Installing the Y Axis Extension Kit on the Taig Mill

Size: px
Start display at page:

Download "Installing the Y Axis Extension Kit on the Taig Mill"

Transcription

1 Installing the Y Axis Extension Kit on the Taig Mill Congratulations on your purchase of the Y Axis Extension Kit for the Taig mill. This kit adds ¾ of travel to the Y axis, increasing the travel from 5.5 to It also increases the distance from the spindle centerline to the column from 5.50 to 6.25 (4.75 to 5.00 from spindle centerline to Z axis way). Installation is straight forward, requires no machining and is easily reversed should the need arise. Contents of kit (Figure 1) 2 ea - End Plate Spacer (A) 1 ea - Headstock Plate Spacer (B) Note: Newer Taig Mills will have a Headstock Spacer Plate with 8 holes 2 ea x 1½ SHCS (C) 4 ea x 1¼ SHCS (D) (Note: SHCS = Socket Head Cap Screws) The following items are not shown 2 ea x ⅜ Phillips Machine Screws 2 ea KEP Nuts 4 ea - #8 Flat Washers C A B Tools Needed 5/32 Allen Wrench (ball end preferred) 3/32 Allen Wrench 9/64 Allen Wrench (optional) 7/8 Wrench (for column nut) Tools Needed for Z Axis and Belt Pulleys Alignment D Figure 1 A variety of tools can be used for the alignment of the Z axis and belt pulleys. The ones listed here are used during these instructions. There are alternate methods of aligning the Z axis and belt pulleys. Use what ever method works best for you with the tools you have at hand. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 1 info@wildhorse-innovations.com

2 Dial Indicator and Stand -OR- Indicol Style Indicator and Stand (Magnetic stand preferred for either indicator) Steel plate for mounting magnetic indicator to machine table T-Nuts and clamps for mounting steel plate to machine table 4-5 Angle Block -OR- 123 Block T-Nuts, bolts and hold down clamps for securing angle block or 123 block to machine table Please refer to the parts explosion found at the bottom of for additional information on the construction of the Taig mill. DISCLAIMER Application of this modification to your mill may result in voiding the manufacturer s warranty. In addition, the techniques used by the installer of this modification are beyond the control of Wildhorse Innovations, LLC. For these reasons, Wildhorse Innovations, LLC assumes no responsibility for the installation or performance of this modification, or any damage to the customer s machine or the performance thereof. By proceeding with the installation of this modification, the customer assumes full responsibility for the quality and performance of this modification and any damage to the machine or the voiding of the manufacturer s warranty. If you do not agree with these terms, your sole remedy is the return of the product, complete and in its original form, to Wildhorse Innovations, LLC. Please obtain an RMA and instructions for the return of the product by ing returns@wildhorse-innovations.com or by writing to Wildhorse Innovations, LLC at Attn: Returns, PO Box 234, Plains, MT Upon receipt of the product complete and in its original condition, Wildhorse Innovations, LLC will refund the purchaser s full purchase price, less any shipping and handling fees. Products returned without an RMA will be refused. Extending the Y Axis Table Travel The ¾ extension of the Y axis table travel on the Taig mill is made possible by the fact that the lead screw on the Y axis is longer than needed for the 5 ½ stock Y axis travel. Additionally, the Y axis ways are long enough to accommodate the additional travel. The saddle ways will overhang the fixed ways by a small amount when the full 6 ¼ travel is used. However, this is not a problem since the machine is designed to accommodate a like amount of overhang at the rear of the ways when the saddle is at the rearmost (nearest the column) limit of travel. The extension of the Y axis travel can be accomplished without removing the saddle, lead screw, lead screw handle or stepper motor. Warning: When applying this modification to a CNC equipped machine, use caution when handling the Y axis stepper motor and lead screw. The weight of the stepper motor should be supported with blocks under the stepper motor or by another suitable method. NEVER allow the weight of the stepper motor to be supported by the lead screw. Doing so can damage the threads or bend the lead screw. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 2

3 Step 1: Move the machine table to a position midway between the travel limits on the Y axis. Center the table on the X axis. Position the Z axis about midway up the column. Step 2: Remove power from the machine and, if the machine is CNC equipped, remove power from the controller, computer and any other devices connected to the machine. Step 3: Fold the Y Axis Front Way Cover back over the table. Optionally the Front W ay Cover can be removed using the 9/64 Allen wrench to remove the two 8-32 x ½ SHCS s which secure the way cover to the Saddle. This may be a good time to remove both way covers and clean them using hot water, dish washing soap and a stiff brush. The 8-32 x ½ machine screws and matching washers and nuts are provided as replacements for the screws securing the W ay Cover Stiffeners and way covers at the center hole in the assembly. 2A 2B (Obscured by motor mount in this photo.) Step 4: (Reference Figure 2) Using a 5/32 Allen wrench, loosen and remove the two x ¾ SHCS s which secure the Y Axis End Plate to the Saddle (2A and 2B). If this is a CNC machine, be sure to support the weight of the stepper motor with scraps of wood or any other suitable support. Figure 2 Step 5: (Reference Figure 3) Carefully slide the entire Saddle, Y Axis Lead Screw, End Plate and Lead Screw Handle (or stepper motor, if CNC equipped) outwards, opening a gap of about 1 between the End Plate and Machine Base. Be sure to maintain support of the stepper motor on CNC equipped machines. Instructions continue on page 4 1 gap Figure 3 Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 3

4 Step 6: (Reference Figures 4 & 5) Insert the 2 End Plate Spacers (4A) between the Y Axis End Plate and the Machine Base. Hold the spacers in position using the two x 1½ SHCS (5A and 5B). Step 7: (Reference Figure 6) carefully slide the entire Saddle, Y Axis Lead Screw, End Plate and Lead Screw Handle (or stepper motor, if CNC equipped) inwards, closing the gap between the End Plate, Spacers and Machine Base. Be sure to support the stepper motor on CNC equipped machines. Tighten the two x 1½ SHCS securely. 4A This completes the installation of the Y Axis Travel Extension Kit. Test the installation by moving the table through the full range of movement on the Y axis. Assure that the Lead Screw is parallel to the travel path of the Table. The close tolerances held during the manufacture of the Spacers should eliminate the need for any adjustment. However, should you find that the alignment of the Lead Screw needs adjustment, there is a small amount of adjustment available by loosing the two x 1½ SHCS s and repositioning the End Plate. Figure 4 If you have limit or home switches mounted on the Y axis they may need to be adjusted to compensate for the extended travel. Switches which are activated by the rearward movement of the Y axis should not need adjustment as we have not made any changes to the rear limit of the table movement. Switches at the forward limit of travel of the Y axis will most likely need adjustment to accommodate the additional ¾ of travel. 5A Figure 5 5B The two 8-32 x ½ screws are provided to replace the center screws on the way cover mounts. I have seen several machines with the nuts missing because no lock washer was used in the initial installation. Use them as you see fit. Figure 6 Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 4

