Brocade SilkWorm 4100 FC Switch Release Notes

Transcription

1 Brocade SilkWorm 4100 FC Switch Release Notes For Installation in Sun Storage Area Networks, 4.4.0b Firmware Sun Microsystems, Inc. Part No April 2005, Revision A Submit comments about this document at:

2 Copyright 2005 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved. Sun Microsystems, Inc. has intellectual property rights relating to technology that is described in this document. In particular, and without limitation, these intellectual property rights may include one or more of the U.S. patents listed at and one or more additional patents or pending patent applications in the U.S. and in other countries. This document and the product to which it pertains are distributed under licenses restricting their use, copying, distribution, and decompilation. No part of the product or of this document may be reproduced in any form by any means without prior written authorization of Sun and its licensors, if any. Third-party software, including font technology, is copyrighted and licensed from Sun suppliers. Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in the U.S. and in other countries, exclusively licensed through X/Open Company, Ltd. Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Sun StorEdge, Java, Sun Fire, Sun Blade, SunSolve, and Solaris are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and in other countries. All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. in the U.S. and in other countries. Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems, Inc. Mozilla is a trademark or registered trademark of Netscape Communications Corporation in the United States and other countries. The OPEN LOOK and Sun Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun s licensees who implement OPEN LOOK GUIs and otherwise comply with Sun s written license agreements. U.S. Government Rights Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and applicable provisions of the FAR and its supplements. DOCUMENTATION IS PROVIDED "AS IS" AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID. Copyright 2005 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, Californie 95054, Etats-Unis. Tous droits réservés. Sun Microsystems, Inc. a les droits de propriété intellectuels relatants à la technologie qui est décrit dans ce document. En particulier, et sans la limitation, ces droits de propriété intellectuels peuvent inclure un ou plus des brevets américains énumérés à et un ou les brevets plus supplémentaires ou les applications de brevet en attente dans les Etats-Unis et dans les autres pays. Ce produit ou document est protégé par un copyright et distribué avec des licences qui en restreignent l utilisation, la copie, la distribution, et la décompilation. Aucune partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque moyen que ce soit, sans l autorisation préalable et écrite de Sun et de ses bailleurs de licence, s il y en a. Le logiciel détenu par des tiers, et qui comprend la technologie relative aux polices de caractères, est protégé par un copyright et licencié par des fournisseurs de Sun. Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l Université de Californie. UNIX est une marque déposée aux Etats-Unis et dans d autres pays et licenciée exclusivement par X/Open Company, Ltd. Sun, Sun Microsystems, le logo Sun, AnswerBook2, docs.sun.com, Sun StorEdge, Java, Sun Fire, Sun Blade, SunSolve, et Solaris sont des marques de fabrique ou des marques déposées de Sun Microsystems, Inc. aux Etats-Unis et dans d autres pays. Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc. aux Etats-Unis et dans d autres pays. Les produits portant les marques SPARC sont basés sur une architecture développée par Sun Microsystems, Inc. Mozilla est une marque de Netscape Communications Corporation aux Etats-Unis et à d autres pays. L interface d utilisation graphique OPEN LOOK et Sun a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d utilisation visuelle ou graphique pour l industrie de l informatique. Sun détient une license non exclusive de Xerox sur l interface d utilisation graphique Xerox, cette licence couvrant également les licenciées de Sun qui mettent en place l interface d utilisation graphique OPEN LOOK et qui en outre se conforment aux licences écrites de Sun. LA DOCUMENTATION EST FOURNIE "EN L ÉTAT" ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y COMPRIS NOTAMMENT TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L APTITUDE A UNE UTILISATION PARTICULIERE OU A L ABSENCE DE CONTREFAÇON. Please Recycle

