Thick Film Chip Resistors
|
|
- Sheryl Dorsey
- 7 years ago
- Views:
Transcription
1 0201 Chip Resistors * size and above, see Pages C5-C9 Features: Reduced size of final equipment ower assembly costs Higher component and equipment reliability pplications: Camcorders Cellular Hearing aids dvanced pagers Palmtop computers hick Film Chip Resistors Resistance range Resistance tolerance Description emperature coefficient R Ω Ω<R 1MΩ bsolute maximum dissipation at amb=70 C Maximum permissible voltage Climatic category (IEC 6006) asic specification 10Ω to 1 MΩ; E24 Series % x 10-6 /K 50 x 10-6 /K 1/20 15V (DC or RMS) 55/5/56 IEC Description: he resistors are constructed on a high grade ceramic body (aluminum oxide). Internal metal electrodes are added at each end and connected by a resistive paste which is applied to the top surface of the substrate. he composition of the paste is adjusted to give the approximate resistance required and the value is trimmed to within tolerance, by laser cutting of this resistive layer. he resistive layer is covered with a protective coating. Finally, external end terminations are added. For ease of soldering the outer layer of these end terminations is a lead-in alloy. Derating: he power that the resistor can dissipate depends on the operating temperature. See Fig. 1. CR02 imiting Voltage (1) (V) 15 Pmax (% Prated) 50 imiting Power () amb ( C) Fig. 1Maximum dissipation (Pmax) in percentage of rated power as a function of the ambient temperature (amb). Note: his is the maximum voltage that may be continuously applied to the resistor element. IS EECRONICS, INC : 3506D ake Center Dr, Santa na, C Coldwater Canyon, el: North Hollywood. California Fax: Phone (1) oll Free (00) Fax (1) C3
2 hick Film Chip Resistors Size Chip Resistors 2 For Series (%-J, %-G, 0%-K olerances) 3 DIGI SYSEM - First two digits are significant and third digit is multiplier, R indicates decimal on values under 10 ohms. Examples:1R0 = 1 ohms 102 = 1k ohms 470 = 47 ohms 103 = 10k ohms 101 = ohms 104 = k ohms 105 = 1 megohms protective coat resistor layer inner electrode nickel layer Nu layer For Series (% -F olerance) 4 DIGI SYSEM - First three digits are significant and fourth digit is multiplier, R indicates decimal on values under 10 ohms Examples:10R0 = 10 ohms 3 = k ohms 0 = ohms 4 = 1 megohms 1 = 1k ohms 1052 = 10.5k ohms 2 = 10k ohms 2213 = 221k ohms 3 olerance F=1%, J=5% tb t1 aluminum substrate protective coat 4 ape & Reel here is no marking on 0201 product. t t t b Mass (g) CR02 0.6± ± ± ± ± Part Numbering System CR J 0201 = Use for 1% = Use for 5% Nominal Resistance 3- E24 Series EX 2.2Ω=2R2 Ω=101 Resistors 4- E96 Series EX 10.2R=10R2 10kΩ=2 olerance F = 1% J = 5% Packaging = ape 000 IS EECRONICS, INC : 3506D ake Center Dr, Santa na, C Coldwater Canyon, el: North Hollywood. California Fax: Phone (1) oll Free (00) Fax (1) C4
3 Features: Small size and light weight Suitable for both flow and re-flow soldering Reduction of assembly costs and matching with placement machines hick Film Chip Resistors pplications: utomotive industry Medical and military equipment elecommunication equipment Computers Pocket calculators Radio and tape recorders V tuners and video cameras Note: 1. Special resistance tolerance requirement available on a case to case basis. Please indicate when ordering. 2. Special.C.R. requirements can be supplied on a case to case basis. Please indicate when ordering. Construction Specialty Chip Resistors: PCR Power Chip Resistors FCR Fusible Chip Resistors For detailed specifications, please consult factory. Part Numbering System 103 J = Use for 1% = Use for 5% Nominal Resistance 3- E24 Series EX 2.2Ω=2R2 Ω=101 Resistors 4- E96 Series EX 10.2R=10R2 10kΩ=2 000 olerance J = 5% G = 2% F = 1% D =.5% IS EECRONICS, INC : 3506D ake Center Dr, Santa na, C Packaging 7267 Coldwater Canyon, el: North Hollywood. California Fax: Phone (1) oll Free (00) Fax (1) C5 = ape = ulk