5 Installing the Z Axis Headstock Plate Spacer With the installation of the Y Axis Extension Kit, you have extended the range of movement of the Y axis by ¾. However, the spindle to column distance must be increased in order to take advantage of this increase in the range of movement. Installation of the Headstock Plate Spacer increases the spindle to column distance by ¾. NOTE: Newer Taig mills have Headstock Mounting Plates with 8 holes instead of 6. Your kit will include a Headstock Plate Spacer with 6 or 8 holes, depending upon which model you ordered. The number of holes in no way alters the following instructions. A cautionary note here: Although the installation of the spacer is straightforward, the process of installing the spacer will invariably result in the Spindle Headstock being out of alignment. Realignment of the Spindle Headstock is straightforward, but requires precision tools. The results of the alignment will only be as good as the accuracy of the tools used and the care taken by the installer. It is our objective that the instructions given here are detailed and complete enough to allow a person with little or no knowledge of these alignment procedures to successfully setup the mill for accurate operation. In addition to the step by step instructions and illustrations provided, the reasoning behind our procedures is outlined. Most of the pictures and illustrations in these instructions show the Spindle M otor, and in some cases, the Mill Table, removed. The table need not be removed during the process of installing the Headstock Plate Spacer. The removal of the motor is optional, as will be explained in the first section of the instructions. 7A Step 8: Remove the Spindle M otor. Although it is possible to install the Headstock Plate Spacer and perform the subsequent alignment procedures without removing the motor, because the motor is quite heavy and the weight of the motor is off-center in relation to the Spindle Block, the process is made considerably more difficult with the motor installed. Therefore it is highly recommended that the motor be removed. Step 8a: (Reference Figure 7) Disconnect the Motor Power Cable at the On/Off Switch (7A). Figure 7 Instructions continue on next page. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 5

6 Step 8b: (Reference Figure 8) Using a 5/32 Allen wrench, loosen the two x ¾ Motor Mounting Screws (8A & 8B). Remove the Spindle Belt. While supporting the motor, remove the screws and washers. (A long shaft, minimum 9, T-handle Allen wrench is very useful for this procedure.) Set aside the motor, screws and washers. These are two of the few screws on this machine that use washers and the replacement of the washers is critical. As you remove the M otor Mounting Plate, carefully inspect for any shims between it and the Motor Mounting Block (10B), note their position and set them aside with the motor (most machines will not have shims.) 8A 8B Figure 8 Step 9: (Reference Figure 9) Using a 5/32 Allen wrench, loosen the Spindle Headstock Mounting Clamp (9A) about ½ turn. It is not necessary to remove this screw entirely. Be sure to support the Spindle Headstock while loosening the screw as it may slide off of the Headstock Mounting Plate once the clamping screw is loosened. 9A Figure 9 Step 10: (Reference Figure 10) Slide the Spindle Headstock (10A) off of the Headstock Mounting Plate (10C). The headstock can be slide either up or down to remove it. If the headstock does not slide easily, loosen the mounting clamp screw (9A) another ¼ to ½ turn until the headstock removes easily. 10B 10C Note that the Spindle Motor Mounting Block (10B) will remain attached to the headstock. 10A Figure 10 Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 6

7 Step 11: (Reference Figure 11) Using a 5/32 Allen wrench, loosen and remove the four x ½ SHCS s (11A, 11B, 11C & 11D). This will allow the Headstock Mounting Plate to be removed. Notice that there are six holes in the mounting plate and 8 threaded holes in the Z Axis Main Body. Make a note of the position and the mounting plate and which holes are being used on your machine. As a side note, the variety of holes allows not only the vertical adjustment of the spindle position, but by rotating the mounting plate 90 degrees the spindle may be used in the horizontal position. 11A 11C 11B 11D Figure 11 Step 12: (Reference Figure 12)) Using the four x 1¼ SHCS s, reattach the Headstock Mounting Plate (12A) to the Z Axis Main Body (12B), inserting the Headstock Plate Spacer (12C) between the two. Be sure to use the same mounting holes that were used when the Headstock Mounting Plate was removed. 12B 12A Instructions continue on next page. 12C Figure 12 Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 7

8 Alignment of Column and Spindle to the Table The ultimate objective of aligning the Spindle to the Table is to not only have the Spindle axially aligned at right angles to the table surface, but also to have the VERTICAL MOVEMENT of the Spindle at right angle to the table surface. Many instructions and tutorials on the Taig Mill will focus on a method known as Tramming to accomplish this alignment. However, tramming alone does not take into consideration that the Taig Mill has several points of potential misalignment that are not found on a conventional mill. This makes the alignment of the Taig Mill somewhat more involved than the alignment of a conventional mill. However, this alignment can be performed with a few simple precision tools which should be present in any machinist s toolbox. Figure 13 Figure 13 illustrates the possible misalignment that can occur when only tramming has been used. The misalignment is exaggerated for illustrative purposes. In this illustration, the spindle is shown to be aligned perpendicular to the table surface (The actual spindle is removed here for purposes of clarity. The spindle alignment is represented by the Z-Axis Headstock Mounting Plate.) However, because the Z-Axis Headstock Mounting Plate is mounted to the Z-Axis Column and Main Body with 4 screws WITHOUT ANY ALIGNMENT PINS or other mechanism to assure alignment, it is possible, and likely, that the Z-Axis Headstock Mounting Plate and Z-Axis Column and Main Body will not be in alignment with each other. This results in the condition illustrated in Figure 13 where the spindle is in alignment with the table but the Column is not perpendicular to the table. Many procedures for aligning the column call for the use of a machinist s square to align the column. This is adequate for rough alignment of the column, but for maximum accuracy, more refined procedures are required. Our procedures for this process follow in this document. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 8

