LED Driver Linear / area fixed output

Transcription

1 Driver LC W /3/3/7/mA fixc lp SNC ESSENCE series Product description Fixed output built-in LED Driver Constant current LED Driver Output current, 3, 3, 7 or 1, ma Max. output power W For luminaires of protection class I and protection class II Temperature protection as per EN Ce Nominal life-time up to, h -year guarantee Properties Casing: metal, white Type of protection IP2 Functions Overload protection Short-circuit protection No-load protection Burst protection voltage 1 kv Surge protection voltage 1 kv (L to N) Surge protection voltage 2 kv (L/N to earth) È Standards, page 3 Wiring diagrams and installation examples, page 4 Data sheet 1/16-LC

2 Driver LC W /3/7/mA fixc lp SNC ESSENCE series Technical data Rated supply voltage V AC voltage range V Mains frequency / 6 Hz Output power range 3 W THD (at 23 V, Hz, full load) < 2 % Output current tolerance 3 ± 7. % Typ. current ripple (at 23 V, Hz, full load) ± 3 % Turn on time (at 23 V, Hz, full load). s Turn off time (at 23 V, Hz, full load). s Hold on time at power failure (output) s Ambient temperature ta C Ambient temperature ta (at life-time, h) 4 C Storage temperature ts C Dimensions L x W x H 23 x 3 x 21 mm Hole spacing D 218 mm Ø4,1 Ordering data Type side fixing feature 23 Article number 218 Packaging, carton Packaging, low volume 4,1 2,7 3 Packaging, high volume Weight per pc. LC W ma fixc lp SNC pc(s). 1, pc(s). 3, pc(s)..144 kg LC W 3mA fixc lp SNC pc(s). 1, pc(s). 3, pc(s)..142 kg LC W 3mA fixc lp SNC 8744 pc(s). 1, pc(s). 3, pc(s)..142 kg LC W 7mA fixc lp SNC pc(s). 1, pc(s). 3, pc(s)..14 kg LC W ma fixc lp SNC pc(s). 1, pc(s). 3, pc(s)..143 kg Specific technical data Type Output Input current Max. Typ. power Power Efficiency Efficiency Min. Max. Max. Max. peak output Max. peak Max. casing current 3 (at 23 V, Hz, full load input power consumption (at 23 V, factor at full load 1 at full load 1 at min. load 1 at min. load 1 forward voltage 1 forward voltage 1 output voltage current at full load 12 output current at min. temperature tc Hz, full load) load 12 LC W ma fixc lp SNC ma.242 A W 4. W. 92 %.9C 91. % 12. V 2. V 4 V 3 ma 32 ma 7 C LC W 3mA fixc lp SNC 3 ma.242 A W 4. W. 92 %.9C 91. % 1. V 167. V 4 V 36 ma 38 ma 7 C LC W 3mA fixc lp SNC 3 ma.242 A W 4. W. 92 %.9C 91. % 86. V 143. V 3 V 43 ma 46 ma 7 C LC W 7mA fixc lp SNC 7 ma.242 A W 4. W. 91 %.9C 9. % 43. V 71. V 3 V 9 ma 94 ma 7 C LC W ma fixc lp SNC 1, ma.3 A 6 W. W. 89 %.9C 88. % 28. V 47. V 3 V 1,32 ma 1,46 ma 8 C 1 Test result at 23 V, Hz. 2 The trend between min. and full load is linear. 3 Output current is mean value. Data sheet 1/16-LC