4 hick Film Chip Resistors Power Rating and Dimension Resistive Element Protective Glass Overcoat Solder Plating 90/10 (2 microns min.) Nickel Plating (2 microns min.) Palladium Silver (10 microns min.) lumina Substrate (96% min.) Part No. EI Size Power Rating at 70 C Max. orking Voltage Max. Overload Voltage Operating emp. ( C) olerance % Resistance Range Standard Series 1/16 25V 50V Ω - 1 M Ω 2Ω M Ω 2Ω M Ω 1/10 1/16 (Std) 50V V. 01 Ω - 22 M e g Ω.01Ω 0MegΩ. 01 Ω - 0 M e g Ω 1/ 1/10 (Std) 150V 300V. 01 Ω - 22 M e g Ω. 01 Ω - 0 M e g Ω. 0 1 Ω M e g Ω 1/4 1/ (Std) < 50 m Ω. 01 Ω - 22 M e g Ω. 01 Ω - 0 M e g Ω. 0 1 Ω M e g Ω 1/ Ω M e g Ω 1/ Ω M e g Ω Ω M e g Ω IS EECRONICS, INC : 3506D ake Center Dr, Santa na, C Coldwater Canyon,North el: Hollywood. California Fax: Phone (1) oll Free (00) Fax (1) C6
5 hick Film Chip Resistors Dimensions P o w e r R a t i n g EI Size H t 1/16 1/16 (Std) 1/10 1/10 (Std) 1/ 1/ (Std) 1/4 1/4 1/ ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ± ±0.3 Marking t Marking 1. For Series (%-G, %-J, 0%-K olerances) In,,,, and sizes. 3 DIGI SYSEM - First two digits are significant and third digit is multiplier, R indicates decimal on values under 10 ohms. Examples: 1R0 = 1 ohms 102 = 1k ohms 470 = 47 ohms 103 = 10k ohms 101 = ohms 104 = k ohms 105 = 1 megohms 2. For Series (% -F olerance) in,,,, and sizes. 4 DIGI SYSEM - First three digits are significant and fourth digit is multiplier, R indicates decimal on values under 10 ohms Examples: 10R0 = 10 ohms 3 = k ohms 0 = ohms 4 = 1 megohms 1 = 1k ohms 1052 = 10.5k ohms 2 = 10k ohms 2213 = 221k ohms 3. For Series (% -F olerance) in size 3 DIGI SYSEM (Due to space restrictions) 4. No marking for. SNDRD VUES ND RESISNCE CODE 7267 Coldwater Canyon, North Hollywood. California Phone (1) oll Free (00) Fax (1) C MUIPIER CODE Multiplier C 10 2 D 10 3 E 10 4 F 10 5 G 10 6 H 10 7 X 10-1 Y 10-2 Z CODING FORMU XX X Multiplier Resistance Example: 10.2 kω = 102 x 10 2 Ω = 02C 02 C 33.2 Ω = 332 x 10-1 = 51X 51 X H unit: m/m Marking Examples 10 Ω = 01X 7.5k Ω = 5 150k Ω = 1D 1 Meg Ω = 01E
6 hick Film Chip Resistors aping Specifications in Millimeters (1) vailability Power Rating 1/16 1/16, 1/10 1/10, 1/ 1/, 1/4 1/4 1/2 1 EI Carrier ape Size Fig Material idth Plastic Plastic Plastic Q ty per Reel (pcs) 10,000 5,000 5,000 5,000 4,000 4,000 4,000 (2) ape specifications FIG Max. 1.5 ø -0 EI Size 1.1 Max. 4.0 ± ± ± ± ± ± 0.2 * Same for types 1.15 ± ± 0.05 ± ± 0.2 (3) Embossed plastic tape specification FIG ± ø -0 D C EI Size 2.9 ± ± ± 0.1 * Same for types 3.6 ± ± ± ±0.1 C D F 3.5 ± ± ± ± ± ± ± ± ± 0.1 F.0 ± ± ± ±0.1 (4) Reel Specifications FIG. C. 20 ± 0.5 EI Size ± eader tape: pproximately 250 m/m leader shall be provided at each end of the tape. 2. ccumulative tolerance of feeding hole and chip pocket shall not exceed 0.2mm over 10 pitches. 10 ± 1.5 IS EECRONICS, INC : 3506D ake Center Dr, Santa na, C Coldwater Canyon, el: North Hollywood. California Fax: Phone (1) oll Free (00) Fax (1) C
7 hick Film Chip Resistors Performance Specifications Characteristics est Methods imits emperature coefficient JIS - C Short - time overload JIS - C Insulation resistance JIS - C Dieletric withstanding voltage JIS - C erminal bending JIS - C Soldering Heat JIS - C Solderability JIS - C emperature cycling JIS - C oad life in humidity JIS - C oad ife JIS - C Natural resistance change per temp. degree centigrade. R 2 - R 1 x 10 6 (PPM / C) R 1 (t 2 -t 1 ) R 1 : Resistance value at room temperature (t 1 ) R 2 : Resistance value at room temp. plus C (t 2 ) Permanent resistance change after the application of a potential of 2.5 times RCV for 5 seconds. pply 500V DC between protective coating and termination for 1 minute, then measure. pply 500V C between protective coating and termination for 1 minute. wist of est oard: Y/X=5/90mm for 10 seconds. Dip the resistor into a solder bath having a temperature of 260 C C and hold it for 10 seconds. est temperature of solder 235 C C. Dipping them in solder: 3±0.5 seconds. Resistance change after continuous five cycles for duty cycle specified below: Step emperature ime 1-55 