Exhaust System. Table of Contents. Section 6C - Measuring Exhaust Elbow Height
|
|
|
- Belinda Hunt
- 7 years ago
- Views:
Transcription
1 Exhust System Mesuring Exhust Elow Height Tle of Contents Setion 6C - Mesuring Exhust Elow Height Mesuring Exhust Elow Height...6C-2 Generl Informtion...6C-2 Bot Requirements...6C-4 Loding Requirements...6C-5 Loding the Bot with Cpity Plte...6C-5 Loding the Bot Without Cpity Plte...6C-7 Cler Hose Mesurement Method...6C-10 Cler Hose Mesurement Method from Seok or Muffler Drin...6C-11 Mesurement Method without Seok or Muffler Drin...6C-14 6 C APRIL 2008 Pge 6C-1
2 Mesuring Exhust Elow Height Mesuring Exhust Elow Height Generl Informtion The height of the exhust elows must e within the dimensions speified to prevent wter intrusion prolems. Instll exhust elow risers, if needed, to otin the proper exhust elow height nd exhust ngle. Risers re limited to mm (8 in.) on ll 8.1 models with emissions ontrol nd without emissions ontrol. Risers re limited to mm (6 in.) on ll 5.7 nd 6.2 models without emissions ontrol. Risers re limited to mm (8 in.) on emissions ontrolled 5.7 L models. Tke mesurements with the ot in the wter nd loded s outlined to simulte the mximum loding onditions likely to e enountered in norml opertion. IMPORTANT: Mesure exhust elow height to the wterline inside of the wter lift muffler (insted of the wter line outside of the ot) on pplitions so equipped. Refer to Wter Lift Muffler. IMPORTANT: Lod distriution reommendtions re the responsiility of the ot mnufturer. Any lod distriution onditions tht will ffet the exhust system must e lerly ommunited to the opertor in the owner's mnul. For exmple, the numer of people tht n e loted on the swim pltform simultneously should e inluded in the mnul, if this ould pose prolem. Mesurements under ll loding onditions must e within the following speifitions. Minimum Exhust Elow Height Model Inord nd V drive Tow Sports models Tow Sports inline models Speifition 38 m (15 in.) 33 m (13 in.) Minimum Exhust Hose Slope Model All models Speifition Within 457 mm (18 in.) of engine Reminder of system (if pplile) 10 3 If the exhust elow height or exhust ngle is insuffiient, modify the exhust system or instll the pproprite exhust riser. Refer to the Merury Preision Prts nd Aessory Guide for prt numers. The mximum exhust riser height is speified in the tle elow. Riser Options without Emissions Control Model Low Medium High All 5.7 nd 6.2 models 43 mm (1.7 in.) 76 mm (3 in.) nd 119 mm (4.7 in.) 152 mm (6 in.) 8.1 H.O. nd Horizon mm (2 in.) 152 mm (6 in.) 203 mm (8 in.) Riser Options with Emissons Control Model Low Medium High All models 51 mm (2 in.) 102 mm (4 in.) 152 mm (6 in.) 203 mm (8 in.) Pge 6C APRIL 2008
3 EXHAUST ANGLE MEASUREMENT WITHOUT EMISSIONS CONTROL Mesuring Exhust Elow Height Mesure the exhust ngle of eh setion of the exhust system using n inlinometer s shown in the digrm elow. Begin the mesurement t the exhust elow outlet ontinuing long eh setion to the exhust exit point of the ot. Perform ll exhust ngle mesurements with the ot t rest in the wter. Perform the first set of mesurements without lod in the ot. Perform the seond set of mesurements with the ot fully loded. See Loding Requirements. IMPORTANT: Ensure tht the exhust hose or tue hs minimum of 3º of slope fter the first 18 in Typil 8.1 exhust - Inlinometer - Exhust hose or tue - Minimum 457 mm (18 in.) Typil 8.1 exhust - Inlinometer - Exhust hose or tue - Minimum 457 mm (18 in.) APRIL 2008 Pge 6C-3
4 Mesuring Exhust Elow Height EXHAUST ANGLE MEASUREMENT WITH EMISSIONS CONTROL Mesure the exhust ngle of eh setion of the exhust system using n inlinometer s shown in the digrm elow. Begin the mesurement t the exhust elow outlet ontinuing long eh setion to the exhust exit point of the ot. Perform ll exhust ngle mesurements with the ot t rest in the wter. Perform the first set of mesurements without lod in the ot. Perform the seond set of mesurements with the ot fully loded. See Loding Requirements. IMPORTANT: Ensure tht the exhust hose or tue hs minimum of 3º of slope. Typil exhust - Minimum 457 mm (18 in.) - Inlinometer - Exhust hose or tue Bot Requirements IMPORTANT: Consider the following requirements efore performing the exhust elow wterline height mesurement. No prototype hulls or light lyup hulls should e onsidered. Any mesurement performed on non prodution ots, prototype hulls, or light lyup hulls ould e inurte nd ould result in produt dmge. All ots tht disply CE ertifition pity plte must use the mximum pity s stted on the CE ertifition pity plte to perform the exhust elow wterline mesurement. All ots tht only disply the US Cost Gurd (USCG) pity plte must use the mximum pity s stted on the USCG pity plte to perform the exhust elow wterline mesurement. For ots tht do not hve pity plte, the mximum pity lod is the numer of persons tht n sit on designted seting plus rgo exluding in spe. Mesurements used for offiil Merury MerCruiser udit t the OEM ot uilder must e performed on urrent prodution ots. No prototype hulls or light lyup hulls will e onsidered for offiil udit purposes. Mesurements used for offiil Merury MerCruiser udit t OEM ot uilders must use the CE ertifition mximum lod for ny ot model tht will e sold outside of the United Sttes. Pge 6C APRIL 2008