9 Note: In order to avoid confusion with step numbering in these instructions, the step numbers will continue in sequence from the previous installation sections. Step 13: (Reference Figures 14 & 15) Reinstall the Spindle Headstock by mating the V ways on the headstock with the V ways in the Headstock Mounting Plate, sliding the headstock into place and tightening the Spindle Headstock Mounting Clamp (15A) Instructions continue on next page. Figure 14 15A Figure 15 Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 9

10 Indicator Indicator Base clamped to Headstock Vertical Surface Angle Plate -or- 123 Block Figure 16 Step 14: (Reference Figure 16) Using Figure 16 as a reference, set up an indicator and angle plate (or 123 block) as shown (angle place mounted to table, indicator mounted on the Spindle Headstock). The Spindle Headstock is made of aluminum so a magnetic mount will not adhere to it and must be mounted using a clamp. In Figure 16 the base is secured to the headstock using a C-Clamp. The longer the length of the vertical surface the more accurately you can set the column s perpendicularity. Using whatever movement controls you have available (handles on manual mill or jogging on CNC mill), move the Z axis so that the indicator moves up and down along the full length of the vertical surface. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 10

11 A Figure 17 If alignment of the column is needed, loosen the mounting nut at the bottom rear of the column (reference Figure 17, item A). Use a soft mallet or block of wood to lightly tap the column near the top to achieve proper alignment. Re-tighten the column mounting nut and recheck alignment. Instructions continue on next page. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 11

12 Figure 18 Step 15: (Reference Figures 18 & 19) We have now aligned the column side to side. Although there is no Official adjustment for front to back alignment, now is a good time to check it. Reposition the angle (or 123) block 90 degrees so the face is parallel to the X axis of the mill. Move the Z axis up and down noting any movement in the reading on the indicator. There is no adjustment for misalignment in the front to back tilt of the column, if the column is leaning in this direction, you can loosen the column mounting nut and fabricate shims to place between the two faces of the column mounting disks (Reference Figure 19). Not much shimming should be needed. A shim will result in an approximently alignment change over the full travel of the Z axis. Instructions continue on next page. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 12

13 Insert shims between these surfaces to align front to back tilt of the column. Figure 19 If changes are made to this alignment you will need to repeat Step 14 above. Instructions continue on next page. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 13

14 Narrow flat on this edge. Figure 20 Step 16: (Reference Figure 20) Now that the column is perpendicular to the table in all directions we will align the Spindle Head so that it is vertical in relation to the table surface. First remove the Spindle Headstock then using your indicator and indicator mount, duplicate the setup shown in Figure 20. Since the Taig table is nonmagnetic, I clamped a steel plate to the table so that my magnetic indicator stand will work. Be sure to have your indicator resting on the Headstock Mounting Plate and not on the Headstock Plate Spacer. Note: The Headstock Mounting Plate has a dovetail to which the Spindle Headstock is mounted. This dovetail has a very narrow flat edge on which to rest the indicator point. Do not rest the indicator point on the angled portion of the dovetail or on the Headstock Plate Spacer. Move the Z-Axis up and down, noting any variation in the indicator reading. If adjustment is needed, loosen the four x 1¼ SHCS just enough to adjust the position of the Headstock Mounting Plate. When the Headstock Mounting Plate is aligned perpendicular to the table surface, remove the indicator. Be sure to retighten the four x 1¼ SHCS. You are now ready to re-install the Spindle Headstock. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 14

15 Once the Spindle Headstock is re-installed your mill should be in near perfect alignment. You can use tramming to verify alignment or to realign if the column is tilted for milling or drilling at an angle. But always be sure the column is properly aligned, demonstrated by the procedures contained in this document, before using tramming. Step 17: Re-install the motor by reversing the procedure used to remove it. Since the Spindle Headstock has been removed and re-installed, the motor and spindle pulleys are almost certainly misaligned. Realign the pulleys using whatever method you prefer. Remember that misalignment of these pulleys will result in shortened belt life. Visit our website: For more machine shop supplies and tools. Wildhorse Innovations is the exclusive US Distributor for the Wildhorse Innovations DRO-350 DRO in both kit and assembled form. Your receipt from this purchase entitles you to a 10% discount on your next order of $50.00 or more from our website. Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 15

16 Taig Mill Y Axis Extension Kit Packing List 2 ea - End Plate Spacer 1 ea - Headstock Plate Spacer (6 or 8 hole) 2 ea x 1½ SHCS 4 ea x 1¼ SHCS 2 ea x ⅜ Phillips Machine Screws 2 ea KEP Nuts 4 ea - #8 Flat Washers 1 ea Instructions Set Copyright by Wildhorse Innovations All rights reserved. Reproduction in whole or part without written permission is prohibited. Page 16

Lathe Milling Attachment

Lathe Milling Attachment Lathe Milling Attachment By L C. MASON BY CLEVERLY stacking cold-rolled flat stock together, T-slots and slide for this lathe milling attachment are made without costly machinery. In fact, only two tools,

More information

Pulleys and Belt. Install the Major Accessory and Pulley. Install the Motor Pulley NOTE. Align the Motor Pulley and the Tool Pulley NOTE

Pulleys and Belt. Install the Major Accessory and Pulley. Install the Motor Pulley NOTE. Align the Motor Pulley and the Tool Pulley NOTE Pulleys and Belt Pulley Guard - 505862 Install the Major Accessory and Pulley 1. Place the short end of the mounting base holes, and insert - but don t tighten - the setscrews. If the Major Accessory has

More information

6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:

6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included: Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:

More information

3. Loosen 3 x grub screws in the Dec end cap and unscrew the cap and counterweight shaft. NEQ6 Belt Modification Kit.

3. Loosen 3 x grub screws in the Dec end cap and unscrew the cap and counterweight shaft. NEQ6 Belt Modification Kit. NEQ6 Belt Modification Kit. Thank you for your purchase. Please read these instructions fully before fitting. Your package should contain 2 off 47 & 2 off 12 tooth aluminium pulleys 2 off belts 6mm wide

