455 D Control Board. FAAC International Inc. West Coast Operations 357 South Acacia Avenue Unit 357 Fullerton, CA Tel.

Transcription

1 455 D Control Board FAAC International Inc. Headquarter & East Coast Operations 55 Sunbeam Road Suites 9 Jacksonville, FL 57 Tel FAAC International Inc. West Coast Operations 57 South Acacia Avenue Unit 57 Fullerton, CA 98 Tel

2 CONTENTS. 455 D CONTROL BOARD. Warnings.. Technical Specifications. Electric Connections D Layout and Components.5 Programming 7.6 StartUp 9.7 System Test 0. OPERATING MODES DETAILED DESCRIPTION. PREWIRED ENCLOSURE DIAGRAM 4. POWER AND ACCESSORIES CONNECTIONS 4 AC Power Wiring Guidelines 4 AC Power Connection 4 Magnetic Lock Connection 4 LIMITED WARRANTY 5 Read this instruction manual before you begin installing product. = Information regarding personal safety and proper maintanence of product. = Information regarding product s characteristics or. Rev: 0 October 00

3 . 455 D CONTROL BOARD D Layout and Components. Warnings Important: Before attempting any work on control board (connections, maintenance, always turn off power. Power Supply 5 V~ ± 0% or 0 V~ 6% 0% 50/60 Hz Absorbed Power Motor Max. Load Accessories Max. Load Electric Lock Max. Load 0 W 800 W 0,5 A 5 VA Ambient Operating Temperature Range Protection Fuses (see Fig. A 4 F to F Function Logics: Semiautomatic / Automatic / Safety Devices / Stepped Semiautomatic / Stepped Automatic / Stepped Safety Devices / Semiautomatic B / Deadman C Opening/Closing Time Programmable (from 0 to 0 s Pause Time Please refer to Chapter 6 for AC power wiring guidelines.. Technical Specifications Closing Leaf Delay Opening Leaf Delay Thrust Force: Programmable (from 0 to 4 min. Programmable (from 0 to 4 min. s (can be excluded Adjustable on 50 levels for each motor Terminal Board Inputs: Open / Open Free Leaf / Stop / Limitswitch Opening Safety Devices / Closing Safety Devices / Power Supply Earth. Terminal Board Outputs: Flashing Lamp / Motors / 4 VDC Accessories Power Supply / 4 VDC IndicatorLight / Fail Safe / VAC Electric Lock Power Supply Programmable Functions: Logic / Pause Time / Thrust Force / Torque at Initial Thrust / Opening and Closing Leaf Delay / Reversing Stroke / OverPushing Stroke / IndicatorLight / PreFlashing / Electric Lock / Fail Safe / Safety Devices Logic / Assistance Request / Detection Time of Obstacle or Contact Point Learning Function: Simple or complete work time learning, with or without Limitswitch and/or Gatecoder. J J F PE N L MAIN F J COM OP M COM M OP CL LAMP J4 F J F OP_A STOP OP_B J CL OP A B CL OP TX STP 4V DL DL SIGNALLING AND PROGRAMMING DISPLAY J LOW VOLTAGE TERMINAL BLOCK J CONNECTOR FOR RP RECEIVER J AC POWER SUPPLY TERMINAL BLOCK FCA FCA F F FCC FCC J5 J5 J FCA FCC J6 FCA J Figure A J4 MOTORS AND FLASHING LAMP CONNECTION TERMINAL BLOCK J5 INDICATORLIGHT AND ELECTRIC LOCK TERMINAL BLOCK J6 LIMITSWITCH AND GATECODER TERMINAL BLOCK F MOTORS AND TRANSFORMER PRIMARY WINDING FUSE (F 5A 0V (F 0A 5V F LOW VOLTAGE AND ACCESSORIES FUSE (T 800mA F F PROGRAMMING PUSHBUTTON PROGRAMMING PUSHBUTTON PROGRAMMING PUSHBUTTON FCC. Electric Connections BLUE BLUE FCC VAC MAX. 60W 4 VDC W 0 VAC 50 Hz or 5 VAC 60 Hz A B STOP For connection of photocells and safety devices, see Section.4.. VAC LIMITSWITCH OR GATECODER NB: Capacitors are supplied with operator. Figure B