5 Loding Requirements Mesuring Exhust Elow Height 1. Fill the fuel tnks, fresh wter tnks or holding tnks, llst tnks, nd heter tnks to simulte fully loded ondition. 2. Weights n e used to simulte these lod onditions if desired. Ple weights in the orresponding re for whih the lod is eing repled. Refer to the following onversions. 1 U.S. gllon of wter = 8.3 l. 1 liter of wter = 1 kg 1 U.S. gllon of gsoline = 6 l. 1 liter of gsoline = 0.72 kg 3. For the purpose of MerCruiser wterline height mesurements: One person is equivlent to kg (165 l.) Crgo per person is equivlent to kg (25 l.) 4. Add weight for ny dditionl ot options: extr ttery, ttery hrger, tower, rh, genertor, llst tnks, llst sks, television, rpet, nhor, stereo/entertinment equipment, wsher/dryer, sfe, et. 5. If swim pltform is n option, the swim pltform must e instlled for the wterline height mesurement. Use the following guide to determine the orret swim pltform lod:. Bots less thn 8.84 m (29 ft.) long, not inluding ots tht re 8.84 m (29 ft.) long, must dd the mximum rted swim pltform weight pity to the swim pltform.. Bots less thn 8.84 m (29 ft.) long, not inluding ots tht re 8.84 m (29 ft.) long tht do not hve mximum rted swim pltform weight pity, must dd Kg (400 l.) to the swim pltform.. Bots 8.84 m (29 ft.) long nd greter thn 8.84 m (29 ft.) long, must dd the mximum rted swim pltform weight pity to the swim pltform. d. Bots 8.84 m (29 ft.) long nd greter thn 8.84 m (29 ft.) long, tht do not hve mximum rted swim pltform weight pity must dd kg (500 l.) to the swim pltform. Loding the Bot with Cpity Plte For ots with pity plte, use the mximum lod for persons nd ger s listed on the pity plte to determine the numer of persons to ple onto the ot for exhust elow wterline height mesurements. IMPORTANT: Use 20 inhes for verge pssenger set width when mesuring enh seting. Round up or down t 0.5 to otin whole person. See the exmples listed elow. 48 in. (enh set length) 20 in. (set width) = 2.4 persons. 2.4 persons rounded down = 2 persons. 55 in. (enh set length) 20 in. (set width) = 2.75 persons persons rounded up = 3 persons. 1. Tke the mximum pity weight s listed on the pity plte (XXXX l. Persons, Ger) nd sutrt the swim pltform lod, if pplile. 2. Next divide the weight y kg (165 l.) per person. This gives the whole numer nd reminder of kg (165 l.) persons to lod onto the ot APRIL 2008 Pge 6C-5
6 Mesuring Exhust Elow Height 3. Put the reminder of person in the next ville set. See Bot loding digrm. CE Cpity Plte USCG Cpity Plte IMPORTANT: If there is not enough seting for the numer of people, tret the leftover weight s rgo. Lod rgo weight onto the ot efore loding pssenger weight. 4. If pplile, lod rgo (leftover persons weight) onto the ot. Distriute rgo s desried elow. IMPORTANT: If the ot onfigurtion does not llow for ft, enter, nd ow storge, hoose the storge pplition from the Optionl Crgo Distriution tle tht est pplies to your ot onfigurtion. Preferred Crgo Distriution Aft storge Center storge Bow storge 25% 50% 25% EXAMPLE Optionl Crgo Distriution Aft storge Center storge Bow storge 25% 75% None None 75% 25% 50% None 50% None 100% None 100% None None None None 100% 5. Perform the first mesurement with the swim pltform loded nd the person tking the wterline mesurement on the ot. 6. Lod the swim pltform if equipped. 7. Mesure the exhust elow wterline height. IMPORTANT: View ll ot seting s rows tht re prllel to the trnsom of the ot. 8. Lod person weight into set, nd mesure the exhust elow wterline height fter eh person weight is loded onto the ot. Repet until person weight is is loded into eh set in tht row. 9. Continue the proess moving forwrd towrd the ow of the ot to the next row of sets until person weight is loded into eh set. NOTE: The totl weight loded onto the ot must not exeed the mximum pity displyed on the pity plte. NOTE: The following exmple is provided s referene. NOTE: This exmple uses ot tht is less thn 8.84 m (29 ft.) long, not inluding ot tht is 8.84 m (29 ft.) long tht does not hve mximum rted swim pltform weight pity, nd must dd Kg (400 l.) to the swim pltform Pge 6C APRIL 2008
7 Mesuring Exhust Elow Height NOTE: Use 0.50 l. s the rek point to round up or down to otin whole pound. 1. Mximum lod (persons nd ger) from pity plte swim pltform lod = remining weight to e pled in the ot l. 400 l. = 700 l. 2. Remining weight to e pled in the ot MerCruiser person weight = numer of persons to lod onto the ot 700 l. 165 l. = 4.24 persons 3. Totl numer of persons numer of whole persons = remining persons 4.24 persons 4 persons = 0.24 remining persons 4. Reminder persons MerCruiser person weight = reminder MerCruiser person weight l. = 40 l. IMPORTANT: View ll ot seting s rows tht re prllel to the trnsom of the ot. 5. Using the totls in this exmple, lod four 165 l. persons nd one 40 l. person onto ot seting with 400 l. on the swim pltform. 