C ± 3 C 30 minutes 2 Room temp 10~15 minutes C ± 2 C 30 minutes 4 Room temp 10~15 minutes Resistance change after 1,000 hours (1.5 hours on 0.5 hour off ) at RCV in a humidity chamber controlled at 40 C ± 2 C and 90 to 95% relative humidity. Permanent resistance change after 1,000 hours operating at RCV, with duty cycle of 1.5 hours on, 0.5 hour off at 70 C ± 2 C ambient. % 1Ω 10Ω ±400PPM/ C 11Ω 10MΩ 00PPM/ C % 10Ω Ω 00PPM/ C 101Ω 1MΩ 00PPM/ C ± 5% olerance ±(2.0%+ 0.1Ω) ± 1% olerance ±(1.0%+ 0.1Ω) 1,000 Mega ohm or more No evidence of flashover mechanical damage, arcing or insulation breakdown ± (1.0% Ω) Resistance change rate is ± (1.0% Ω ) 95% coverage Min. ± 5% olerance ±(1.0%+ 0.05Ω) ± 1% olerance ±(0.5%+ 0.05Ω) ± 5% olerance ±(3.0%+ 0.1Ω) ± 1% olerance ±(1.0%+ 0.1Ω) ± 5% olerance ±(3.0%+ 0.1Ω) ± 1% olerance ±(1.0%+ 0.1Ω) *RCV = Rated Continuous orking Voltage = Rated Power x Resistance Derating Curve -55 C 70 C 5 C mbient temperature ( C) IS EECRONICS, INC : 3506D ake Center Dr, Santa na, C Coldwater Canyon, el: North Hollywood. California Fax: Phone (1) oll Free (00) Fax (1) C9
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_WWxxX_V12 Nov.- 2011
More informationPower chip resistor size 2512 PRC221 5%; 2% FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability.
FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability. APPLICATIONS Power supplies Printers Computers Battery chargers Automotive Converters CD-ROM. QUICK
More informationTC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 1206, 0805, 0603
WF2Q, WF08Q, WF06Q ±%, ±0.5%, ±0.25%, ±0.%, ±0.05% TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 206, 0805, 0603 *Contents in this sheet are subject to change without
More informationDATA SHEET CHIP RESISTORS RT Series 1%; 0.5%; 0.25%; 0.1%
DATA SHEET CHIP RESISTORS Series 1%; 0.5%; 0.25%; 0.1% Product specification Supersedes Date of Sep. 30, 2003 ynsc004 ynsc015 ynsc002 ynsc007 2 SCOPE This specification describes series chip resistors
More informationWR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 10 ASC_WR_V23 APR.- 2015
More informationSPECIFICATION FOR APPROVAL. Approved by
C O N F I D E N T I A L D O C U M E N T SPECIFICATION FOR APPROVAL CONRAD Description : Royalohm Part no.: 0402WGxxxxxTCE (RMC 1/16W (0402) +/- 1%, 5% & Jumper) 0603SAxxxxxT5E (RMC 1/10W-S (0603) +/- 1%,
More informationPulse Withstanding Thick Film Chip Resistor-SMDP Series. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: /// official distributor of Pulse Withstanding Thick Film Chip Resistor-SMDP Series 1. Scope -This specification applies to ~ sizes
More informationType RP73 Series. SMD High Power Precision Resistors. Key Features. Applications. Characteristics - Electrical - RP73 Series - Standard
Key Features n High precision - tolerances down to 0.05% n Low TCR - down to 5ppm/ C n Stable high frequency performance n Operating temperature -55 C to +155 C n Increased power rating - up to 1.0W n
More informationAutomotive and Anti-Sulfuration Chip Resistor 0402
The resistors are constructed in a high grade ceramic body (aluminium oxide). Internal metal electrodes are added at each end and connected by a resistive paste that is applied to the top surface of the
More informationHigh Power Thick Film Chip Resistor 2512
Specifications: Type : MCHP12 Power Rating at 70 C : 2W Working Voltage : 250V Max. Overload Voltage : 500V Max. Dielectric Withstanding Voltage : 500V Temperature Range : -55 C to +155 C Ambient Temperature
More informationDATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/0805/1206/2512. RoHS compliant & Halogen free
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/005/1206/2512 RoHS compliant & Halogen free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE
More informationHigh-ohmic/high-voltage resistors
FEATURES High pulse loading capability Small size. APPLICATIONS Where high resistance, high stability and high reliability at high voltage are required High humidity environment White goods Power supplies.