More information

SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS

SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS SPRITE and BIGFOOT DESKTOP CNC MACHINE KIT ASSEMBLY INSTRUCTIONS README FIRST: Thank you for purchasing your MyDIYCNC Desktop CNC Machine Kit. We hope this versatile and innovative machine brings you many

More information

SELF-STEERING AXLE TABLE OF CONTENTS

SELF-STEERING AXLE TABLE OF CONTENTS SELF-STEERING AXLE TABLE OF CONTENTS Section 1 - Introduction Section 2 - Pre-Installation Check List Section 3 - Ride Height Adjustments Section 4 - Suspension Mount Section 5 - Axle Mount Section 6 -

More information

MGB Chrome Bumper Conversion

MGB Chrome Bumper Conversion MGB Chrome Bumper Conversion Installation Instructions For 1974 1/2-1980 MGB This kit requires cutting, welding, and painting. Professional installation recommended. Note: Every MGB body is slightly different

More information

1000-LB. TRAILER JACK OWNER S MANUAL

1000-LB. TRAILER JACK OWNER S MANUAL 1000-LB. TRAILER JACK OWNER S MANUAL WARNING: Read carefully and understand all INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious

More information

S&G Model 2937 Group 1 Combination Lock

S&G Model 2937 Group 1 Combination Lock Installation and Combination Changing Instructions S&G Model 2937 Group 1 Combination Lock NOTE: READ COMPLETE INSTRUCTIONS BEFORE INSTALLATION These instructions should be followed when installing the

More information

Table of Contents WARNING SYMBOLS AND DEFINITIONS

Table of Contents WARNING SYMBOLS AND DEFINITIONS Table of Contents SAFETY INSTALLATION OPERATION MAINTENANCE Safety... 2 Specifications... 4 Installation... 5 Operation... 8 WARNING SYMBOLS AND DEFINITIONS Maintenance... 9 Parts List and Assembly Diagram...

More information

Multi-Pitch Pitching Machine USER MANUAL

Multi-Pitch Pitching Machine USER MANUAL Multi-Pitch Pitching Machine USER MANUAL TABLE OF CONTENTS Thank you for purchasing the Cimarron Multi-Pitch Pitching Machine. The Cimarron Multi-Pitch Pitching Machine is a high performance pitching machine

More information

Installation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab

Installation Instructions GOOSENECK MOUNTING KIT Chevrolet/GMC 1500/2500/3500 All except 4-door Crew-Cab GOOSENECK MOUNTING KIT Equipment Required: Fastener Kit: F Wrenches: 3/4, 7/8, 15/16 Drill Bits: 1/4 Other Tools: Drill WARNING: Under no circumstances do we recommend exceeding the towing vehicle manufacturers

More information

Field Application Note

Field Application Note Field Application Note Reverse Dial Indicator Alignment RDIA Mis-alignment can be the most usual cause for unacceptable operation and high vibration levels. New facilities or new equipment installations

More information

Auto-belay Cable Replacement Process

Auto-belay Cable Replacement Process Auto-belay Cable Replacement Process Version 2.00 WARNING: The air pressure in the auto-belay system is what causes the cable to be retracted when releasing the cable or climbing the wall with the cable

More information

SET-UP AND INSTALLATION FOR LEAD SCREW CARTRIDGE ASSEMBLY

SET-UP AND INSTALLATION FOR LEAD SCREW CARTRIDGE ASSEMBLY SET-UP AND INSTALLATION FOR LEAD SCREW CARTRIDGE ASSEMBLY 82-13-1 O-Ring (Rear) The Lead Screw Assembly is shipped separately. Note: Install Electrical and Pneumatic Circuitry. Be Sure electrical and pneumatic

More information

Overview. Milling Machine Fundamentals. Safety. Shop Etiquette. Vehicle Projects Machine Shop

Overview. Milling Machine Fundamentals. Safety. Shop Etiquette. Vehicle Projects Machine Shop Overview Milling Machine Fundamentals Wayne Staats, UW-Madison FSAE Safety Shop Etiquette Before Machining Indicating Calculating Feeds and Speeds Machining Maintenance Safety Respect the machines Common

More information

EZ-Steer Assisted Steering System

EZ-Steer Assisted Steering System EZ-Steer Assisted Steering System Installation Instructions Platform Kit P/N 53059-54 Case IH CVX 1135 CVX 1145 CVX 1155 CVX 1170 CVX 1190 CVX 1195 CVX 135 CVX 145 CVX 155 CVX 175 CVX 195 New Holland TVT

More information

Trillium 40 Axis Spring Tensioner Wire Replacement Instructions

Trillium 40 Axis Spring Tensioner Wire Replacement Instructions Trillium 40 Axis Spring Tensioner Wire Replacement Instructions 1 Overview The objective is to replace the broken axis spring tensioner wire. This requires the following tasks: 1. Remove the seismometer

More information

Slide the new steering column shaft through the steering column from the driver compartment.

Slide the new steering column shaft through the steering column from the driver compartment. Slide the new steering column shaft through the steering column from the driver compartment. Push the column shaft through the steering column until the machined end is out past the column lower bushing.

More information

The Bonelle Tool and Cutter Grinder

The Bonelle Tool and Cutter Grinder The Bonelle Tool and Cutter Grinder The grinder was constructed about 1987 and exhibited at the 89th Model Engineering exhibition where it was awarded a bronze medal (see ME Vol164 No 3868 page 273). Subsequently

More information

Dismantling and Reassembly Guide

Dismantling and Reassembly Guide Super X3 Mill Dismantling and Reassembly Guide A picture story book to help you dismantle and reassemble your Sieg Super X3 Mill Arc Euro Trade Ltd. 10 Archdale Street, Syston, Leicester, LE7 1NA. Web:

More information

Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors

Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors Installation Manual Elo Touch Solutions Wall-mounting Kit for the 5501L IDS Touchmonitors SW602206 Rev B Table of Contents Chapter 1: Safety Warning... 3 Chapter 2: Kit Contents... 4 Included in Kit...