400 l l. = 565 l. 565 l l. = 730 l. 730 l l. = 895 l. 895 l l. = 1060 l l l. = 1100 l. d e f Bot loding digrm - Swim pltform lod - MerCruiser person weight (one) - MerCruiser person weight (two) d - MerCruiser person weight (three) e - MerCruiser person weight (four) f - Reminder MerCruiser person weight (five) Loding the Bot Without Cpity Plte For ots tht do not disply pity plte, the numer of persons to e loded onto the ot for mesuring purposes is the numer of persons tht n sit on designted seting exluding in spe. An dditionl weight of 25 l. per person is to e dded to the ot efore loding pssenger weight onto the ot. IMPORTANT: Use 20 inhes for verge pssenger set width when mesuring enh seting. Round up or down t 0.5 to otin whole person. See the exmples elow. 48 in. (enh set length) 20 in. (set width) = 2.4 persons. 2.4 persons rounded down = 2 persons APRIL 2008 Pge 6C-7
8 Mesuring Exhust Elow Height 55 in. (enh set length) 20 in. (set width) = 2.75 persons persons rounded up = 3 persons. 1. Totl numer of persons tht n sit on designted seting exluding in spe MerCruiser person weight = mximum pssenger lod for mesurement. Numer of persons 165 l. (MerCruiser person weight) = XXXX l. mximum pssenger lod. 2. Mximum pssenger lod from the lultion ove swim pltform lod if pplile. 3. Divide the weight y 165 l. per person. This gives the numer of 165 l. persons to lod onto the ot. Round up to next whole numer. See Exmple 3. IMPORTANT: To ount for rgo, dd weight of 25 l. per person to the ot efore loding pssenger weight onto the ot. 4. Clulte the rgo y multiplying 25 l. y the numer of persons tht n sit on designted seting exluding in spe. See Exmple. 5. Lod the rgo onto the ot. Distriute rgo s desried elow. IMPORTANT: If the ot onfigurtion does not llow for ft, enter, nd ow storge, hoose the storge pplition from the Optionl Crgo Distriution tle tht est pplies to your ot onfigurtion. Preferred Crgo Distriution Aft storge Center storge Bow storge 25% 50% 25% Optionl Crgo Distriution Aft storge Center storge Bow storge 25% 75% None None 75% 25% 50% None 50% None 100% None 100% None None None None 100% EXAMPLE 6. Perform the first mesurement with the swim pltform loded nd the person mesuring the wterline on the ot. 7. Lod the swim pltform if equipped. 8. Mesure the exhust elow wterline height. IMPORTANT: View ll ot seting s rows tht re prllel to the trnsom of the ot. 9. Lod person weight into set, nd mesure the exhust elow wterline height fter eh person weight is loded onto the ot. Repet until person weight is is loded into eh set in tht row. 10. Continue the proess moving forwrd towrd the ow of the ot to the next row of sets until person weight is loded into eh set. NOTE: The following exmple is provided s referene. This exmple uses ot tht is 8.84 m (29 ft.) long nd greter thn 8.84 m (29 ft.) long, tht does not hve mximum rted swim pltform weight pity, nd must dd Kg (500 l.) to the swim pltform. Pge 6C APRIL 2008
9 Mesuring Exhust Elow Height IMPORTANT: The Designted Seting Digrm following illustrtes the numer of pssengers tht n sit on designted seting exluding in spe Designted Seting Digrm This exmple uses 9 persons s the mximum pssenger lod. NOTE: Use 0.50 l. s the rek point to round up or down to otin whole pound. 1. To determine the mximum rgo lod multiply the mximum pssenger lod y the mximum rgo weight per pssenger. 9 pssengers 25 l. = 225 l. 2. To determine the preferred rgo distriution for ft, enter, nd ow storge:. To determine the mximum ft storge rgo weight, multiply the mximum rgo weight y 25% 3. To determine the mximum enter storge rgo weight, multiply the mximum rgo weight y 50%. 225 l. 50% = l l. rounded up = 113 l. 4. To determine the mximum ow storge rgo weight, multiply the mximum rgo weight y 25% 225 l. 25% = l l. rounded down = 56 l. 5. To determine the mximum numer of pssengers to lod onto the ot, multiply 9 pssengers y 165 l. (MerCruiser person weight) to get 1485 l. (totl pssenger lod) 9 pssengers 165 l. = 1485 l. 6. Sutrt the swim pltform lod from the totl pssenger lod to get the remining weight to e pled in the ot l. 500 l. = 985 l. 7. Divide the remining weight to e pled onto the ot y the MerCruiser person weight to get the mximum numer of pssengers to lod onto the ot. 985 l. 165 l. = 5.9 pssengers 5.90 pssengers rounded up = 6 pssengers 8. Using the totls in this exmple lod 56 l. rgo in the ft storge, 113 l. rgo in the enter storge, nd 56 l. rgo in the ow storge onto the ot efore dding pssenger weight. Then, lod six 165 l. pssengers, onto the ot with 500 l. on the swim pltform. 500 l l. = 725 l. 725 l l. = 890 l. 890 l l. = 1055 l APRIL 2008 Pge 6C-9