3 Brocade SilkWorm 4100 Switch Release Notes 4.4.0b Firmware This document contains important information about the Brocade SilkWorm 4100 FC switch for installation in Sun storage area networks (SANs). Read this document so that you are aware of issues or requirements that can impact the installation and operation of the Brocade SilkWorm 4100 switch. Note Sun is not responsible for the availability of third-party web sites mentioned in this document. Sun does not endorse and is not responsible or liable for any content, advertising, products, or other materials that are available on or through such sites or resources. Sun will not be responsible or liable for any actual or alleged damage or loss caused by or in connection with the use of or reliance on any such content, goods, or services that are available on or through such sites or resources. New Features in This Release on page 2 System Requirements on page 3 Known Issues and Bugs on page 9 Related Documentation on page 11 Service Contact Information on page 11 1

4 New Features in This Release The new Brocade Silkworm 4100 FC switch is fully interoperable with all other Brocade 1 Gb and 2 Gb switches. The additional features of this switch are: Flex port implementation. 4 Gb capability is limited to inter-switch links (ISLs) between Brocade SilkWorm 4100 FC switches. This new feature requires qualified 4 Gb Small Form-factor Pluggable (SFP) transceivers. Dual hot-swappable power supplies. For details of additional new features, refer to the Brocade Fabric OS v4.4.0b Release Notes. The following items are Brocade SilkWorm 4100 FC switch field-replaceable units (FRUs): Power supply Fan module 1/2 Gb SFP 1/2/4 Gb SFP (for ISL connections between Brocade Silkworm 4100 FC switches only) Brocade SilkWorm 4100 FC switch 2 Brocade SilkWorm 4100 FC Switch Release Notes April 2005

5 System Requirements This section covers the following topics: Software Requirements on page 3 Fabric Operating System (Switch Firmware) Requirements on page 4 Software Requirements This section lists the latest software requirements. Basic Software Requirements Solaris 8 Operating System (OS) 04/01 or later with the latest security patches Solaris 9 OS Solaris 10 SPARC or x86 OS Sun StorEdge SAN Foundation Software release or later Brocade Management Software Requirements There are several options available for managing a Brocade SilkWorm 4100 FC switch. This section provides a list of these options and any operating requirements required for these options: Java plug-in (or later) Command Line Interface Advanced WebTool v requires Mozilla 1.6 or later Fabric Manger v4.4 or later - Fabric Manager v4.4 has been qualified for S8 and S9. Please see the Fabric Manager v4.4 Release Notes for the latest details and OS requirements. Note Refer to the firmware release notes at the Brocade web site for information about the latest revisions to the above software at and click brocade connect on the top menu bar. A User ID and password are required. Otherwise contact your Sun service representative. Brocade SilkWorm 4100 Switch Release Notes 4.4.0b Firmware 3

6 Fabric Operating System (Switch Firmware) Requirements TABLE 1 summarizes the versions of Brocade fabric operating systems (FOS) that are supported in conjunction with this release. Sun recommends using the latest software release versions to optimize the benefits of a SAN. TABLE 1 Minimum Fabric Operating System (FOS) Requirements SilkWorm 2000 Series SilkWorm 3200 & 3800 Silkworm 3016, 3250, 3850, 3900, 12000, & * SilkWorm 4100 Brocade Fabric Manager General Compatibility With Secure FOS Enabled Recommended Software Versions v2.6.1 or later v3.1.0 or later v4.1.0 or later v4.4.0b or later v2.6.1 or later v3.1.2 or later v4.2.0 or later v4.4.0b or later v2.6.2 v3.2.0 v4.4.0 v4.4.0b or later 3.0.2c or later 3.0.2c or later 4.1. or later * SilkWorm 3016 is supported by Fabric OS v4.2.1x and v4.4.0b or later. SilkWorm 3250, 3850, and are supported by Fabric OS v4.2.0 or later. SilkWorm 3250, 3850, and are supported by Fabric Manager or later. SilkWorm 3900 is supported by Fabric OS v4.1.0 or later. SilkWorm 4100 is supported by Fabric Manager For Brocade FOS end-of-life information, see: 4 Brocade SilkWorm 4100 FC Switch Release Notes April 2005