More informationDATA SHEET GENERAL PURPOSE CHIP RESISTORS RC0402 5%, 1% RoHS compliant & Halogen Free
DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%, 1% RoHS compliant & Halogen Free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE This specification describes series chip
More informationPrecision Leaded Resistors
FEATURES Approved according to CECC 40101-806 Advanced thin film technology Low TC: ± 15 to Precision tolerance of value: ± 0.1 % and ± 0.25 % Superior overall : class 0.05 Wide precision range: 10 Ω to
More informationHigh-ohmic/high-voltage resistors
FEATURES These resistors meet the safety requirements of: UL1676 (range 510 kω to 11 MΩ) EN60065 BS60065 (U.K.) NFC 92-130 (France) VDE 0860 (Germany) High pulse loading capability Small size. APPLICATIONS
More informationSMD High Power Precision Resistors
Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Choice of packages Stable high frequency performance Temperature range -55 C to +155 C Applications Communications
More informationDATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/122/124/162/164/248/324/158/358 TC: 122/124/164
Product specification December 11, 2015 V.2 0 DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/2/4/162/164/248/324/158/358 TC: 2/4/164 RoHS compliant Product specification 2 SCOPE This specification
More informationPulse Proof Thick Film Chip Resistors
Pulse Proof Thick Film Chip Resistors FEATURES High pulse performance, up to kw Stability R/R 1 % for h at 70 C AEC-Q200 qualified Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
More informationDATA SHEET LOW OHMIC HIGH POWER CHIP RESISTORS RL-High power series 5%, 2%, 1% sizes 0805/1206
DATA SHEET LOW OHMIC HIGH POWER CHIP RESISTORS series 5%, 2%, 1% sizes 005/1206 RoHS compliant Product specification Aug 27, 200 V.2 Product specification 2 SCOPE This specification describes RL005/1206
More informationDATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product Specification October 13, 11 V.8 Product
More informationDATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/005/ 1206/1210/121/2010/2512 Product specification August 22, 2014 V.0 Product specification 2 SCOPE This specification
More information50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
More informationSIL Resistor Network. Resistors. Electrical. Environmental. L Series. Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant
Resistors SIL Resistor Network Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant All parts are Pb-free and comply with EU Directive 2011/65/EU (RoHS2) Electrical Standard Resistance
More informationStandard Thick Film Chip Resistors
Standard Thick Film Chip Resistors FEATURES Stability R/R = 1 % for 00 h at 70 C 2 mm pitch packaging option for size Pure tin solder contacts on Ni barrier layer provides compatibility with lead (Pb)-free
More informationATC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors
AC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors Features: Lowest ESR in Class Highest Working Voltage in class 250V Standard EIA Size: 0603 Laser Marking (Optional) RoHS Compliant High
More informationUltra Precision Metal Film Leaded Resistors
Ultra Precision Metal Film Leaded Resistors FEATURES Exceptional low TCR: ± 2 ppm/k to ± 10 ppm/k Super tight tolerance: ± 0.01 % to ± 0.25 % Exceptional overall stability: class 0.02 Wide resistance range:
More informationPrecision Surface Mount Resistors Wirewound or Metal Film Technologies
Precision Surface Mount Resists irewound Metal Film Technologies FEATURES Accding to CECC 40402-801 (wirewound) ide range of ohmic values (0.04 to 1 M) Low temperature coefficient (± 25 ppm/ C available)
More informationPower Resistor Thick Film Technology
Power Resistor Thick Film Technology LTO series are the extension of RTO types. We used the direct ceramic mounting design (no metal tab) of our RCH power resistors applied to semiconductor packages. FEATURES
More informationPart Marking Instructions Chip Resistors
Chip Resistors Part Marking Instructions Part Marking Instructions Chip Resistors 1% Marking The nominal resistance is marked on the surface of the overcoating with the use of 4 digit markings. 0201 and
More informationHigh Ohmic/High Voltage Metal Film Leaded Resistors
, High Ohmic/High Voltage FEATURES Metal film technology High pulse loading (up to 10 kv) capability Small size (0207/0411) Compatible with lead (Pb)-free and lead containing soldering processes Compliant
More informationMetal Film Resistors, Industrial, Precision
CMF Industrial Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics
More informationMetal Film Resistors, Non-Magnetic, Industrial, Precision
Metal Film Resistors, Non-Magnetic, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics
More informationMetal Film Resistors, Industrial, Precision
Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Available Excellent high frequency characteristics Exceptionally
More informationHigh Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
More informationSurface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
More informationCarbon Film Fixed Resistor Axial Leaded