10 Mesuring Exhust Elow Height 1055 l l. = 1220 l l l. = 1385 l l l. = 1550 l l l. = 1715 l. g d h e f i j Cler Hose Mesurement Method Crgo, swim pltform, nd pssenger weight loding digrm - Swim pltform lod - MerCruiser person weight (one) - MerCruiser person weight (two) d - MerCruiser person weight (three) e - MerCruiser person weight (four) f - MerCruiser person weight (five) g - MerCruiser person weight (six) h - Aft storge i - Center storge j - Bow storge 1. Otin n 8 10 mm (5/16 3/8 in.) ID (inner dimeter) ler hose pproximtely 4.5 m (15 ft.) long. Instll metl fitting or weight on one end of the hose to keep tht end of the hose elow the wterline. The fitting or weight must not restrit wter from filling the ler hose Cler hose - Fitting - Unrestrited opening IMPORTANT: On engines equipped with more thn one exhust elow, perform the exhust elow wterline height mesurement on the side tht sits lowest in the wter. 2. Put the weighted end of the ler hose over the side of the ot tht is sitting lowest in the wter. 3. Sumerge the ler hose until ompletely filled with wter. 4. Ple finger over the open end of the ler hose efore removing it from the wter. Pge 6C APRIL 2008
11 Mesuring Exhust Elow Height 5. Coil the exess ler hose into the ottom of the ot ilge. Keep the oil of ler hose elow the wterline. 6. Keeping the ler hose in line with the engine's exhust elow, lift the end of the ler hose up to the highest point of the exhust elow. 7. Slowly tke the finger off of the end of the ler hose to let the wter level stilize. The wter will seek the level of the wter outside of the ot. Keep the ler hose lose to the exhust elow nd s vertil s possile. e d Produts without emissions ontrol - Wterline d - Weight - Top of exhust elow e - Wterline to top of exhust elow mesurement - Cler hose d e Produts with emissions ontrol - Wterline d - Wterline to top of exhust elow mesurement - Cler hose e - Weight - Top of exhust elow Cler Hose Mesurement Method from Seok or Muffler Drin IMPORTANT: Mesure the exhust elow height to the wterline inside of the wter lift muffler (insted of the wter line outside of the ot) on pplitions so equipped APRIL 2008 Pge 6C-11
12 Mesuring Exhust Elow Height IMPORTANT: The engine must hve een operted previously to fill the muffler with wter. IMPORTANT: On engines equipped with more thn one exhust elow, perform the exhust elow wterline height mesurement on the side tht sits lower in the wter. 1. Atth ler hose to the muffler drin point or seok drin point. 2. Strt the engine to fill the muffler nd hose. 3. If tthed to the seok drin, open the seok. 4. Route the reminder of the hose towrd the engine's exhust mnifold nd elow. Ensure tht this open end setion of the hose is s vertil s possile from the ot's ilge to the top of the exhust elow. 5. Coil exess hose in the ilge of the ot, keeping it elow the wter line. 6. Lower the open end of the hose nd siphon wter until it strts to ome out of the hose. Put finger over the hose nd lift open end until it is t the top of the exhust elow. 7. Slowly tke the finger off of the end of the hose to let the wter level stilize. The wter will seek the level of the wter outside the ot. Keep the hose lose to the exhust elow nd s vertil s possile. 8. The mesurement etween the wter in the hose nd the top of the exhust elow is the exhust elow height. The mximum riser height is 20.3 m (8 in.) on 8.1 H.O. nd Horizon 8.1 models with nd without emissions ontrol. Riser height is limited to 15.2 m (6 in.) on ll 5.7 nd 6.2 models without emissions ontrol nd 20.3 m (8 in.) on ll 5.7 models with emissions ontrol. NOTE: Mesure the wter line inside the muffler when the drin plug is not ville. PRODUCTS WITHOUT EMISSIONS CONTROL Typil vertil wter lift muffler - Minimum exhust elow height with mximum lod - Cler hose for mesuring wterline Pge 6C APRIL 2008
13 Mesuring Exhust Elow Height PRODUCTS WITH EMISSIONS CONTROL Typil horizontl wter lift muffler - Minimum exhust elow height with mximum lod - Cler hose for mesuring wterline Typil horizontl wter lift muffler - Cler hose for mesuring wterline - Minimum exhust elow height with mximum lod APRIL 2008 Pge 6C-13
14 Mesuring Exhust Elow Height Typil vertil wter lift muffler - Cler hose for mesuring wterline - Minimum exhust elow height with mximum lod Mesurement Method without Seok or Muffler Drin IMPORTANT: Mesure the exhust elow height to the wterline inside of the wter lift muffler (insted of the wter line outside of the ot) on pplitions so equipped. IMPORTANT: The engine must hve een operted previously to fill the muffler with wter. IMPORTANT: On engines equipped with more thn one exhust elow, perform the exhust elow wterline height mesurement on the side tht sits lowest in the wter. 1. Remove the the dishrge hose from the wterlift muffler. 2. Mesure the wter level inside the muffler. 3. Mrk the outside of the muffler to show the wter line height inside the muffler. 4. Using n pproprite tool mesure the distne from the muffler wterline to the top of the exhust elow to determine the exhust elow height. Pge 6C APRIL 2008
Calculating Principal Strains using a Rectangular Strain Gage Rosette
Clulting Prinipl Strins using Retngulr Strin Gge Rosette Strin gge rosettes re used often in engineering prtie to determine strin sttes t speifi points on struture. Figure illustrtes three ommonly used
INSTALLATION, OPERATION & MAINTENANCE
DIESEL PROTECTION SYSTEMS Exhust Temperture Vlves (Mehnil) INSTALLATION, OPERATION & MAINTENANCE Vlve Numer TSZ-135 TSZ-150 TSZ-200 TSZ-275 TSZ-392 DESCRIPTION Non-eletril temperture vlves mnuftured in
1. Definition, Basic concepts, Types 2. Addition and Subtraction of Matrices 3. Scalar Multiplication 4. Assignment and answer key 5.