7 Required Packages You need to install these packages, in the listed order, before you install the patches. If the packages are already on the system from a previous installation, you do not need to install them again. All of the packages can be found at: To access the packages on the Sun Downloads page, click the Storage Management link in the Systems Administration section. On the Storage Management page, click StorEdge SAN 4.4. SUNWsan SUNWcfpl SUNWcfplx SUNWfchba SUNWcfclr SUNWfchbr SUNWfchbx SUNWfcsm SUNWfcsmx SUNWcfcl SUNWcfclx SUNWmdiu SUNWjfca SUNWjfcax SUNWjfcau SUNWjfcaux For instructions on where and how to download the Sun StorEdge SAN Foundation software driver packages and patches required to run the switches with supported hardware from Sun, see the Sun StorEdge SAN Foundation Software Release Notes, Including StorEdge Traffic Manager for the Solaris Operating System, part number You can find this document at: hardware/docs/network_storage_solutions/san/index.html Brocade SilkWorm 4100 Switch Release Notes 4.4.0b Firmware 5

8 Required Patches TABLE 2 and TABLE 3 contain a list of the patches necessary to use the new Brocade FOS v4.4.0b. The latest patches are available at Note Install the Solaris OS update patches from either TABLE 2 or TABLE 3 in the order shown before installing the Brocade FOS v4.4.0b patch shown in TABLE 4. TABLE 2 Sun Solaris 8 OS Patches Patches xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx Name Sun StorEdge SAN Foundation software enhancements Sun StorEdge Traffic Manager software fcp/fp/fctl drivers fcip driver qlc driver luxadm and libq_fc/liba5k cfgadm fp plug-in library ses driver FCSM driver Common Fibre Channel HBA API library SNIA Sun Fibre Channel HBA library SBus Dual Fibre Channel Network Adapter Firmware * JNI driver support 1 Gb PCI Single/Dual FC Network Adapter FCode Single 2 Gb FC Network Host Adapter FCode Dual 2 Gb FC Network Host Adapter FCode JNI PCI Single + Dual 2 Gb FC Network Host Adapter FCode * Install the optional patch if the HBA FCode revision is or lower. See the patch README file for details. 6 Brocade SilkWorm 4100 FC Switch Release Notes April 2005

9 TABLE 3 Sun Solaris 9 OS Patches Patches xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx Name Sun StorEdge SAN Foundation software enhancements fcp patch luxadm and liba5k.so.2 patch Sun StorEdge Traffic Manager software fcp/fp/fctl drivers fcip driver qlc driver luxadm and libq_fc/liba5k cfgadm fp plug-in library FCSM driver Common Fibre Channel HBA API library SNIA Sun Fibre Channel HBA library SBus Dual Fibre Channel Network Adapter Firmware * JNI driver support 1 Gb PCI Single/Dual FC Network Adapter FCode Single 2 Gb FC Network Host Adapter FCode Dual 2 Gb FC Network Host Adapter FCode JNI PCI Single + Dual 2 Gb FC Network Host Adapter FCode * Install the optional patch if the HBA FCode revision is or lower. See the patch README file for details. TABLE 4 Patch Brocade Fabric Operating System v4.4.0b Patch Name Brocade switch v4.4.0b firmware patch Brocade SilkWorm 4100 Switch Release Notes 4.4.0b Firmware 7