Features Automatically insertable High quality performance Non-Flame type available Cost effective and commonly used Too low or too high values can be supplied on case to case basis Performance Specification
More informationHigh Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to
More informationHigh Ohmic/High Voltage Metal Glaze Leaded Resistors
VR37 High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded
More informationNARROW-PITCH (0.8mm) CONNECTORS P8 SERIES
Socket Header Compliance with RoHS Directive NRROW-PITCH CONNECTORS FOR PC ORDS 3. Perfect for portable devices, the bellows-type provide a strong resistance against falling, impacts, and forced insertions
More informationHigh Ohmic / High Voltage Metal Glaze Leaded Resistors
High Ohmic / High Voltage Metal Glaze Leaded Resistors A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper
More informationATC 800 B Series NPO Ceramic, High RF Power Ultra-Low ESR Multilayer Capacitors
800 Series NPO Ceramic, High RF Power Ultra-ow ESR Multilayer Capacitors Case Size (" x ") Rugged, reliable NPO dielectric Case optimized for highest self resonant frequency s 800 Series offers superb
More informationHigh Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
More informationDATA SHEET THICK FILM CHIP RESISTORS Introduction
DATA SHEET THICK FILM CHIP RESISTORS Introduction Product Specification Product specification 2 Chip Resistor Surface Mount Data in data sheets is presented - whenever possible -according to a 'format',
More informationSurface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified
More informationESCC 4001/026 Qualified ( ) High Stability Thick Film Resistor Chips
ESCC 4001/026 Qualified ( ) High Stability Thick Film Resistor Chips thick film chip resistors are specially designed to meet the requirements of the ESA 4001/026 specification. They have undergone the
More informationSM712 Series 600W Asymmetrical TVS Diode Array
SM712 Series 6W Asymmetrical TVS Diode Array RoHS Pb GREEN Description The SM712 TVS Diode Array is designed to protect RS-485 applications with asymmetrical working voltages (-7V to from damage due to
More informationMCS 0402 AT, MCT 0603 AT, MCU 0805 AT, MCA 1206 AT - Precision www.vishay.com. Precision Thin Film Chip Resistors
Precision Thin Film Chip Resistors FEATURES Rated dissipation P 70 up to 0.4 W for size 1206 AEC-Q200 qualified Approved to EN 140401-801 Superior temperature cycling robustness Sulfur resistance verified
More informationHigh Ohmic (up to 68 MΩ)/ High Voltage (up to 10 kv) Resistors
High Ohmic (up to 68 MΩ)/ A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps.
More informationSMD PTC - Nickel Thin Film Linear Thermistors
SMD PTC - Nickel Thin Film Linear Thermistors Notes (1) Contact if closer TCR lot tolerance is desired. (2) Other R 25 -values and tolerances are available upon request. (3) Rated continuous working voltage
More informationProduct Specification
Product Specification Model No.: DC-240-L01-00-TR Description: H=3.00mm Horizontal SMD DC Power Jacks Pin Shaft Diameter: 0.65mm Packing Method: Tape & Reel (600pcs./R) 1. General 1a. Scope The jacks should
More informationTypes MC and MCN Multilayer RF Capacitors
High-Frequency, High-Power, High-Voltage Chips with Nonmagnetic Option Rugged flexibility and compatibility with FR4 boards make Type MC and MCN capacitors ideal for use where other multilayer caps aren
More informationSURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) Rotor. Wiper. Cover. Pin S T - 2 T A 1 0 0 Ω ( 1 0 1 )
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) COPAL ELECTRONICS RoHS compliant INTERNAL STRUCTURE 8 4 7! 5! 9 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7
More informationProfessional Thin Film MELF Resistors
,, - Professional Professional Thin Film MELF Resistors, and professional thin film MELF resistors are the perfect choice for most fields of rn professional electronics where reliability and stability
More informationAC and Pulse Film Foil Capacitors KP Radial Potted Type
AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions
More informationST-2 SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) FEATURES PART NUMBER DESIGNATION S T - 2 T A 1 0 0 Ω ( 1 0 1 ) RoHS compliant
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) ST- RoHS compliant INTERNAL STRUCTURE 8 4 7 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7 8 9!! 5 Part name Housing
More informationThin Film MELF Resistors
Thin Film MELF Resistors FEATURES MELF resistor with high power rating AEC-Q200 qualified Advanced metal film technology Best in class pulse load capability Intrinsic sulfur resistance Material categorization:
More informationFor board-to-fpc. Narrow Pitch Connectors (0.35mm pitch)
For board-to-fpc Narrow Pitch Connectors (0.35mm pitch) S35 Series New FEATURES 1. 1.7 mm wide slim two-piece type connector Mated height 0.6 mm Smaller compared to A4F series Width: Approx. 44% down
More informationNTC Thermistor:TTC3 Series
Features. RoHS compliant 2. Halogen-Free(HF) series are available 3. Boy size: Ф3mm 4. Raial lea resin coate 5. Operating temperature range: -40 ~+25 6. Wie resistance range 7. Cost effective 8. Agency
More information0.3 mm Contact Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors.