4 .4. Connection of Photocells and Safety Devices Before connecting photocells (or or devices, it is advisable to select type of according to movement area y have to protect (see Fig.C: Opening Safety Devices: They operate only during gate opening movement and, refore, are suitable for protecting area between opening leaves and fixed obstacles (walls, etc against risk of impact and crushing. Opening/Closing Safety Devices NOTE: All safety devices must be connected using NORMALLY CLOSED outputs. Closing Safety Devices: They operate only during gate closing movement and, refore, y are suitable for protecting closing area against risk of impact. Opening/Closing Safety Devices: They operate during gate opening and closing movements and, refore, y are suitable for opening and closing areas against risk of impact. FAAC recommends use of layout in Fig. D (in event of fixed obstacles at opening or in Fig. E (no fixed obstacles. N.B. If two or more devices have same function (opening or closing, y should be connected to each or in series (see Fig. L. Connection of ONE Pair of Closing Photocells and ONE Pair of Opening/Closing Photocells (Recommended Layout A B STP CL OP TX 4V 0 Figure C Closing Safety Devices A B STP CL OP TX 4V Opening Safety Devices Connection of ONE Pair of Closing Photocells, ONE Pair of Opening Photocells and ONE Pair of Opening/Closing Photocells (Recommended Layout 0 TX RX CL 4 5 TX OP/CL TX CL RX OP/CL 4 5 TX RX CL 4 5 TX CL TX Connection of ONE Closing Safety Device and ONE Opening Safety Device Figure E TX TX OP/CL RX OP/CL A B STP CL OP TX 4V 0 Figure F Connection of NO Safety Devices RX OP 4 5 TX OP TX A B STP CL OP TX 4V 0 Figure D Figure G 4

5 Connection of ONE Pair of Opening Photocells Connection of TWO Pairs of Closing Photocells A B STP CL OP TX 4V A B STP CL OP TX 4V 0 Figure H RX OP 4 5 TX OP TX RX CL 4 5 TX CL TX Connection of ONE Pair of Closing Photocells A B STP CL OP TX 4V 0 TX TX CL RX CL 4 5 Figure K RX CL 4 5 TX CL TX Connection of TWO N.C. Contacts in Series (e.g. Photocells, Stop Figure I Figure L Connection of ONE Pair of Opening Photocells and ONE Pair of Closing Photocells Connection of TWO N.O. Contacts in Parallel (e.g. Open A, Open B A B STP CL OP TX 4V 0 TX RX OP 4 5 TX CL TX OP RX CL 4 5 TX.4. Terminal Block J Power Supply (Fig. B PE: Earth Connection / Ground N: AC V~ power supply (Neutral L: AC V~ power supply (Line NB: For correct, board must be properly grounded. Figure M.4. Terminal Block J4 Motors and Flashing Lamp M: COM / OP / CL: Connection to Motor Can be used in single configuration M: COM / OP / CL: Connection to Motor Cannot be used in single configurations Figure J LAMP: Flashing lamp output ( AC V ~ 5

