150M Wireless-N Outdoor AP Router

Transcription

1 150M Wireless-N Outdoor AP Router Model No. ib-or246150n QIG Ver.: 2.0.0

2 FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment. CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

3 CONTENTS Package contents Introduction Main Features Rear panel description Port description Hardware Installation Steps Connecting the Router System Requirements TCP/IP Configuration Connect to Outdoor Router Setup Wizard Operation Mode guideline AP Router WISP Access Point AP Client Wireless Menu Network Settings System Tools Diagnostic Tools Contact Information... 21

4 Package contents The following items should be found in your package: 150M Wireless-N Outdoor AP Router (ib-or246150n) DC 12V Power Adapter POE Injector Cable Tie User Manual NOTE: Kindly use the POE Injector as provided in box packaging. Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact with your nearest dealer.

5 1. Introduction iball Baton ib-or246150n is High Power Outdoor AP Router with reliable solution. Enhanced Wireless data transmission rate up to 150Mbps. Operation Mode: AP Router, WISP, Access Point (AP) & AP Client Wireless Mode: AP, Lazy, Bridge & AP Bridge Antenna Type: Internal 12dBi Directional Antenna External SMA Connector 1.1 Main Features Complies with 2.4GHz IEEE802.11b/g & n standards. With IEEE802.3 & 802.3u standards 1-10/100M (RJ45) LAN port & 1- WAN port Broadband Internet - PPPoE, Dynamic IP & Static IP WISP - Shares wireless Internet to wired & wireless users Wireless security - WEP, WPA-PSK & WPA2-PSK DHCP Server & Client mode With Multiple SSID security Firewall features as IP/Port & MAC filtering With Virtual Server, DMZ & UPnP With Low Noise Amplifier (LNA) support Power over Ethernet (Passive PoE) Mounting provision: Pole or Wall Outdoor Unit Protection: IPX5 Standard IPX5 Standard: IPX5 is the grade at which product continues to function when directly subjected to 12.5 L of water per minute from all directions using a 6.3 mm inside diameter nozzle at a distance of approximately 3m for at least 3 minutes.

6 1.2 Rear panel description LED Indicator State Description 1. PWR LED 2. WLAN LED 3. WAN LED ACT 4. LAN LED ACT ON Off ON Off Flashing ON Off Flashing ON Off Flashing The WLAN Broadband Router is powered ON. The WLAN Broadband Router is powered Off. Wireless Radio ON. Wireless Radio Off. Data is transmitting or receiving on the wireless. Port linked. No link. Data is transmitting or receiving on the WAN interface. Port linked. No link. Data is transmitting or receiving on the LAN interface.

7 1.3 Port description Interfaces Power Reset / Antenna Switch SMA connector LAN (Right) WAN (Right) Description 12V DC Power Reset button : press for 5-10 sec & release Antenna Switch : press for 2 to 4 sec & release For external antenna. You can use the SMA connector to connect with 2.4GHz external antenna. The RJ-45 port allows LAN connection through Cat. 5 cables. Support Auto-Negotiation RJ45 ports, half/ full duplex; comply with IEEE 802.3/ 802.3u respectively. The RJ-45 port allows WAN connection through a Cat. 5 cables. Support Auto-Negotiation RJ45 ports, half/ full duplex; comply with IEEE 802.3/ 802.3u respectively.

8 1.4 Hardware installation steps Step1: Push the button in the side to remove upper housing. Step2: Pass through Ethernet cable from the hole; insert the cable to Secondary port. Note: RJ-45 8P8C Ethernet cable is required. Step3: Install the upper housing and make sure the housing is well installed.

9 Step4: Install POE Injector DC: Insert adapter POE: This hole is linked to Secondary port of the Outdoor Router with RJ-45. LAN: This hole is linked to LAN side PC/Hub or Router/ADSL modem device with RJ-45 Note: The above image is just for your reference, Colour of POE may vary as per product packaging.. 2. Connecting the Router 2.1 System Requirements Broadband Internet Access Service (DSL/Cable/Ethernet) 1 DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is connected directly to the Ethernet.) Computer with a working Ethernet Adapter and an Ethernet cable with RJ45 connector TCP/IP protocol on each pc Web browser, such as Microsoft Internet Explorer, Mozilla Firefox 2.2 TCP/IP Configuration The default IP address of the ib-or246150n 150M Wireless-N Outdoor AP Router is and the default Subnet Mask is These values can be changed as per the requirement. In this guide, we use all the default values for description. Connect the local PC to the LAN ports of the Router. The IP address for your PC can be configured in the following two ways.