More information

AZEK Rail Install Guide

AZEK Rail Install Guide TRIM MOULDING DECK PORCH RAIL PAVERS AZEK Rail Install Guide Installing AZEK Rail with CableRail by Feeney... 1 Installing CableRail by Feeney for AZEK Rail... 7 Installing AZEK Rail Stairs with CableRail

More information

OWNER S MANUAL Table Tennis Table Patent Pending

OWNER S MANUAL Table Tennis Table Patent Pending OWNER S MANUAL Table Tennis Table Patent Pending Be sure to write your model number and serial number here for future reference. You can find these numbers printed on the bottom of the table. MODEL # T8179

More information

TABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2

TABLE OF CONTENTS. I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 BAL Accu-Slide System I. Table of Contents TABLE OF CONTENTS I. TROUBLESHOOTING... 2 - Section 1.01: Common Problems/Solutions... 2 II. GETTING STARTED... 5 - Section 2.01: Tools You Will Need... 5 - Section

More information

STEERING SYSTEM - POWER

STEERING SYSTEM - POWER STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and

More information

SLACK PERFORMANCE KARTS

SLACK PERFORMANCE KARTS SLACK PERFORMANCE KARTS SET UP GUIDE Thank you for purchasing a 2013 Slack Axiom Chassis. Performance Mfg. strives to provide you with the very best chassis and components on the market today. Your satisfaction

More information

2003 ACCORD - Automatic Transmission Removal

2003 ACCORD - Automatic Transmission Removal 2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special

More information

Installation Manual. SKU# 21000 series (Base Rails) SKU# 22000 series (Overhead Racks)

Installation Manual. SKU# 21000 series (Base Rails) SKU# 22000 series (Overhead Racks) Installation Manual SKU# 21000 series (Base Rails) SKU# 22000 series (Overhead Racks) Welcome to the world of TracRac! We re delighted that you have chosen TracRac, the ultimate sliding truck rack system.

More information

Installation Guide 2010 BMW S1000RR Full Exhaust System

Installation Guide 2010 BMW S1000RR Full Exhaust System Installation Guide 2010 BMW S1000RR Full Exhaust System!! THIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE!! Congratulations on the purchase of your new TaylorMade

More information

SERVICE MANUAL. Corpus 3G. Seat system for electric wheelchair

SERVICE MANUAL. Corpus 3G. Seat system for electric wheelchair SERVICE MANUAL US Corpus 3G Seat system for electric wheelchair How to contact Permobil Head Office of the Permobil group Produced and published by Permobil AB, Sweden Version 4, 2014-07 Item No.: 205260-US-0

More information

Pump Skid Fabrication for Magnetic Coupling. Rick Soltis Chief Mechanic City of Bedford

Pump Skid Fabrication for Magnetic Coupling. Rick Soltis Chief Mechanic City of Bedford Pump Skid Fabrication for Magnetic Coupling Rick Soltis Chief Mechanic City of Bedford Contents Magnetic Couplings What They Are, How They Work, Where They re Used Fabrication and Manufacturing of Pump

More information

4BT A/C Bracket Directions

4BT A/C Bracket Directions 4BT A/C Bracket Directions This kit will be broken into smaller kits for ease of installation and recognition of hardware. Tools needed for install; 3/8 Ratchet 1/2 wrench 1/2 socket 9/16 wrench 9/16 socket

More information

Express5800/120Ed. Rack Mount Kit Installation Procedures PN: 455-01607-001

Express5800/120Ed. Rack Mount Kit Installation Procedures PN: 455-01607-001 Express5800/120Ed Rack Mount Kit Installation Procedures PN: 455-01607-001 Proprietary Notice and Liability Disclaimer The information disclosed in this document, including all designs and related materials,

More information

cbperformance.com Please read this entire brochure prior to installing your CB Performance Products MAGNASPARK II distributor.

cbperformance.com Please read this entire brochure prior to installing your CB Performance Products MAGNASPARK II distributor. - Easy -wire installation with no external spark box necessary, but can be used with one. - Precision CNC machining and hand assembled construction. This is a premium product. - Accurate super hot spark

More information

AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION

AXLE SHAFTS - FRONT. 1998 Pontiac Bonneville MODEL IDENTIFICATION DESCRIPTION & OPERATION TROUBLE SHOOTING REMOVAL & INSTALLATION AXLE SHAFTS - FRONT 1998 Pontiac Bonneville 1998-99 DRIVE AXLES FWD Axle Shafts - Cars - "C", "G" & "H" Bodies GM Aurora, Bonneville, Eighty Eight, LeSabre, LSS, Park Avenue, Regency, Riviera MODEL IDENTIFICATION

More information

Tri-Homo Style Operation and Maintenance Instructions

Tri-Homo Style Operation and Maintenance Instructions Tri-Homo Style Operation and Maintenance Instructions One Research Drive Stratford, CT 06615 (203) 375-0063 www.sonicmixing.com 1 Installation and Start-up Do not perform following adjustments without

More information

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS PARTS REQUIRED Single QuickStand Parts A (1) QuickStand Unit B (1) Base Plate C (1) Platform D (1) Palm Support E (1) VESA Plate F (6) M8 x 18 mm Flat Head Machine Screws G (4)

More information

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997 Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47

More information

OPERATING INSTRUCTIONS FOR

OPERATING INSTRUCTIONS FOR OPERATING INSTRUCTIONS FOR MEDECO KEY MACHINES FOR MEDECO ORIGINAL, BIAXIAL, MEDECO 3, KEYMARK CLASSIC & KEYMARK X4 PRODUCTS MEDECO HIGH SECURITY LOCKS ASSUMES NO RESPONSIBILITY FOR INJURY OR PROPERTY

More information

2011-14 F250 6 RADIUS ARM KIT

2011-14 F250 6 RADIUS ARM KIT 92154000 Thank you for choosing Rough Country for your suspension needs. 2011-14 F250 6 RADIUS ARM KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,

More information

»Product» Safety Warning

»Product» Safety Warning C1200 Installation Instructions 2007-2016 Chevy/GM 1500 2/4wd 2" Strut Spacer Lift Read and understand all instructions and warnings prior to installation of product and operation of vehicle. Zone Offroad

More information

TracRac G2. Overhead Rack Installation Instructions. TracRac Inc. 994 Jefferson St. FallRiver MA 02721 www.tracrac.com 800-501-1587 IN-42000_B