0.3 mm Contact Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors. FH Series (51pos. type) 3.45mm 17.1mm 0.9mm Features 1. Extremely light weight The largest version, with all contacts
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES 800 W at 85 C bottom case temperature Wide resistance range: 0.3 to 900 k E24 series Non inductive Easy
More informationPolymer Termination. Mechanical Cracking 2. The reason for polymer termination. What is Polymer Termination? 3
Polymer Termination An alternative termination material specifically designed to absorb greater levels of mechanical stress thereby reducing capacitor failures associated with mechanical cracking Mechanical
More informationLife Expectancy : Class A Class B Class C Class D 30,000hrs 10,000hrs 3,000hrs 1000hrs
3.2 Motor Run Capacitors : continuous operation ypical Applications : Motor Run Capacitor ideal for various motor applications in washing machine, air conditioner, electric water pump, power factor collection
More informationCeramic Trimmer Capacitors
!Note T3E8.pdf 2.9.2 Ceramic Trimmer Capacitors TZB4 Series.±. Depth.5.4±. dia. Features. Miniature rectangular shape : 4.(W)x4.5(L)x3.(H)mm. 2. Color coded case facilitates identification of capacitance
More informationMBA/SMA 0204, MBB/SMA 0207, MBE/SMA 0414 - Professional www.vishay.com. Professional Metal Film Leaded Resistors
,, - Professional Professional Metal Film Leaded Resistors DESCRIPTION,, and professional leaded thin film resistors are the general purpose resistor for all fields of professional electronics where reliability
More informationPulse Proof, High Power Thick Film Chip Resistors
Pulse Proof, High Power Thick Film Chip Resistors STANDARD ELTRICAL SPIFICATIONS MODEL CASE SIZE INCH CASE SIZE METRIC POWER RATING P 70 W LIMITING ELEMENT VOLTAGE U max. AC/DC -HP e3 FTURES Excellent
More informationThick Film Chip Resistors, Military/Established Reliability MIL-PRF-55342 Qualified, Type RM
Thick Film Chip Resistors, Military/Established Reliability -PRF-55342 Qualified, Type RM MATERIAL SPECIFICATIONS Resistive element Ruthenium oxide Encapsulation Epoxy Substrate 96 % alumina Termination
More informationInterference Suppression Film Capacitors MKP Radial Potted Type
Interference Suppression Film Capacitors MKP Radial Potted Type FEATURES 7.5 mm to 27.5 mm lead pitch Supplied loose in box, taped on reel Material categorization: For definitions of compliance please
More informationhandbook, 2 columns handbook, halfpage 085 CS
FEATURES Polarized aluminium electrolytic capacitors, non-solid, self healing Extended voltage and capacitance range SMD-version, fully moulded, insulated Flexible terminals, reflow and wave solderable
More informationThick Film Resistor Networks, Dual-In-Line, Molded DIP
Thick Film Resistor Networks, Dual-In-Line, Molded DIP FEATURES Isolated, bussed, and dual terminator schematics available 0.160" (4.06 mm) maximum seated height and rugged, molded case construction Thick
More informationMetal Film Resistors, Military, MIL-R-10509 Qualified, Precision, Type RN and MIL-PRF-22684 Qualified, Type RL
Metal Film Resistors, Military, Qualified, Precision, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient Flame retardant
More informationThick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ010 and RZ020 Dual-In-Line, Molded DIP
MDM (Military M831/1 and /2) Thick Film Resistor Networks, Military, MIL-PRF-831 Qualified, Type RZ1 and RZ2 Dual-In-Line, Molded DIP STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL/ PIN NO. MIL STYLE
More informationSD Memory Card Connectors
SD Memory Card Connectors DM Series Withstands higher force of card insertion. Card Standard type Metal cover extends over the back of the connector. Features. Withstands higher force of card insertion
More informationMetal Film Resistors, Military, MIL-R-10509 Qualified, Type RN and MIL-PRF-22684 Qualified, Type RL