. Definition, Bsi onepts, Types. Addition nd Sutrtion of Mtries. Slr Multiplition. Assignment nd nswer key. Mtrix Multiplition. Assignment nd nswer key. Determinnt x x (digonl, minors, properties) summry
The remaining two sides of the right triangle are called the legs of the right triangle.
10 MODULE 6. RADICAL EXPRESSIONS 6 Pythgoren Theorem The Pythgoren Theorem An ngle tht mesures 90 degrees is lled right ngle. If one of the ngles of tringle is right ngle, then the tringle is lled right
Practice Test 2. a. 12 kn b. 17 kn c. 13 kn d. 5.0 kn e. 49 kn
Prtie Test 2 1. A highwy urve hs rdius of 0.14 km nd is unnked. A r weighing 12 kn goes round the urve t speed of 24 m/s without slipping. Wht is the mgnitude of the horizontl fore of the rod on the r?
McAfee Network Security Platform
XC-240 Lod Blner Appline Quik Strt Guide Revision D MAfee Network Seurity Pltform This quik strt guide explins how to quikly set up nd tivte your MAfee Network Seurity Pltform XC-240 Lod Blner. The SFP+
FUEL SYSTEMS ROCHESTER 4 BARREL CARBURETOR 5 C
FUEL SYSTEMS 72085 ROCHESTER 4 BARREL CARBURETOR 5 C Tle of Contents Pge Rohester 4 Brrel Cruretor............. 5C-1 Torque Speifitions.................. 5C-1 Tools................................. 5C-1
SECTION 7-2 Law of Cosines
516 7 Additionl Topis in Trigonometry h d sin s () tn h h d 50. Surveying. The lyout in the figure t right is used to determine n inessile height h when seline d in plne perpendiulr to h n e estlished
SE3BB4: Software Design III Concurrent System Design. Sample Solutions to Assignment 1
SE3BB4: Softwre Design III Conurrent System Design Winter 2011 Smple Solutions to Assignment 1 Eh question is worth 10pts. Totl of this ssignment is 70pts. Eh ssignment is worth 9%. If you think your solution
Chapter. Contents: A Constructing decimal numbers
Chpter 9 Deimls Contents: A Construting deiml numers B Representing deiml numers C Deiml urreny D Using numer line E Ordering deimls F Rounding deiml numers G Converting deimls to frtions H Converting
FUEL SYSTEMS MERCARB 2 BARREL CARBURETOR 5 B
FUEL SYSTEMS 72681 MERCARB 2 BARREL CARBURETOR 5 B Tle of Contents Pge MerCr 2 BBL Cruretor.............. 5B-1 Torque Specifictions................ 5B-1 Tools............................... 5B-1 Specifictions.......................
Module 5. Three-phase AC Circuits. Version 2 EE IIT, Kharagpur
Module 5 Three-hse A iruits Version EE IIT, Khrgur esson 8 Three-hse Blned Suly Version EE IIT, Khrgur In the module, ontining six lessons (-7), the study of iruits, onsisting of the liner elements resistne,
Student Access to Virtual Desktops from personally owned Windows computers
Student Aess to Virtul Desktops from personlly owned Windows omputers Mdison College is plesed to nnoune the ility for students to ess nd use virtul desktops, vi Mdison College wireless, from personlly
Ratio and Proportion
Rtio nd Proportion Rtio: The onept of rtio ours frequently nd in wide vriety of wys For exmple: A newspper reports tht the rtio of Repulins to Demorts on ertin Congressionl ommittee is 3 to The student/fulty
Answer, Key Homework 10 David McIntyre 1
Answer, Key Homework 10 Dvid McIntyre 1 This print-out should hve 22 questions, check tht it is complete. Multiple-choice questions my continue on the next column or pge: find ll choices efore mking your
Active Directory Service
In order to lern whih questions hve een nswered orretly: 1. Print these pges. 2. Answer the questions. 3. Send this ssessment with the nswers vi:. FAX to (212) 967-3498. Or. Mil the nswers to the following
SOLVING EQUATIONS BY FACTORING
316 (5-60) Chpter 5 Exponents nd Polynomils 5.9 SOLVING EQUATIONS BY FACTORING In this setion The Zero Ftor Property Applitions helpful hint Note tht the zero ftor property is our seond exmple of getting
LISTENING COMPREHENSION
PORG, přijímí zkoušky 2015 Angličtin B Reg. číslo: Inluded prts: Points (per prt) Points (totl) 1) Listening omprehension 2) Reding 3) Use of English 4) Writing 1 5) Writing 2 There re no extr nswersheets
Welch Allyn CardioPerfect Workstation Installation Guide
Welch Allyn CrdioPerfect Worksttion Instlltion Guide INSTALLING CARDIOPERFECT WORKSTATION SOFTWARE & ACCESSORIES ON A SINGLE PC For softwre version 1.6.5 or lter For network instlltion, plese refer to
KEY SKILLS INFORMATION TECHNOLOGY Level 3. Question Paper. 29 January 9 February 2001
KEY SKILLS INFORMATION TECHNOLOGY Level 3 Question Pper 29 Jnury 9 Ferury 2001 WHAT YOU NEED This Question Pper An Answer Booklet Aess to omputer, softwre nd printer You my use ilingul ditionry Do NOT
UNIVERSITY AND WORK-STUDY EMPLOYERS WEBSITE USER S GUIDE
UNIVERSITY AND WORK-STUDY EMPLOYERS WEBSITE USER S GUIDE Tble of Contents 1 Home Pge 1 2 Pge 2 3 Your Control Pnel 3 4 Add New Job (Three-Step Form) 4-6 5 Mnging Job Postings (Mnge Job Pge) 7-8 6 Additionl
Introductory Information. Setup Guide. Introduction. Space Required for Installation. Overview of Setup. The Manuals Supplied with This Printer ENG
Introdutory Informtion Introdution Setup Guide ENG Red this mnul efore ttempting to operte the printer. Keep this mnul in hndy lotion for future referene. Overview of Setup These re the steps in printer
VMware Horizon FLEX Administration Guide
VMwre Horizon FLEX Administrtion Guide Horizon FLEX 1.0 This doument supports the version of eh produt listed nd supports ll susequent versions until the doument is repled y new edition. To hek for more
7 mm Diameter Miniature Cermet Trimmer
7 mm Dimeter Miniture Cermet Trimmer A dust seled plsti se proteting qulity ermet trk gurntees high performne nd proven reliility. Adjustments re mde esier y the ler sle redings. is idelly suited to ll
Trowel Notch Sizes for Installation of Floor Coverings, Wood Flooring and Tiles
TKB-Tehnil Briefing Note 6 Trowel Noth s for Instlltion of Floor Coverings, Wood Flooring nd Tiles Version: My 2007 Prepred y the Tehnishe Kommission Buklestoffe (TKB) (Tehnil Commission on Constrution
Start Here. Quick Setup Guide. the machine and check the components. NOTE Not all models are available in all countries.