TracRac G2. Overhead Rack Installation Instructions. TracRac Inc. 994 Jefferson St. FallRiver MA 02721 www.tracrac.com 800-501-1587 IN-42000_B IN-42000_B TracRac G2 Overhead Rack Installation Instructions TracRac Inc. 994 Jefferson St. FallRiver MA 02721 www.tracrac.com 800-501-1587 Thank you for your purchase of a TracRac G2 Sliding Cargo Manaagement

More information

In-Ground Basketball System Owners Manual

In-Ground Basketball System Owners Manual In-Ground Basketball System Owners Manual Customer Service Center N53 W4700 South Corporate Circle Sussex, WI 53089 U.S.A. Write Model Number From Box Here: WARNING! 3 Capable Adults REQUIRED TOOLS AND

More information

Title: Best Practices Removal and Installation of Wheel Assembly (Tire Mounted to Rim Assembly) From Container Chassis

Title: Best Practices Removal and Installation of Wheel Assembly (Tire Mounted to Rim Assembly) From Container Chassis INSTITUTE OF INTERNATIONAL CONTAINER LESSORS IICL Chassis Technical Bulletin CTB 021, February 12, 2015 Title: Best Practices Removal and Installation of Wheel Assembly (Tire Mounted to Rim Assembly) From

More information

Original Assembly Guide

Original Assembly Guide TCT Multipurpose Single Bevel Sliding Compound Mitre Saw Original Assembly Guide Read instructions before assembling this tool. Table of Contents GB Assembly Guide Read instructions before assembling this

More information

Roll-Up Door Maintenance Guide

Roll-Up Door Maintenance Guide R Roll-Up Door Maintenance Guide Cable Replacement on Two Spring Type Balancer Page 1 Panel Replacement - Removable Roller Cover Type Bottom Panel Page 1 Panel Replacement - Removable Roller Cover Type

More information

ReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD

ReadyLift (Part# 66-5075) Strut Extension, Installation Instructions Toyota Tundra New Body Style 2WD & 4WD SAFETY WARNING: recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks

More information

SPIRAL STAIR KIT INSTALLATION MANUAL

SPIRAL STAIR KIT INSTALLATION MANUAL SPIRAL STAIR KIT INSTALLATION MANUAL Effective January 1, 2014 If you have any questions, please call the location that your Stair Kit was purchased from: Broomall, Pennsylvania 1-800-52-7427 Ontario,

More information

TABLE OF CONTENTS. Page 1

TABLE OF CONTENTS. Page 1 TABLE OF CONTENTS CONGRATULATIONS: Easy Start Guide for the Technician... 2 Laser Toe Gauges... 4 Hardware Connections... 5 Printer Connection... 6 Data Accumulator Features... 7 Batteries - Read Out &

More information

Resharpening Companion

Resharpening Companion Resharpening Companion 10950 Correct Angles, Pictures, and Step-By-Step Instructions The Resharpening Companion is meant to be a guide and quick reference to help you resharpen. It is not meant to replace

More information

Gravity Racing Challenge STEM Team Competition Open Class High School Division Car Assembly Plans And Rules

Gravity Racing Challenge STEM Team Competition Open Class High School Division Car Assembly Plans And Rules Gravity Racing Challenge STEM Team Competition Open Class High School Division Car Assembly Plans And Rules 1 Table Of Contents Introduction...Page 3 Floorboard...Page 4 Step One Steering Stop Installation...Page

More information

Structural Holding System

Structural Holding System Structural Holding System Users Manual November 2013 by Vehicle Service Group. All rights reserved. CO8812.1 502071 Rev. - 11/21/2013 CHIEF'S LIMITED ONE-YEAR WARRANTY & LIABILITY Chief Automotive Technologies

More information

Char-Lynn Spool Valve Hydraulic Motors. Repair Information. W Series Geroler Motors

Char-Lynn Spool Valve Hydraulic Motors. Repair Information. W Series Geroler Motors Char-Lynn Spool Valve Hydraulic Motors Repair Information W Series Geroler Motors with Parking Brake 004 Nut Key Ring, Retaining Bearing Ring, Retaining Ring, Retaining Washer (Thick), Pressure Washer,

More information

Installation Instructions:

Installation Instructions: Portable Guardrail System Model Numbers: 7900060, 7900061, 7900062, 7900063 Installation Instructions: Portable Guardrail System This instruction is intended to meet the Manufacturer s Instructions requirement

More information

I BEAM TRACK INSTALLATION

I BEAM TRACK INSTALLATION PDQ 0/700 FESTOON SYSTEM INSTALLATION AND MAINTENANCE INSTRUCTIONS INTRODUCTION The PDQ Festoon System was designed to run on one of three sizes of I-beams: S x., S8 x 8. and S x.. System trolleys must

More information

Section A. GENERAL INFORMATION

Section A. GENERAL INFORMATION Section A. GENERAL INFORMATION I. Description The information and instructions for attaching the sidecar to the right-hand side of the motorcycle are contained in this handbook and must be carefully observed.

More information

Quick Start Guide See Inside for Use and Safety Information

Quick Start Guide See Inside for Use and Safety Information 3 rd Generation Personal 3D Printer Quick Start Guide See Inside for Use and Safety Information The USB Mass Storage Device Contains the User Guide and Quick Start Guide in other Languages Congratulations

More information

Rebuild Instructions for 70001 and 70010 Transmission

Rebuild Instructions for 70001 and 70010 Transmission Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before

More information

RadianceRail Installation Guide

RadianceRail Installation Guide RadianceRail Installation Guide Installing RadianceRail with CableRail by Feeney... 2 Installing CableRail by Feeney for RadianceRail... 7 Installing RadianceRail Stairs with CableRail by Feeney... 10

More information

Wall-Mounting your HP computer. User Guide

Wall-Mounting your HP computer. User Guide Wall-Mounting your HP computer User Guide The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should

More information

12-Volt Negative Ground Installation Instructions

12-Volt Negative Ground Installation Instructions 12-Volt Negative Ground Installation Instructions For Part Number: 1141, 1164, 1165, 1181 CAUTION!!! Before installing, please read the following important information... 1. The Ignitor is designed for

More information

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5

Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 INSTALLATION GUIDE Installation Guide for the TJ LCG PRO Suspension System (Low Center of Gravity) Available 4 or 5 Take every precaution to make this installation a safe procedure. Make safety the number