CMF (Military RN and RL) Metal Film Resistors, Military, Qualified, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient
More informationHow To Power A Power Control Microprocessor (Power Control) Microprocessor 2 (Power) (Power Power) (Control) (Repower) Microcontroller (Power/Reflow) (Mini) (Microprocessor) (Wired) (Wire
PTC NTC for Surface Mounting Application What is a Thermistor? Thermally Sensitive Resistor Thermistor Positive Temperature Coefficient PTC Negative Temperature Coefficient NTC Characteristics of Thermistors
More informationMADP-000504-10720T. Non Magnetic MELF PIN Diode
MADP-54-172T Features High Power Handling Low Loss / Low Distortion Leadless Low Inductance MELF Package Non-Magnetic Surface Mountable RoHS Compliant MSL 1 Package Style 172 Dot Denotes Cathode Description
More informationInsulated Precision Wirewound Resistors Axial Leads
Insulated Precision Wirewound Resistors Axial Leads In wirewound precision resistors, the series holds a leading position in professional applications whenever an excellent stability of the ohmic value
More informationAxial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 50 V DC, 100 V DC and 200 V DC
Axial and Radial Leaded Multilayer Ceramic Capacitors for Automotive Applications Class 1 and Class 2, 5 V DC, 1 V DC and 2 V DC DESIGNING For more than 2 years Vitramon has supported the automotive industry
More informationMetal Film Resistors, Industrial, Flameproof
End of Life - August 13 Metal Film Resistors, Industrial, Flameproof STANDARD ELECTRICAL SPECIFICATIONS FEATURES Small physical size Low cost resistors have the ability to withstand overloads up to times
More informationDC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type FEATURES 15 mm to 27.5 mm lead pitch. Supplied loose in box and taped on reel Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
More informationKit 27. 1W TDA7052 POWER AMPLIFIER
Kit 27. 1W TDA7052 POWER AMPLIFIER This is a 1 watt mono amplifier Kit module using the TDA7052 from Philips. (Note, no suffix.) It is designed to be used as a building block in other projects where a
More informationProfessional Thin Film Chip Resistors
Professional Thin Film Chip Resistors FEATURES Operating temperature up to 175 C for 1000 h Rated dissipation P 85 up to 0.4 W for size 1206 AEC-Q200 qualified Approved to EN 140401-801 Sulfur resistance
More informationHow To Control A Power Supply On A Powerline With A.F.F Amplifier
INTEGRATED CIRCUITS DATA SHEET Sound I.F. amplifier/demodulator for TV File under Integrated Circuits, IC02 March 1986 GENERAL DESCRIPTION The is an i.f. amplifier with a symmetrical FM demodulator and
More informationDC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type MKT80 FEATURES AEC-Q00 qualified (rev. D) for PCM. mm (for larger available components on request) High temperature capabilities, up to 0 C Capacitance up to 60
More informationNBB-402. RoHS Compliant & Pb-Free Product. Typical Applications
Typical Applications Narrow and Broadband Commercial and Military Radio Designs Linear and Saturated Amplifiers 0 RoHS Compliant & Pb-Free Product NBB-402 CASCADABLE BROADBAND GaAs MMIC AMPLIFIER DC TO
More informationHigh Surge Axial Cemented Wirewound Resistors
High Surge Axial Cemented Wirewound Resistors FEATURES High voltage surge (up to 12 kv) withstanding capability Non flammable silicon cement coating High grade ceramic core Material categorization: for
More informationMetal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description
MLN SurgeArray TM Suppressor RoHS Description The MLN SurgeArray Suppressor is designed to help protect components from transient voltages that exist at the circuit board level. This device provides four
More informationINTEGRATED CIRCUITS DATA SHEET. TDA7052 1 W BTL mono audio amplifier. Product specification File under Integrated Circuits, IC01
INTEGRATED CIRCUITS DATA SHEET TDA7052 1 W BTL mono audio amplifier File under Integrated Circuits, IC01 July 1994 GENERAL DESCRIPTION The TDA7052 is a mono output amplifier in a 8-lead dual-in-line (DIL)