6 .4.4 Terminal Block J Accessories (Fig. B A Total Opening Command (N.O.: Any pulse generator (pushbutton, detector, etc. which, by closing a contact, commands opening and/or closing of both gate leaves. To install several full opening pulse generators, connect N.O. contacts in parallel. B Partial Opening Command (N.O. / Closing: Any pulse generator (pushbutton, detector, etc. which, by closing a contact, commands opening and/or closing of driven by motor M. In B and C logics, it always commands closing of both leaves. To install several partial opening pulse generators, connect N.O. contacts in parallel. STP STOP Contact (N.C.: Any device (e.g. a pushbutton which, by opening a contact, is able to stop gate movement. To install several STOP devices, connect N.C. contacts in series. NB: If STOP devices are not connected, jumper connect STP terminals and. CL Closing Safety Devices Contact (N.C.: The purpose of closing safety devices is to protect movement area during closing. During closing, in EASEPAPSP logics, safety devices reverse movement of gate leaves, or stop and reverse movement when y are released (see Advanced Programming in Section.5.. During closing cycle in logics B and C, y interrupt movement. They never operate during opening cycle. If closing safety devices operate when gate is open, y prevent closing movement..4.6 Connector J Rapid Connection to RP Receivers This is used for rapid connection to RP receivers (see Fig. Q. Connect accessory with components side facing inside of card. Insert and remove with power OFF. Figure Q 455 D RP 48 RP 4 RC NB: If no closing safety devices are connected, jumper connect terminals CL and TX (Fig. G. OP Opening safety devices contact (N.C.: The purpose of opening safety devices is to protect movement area during opening. During opening, in EASEPAPSP logics, safety devices reverse movement of gate leaves. During opening cycle in logics B and C, y interrupt movement. They never operate during closing cycle. If opening safety devices operate when gate is closed, y prevent opening movement. NB: If no opening safety devices are connected, jumper connect inputs OP and TX (Fig. G. Negative for power supply to accessories 4 VDC Positive for power supply to accessories Important: Accessories max. load is 500 ma. To calculate current draw, refer to instructions for individual accessories. TX Negative for power supply to photocell transmitters. If you use this terminal for connecting negative for supplying power to photocell transmitters, you may, if necessary, also use FAIL SAFE function (see Advanced Programming in Section.5.. If this function is enabled, equipment checks of photocells before each opening or closing cycle..4.5 Terminal Block J5 IndicatorLight and Electric Lock W.L. Power supply to indicatorlight Connect a 4 VDC W max. indicatorlight, if necessary, between this terminal and 4V supply. To avoid compromising correct of system, do not exceed indicated power. LOCK Power supply to electric lock If necessary, connect a VAC electric strike lock between this terminal and 4V power supply. Please refer to Chapter 6 for Magnetic Lock connection. 6

7 .4.7 Terminal Block J6 LimitSwitch or Gatecoder These inputs are designed for connection of opening and closing limitswitches or Gatecoders The 400 operator cannot use limit switches but only Gatecoders. They are used to detect s angular position and to thus obtain deceleration and stop positions more accurately than using operating timing. Please refer to Figure S for wiring information. If Gatecoders are not used J6 inputs can be left unconnected. Figure S RED BLACK RED BLACK.4.8 Operating Logics WHITE WHITE This is a brief description of main operating logics of system. For a complete description please refer to Table A (automatic: The gate opens on command and automatically closes after a pause phase. A second command while opening is ignored; a second command during pause phase interrupts pause time; a second command during closing reopens gate. A maintained open command will hold gate open. S (security: The security mode is like A logic except that a second command during opening immediately closes gate. A maintained open command will not hold gate open. E (semiautomatic: This mode requires a second command during opening stops gate. A second command during closing reopens gate. EP (semiautomatic, step by step: This mode requires a command to open and a command to close. A second command during opening or closing causes gate to stop. A third command n reverses previous motion of gate. B (manned, pulsed: This mode is designed for guard station use and requires a three button switch (pulsed to open, close, and stop gate. C (manned and constant: This mode requires constant pressure switches. One to open and one to close. No pressure on a switch stops gate. FCC.5 Programming To program 455D Control Board, you have to access PRO GRAMMING mode. Programming is split into two parts: BASIC and ADVANCED..5. Basic Programming To access BASIC PROGRAMMING, press key F: Press and hold F, unit will display name of first function / parameter. When you release key, unit will display parameter s current value. Value can be modified with keys and. Press and hold F again, unit will display name of next function / parameter. When you reach last function, press F to exit program, display resumes monitoring input status. The following table displays sequence of functions accessible in BASIC PROGRAMMING: BASIC PROGRAMMING PAUSE TIME: = Semiautomatic = Automatic = Safety Automatic = Stepped Semiautomatic = Stepped Automatic = Safety Stepped Automatic = B Semiautomatic = Deadman LEAF FORCE: Adjusts thrust of Motor. press Display Function Default OPERATING LOGICS (see tab. /a h: This has effect only when automatic logic is selected. Adjustable from to secs. in onesecond increments. Subsequently, display changes to minutes and tenths of seconds (separated by a decimal point, time is adjusted in 0second increments, up to minutes max. Thus, if unit displays Time is mins. and 50 secs. = minimum force = maximum force (hydraulic LEAF FORCE: Adjusts thrust of Motor. = minimum force = maximum force (hydraulic F, Pause LEAF CLOSING DELAY: Delays closing start of with respect to. Adjustable from to minutes (see Pause Time. TIME LEARNING (see Section F..: Enables selection between simple (automatic learning and complete (manual choice of deceleration and stop points learning. Simple Learning: Complete Learning: s. > s. Exit from programming and return to inputs status monitoring. If using hydraulic operators, set force to maximum level. 7