3 Standards EN EN EN EN EN EN 647 Overload protection If the output voltage range is exceeded the LED Driver will protect itself and LED may flicker. After elimination of the overload, the nominal operation is restored automatically. Short-circuit behaviour In case of a short circuit on the output side (LED) the LED Driver switches into hic-cup mode. After elimination of the short-circuit fault the LED Driver will recover automatically. No-load operation The LED Driver works in burst working mode to provide a constant output voltage regulation which allows the application to be able to work safely when LED string opens due to a failure. Mounting of device Max. torque for fixing:. Nm/M4 Storage conditions Humidity: % up to max. %, not condensed (max. 6 days/year at %) Storage temperature: -4 C up to max. +8 C The devices have to be within the specified temperature range (ta) before they can be operated. Installation instructions The LED module and all contact points within the wiring must be sufficiently insulated against 4 kv surge voltage. Air and creepage distance must be maintained. Replace LED module 1. Mains off 2. Remove LED module 3. Wait for 3 seconds 4. Connect LED module again Hot plug-in or output switching of LEDs is not permitted and may cause a very high current to the LEDs. Expected life-time Type ta 4 C C 6 C LC W ma fixc lp SNC tc 6 C 7 C x Life-time, h, h x LC W 3mA fixc lp SNC tc 6 C 7 C x Life-time, h, h x LC W 3mA fixc lp SNC tc 6 C 7 C x Life-time, h, h x LC W 7mA fixc lp SNC tc 6 C 7 C x Life-time, h, h x LC W ma fixc lp SNC tc 7 C 8 C x Life-time, h, h x The LED Driver is designed for a life-time stated above under reference conditions and with a failure probability of less than 1 %. Maximum loading of automatic circuit breakers Automatic circuit breaker type C1 C13 C16 C2 B1 B13 B16 B2 Inrush current Installation Ø 1. mm 2 1. mm 2 1. mm 2 2. mm 2 1. mm 2 1. mm 2 1. mm 2 2. mm 2 Imax Time LC W ma fixc lp SNC A 37 µs LC W 3mA fixc lp SNC A 37 µs LC W 3mA fixc lp SNC A 37 µs LC W 7mA fixc lp SNC A 37 µs LC W ma fixc lp SNC A 37 µs Harmonic distortion in the mains supply (at 23 V / Hz and full load) in % THD LCI W ma fixc lp SNC < 2 < 9 < 2 < 2 < 2 < 2 LCI W 3mA fixc lp SNC < 2 < 1 < 2 < 1 < 1 < 1 LCI W 3mA fixc lp SNC < 2 < 1 < 2 < 2 < 1 < 1 LCI W 7mA fixc lp SNC < 2 < < 4 < 1 < 1 < 1 LCI W ma fixc lp SNC < 2 < < 4 < 2 < 2 < 2 Data sheet 1/16-LC

4 Wiring diagram V /6 Hz L N Wiring type and cross section The wiring can be stranded wires with ferrules or rigid wires with a cross section of. 1. mm². Strip mm of insulation from the cables to ensure perfect operation of the push-wire terminals (WAGO ). wire preparation:. 1. mm² PRI SEC + LED LED mm Isolation and electric strength testing of luminaires Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production. According to IEC Annex Q (informative only!) or ENEC 33-Annex A, each luminaire should be submitted to an isolation test with V DC for 1 second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal. The isolation resistance must be at least 2 MΩ. As an alternative, IEC Annex Q describes a test of the electrical strength with V AC (or x V DC). To avoid damage to the electronic devices this test must not be conducted. Additional information Additional technical information at Technical Data Guarantee conditions at Services Life-time declarations are informative and represent no warranty claim. No warranty if device was opened. Wiring guidelines All connections must be kept as short as possible to ensure good EMI behaviour. Mains leads should be kept apart from LED Driver and other leads (ideally 1 cm distance) Max. lenght of output wires is 2 m. Incorrect wiring can damage LED modules. The wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.). Earth connection The earth connection is conducted as protection earth (PE). The LED Driver can be earthed via metal housing. If the LED Driver will be earthed, protection earth (PE) has to be used. There is no earth connection required for the functionality of the LED Driver. Earth connection is recommended to improve following behaviour. Electromagnetic interferences (EMI) Transmission of mains transients to the LED output In general it is recommended to earth the LED Driver if the LED module is mounted on earthed luminaire parts respectively heat sinks and thereby representing a high capacity against earth. For Class I application, protection earth need to connected with the metal housing (bottom part). For Class II application, protection earth is no need to be connected, below 2 scenarios should be considered: If the LED Driver housing is screwed on a metal part inside the luminaires, both LED Driver and LED module must be isolated. If the LED Driver housing is screwed on a plastic part inside the luminaires, the LED module need to be isolated. Release of the wiring Press down the push button and remove the cable from front. Data sheet 1/16-LC

5 Diagrams LC W ma fixc lp SNC ,,98,96,94,92,9,88,86,84,82,8 6 Input power vs load Data sheet 1/16-LC

6 Diagrams LC W 3mA fixc lp SNC ,,98,96,94,92,9,88,86,84,82,8 6 Input power vs load Data sheet 1/16-LC

7 Diagrams LC W 3mA fixc lp SNC ,,98,96,94,92,9,88,86,84,82,8 6 Input power vs load Data sheet 1/16-LC

8 Diagrams LC W 7mA fixc lp SNC ,,98,96,94,92,9,88,86,84,82,8 6 Input power vs load Data sheet 1/16-LC

9 Diagrams LC W ma fixc lp SNC ,,98,96,94,92,9,88,86,84,82, Data sheet 1/16-LC