More informationHigh Stability - High Temperature (230 C) Thin Film Wraparound Chip Resistors, Sulfur Resistant
High Stability - High Temperature (230 C) Thin Film Wraparound Chip Resistors, Sulfur Resistant INTRODUCTION For applications such as down hole applications, the need for parts able to withstand very severe
More informationGuide for Molded Tantalum Capacitors
Guide for Molded Tantalum Capacitors INTRODUCTION Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability,
More informationPower Dissipation Considerations in High Precision Vishay Sfernice Thin Film Chips Resistors and Arrays (P, PRA etc.) (High Temperature Applications)
VISHAY SFERNICE Resistive Products Application Note ABSTRACT On our thin film chips resistors and arrays the main path for the heat, more than 90 %, is conduction through the body of the component, the
More informationGas Discharge Tube (GDT) Products CG5 and SL0902A Series. CG5 and SL0902A Series
Description Agency Approvals AGENCY AGENCY FILE NUMBER E128662 2 Electrode GDT Graphical Symbol Littelfuse Broadband Optimized SL0902A Series offers high surge ratings in a miniature package. Special design
More informationUltra low ohmic Metal plate / High power type Shunt Resistors
Ultra low ohmic Metal plate / High power type Shunt Resistors PSR Series Features 1) High power class up to 4 to 5W. 2) The lineup of ultra-low resistance value : correspondence from 0.2m 3) Excellent
More informationAluminum Electrolytic Capacitors Axial Miniature, Long-Life
Aluminum Electrolytic Capacitors Axial Miniature, Long-Life 38 AML 0 ASM smaller dimensions Fig. QUICK REFERENCE DATA DESCRIPTION Nominal case sizes (Ø D x L in mm) 6.3 x.7 to 0 x 5 VALUE 0 x 30 to x 38
More informationATC 100 C Series Porcelain High RF Power Multilayer Capacitors
A Series Porcelain High RF Power Multilayer apacitors ase Size apacitance Range (.250" x.250") 1 pf to 2700 pf High Q Ultra-Stable Performance ow ESR/ES High RF urrent/voltage High RF Power High Reliability
More informationOptocoupler, Phototransistor Output, Dual Channel, SOIC-8 Package
ILD25T, ILD26T, ILD27T, ILD211T, ILD213T Optocoupler, Phototransistor Output, Dual Channel, SOIC-8 Package i17925 A1 C2 A3 C4 i17918-2 8C 7E 6C 5E DESCRIPTION The ILD25T, ILD26T, ILD27T, ILD211T, and ILD213T
More informationDATA SHEET. TDA1510AQ 24 W BTL or 2 x 12 W stereo car radio power amplifier INTEGRATED CIRCUITS
INTEGRATED CIRCUITS DATA SHEET 24 W BTL or 2 x 12 W stereo car radio File under Integrated Circuits, IC01 January 1992 GENERAL DESCRIPTION The is a class-b integrated output amplifier encapsulated in a
More information3216 Ceramic Chip Antenna for Bluetooth/WLAN Application
ANTENNA PRODUCTS Mars Liu C.T.Lee Page 1 sheet 190-1 A4 for Bluetooth/WLAN Application Preliminary Product Specification Quick Reference Data Centre Frequency Bandwidth VSWR Polarization Azimuth Beamwidth
More informationSPECIFICATION. Topview 5550 SMD LED IWS 505-RB. Product : Topview 5550 SMD LED Part No : IWS-505-RB Customer : Date : 2007. 11. 10 Ver.1.0.
SPECIFICATION Product : Topview 555 SMD LED Part No : Customer : Date : 27.. Ver.. Customer : Approval Manufacturer : ITSWELL Co., LTD Proposed By Approval Comment Suwon Company : 442-9, 82 Uman Industrial
More informationContents. 12. Lot Number 10. 13. Reel Packing Structure 11. 14. Precaution for Use 13. 15. Hazard Substance Analysis 14. 16. Revision History 18
Rev : 00 ISSUE NO : DATE OF ISSUE : 2009. 04. 10 S P E C I F I CATION MODEL : SLHNNWW629T1S0U0S0 [Rank : (S0), (U0), (S0)] HIGH POWER LED - SUNNIX6 CUSTOMER : CUSTOMER CHECKED CHECKED APPROVED SAMSUNG
More informationAluminum Electrolytic Capacitors Power Eurodin Printed Wiring
Aluminum Electrolytic Capacitors Power Eurodin Printed Wiring 00/0 PEDPW Fig. QUICK REFERENCE DATA DESCRIPTION VALUE 00 0 Nominal case size (Ø D x L in mm) x 0 to 0 x 00 Rated capacitance range 0 μf to
More information