8 .5. Advanced Programming To access ADVANCED PROGRAMMING, press and hold key F and n press key : Release key, unit displays name of first function. Release key F, modify value of function with keys and. Press and hold key F, unit displays name of next function, and if you release it, value that can be modified with keys and. When you reach last function, press F to exit program, unit resumes monitoring input status. The following table shows sequence of functions accessible in ADVANCED PROGRAMMING: ADVANCED PROGRAMMING MAXIMUM TORQUE AT INITIAL THRUST: F Display Function Default The motors operate at maximum torque (ignoring torque setting at start of movement. Useful for heavy leaves. LAST STROKE AT CLOSING: The motors are activated at full speed for second to facilitate locking of electric lock. = Active =Disabled REVERSING STROKE: Before opening, while gate is closed, motors thrust to close for seconds thus facilitating release of electric lock. LEAF ING DELAY ( s: Enables delayed start (at opening of, avoiding interference between leaves. FAIL SAFE: If this function is activated, it enables a function test of photocells before any gate movement. If test fails (photocells not serviceable, gate does not start movement. PREFLASHING (5 s: Activates flashing lamp for 5 seconds before start of movement. ELECTRIC LOCK ON LEAF : For using electric lock on instead of on. NB: Parameter modifications take effect immediately. Exit out of programming to save changes. If equipment is powered down before returning to normal status monitoring, any unsaved modifications will be lost. To restore programming defaults, press and hold three buttons,, F simultaneously for 5 seconds. Display Function Default INDICATORLIGHT: If is selected, output functions as a standard indicatorlight (lighted at opening and pause, flashing at closing, and off when gate is closed. Different figures correspond to extra time compared to normal work time (opening or closing when output can be used via a relay to power a courtesy light. Time can be adjusted from to sec. in sec. steps, and from to min. in 0 sec. steps. = Standard indicatorlight from to = Timed output CLOSING PHOTOCELLS REVERSE AT RELEASE: Enable this function if you want closing photocells to stop movement and reverse at release. Default setting is immediate reverse. A.D.M.A.P. FUNCTION: When enabled, safety devices operate in compliance with French standard NFP 5/6. ASSISTANCE REQUEST (combined with next function: If activated, at end of countdown (settable with next function i.e. Cycle programming it affects 8 s of preflashing at every Open pulse (job request. Can be useful for setting scheduled maintenance jobs. CYCLE PROGRAMMING: For setting countdown of system cycles. Settable (in thousands from to thousand cycles. The displayed value is updated as cycles proceed. This function can be used to check use of board or to exploit Assistance request. ANTICRUSHING SENSITIVITY: When operating with gatecoder, it controls anticrushing sensitivity. = Low = High. EXTRA WORK TIME: When operating without a gatecoder and limitswitch, if reversing occurs, and if does not reach its end contact point, you can activate this function to increase work time. Exit from programming and return to inputs status monitoring. 8