More information

HT-0095 Mini PV Receptacles 22-32 AWG Crimping Hand Tool. Tool P/N HT-0095

HT-0095 Mini PV Receptacles 22-32 AWG Crimping Hand Tool. Tool P/N HT-0095 HT-0095 Mini PV Receptacles 22-32 AWG Crimping Hand Tool Tool P/N HT-0095 FCI MANUAL P/N 415988-001 Issued: Date (03/12/99) Page 1 of 18 HT-0095 Issued: Date (03/12/99) Page 2 of 18 Introduction Table

More information

Installation Instructions: (Part # SB76880) XRC Armor Front Fender Kit

Installation Instructions: (Part # SB76880) XRC Armor Front Fender Kit WARNING: Check with Local and State laws before installing this accessory! NOTE: Carefully read entire instructions thoroughly before attempting to install this part. Parts Included: Qty Parts Included:

More information

THE HOW AND WHY OF ADJUSTING A DEWALT RADIAL ARM SAW By Roger A. Hill

THE HOW AND WHY OF ADJUSTING A DEWALT RADIAL ARM SAW By Roger A. Hill THE HOW AND WHY OF ADJUSTING A DEWALT RADIAL ARM SAW By Roger A. Hill This is my 1531. Notice the Mr. Sawdust table and the dust box. The frame is bolted to the cabinet After over 40 years of using and

More information

EXPLORE 4-Leg Teaming Table with Screen Share Assembly Instructions

EXPLORE 4-Leg Teaming Table with Screen Share Assembly Instructions EXPLORE 4-Leg Teaming Table with Screen Share Monitor Display Requirements: your flat panel display must confirm to the following requirements. y With the stand removed, the monitor must not exceed 40

More information

LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions

LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions LORTONE LU6X-130 Item # 061-092 LU6X Basic Item # 061-090 LU6X-130 Instructions and Parts List (including LU6X Basic) Operating Instructions Introduction The LU6X is one the most versatile pieces of equipment

More information

Splitting the feed screw nuts and adjusting backlash on a Bridgeport Milling Machine.

Splitting the feed screw nuts and adjusting backlash on a Bridgeport Milling Machine. Splitting the feed screw nuts and adjusting backlash on a Bridgeport Milling Machine. Bridgeport manufactures their milling machines with 0.005 backlash in the feedscrews, which increases over time due

More information

CETAC Z-Drive Assembly

CETAC Z-Drive Assembly CETAC Z-Drive Assembly Replacement Guide Manual Part Number 610144 Rev 1, 2012 CETAC Technologies, Printed in USA Overview This guide describes the necessary steps to replace the Z-drive assembly on your

More information

TABLE OF CONTENTS. Section 1 - Assembling your new pit bike.

TABLE OF CONTENTS. Section 1 - Assembling your new pit bike. Orion Pit Bike Sales Owners Manual (All information and content is the property of Orion Pit Bike Sales. Any attempt to copy or resell is a direct violation of our copyright. All violators will be prosecuted)

More information

Small Flat Panel Lift Arm FSA-1004 and KSA-1004

Small Flat Panel Lift Arm FSA-1004 and KSA-1004 I N S T A L L A T I O N I N S T R U C T I O N S Small Flat Panel Lift Arm FSA-1004 and KSA-1004 The Lift Arm is an accessory that can be used with a broad range of Small Flat Panel Displays. The allows

More information

Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks

Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended

More information

Reachout Lock Replacement for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors

Reachout Lock Replacement for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors for Andersen 2-Panel and 4-Panel 400 Series Frenchwood Gliding, 200 Series Narroline, and Perma-Shield Gliding Patio Doors Thank you for choosing Andersen. For questions call 1-888-888-7020. For more information

More information

16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1

16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 16 April 2012 1032011-F 1994-2002 Dodge Adjustable Track bar with Relocation Bracket 1 BD Adjustable Track Bar w/bracket Dodge 2500-3500 4WD Models 1994-2002 Dodge 1500 4WD Model 1994-2001 P/N# 1032011-F

More information

IMPORTANT SAFETY UPDATE

IMPORTANT SAFETY UPDATE J. H. FLETCHER & CO. Box 2187 Huntington, WV 25722-2187 304/525-7811 FAX 304/525-4025 IMPORTANT SAFETY UPDATE INFORMATION BULLETIN NO. 87 TO: FROM: OWNERS OF ROOF DRILLS THAT ARE NOW USING THE DUST BAG

More information

GPS AutoSteer System Installation Manual

GPS AutoSteer System Installation Manual GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual

More information

Speed-Mat Rectangle Cutter

Speed-Mat Rectangle Cutter Speed-Mat Rectangle Cutter 1 Honeycomb baseboard. 2 Left hold down. 14 3 Bottom hold down. 4 4 Left / right rule. 8 5 8 5 Left / right rule pointer. 1 6 Top / bottom rule. 7 Top / bottom rule pointer.

More information

RETROFITTING THE X3 MILLING MACHINE (2)

RETROFITTING THE X3 MILLING MACHINE (2) RETROFITTING THE X3 MILLING MACHINE (2) Dick Stephen continues with the mechanical modifications. Fitting the ball screws The 12mm 2mm pitch supplied by THK ball screws are delivered with the nut fitted

More information

Electrically Released Brake ER-825, ER-1225 with Pin Drive Armatues for Montgomery Kone

Electrically Released Brake ER-825, ER-1225 with Pin Drive Armatues for Montgomery Kone P-230 819-0466 Electrically Released Brake ER-825, ER-1225 with Pin Drive Armatues for Montgomery Kone Installation & Operating Instructions Contents Introduction........................... 3 Installation

More information

SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12" DUAL BEVEL COMPOUND MITER SAW B27A

SERVICE PARTS LIST PAGE 1 OF 6 BASE ASSEMBLY SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 12 DUAL BEVEL COMPOUND MITER SAW B27A PAGE 1 OF 6 BASE ASSEMBLY 00 0 EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). SPECIFY CATALOG NO. AND NO. WHEN ORDERING PARTS 1 02-80-0050 Thrust Bearing (1) 2 05-80-0510

More information

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement

Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement Navico-Northstar 2kW JRC Radar Package, Scanner Cable Removal and Replacement This work instruction describes the methods and means for which to remove and reinstall optional scanner cable configurations

More information

MKV Golf GTI Rear Brake Service - Replace Pads and Rotors

MKV Golf GTI Rear Brake Service - Replace Pads and Rotors Page 1 Installation Procedures MKV Golf GTI Rear Brake Service - This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of

More information

Thanks for choosing Toroidal. This file is developed to assist you in assembling and aligning Toroidal Dish.