Quik Setup Guide Strt Here HL-3140CW / HL-3150CDN HL-3150CDW / HL-3170CDW Thnk you for hoosing Brother, your support is importnt to us nd we vlue your usiness. Your Brother produt is engineered nd mnuftured
European Convention on Social and Medical Assistance
Europen Convention on Soil nd Medil Assistne Pris, 11.XII.1953 Europen Trety Series - No. 14 The governments signtory hereto, eing memers of the Counil of Europe, Considering tht the im of the Counil of
the machine and check the components Black Yellow Cyan Magenta Starter Ink Cartridges Product Registration Sheet (USA only)
Quik Setup Guide Strt Here DCP-J140W Thnk you for hoosing Brother, your support is importnt to us nd we vlue your usiness. Your Brother produt is engineered nd mnuftured to the highest stndrds to deliver
9.3. The Scalar Product. Introduction. Prerequisites. Learning Outcomes
The Sclr Product 9.3 Introduction There re two kinds of multipliction involving vectors. The first is known s the sclr product or dot product. This is so-clled becuse when the sclr product of two vectors
How To Organize A Meeting On Gotomeeting
NOTES ON ORGANIZING AND SCHEDULING MEETINGS Individul GoToMeeting orgnizers my hold meetings for up to 15 ttendees. GoToMeeting Corporte orgnizers my hold meetings for up to 25 ttendees. GoToMeeting orgnizers
Start Here. IMPORTANT: To ensure that the software is installed correctly, do not connect the USB cable until step 17. Remove tape and cardboard
Strt Here 1 IMPORTANT: To ensure tht the softwre is instlled correctly, do not connect the USB cle until step 17. Follow the steps in order. If you hve prolems during setup, see Trouleshooting in the lst
, and the number of electrons is -19. e e 1.60 10 C. The negatively charged electrons move in the direction opposite to the conventional current flow.
Prolem 1. f current of 80.0 ma exists in metl wire, how mny electrons flow pst given cross section of the wire in 10.0 min? Sketch the directions of the current nd the electrons motion. Solution: The chrge
Start Here. Quick Setup Guide. the machine and check the components DCP-9020CDW
Quik Setup Guide Strt Here DCP-9020CDW Plese red the Produt Sfety Guide first, then red this Quik Setup Guide for the orret setup nd instlltion proedure. To view the Quik Setup Guide in other lnguges,
Solenoid Operated Proportional Directional Control Valve (with Pressure Compensation, Multiple Valve Series)
Solenoid Operted Proportionl Directionl Control Vlve (with Pressure Compenstion, Multiple Vlve Series) Hydrulic circuit (Exmple) v Fetures hese stcking type control vlves show pressure compensted type
OUTLINE SYSTEM-ON-CHIP DESIGN. GETTING STARTED WITH VHDL August 31, 2015 GAJSKI S Y-CHART (1983) TOP-DOWN DESIGN (1)
August 31, 2015 GETTING STARTED WITH VHDL 2 Top-down design VHDL history Min elements of VHDL Entities nd rhitetures Signls nd proesses Dt types Configurtions Simultor sis The testenh onept OUTLINE 3 GAJSKI
End of term: TEST A. Year 4. Name Class Date. Complete the missing numbers in the sequences below.
End of term: TEST A You will need penil nd ruler. Yer Nme Clss Dte Complete the missing numers in the sequenes elow. 8 30 3 28 2 9 25 00 75 25 2 Put irle round ll of the following shpes whih hve 3 shded.
VMware Horizon FLEX Administration Guide
VMwre Horizon FLEX Administrtion Guide Horizon FLEX 1.1 This doument supports the version of eh produt listed nd supports ll susequent versions until the doument is repled y new edition. To hek for more
MATH PLACEMENT REVIEW GUIDE
MATH PLACEMENT REVIEW GUIDE This guie is intene s fous for your review efore tking the plement test. The questions presente here my not e on the plement test. Although si skills lultor is provie for your
Homework 3 Solutions
CS 341: Foundtions of Computer Science II Prof. Mrvin Nkym Homework 3 Solutions 1. Give NFAs with the specified numer of sttes recognizing ech of the following lnguges. In ll cses, the lphet is Σ = {,1}.
