card. b. Click OK. 4. a. Enter the subscriber number for the desired ports in Subscriber. b. Click Execute. Note Network settings are automatically set. c. Click Check Box of the desired ports. d. Click Data Apply. e. Click Close. 5. a. Under Configuration, click Slot. b. Move the mouse pointer over the BRI card, then click INS to set the card to in-service status. Getting Started 25

26 4.3 Programming the PBX Assigning the Incoming Trunk Call Destination For analogue trunk users (DIL Setting): 1. Under CO & Incoming Call, click DIL Table & Port Settings. 2. Confirm that the DIL tab is selected. 3. Configure the settings as required. 4. Click OK. For ISDN trunk users (DDI Setting): 1. Under CO & Incoming Call, click DDI / DID Table. 2. Configure the settings as required. 3. Click OK. For ISDN trunk users (MSN Setting): 1. Under CO & Incoming Call, click DIL Table & Port Settings. 2. Click the DDI / DID / TIE / MSN tab. 3. Set the Distribution Method of the desired ports to MSN. 4. Click OK. 5. Click MSN Table. 6. Click the MSN tab. 7. Configure the settings as required. 8. Click OK. 26 Getting Started

27 4.3 Programming the PBX Setting an Extension Port to Use a DSS Console 1. Under Configuration, click Slot. 2. Move the mouse pointer over the desired extension card to display the menu of options. 3. Click Ous to set the card to out-of-service status. 4. Move the mouse pointer over the card again, then click Port Property. 5. For DPT Type, set the Type to DSS and assign the Location No.. 6. Click OK. 7. Under Extension, click DSS Console. 8. Select the desired pair extension number from Pair Extension. 9. Assign features to flexible buttons as required. 10. Click OK. 11. Under Configuration, click Slot. 12. Move the mouse pointer over the card to display the menu of options. 13. Click INS to set the card to in-service status. 14. Click Close. Getting Started 27

28 4.3 Programming the PBX 28 Getting Started

29 Section 5 Confirming the Connection Getting Started 29

30 5.1 Making Calls 5.1 Making Calls To call another extension extension no. Off-hook. Dial extension number. Talk. To call an outside party 9 / 0 outside phone no. Off-hook. Enter automatic line access number. Dial outside phone number. Talk. 30 Getting Started

31 The KX-TDA100E/KX-TDA200E, the KX-TDA100NE/KX-TDA200NE, the KX-TDA100GR/KX-TDA200GR, and the KX-TDA100CE/KX-TDA200CE are designed to interwork with the: Analogue Public Switched Telephone Network (PSTN) of European countries Pan-European Integrated Services Digital Network (ISDN) using ISDN basic rate access Pan-European Integrated Services Digital Network (ISDN) using ISDN primary rate access ONP 2048 kbit/s digital structured leased lines (D2048S) Panasonic Communications Co., Ltd./Panasonic Communications Company (U.K.) Ltd. declares that this equipment is in compliance with the essential requirements and other relevant provisions of Radio & Telecommunications Terminal Equipment (R&TTE) Directive 1999/5/EC. Declarations of Conformity for the relevant Panasonic products described in this manual are available for download by visiting: Contact to Authorised Representative: Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15, Hamburg, Germany

32 1-62, 4-chome, Minoshima, Hakata-ku, Fukuoka , Japan Copyright: This material is copyrighted by Panasonic Communications Co., Ltd., and may be reproduced for internal use only. All other reproduction, in whole or in part, is prohibited without the written consent of Panasonic Communications Co., Ltd. Panasonic Communications Co., Ltd PSQX2636TA KK0103AH7118