A INSTALLATION DIMENSIONS

Transcription

1 PRODUCTS INSTALLATION INSTRUCTIONS D641E MODELD641E Description AC and DC dual flusher Sensor panel Switching Power Adapter Battery box Round head screw Water connector Flat washer Body wall Silicone sucker Hexagon Wrench Hand washing device Tapered pad Outlet nut Embedded cover Battery panel A INSTALLATION DIMENSIONS Unit:mm :mm Finished Wall Female Thread GF4334/A1/ BRAVAT PLUMBING INDUSTRIAL CO., Ltd. Service Hot Line

2 B Helpful Tools Impact Drill Adjustable Wrench Screwdriver Pencil Tape Measure Teflon Tape Points for attention before installation The use of AC power supply products,in the introduction to the embedded box the power cord before,must be fitted with an opening distance of 3mm and above all very disconnected devices,and cut off the power before installation to ensure the safe use of! Power line ground wire connected into the ground screw on. The installation instructions in the picture or text description, if it is real do not match, in kind prevail! C INSTALLATION STEP 18CM Note: Please pre-construction installation dimensions in accordance with the design of this product better drains and decorative wall thickness, In order to achieve a good installation results 25-30CM 30CM Supply 1.Refer to installation diagram, in the wall slot 2.Light pipes, laying good pipe, and flush pipe to ensure good quality products before the beginning of installation 10CM Power Line Knock down hole Power adapter (This step applies only to AC / DC products) knocked off the first hole embedded knock me down, and then remove the embedded cover, thento AC220V power cord thread through embedded box on the right side into box knocked off the hole, the electrical power cord access Source adapter The embedded cover back onto the wall with screws lock body wall. 2.The 32 stainless steel pipe (see user-supplied) through the Tapered pad, and through the outlet nut fixed on the embedded box outlet, make sure the seal interfaces stainless steel pipe GF4334/A1/ BRAVAT PLUMBING INDUSTRIAL CO., Ltd. Service Hot Line

3 Inlet Assemble Retaining Rubber Washer 6 with Water connector. 2.The water through the inlet Water connector 5, Round head screw 4 (Wrap the Teflon tape in the thread). Small pieces of wood or other solid materials 1.Placement of embedded box, and use small pieces of wood or other solid material level up, so cabinet stability 32 stainless steel pipe Embedded flush with the flat tile Embedded cover Porcelain Tile 1.Supplement tile, so that blank wall flush with the embedded box border, tiles cover surface flush with the embedded State: in the pipeline should be routine after installation Test the water test required to ensure the pipeline, and Interface position without any leakage Install or replace batteries 1.Remove the control panel and took out the battery box 3 2.Phillips screwdriver to open battery pack box, and then polarity into four AA alkaline batteries 14. Specify: Install the battery, new and old batteries can not be mixed Install the control panel 1.Embedded with a Phillips screwdriver under the Embedded cover 13 ; 2.The Sensor panel 1 power supply valve plug embedded respectively in the corresponding plug-in Body wall ; 3.Screw the Sensor panel 1 fixed to the Body wall on (Note installation direction) 4.Test cover panels 15, regulator valve on the manual button and the button panel fit (recommended after the glue in the regulation of fixed button) 5.The Body wall fitting groove in the Control Panel GF4334/A1/ BRAVAT PLUMBING INDUSTRIAL CO., Ltd. Service Hot Line

4 D OPERATION Infrared automatic sensor, after the flushing method: When the body close to the squatting toilet flushing device, sensor perception, left flush automatically after about 8 seconds, then turn off: (washing time set the standard factory value). Widely used in restaurants, hotels, hotels, office buildings, factories and mines, schools, places of entertainment such as public restrooms. Note: Rinse control sensor to the human body, if it lights blink continuously, tableshow the battery voltage, to remind users to change the batteries (replace batteries, please refer toinstallation steps relevant part). For the first time on the battery or replace the battery, the washing instructions for induced five times Lights flashing, at this time for the high (red light is always on). Washer flush For about 8 seconds (this function to the factory default). If the sensor material for the fast-moving object or the sensor material is not sensitive in the region, the sensor will not flush. PARAMETERS Power AA 1.5V Alkaline Batteries 4 pcs Sensing Distance Automatic adjustment30-60cm Sensing Duration 1 second Battery Life Time Appr.50,000 cycle Supply Water Pressure 1-6kgf/cm2 Ambient Teperature: 1-55 Supply Water Pipe Specification G1 Non-working Power Consumption Operating Voltage AC/DC E SIMPLE TROUBLE SHOOTING Problem Alternative Cause Solution No Flow Restricted flow 1.Water cut-off switch did not open 2.Power did not pass 3.Solenoid valve malfunction Inadequate water pressure, or because of insufficient water supply led to a shortage of water Filter block Open water cut-off switch Power on Contact maintenance personnel Contact with the water Clean the filter Long flow Other objects within the sensing region Removal of objects within the sensing region GF4334/A1/ BRAVAT PLUMBING INDUSTRIAL CO., Ltd. Service Hot Line

5 F MAINTENANCE 10 Hand wash-device 10 In the absence of induction state needs flushing, set the hand near the sensor window washer 10 Squatting toilet automatically flushthe left hand washerflush automatically shut down. Implementation can be repeated many times without induction of flushing Cut-off button Filter Strainer top NOTE: To maintain the pipe seal. Cut-off button Mobile Plug Solenoid valve Clean the filter Valve repair The following recommended cleaning filter Construction installed the first time use For more than six months; Found that decreasing the use of flow Clean the filter order: 1.Remove the panel with a suction cup, then tighten the four screws, then remove the control panel; 2.Screwdriver clockwise rotating with the word end switch, until the closure of water supply; 3.Counterclockwise with a Hexagon Wrench unscrew the filter cap; 4.Remove the filter, rinse; 5.Back in reverse steps to re-install filter. If you need to clean the electromagnetic valve repair, follow these steps for maintenance 1.Remove the panel with a suction cup, then tighten the four screws, then remove the control panel; 2.Screwdriver clockwise rotating with the word end switch, until the closure of water supply; 3.Remove the screws on the solenoid valve, remove the solenoid valve, remove the cartridge for cleaning or replacement of mobile 4.In reverse steps to re-install back valve GF4334/A1/ BRAVAT PLUMBING INDUSTRIAL CO., Ltd. Service Hot Line