10 Configure the IP address manually 1) Set up the TCP/IP protocol for your PC. 2) Configure the network parameters. The IP address is xxx ( xxx is any number from 1 to 254), Subnet Mask is and Gateway is (The Router s default IP address). Obtain an IP address automatically 1) Set up the TCP/IP Protocol in Obtain an IP address automatically mode on your PC. 2) Then the built-in DHCP server will assign IP address for the PC. Now, you can run the Ping command in the command prompt to verify the network connection between your PC and Router. 2.3 Connect to 150M Wireless-N Outdoor AP Router Open a WEB browser, i.e. Microsoft Internet Explorer 6.1 SP1 or above, then enter IP address as on the URL to connect the iball Baton ib-or246150n Broadband Router. Username: admin Password: admin

11 3. Setup Wizard 1 After you login web page, Click WISP Wizard click Scan Select SSID Enter encryption password Select specified WAN type PPPOE / DHCP / Static click Next Step Note: DHCP: If the device connects to DHCP Server of uplink or WISP, please select this mode. The device will obtain IP address from uplink DHCP server or WISP automatically. PPPoE: If WISP offer PPPOE access type, please select this mode. You should fill in both the User Name and Password that your ISP supplies Static:If WISP offer Static IP access, please select this mode and enter IP address/subnet Mask/Gateway and DNS server IP address

12 2 LAN Settings: You could change Gateway IP adress here or keep defaults,then click Next 3 DHCP Server Settings: You can enable or disable DHCP server here,then click Next 4 Wireless Settings: To configure wireless settings of the device, you could enable or disable wireless, select security mode / set encrypt key etc,after that click Apply to save previous settings.

13 Note: The device will restart after changing these settings, if you just keep defaults value please click next for further process 4. Operation Mode guideline 4.1) AP Router: Click Operation Mode AP Router go to basic configuration page, as below image: Note: AP Router mode is SOHO router function, Router connect to wired ISP to access internet DHCP: When the Device connects to a DHCP server, or ISP support DHCP service, please choose this type. The Device will get the IP address automatically from the DHCP server or the WISP. Once the connection started successfully, you can access internet.

14 PPPoE: If your wireless ISPs supports PPPoE, you should choose this type. In this condition, you should fill both the User Name and Password that your ISP provides. Static IP:In this type, you should manually fill in the IP address, Subnet Mask, Default Gateway, and DNS IP address, which are specified by your ISP. The Sixth Step: Connection status After you finished related configuration, and you wish to check if settings is succeed or not, please go to Status page for more details. 4.2 WISP: Please refer to Setup Wizard for details 4.3 Access Point Check Operation Mode Access Point(AP), you ll see in below image. In this page you may set wireless access point as per your requirement, after that click Apply to save settings and restart device. Select one you wish to enable its SSID, click Enable. Once you enable BSSID, you could select one Channel and configure specified wireless parameter based the BSSID, also you could enable multiple SSID option.

15 Once enable SSID CPE will broadcast its name. Select SSID blank you can change its name here. Broadcast SSID: Enable the option, SSID will be visible you can see the BSSID name by PC or laptop s wireless scan tools, once you disable it user couldn t find the SSID by scanning tools, the SSID has been hided, but if you still wish to connect with the SSID, just enter the SSID manually. Security Mode: In this option you can configure encryption mode, key etc security mode currently support Open WEP, WPA-PSK, WPA2-PSK. Security Type: Suggest security type to be TKIP mode which is better encryption type. 4.4 AP Client: In this mode, the device associate with nearby AP and checks the network device combination as required. The access point then forms a wireless bridge between the wired LAN and clients through the device. CPE broadcasting its SSID, client devices obtain IP address from uplink hotspot or WISP. Connects to wireless AP or WLAN base station Check Operation Mode select AP Client click Scan select specified SSID you wish to connect with, then fill-in password Click Apply to save settings Channel without setting, since Channel of the CPE will automatically consistent with the front end WLAN base station in AP and AP Client mode.

16 CPE will disable its DHCP server in AP Client mode, for management you can assign different IP address for each CPE Note: If there is no targeted SSID in checking list, you d better have some more Scan process. but if still nothing in checking list, double check if the frequency of WLAN s working channel beyond your CPE s scope. e.g CPE only support 13 channel, but WLAN base station just working on channel Wireless Menu Click Wireless to go Wireless setting menu, as shown in below image. Mode: To select proper mode of wireless, like b/g/n etc. Channel: To setup right wireless channel number for the device. SSID: Identification of device s wireless network. Security Mode: Security type of main SSID, in drop-down list to choose right mode you need or disable it. Different types of security mode is : WEP, WAP-PSK & WPA2-PSK

17 6. Network Settings Click Network Settings to configure Internet as provided, as shown in below image. WAN Connection Type: Allows different way to access Internet. Static IP: Use a Fixed IP Address to access ISP, in this mode user need to enter fixed IP vvvvvvvvvvaddress, gateway etc manually. DHCP: In this mode, device will obtained dynamic IP address and other network parameters from ISP. PPPoE: In this mode, the device access ISP by PPPoE dial-up, PPPoE is used usually ADSL broadband access.. IP/Subnet mask/gateway/domain Server: Visible in static WAN connection type, manually assign IP Address, Gateway information etc..

18 7. System Tools Click System Tools to go to system management menu, as shown in below image. Password Settings: To set system administrator and password here. Time Settings: To set time zone and time information here. Backup & Restore: You can backup your existing configuration file to your system & afterwards you can restore the settings as required. Factory Defaults: Restore Router to factory default mode. Restart: Restart the Router for applied settings. Remote Access: You can manage the Router remotely. Firmware Upgrade: To upgrade Router s new firmware. Reset: To restore CPE to factory defaults either through Reset button on router by pressing reset button for 5-10 seconds or click Reset button on web page. 8. Diagnostic Tools You could check all the system logs on Log Settings

19 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. iball Baton is a registered trademark of Best IT World India Pvt. Ltd. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from Best IT World India Pvt. Ltd. All rights reserved.