Enterprise Digital Signage Create a New Sign
Enterprise Digitl Signge Crete New Sign Intended Audiene: Content dministrtors of Enterprise Digitl Signge inluding stff with remote ess to sign.pitt.edu nd the Content Mnger softwre pplition for their
the machine and check the components Starter Ink Cartridges Basic User s Guide Product Safety Guide Telephone Line Cord
Quik Setup Guide Strt Here MFC-J450DW MFC-J470DW Thnk you for hoosing Brother, your support is importnt to us nd we vlue your usiness. Your Brother produt is engineered nd mnuftured to the highest stndrds
Lesson 2.1 Inductive Reasoning
Lesson.1 Inutive Resoning Nme Perio Dte For Eerises 1 7, use inutive resoning to fin the net two terms in eh sequene. 1. 4, 8, 1, 16,,. 400, 00, 100, 0,,,. 1 8, 7, 1, 4,, 4.,,, 1, 1, 0,,. 60, 180, 10,
Before you can use the machine, please read this Quick Setup Guide for the correct setup and installation.
Quik Setup Guide Strt Here DCP-365CN DCP-373CW DCP-375CW DCP-377CW Before you n use the mhine, plese red this Quik Setup Guide for the orret setup nd instlltion. WARNING CAUTION Wrnings tell you wht to
ORGANIZER QUICK REFERENCE GUIDE
NOTES ON ORGANIZING AND SCHEDULING MEETINGS Individul GoToMeeting orgnizers my hold meetings for up to 15 ttendees. GoToMeeting Corporte orgnizers my hold meetings for up to 25 ttendees. GoToMeeting orgnizers
2 DIODE CLIPPING and CLAMPING CIRCUITS
2 DIODE CLIPPING nd CLAMPING CIRCUITS 2.1 Ojectives Understnding the operting principle of diode clipping circuit Understnding the operting principle of clmping circuit Understnding the wveform chnge of
Experiment 6: Friction
Experiment 6: Friction In previous lbs we studied Newton s lws in n idel setting, tht is, one where friction nd ir resistnce were ignored. However, from our everydy experience with motion, we know tht
Operations with Polynomials
38 Chpter P Prerequisites P.4 Opertions with Polynomils Wht you should lern: Write polynomils in stndrd form nd identify the leding coefficients nd degrees of polynomils Add nd subtrct polynomils Multiply
1 GSW IPv4 Addressing
1 For s long s I ve een working with the Internet protools, people hve een sying tht IPv6 will e repling IPv4 in ouple of yers time. While this remins true, it s worth knowing out IPv4 ddresses. Even when
BUSINESS PROCESS MODEL TRANSFORMATION ISSUES The top 7 adversaries encountered at defining model transformations
USINESS PROCESS MODEL TRANSFORMATION ISSUES The top 7 dversries enountered t defining model trnsformtions Mrion Murzek Women s Postgrdute College for Internet Tehnologies (WIT), Institute of Softwre Tehnology
ALPHA ONE GENERATION II STERNDRIVE
LPH ONE GENERTION II STERNDRIVE 2 74243 Tle of Contents Pge Instlltion Speifitions.................. 2-1 Torque Speifitions.................. 2-1 Lurints, Selers, n hesives...... 2-1 Speil Tools..........................
Binary Representation of Numbers Autar Kaw
Binry Representtion of Numbers Autr Kw After reding this chpter, you should be ble to: 1. convert bse- rel number to its binry representtion,. convert binry number to n equivlent bse- number. In everydy
1. Find the zeros Find roots. Set function = 0, factor or use quadratic equation if quadratic, graph to find zeros on calculator
AP Clculus Finl Review Sheet When you see the words. This is wht you think of doing. Find the zeros Find roots. Set function =, fctor or use qudrtic eqution if qudrtic, grph to find zeros on clcultor.
COOLING SYSTEM 6 B CLOSED COOLED MODELS
COOLING SYSTEM 6 B 72987 CLOSED COOLED MODELS Tle of Contents Pge 262 CID / 4.3L........................ 6B-1 Torque Speifitions............... 6B-1 Lurints, Selers And Adhesives.... 6B-1 Speifitions......................