9 .6 StartUp.6. LED Check The board has a twodigit display. When not in PROGRAMMING mode, this display is used to indicate status of inputs. Fig. U shows how LED segments of display exactly correspond to inputs. Figure U The table below shows status of LEDs in relation to status of inputs. Note following: LED ON = closed contact LED OFF = open contact Operation of Status Signaling LEDs LEDs ON OFF OP_A Command activated Command inactive OP_B Command activated Command inactive STOP Command inactive Command activated CL Safety devices clear Safety devices triggered OP Safety devices clear Safety devices triggered FCA (if used FCC (if used FCC (if used FCA (if used The status of LEDs while gate is closed at rest are shown in bold.. Program functions of 455 D control board according to need, as previously shown.. Cut power to electronic control equipment.. Release operators and manually move gate to midpoint of opening angle. 4. Relock operators. 5. Restore power. Flashes when Gatecoder is in use Flashes when Gatecoder is in use Flashes when Gatecoder is in use Flashes when Gatecoder is in use.6. Rotation Direction and Force Check 6. Send and opening command on A input (Fig.B and check if gate leaves are being commanded to open. N.B: If first A pulse commands a closing, cut power and reverse phases of electric motor (red and black wires on 455 D control board. 7. Check force setting of motors, modify if necessary (see Section.5.. N.B: For hydraulic operators, like 400, force should be programmed to maximum level (50 8. Stop movement with a STOP command. 9. Release operators, close leaves and relock operators. Make sure travel limit mechanical stops are present. WARNING: During learning procedure, safety devices are disabled! Avoid crossing movement area when this is carried out..6. Learning Operating Times Opening/closing time is established by a learning procedure which varies slightly according to wher you are using Gatecoders or not..6.. LEARNING NORMAL TIMES Normal learning (i.e. without limitswitches and Gatecoders can be accomplished in two ways: SIMPLE LEARNING (Without Slow Down: Check that leaves are closed. Enter BASIC PROGRAMMING, select TIME LEARNING function and n press pushbutton for second. The display begins flashing and leaves begin to open. As soon as leaves reach opening contact point, provide an A pulse (with key operated pushbutton or with radio control to stop movement. The leaves stop and display stops flashing. Press pushbutton F to exit and save programming. The procedure is complete and gate is ready to operate. COMPLETE LEARNING (With Slow Down: Check that leaves are closed. Enter BASIC PROGRAMMING, select TIME LEARNING function and n press pushbutton for more than seconds. The display begins flashing and begins to open. The following functions can be performed by sending A pulses (by key pushbutton or radio control: Slow down at opening of Leaf stops at opening and begins its opening movement Slow down at opening of 4 Leaf stops at opening and immediately begins its closing movement 5 Slow down at closing of 6 Leaf stops at closing and begins its closing movement 7 Slow down at closing of 8 Leaf stops at closing When display stops flashing, press pushbutton F to exit and save programming. The procedure is complete and gate is ready to operate. Notes: If you wish to eliminate deceleration in certain stages, wait for to reach its stoplimit and supply consecutive Open pulses (by second. If only one is present, entire sequence must neverless be effected. When has finished opening, supply 5 Open pulses until begins to close, and n resume normal..6.4 Learning Times with Gatecoder Learning with Gatecoder can be accomplished in two ways: SIMPLE LEARNING (With Slow Down: Check that leaves are closed. Access BASIC PROGRAM MING, select TIME LEARNING function and n press pushbutton for second: display begins flashing and leaves begin opening movement. The movement stops automatically when opening stop limit is reached. The display will stop flashing. Press pushbutton F to exit and save programming. The procedure is complete and gate is ready to operate, using default slow down set at factory. COMPLETE LEARNING (With Slow Down: Check that leaves are closed. Access BASIC PROGRAM MING, select TIME LEARNING function and n press pushbutton for more than seconds. The display begins flashing and begins to open. The following functions can be performed by sending A pulses (by radio control or key pushbutton: 9