Thanks for choosing Toroidal. This file is developed to assist you in assembling and aligning Toroidal Dish. Assembling Toroidal Thanks for choosing Toroidal. This file is developed to assist you in assembling and aligning Toroidal Dish. With Toroidal dish, you are aiming for more than 1 satellite and therefore

More information

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger

More information

METAL-TURNING LATHE Built from Stock Parts

METAL-TURNING LATHE Built from Stock Parts by Frank Beatty USING STANDARD PARTS and stock materials that are available almost anywhere, you can build this metalworking lathe with only a few tools. Because of simplification of the assembly in order

More information

9,000lb capacity 4 Post Lift Installation Manual

9,000lb capacity 4 Post Lift Installation Manual 9,000lb capacity 4 Post Lift Installation Manual Parts Checklist 1 Main side track with 9/16 hole on cylinder end complete with cylinder, hose and connector 1 Offside track 2 Cross Rails pre-assembled

More information

TL-12 Passenger Car Alignment System

TL-12 Passenger Car Alignment System Operation and Service Manual Laser Guided Wheel Alignment System TL-12 Passenger Car Alignment System 8231 Blaine Road Blaine, WA 98230 360-371-0552 360-371-0553 fax 800-496-3777 toll free www.tru-line.net

More information

R O A D M A S T E R, I N C.

R O A D M A S T E R, I N C. R O A D M A S T E R, I N C. MOUNTING BRACKET KIT 14 8 7 4 13 5 6 ITEM QTY NAME MATERIAL 1...6...1/2" x 2 1/2" BOLT... 350099-00 2...2...1/2" x 1 1/2" BOLT... 350095-00 3...8...1/2" LOCK WASHER... 350309-00

More information

Congratulations on your purchase of the Great Planes SLOT MACHINE, the first truly easy way to cut hinge slots in your model airplanes.

Congratulations on your purchase of the Great Planes SLOT MACHINE, the first truly easy way to cut hinge slots in your model airplanes. INSTRUCTION MANUAL Congratulations on your purchase of the Great Planes SLOT MACHINE, the first truly easy way to cut hinge slots in your model airplanes. The Slot Machine you have purchased is equipped

More information

Wiper Motor Marinco 2.5. Installation Instructions

Wiper Motor Marinco 2.5. Installation Instructions Wiper Motor Marinco 2.5 Installation Instructions Wiper Motor Marinco-2.5 The Marinco 2.5 Wiper Motor Offers the Following Features: Fully sealed base and housing which allows installation in outdoor wet

More information

CONGRATULATIONS! TABLE OF CONTENTS. 1 Safety Warnings 2 About Your Wheels 3 Setting Up Your Wheels 7 Care and Cleaning 8 Warranty

CONGRATULATIONS! TABLE OF CONTENTS. 1 Safety Warnings 2 About Your Wheels 3 Setting Up Your Wheels 7 Care and Cleaning 8 Warranty WHEEL MANUAL CONGRATULATIONS! Congratulations on your purchase of Oval Concepts Wheels. Developed to perform at a high level, it is important that you follow the operation and maintenance instructions

More information

1500 Follow Spot Yoke

1500 Follow Spot Yoke = 1500 Follow Spot Yoke Rev 1.1 2004 City Theatrical, Inc. Getting Started with the City Theatrical Follow Spot Yoke Congratulations on the purchase of your City Theatrical Follow Spot Yoke. The City Theatrical

More information

ARTICLE BEGINNING APPLICATION IDENTIFICATION DESCRIPTION LUBRICATION & ADJUSTMENT TROUBLE SHOOTING. MANUAL TRANSMISSIONS Saab 5-Speed Transaxle

ARTICLE BEGINNING APPLICATION IDENTIFICATION DESCRIPTION LUBRICATION & ADJUSTMENT TROUBLE SHOOTING. MANUAL TRANSMISSIONS Saab 5-Speed Transaxle Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Saab 5-Speed Transaxle APPLICATION TRANSMISSION APPLICATION ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Vehicle Application Transmission

More information

Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN

Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Sliding Barn Door Hardware Installation Instructions BALDUR and ODEN Installation Instructions Structural Information For standard systems and most custom single door opening systems. General Overview

More information

TRANS-05, Torque Tube Removal, Rebuilding, and Installation

TRANS-05, Torque Tube Removal, Rebuilding, and Installation TRANS-05, Torque Tube Removal, Rebuilding, and Installation Tools Metric Wrench Set Metric Socket Set Jack Stands (6 minimum) Floor Jack 8mm Cheesehead socket (also referred to as 12 point internal socket

More information

No. 57 Receiver Sight No. 57 SML Receiver Sight No. 66 Receiver Sight

No. 57 Receiver Sight No. 57 SML Receiver Sight No. 66 Receiver Sight No. 57 Receiver Sight No. 57 SML Receiver Sight No. 66 Receiver Sight MOUNTING AND ADJUSTING MOUNTING LYMAN NO 57 RECEIVER SIGHT The No. 57 Sight is designed primarily for rifles with round receivers.

More information

92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540

92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 92-95 CRX Rear Kit Part No. 75540 www.airliftperformance.com MN-514 (06409) NPR 4762 Please read these instructions completely before proceeding with installation

More information

Rules of Actuator and Guide Alignment in Linear Motion Systems

Rules of Actuator and Guide Alignment in Linear Motion Systems Rules of Actuator and Guide Alignment in Linear Motion Systems By Gary Rosengren, Director of Engineering Tolomatic, Inc. About the Author Gary Rosengren is Director of Engineering at Tolomatic and has

More information

PRS Y-axis EChain Installation

PRS Y-axis EChain Installation PRS Y-axis Energy Chain Installation Page -1- PRS Y-axis EChain Installation This document shows how to install the Energy chain (Echain) on the Y-axis on ShopBot PRS and PRS BT models. Note that the dust

More information