10 To Download and Install the Patches The latest patches are available on the SunSolve SM web site with the use of PatchFinder. Use the following procedure to retrieve the patches for your Operating System and the patch for the 4.4.0b firmware. 1. Access the SunSolve web site at: 2. Under SunSolve Patch Contents, click Patch Portal. 3. Under PatchFinder, type the patch ID (refer to TABLE 2, TABLE 3, and TABLE 4) and click Find Patch. Do not type the -xx revision number. PatchFinder automatically finds the latest patch. 4. Verify that you have retreived the correct patch. 5. Print the page by doing one of the following: Print the page. Click Printer Friendly Page, and then print the page. Note Printing this page also prints the patch README file which contains the installation instructions, special instructions, special guidelines, and notes. 6. Download the patch by clicking on either HTTP or FTP in the following line: Download Patch (nn,nnn,nnn bytes) HTTP FTP. 7. Click PatchFinder and repeat the process from Step 3 for each patch. 8. When you are finished downloading all the patches, install the patches by following the instructions in each patch README file. 8 Brocade SilkWorm 4100 FC Switch Release Notes April 2005

11 Known Issues and Bugs This section details outstanding issues and bugs associated with running Brocade 4100 in a Sun StorEdge SAN Foundation Software environment. Switch Related Issues The following bugs are listed in order of increasing priority (P). Bug : During I/O and prolonged fault injection, multiple ports on a SilkWorm 3800 may fail to complete initialization and remain stuck in a G-port setting. As a result of the G-port setting, the host loses access to the storage unit on these ports. Workaround: Disable and re-enable the port, or disconnect the FC cable at the switch side and re-connect, or power cycle the storage device that has the G-port setting. Bug : Fabric boot of S10 from a x6768a HBA via Brocade 4100 may hang during boot. When this occurs, the host console output will indicate no I/O activity between the HBA and the boot device. Workaround: Issue the boot command again. It is not necessary to reset the host. Bug : Switches with firmware do not always recover after running a disable/enable test. Workaround: Enable the switch/director manually with CLI. Bug : Calling sectelnet from an expect script fails to login to switches with FOS v4.1.0/v Workaround: None at this time. Bug : Brocade switch details revision format via SNMP has too many trailing spaces. Workaround: Use CLI or WebTool to display the firmware revision. Brocade SilkWorm 4100 Switch Release Notes 4.4.0b Firmware 9

12 Driver and Utility Issues The following bugs are listed in order of increasing priority (P). Bug : While the SE6120 is busy processing I/O and a SE6120 CLI is used to change configuration, for example hwwn add..., this might force all LUNs associated with the active data path offline. Workaround: None at this time. Bug : Running the T3B/SE6120 lun perm command when the array is on redundant fabric might cause one of the data paths to failover. Workaround: None at this time. Array Firmware Issues The following bugs are listed in order of increasing priority (P). Bug : During the SE6120/SE6320 administration procedure (for example hwwn add... or hwwn rm... ), the host server may offline the data path to the SE6120/SE6320, especially when multiple hwwn add... are executed in quick succession. Workaround: Do not add lun or run hwwn commands in quick succession. Leave a gap (i.e. 10 to 20 seconds) in between commands to avoid a RSCN storm. Bug : The QLogic driver does not ignore LOGO with an invalid SID (0x0) and can result in a data path that is unusable. Workaround: Issue luxadm -e forcelip... to reset/reinitialize the link. Miscellaneous Issue Bug : A fabric boot with SG-XPCI2FC-JF2 ( ) or SG-XPCI1FC-JF2 ( ) fails when connected to a Brocade 4100 running FOS v4.4.0b. Workaround: Do not perform a fabric boot with the above HBAs via Brocade Only perform a fabric boot via a Brocade 4100 with other HBAs, or use the above HBAs connected to switches other then a Brocade Brocade SilkWorm 4100 FC Switch Release Notes April 2005

13 Related Documentation The Brocade Fabric OS v4.4.0b Release Notes are available with the Brocade Fabric Operating System v4.4.0b patch, xx. See To Download and Install the Patches on page 8. For instructions on where and how to download Sun StorEdge SAN Foundation software driver packages and patches, see Required Packages on page 5. Service Contact Information If you need help installing or using this product in the United States, call USA-4SUN, or go to: Brocade SilkWorm 4100 Switch Release Notes 4.4.0b Firmware 11

14 12 Brocade SilkWorm 4100 FC Switch Release Notes April 2005