10 Leaf slows down at opening (it stops automatically on reaching stop limit Leaf opening movement begins Leaf slows down at opening (it stops automatically on reaching stop limit 4 Leaf closing movement begins 5 Leaf slows down at closing (it stops automatically on reaching stop limit 6 Leaf closing movement begins 7 Leaf slows down at closing (it stops automatically on reaching stop limit 8 End of learning When display stops flashing, press pushbutton F to exit and save programming. The procedure is complete and gate is ready to operate. Notes: The slow down pulse should be given before gate reaches positive stop to prevent from hitting it at full speed (it would be mistaken for an obstacle. If only one is present, entire sequence must neverless be effected. When has finished opening, supply 5 Open pulses until begins to close, and n resume normal..7 System Test When you are finished programming, test system. Verify that entire system operates correctly. Most importantly, check that force is adequately adjusted and that safety devices are operating correctly. 0

11 . OPERATING MODES DETAILED DESCRIPTION Tab. /a L ogic "E" PULSE S G ATE STATUS O PEN A O PEN B S TO P O PEN IN G SA FETY DEVIC E S C LO SIN G SA FETY DEVIC E S O P/C L SA FETY DEVIC E C LO SED f O pens lea O pens single lea f O PEN Recloses im m ediately ( (if on part.opng. O PEN A disabled ( C LO SIN G y Reopens im m ediatel N o (saves effect O PEN see paragraph 5.. Locks and, on release, open reverses to O PEN IN G S tops ( R everses to clos e N o effec t Locks and, on release, continues opening LO C KED C loses (w ith C losing Safety devices engaged, opens at nd pulse ( Tab. /b L ogic "A " PULSE S G ATE STATUS O PEN A O PEN B S TO P O PEN IN G SA FETY DEVIC E S C LO SIN G SA FETY DEVIC E S O P/C L SA FETY DEVIC E C LO SED O pens and closes it after pause tim e ( O pens single and closes after pause tim e ( O PEN on PA USE Reloads pause tim e (( Reloads pause tim e ( ( (if on part.opng. O PEN A disabled Reloads pause tim e ( C LO SIN G Reopens im m ediately ( N o (saves effect O PEN see paragraph 5.. Locks and, on release, open reverses to O PEN IN G L O C KED ( ( R everses to clos e N o effec t C loses ( Locks and, on release, continues opening Tab. /c L ogic "S" PULSE S G ATE STATUS O PEN A O PEN B S TO P O PEN IN G SA FETY DEVIC E S C LO SIN G SA FETY DEVIC E S O P/C L SA FETY DEVIC E C LO SED O pens and closes O pens it after pause tim e single and closes after pause tim e O PEN on PA USE Recloses im m ediately ( O n (if on part.opng. O PEN A disabled release, closes after 5" (O PEN O n disabled ( release, closes after 5" C LO SIN G y Reopens im m ediatel N o (saves effect O PEN see paragraph 5.. Locks and, on release, open reverses to O PEN IN G R ecloses im m ediately ( Reverses to clos e Locks and, (saves O PEN on release, continues opening L O C KED C loses ( O PEN disabled Tab. /d Logic "EP" PULSES GATE STATUS A B STOP ING SAFETY DEVICES CLOSING SAFETY DEVICES OP/CL SAFETY DEVICE CLOSED Opens Opens for partial opening time No effect No effect No effect ( disabled ( disabled Recloses immediately ( No effect (if on part.opng. A No effect ( disabled ( No effect ( disabled disabled CLOSING No effect (saves see paragraph 5.. Locks and, on release, reverses to open ING ( see paragraph 5.. No effect Locks and, on release, continues opening LOCKED Restarts movement in reverse direction ( (always closes after a Stop No effect ( disabled No effect (if it must open, it disables No effect No effect ( disabled (if it must close, it disables ( If maintained, it prolongs pause until disabled by command (timer function ( If anew pulse occurs within seconds after reversing, it immediately stops. ( During partial opening cycle, an Apulse causes total opening. NB.: Effects on or active pulse inputs in brackets.

12 Tab. /e L ogic "A P" PULSE S G ATE STATUS O PEN A O PEN B S TO P O PEN IN G SA FETY DEVIC E S C LO SIN G SA FETY DEVIC E S O P/C L SA FETY DEVIC E C LO SED O pens and closes O pens it after pause tim e single and closes after pause tim e O PEN on PA USE ( (if on part.opng. O PEN A disabled Reloads pause tim e ( Reloads pause tim e C LO SIN G y Reopens im m ediatel N o (saves effect O PEN see paragraph 5.. Locks and, on release, open reverses to O PEN IN G S tops ( R everses to clos e N o effec t Locks and, on release, continues opening LO C KED C loses (w ith C losing Safety devices engaged, opens at nd pulse ( Tab. /f L ogic "SP" PULSE S G ATE STATUS O PEN A O PEN B S TO P O PEN IN G SA FETY DEVIC E S C LO SIN G SA FETY DEVIC E S O P/C L SA FETY DEVIC E C LO SED O pens and closes O pens it after pause tim e single and closes after pause tim e O PEN on PA USE ( O n (if on part.opng. O PEN A disabled release, closes after 5" (O PEN O n disabled ( release, closes after 5" C LO SIN G y Reopens im m ediatel N o (saves effect O PEN see paragraph 5.. Locks and, on release, open reverses to O PEN IN G S tops ( Reverses to clos e Locks and, (saves O PEN on release, continues opening L O C KED C loses ( O PEN disabled Tab. /g L ogic "B" PULSE S G ATE STATUS O PEN A (opening O PEN B (closing S TO P O PEN IN G SA FETY DEVIC E S C LO SIN G SA FETY DEVIC E S O P/C L SA FETY DEVIC E C LO SED f O pens lea N o effec t (O PEN A disabled (O PEN A disabled O PEN t N o effec C loses lea f (O PEN B disabled (O PEN B disabled (O PEN B disabled C LO SIN G n O PEN IN G t R everses to ope N o effec t N o effec N o effec t N o (saves (O PEN A effect O PEN A disabled ( O PEN B disabled operatio n (O PEN A /B disabled L O C KED f O pens lea C loses lea f ( A/B disabled (O PEN A disabled (O PEN B disabled (O PEN A /B disabled Tab. /h L ogic "C " C O N TRO LS A LWAYS HELD DO W N PULSE S G ATE STATUS O PEN A (opening O PEN B (closing S TO P O PEN IN G SA FETY DEVIC E S C LO SIN G SA FETY DEVIC E S O P/C L SA FETY DEVIC E C LO SED f O pens lea (O PEN A disabled (O PEN A disabled (O PEN A disabled O PEN C loses (O PEN B disabled (A/B disabled (O PEN A disabled (O PEN B disabled (O PEN B disabled C LO SIN G n S tops operatio / O PEN IN G / n operatio (O PEN A disabled ( O PEN B disabled operatio n (O PEN A /B disabled ( If maintained, it prolongs pause until disabled by command (timer function ( If anew pulse occurs within seconds after reversing, it immediately stops. ( During partial opening cycle, an Apulse causes total opening. NB.: Effects on or active pulse inputs in brackets.

13 . PREWIRED ENCLOSURE DIAGRAM 455 D Contr ol Boa r d

14 4. POWER AND ACCESSORIES CONNECTIONS AC Power Wiring Guidelines. Check local wiring codes in all cases and follow all local building codes. Wiring and hookup should be performed by qualified electricians/installers only.. AC power should be supplied from a circuit breaker panel and must have its own dedicated circuit breaker. This supply must include a green ground conductor.. Properly ground gate operator to minimize or prevent damage from power surges and/or lightning. Use a grounding rod if necessary. A surge suppressor is recommended for additional protection. Magnetic Lock Connection When connecting a magnetic lock to system, use Maglock Relay Kit (P/N: 5 and connect it as follows: AC Power Connection. Turn circuit breaker for AC gate operator power to OFF before connecting AC input wires.. Turn Power Switch located on left side of prewired enclosure to OFF before connecting AC input wires.. Connect AC input wires to AC terminal located on top left of enclosure. See diagram on right. 4

15 LIMITED WARRANTY To original purchaser only: FAAC International, Inc., warrants, for twentyfour (4 months from date of invoice, gate operator systems and or related systems and equipment manufactured by FAAC S.p.A. and distributed by FAAC International, Inc., to be free from defects in material and workmanship under normal use and service for which it was intended provided it has been properly installed and operated. FAAC International, Inc. s obligations under this warranty shall be limited to repair or exchange of any part of parts manufactured by FAAC S.p.A. and distributed by FAAC International, Inc. Defective products must be returned to FAAC International, Inc., freight prepaid by purchaser, within warranty period. Items returned will be repaired or replaced, at FAAC International, Inc. s option, upon an examination of product by FAAC International, Inc., which discloses, to satisfaction of FAAC International, Inc., that item is defective. FAAC International, Inc. will return warranted item freight prepaid. The products manufactured by FAAC S.p.A. and distributed by FAAC International, Inc., are not warranted to meet specific requirements, if any, of safety codes of any particular state, municipality, or or jurisdiction, and neir FAAC S.p.A. or FAAC International, Inc., assume any risk or liability whatsoever resulting from use reof, wher used singly or in combination with or machines or apparatus. Any products and parts not manufactured by FAAC S.p.A. and distributed by FAAC International, Inc., will carry only warranty, if any, of manufacturer. This warranty shall not apply to any products or parts reof which have been repaired or altered, without FAAC International, Inc. s written consent, outside of FAAC International, Inc. s workshop, or altered in any way so as, in judgment of FAAC International, Inc., to affect adversely stability or reliability of product(s or has been subject to misuse, negligence, or accident, or has not been operated in accordance with FAAC International, Inc. s or FAAC S.p.A. s instructions or has been operated under conditions more severe than, or orwise exceeding, those set forth in specifications for such product(s. Neir FAAC S.p.A. nor FAAC International, Inc., shall be liable for any loss or damage whatsoever resulting, directly or indirectly, from use or loss of use of product(s. Without limiting foregoing, this exclusion from liability embraces a purchaser s expenses for downtime or for making up downtime, damages for which purchaser may be liable to or persons, damages to property, and injury to or death of any persons. FAAC S.p.A. or FAAC International, Inc., neir assumes nor authorizes any person to assume for m any or liability in connection with sale or use of products of FAAC S.p.A. or FAAC International, Inc. The warranty herein above set forth shall not be deemed to cover maintenance parts, including, but not limited to, hydraulic oil, filters, or like. No agreement to replace or repair shall constitute an admission by FAAC S.p.A. or FAAC International, Inc., of any legal responsibility to effect such replacement, to make such repair, or orwise. This limited warranty extends only to wholesale customers who buy directly through FAAC International, Inc. s normal distribution channels. FAAC International, Inc., does not warrant its products to end consumers. Consumers must inquire from ir selling dealer as to nature and extent of that dealer s warranty, if any. This warranty is expressly in lieu of all or warranties expressed or implied including warranties of merchantability and fitness for use. This warranty shall not apply to products or any part reof which have been subject to accident, negligence, alteration, abuse, or misuse or if damage was due to improper installation or use of improper power source, or if damage was caused by fire, flood, lightning, electrical power surge, explosion, wind storm, hail, aircraft or vehicles, vandalism, riot or civil commotion, or acts of God. 5