Equivalence Checking. Sean Weaver
Equivlene Cheking Sen Wever Equivlene Cheking Given two Boolen funtions, prove whether or not two they re funtionlly equivlent This tlk fouses speifilly on the mehnis of heking the equivlene of pirs of
New Internet Radio Feature
XXXXX XXXXX XXXXX /XW-SMA3/XW-SMA4 New Internet Rdio Feture EN This wireless speker hs een designed to llow you to enjoy Pndor*/Internet Rdio. In order to ply Pndor/Internet Rdio, however, it my e necessry
OPTIMA QUADRANT / OFFSET QUADRANT
OPTIMA QUADRANT / OFFSET QUADRANT 71799 00 / Issue 1 / 15 Y Z DIMENSIONS Check the enclosure size in the tle elow mtches the showertry instlltion. = Widths: 800 Door = 780-805mm 900 Door = 880-905mm Y
Tablet Charging Wall Mount 12
User's Guide Tlet Chrging Wll Mount 12 For the ltest User Instlltion Guide plese visit: www.ergotron.com User's Guide - English Guí del usurio - Espñol Mnuel de l utilisteur - Frnçis Geruikersgids - Deutsch
Appendix D: Completing the Square and the Quadratic Formula. In Appendix A, two special cases of expanding brackets were considered:
Appendi D: Completing the Squre nd the Qudrtic Formul Fctoring qudrtic epressions such s: + 6 + 8 ws one of the topics introduced in Appendi C. Fctoring qudrtic epressions is useful skill tht cn help you
the machine and check the components
Quik Setup Guide Strt Here MFC-7360N MFC-7460DN Plese red the Sfety nd Legl ooklet first efore you set up your mhine. Then, plese red this Quik Setup Guide for the orret setup nd instlltion. To view the
Section 5-4 Trigonometric Functions
5- Trigonometric Functions Section 5- Trigonometric Functions Definition of the Trigonometric Functions Clcultor Evlution of Trigonometric Functions Definition of the Trigonometric Functions Alternte Form
P.3 Polynomials and Factoring. P.3 an 1. Polynomial STUDY TIP. Example 1 Writing Polynomials in Standard Form. What you should learn
33337_0P03.qp 2/27/06 24 9:3 AM Chpter P Pge 24 Prerequisites P.3 Polynomils nd Fctoring Wht you should lern Polynomils An lgeric epression is collection of vriles nd rel numers. The most common type of
Vectors 2. 1. Recap of vectors
Vectors 2. Recp of vectors Vectors re directed line segments - they cn be represented in component form or by direction nd mgnitude. We cn use trigonometry nd Pythgors theorem to switch between the forms
Chapter. Fractions. Contents: A Representing fractions
Chpter Frtions Contents: A Representing rtions B Frtions o regulr shpes C Equl rtions D Simpliying rtions E Frtions o quntities F Compring rtion sizes G Improper rtions nd mixed numers 08 FRACTIONS (Chpter
Words Symbols Diagram. abcde. a + b + c + d + e
Logi Gtes nd Properties We will e using logil opertions to uild mhines tht n do rithmeti lultions. It s useful to think of these opertions s si omponents tht n e hooked together into omplex networks. To
Installer reference guide
Instller referene guide Dikin Altherm hyrid het pump + EVLQ05+08CA EHYHBH05AA EHYHBH/X08AA Instller referene guide Dikin Altherm hyrid het pump English Tle of ontents Tle of ontents 1 Aout the produt 3
CHAPTER 31 CAPACITOR
. Given tht Numer of eletron HPTER PITOR Net hrge Q.6 9.6 7 The net potentil ifferene L..6 pitne v 7.6 8 F.. r 5 m. m 8.854 5.4 6.95 5 F... Let the rius of the is R re R D mm m 8.85 r r 8.85 4. 5 m.5 m
Start Here. Quick Setup Guide MFC-8710DW MFC-8810DW MFC-8910DW. the machine and check the components
Quik Setup Guide Strt Here MFC-8710DW MFC-8810DW MFC-8910DW Thnk you for hoosing Brother, your support is importnt to us nd we vlue your usiness. Your Brother produt is engineered nd mnuftured to the highest
Inter-domain Routing
COMP 631: COMPUTER NETWORKS Inter-domin Routing Jsleen Kur Fll 2014 1 Internet-sle Routing: Approhes DV nd link-stte protools do not sle to glol Internet How to mke routing slle? Exploit the notion of
1 Fractions from an advanced point of view
1 Frtions from n vne point of view We re going to stuy frtions from the viewpoint of moern lger, or strt lger. Our gol is to evelop eeper unerstning of wht n men. One onsequene of our eeper unerstning
GENERAL OPERATING PRINCIPLES
KEYSECUREPC USER MANUAL N.B.: PRIOR TO READING THIS MANUAL, YOU ARE ADVISED TO READ THE FOLLOWING MANUAL: GENERAL OPERATING PRINCIPLES Der Customer, KeySeurePC is n innovtive prout tht uses ptente tehnology:
- DAY 1 - Website Design and Project Planning
Wesite Design nd Projet Plnning Ojetive This module provides n overview of the onepts of wesite design nd liner workflow for produing wesite. Prtiipnts will outline the sope of wesite projet, inluding
Reasoning to Solve Equations and Inequalities
Lesson4 Resoning to Solve Equtions nd Inequlities In erlier work in this unit, you modeled situtions with severl vriles nd equtions. For exmple, suppose you were given usiness plns for concert showing
ICOM JTG-II PROPANE OPTIMIZATION PROGRAM (POP) INSTALLATION MANUAL FLEET VEHICLES P13X4-9224-AA. Revision: A - Dated 2/13/13 Replaces: None
ICOM JTG-II PROPNE OPTIMIZTION PROGRM (POP) INSTLLTION MNUL P13X4-9224- Revision: - Dated 2/13/13 Replaces: None PROPNE OPTIMIZTION PROGRM OVERVIEW SYSTEM DESCRIPTION THE ICOM PROPNE OPTIMIZTION PROGRM
OxCORT v4 Quick Guide Revision Class Reports
OxCORT v4 Quik Guie Revision Clss Reports This quik guie is suitble for the following roles: Tutor This quik guie reltes to the following menu options: Crete Revision Clss Reports pg 1 Crete Revision Clss
p-q Theory Power Components Calculations
ISIE 23 - IEEE Interntionl Symposium on Industril Eletronis Rio de Jneiro, Brsil, 9-11 Junho de 23, ISBN: -783-7912-8 p-q Theory Power Components Clultions João L. Afonso, Memer, IEEE, M. J. Sepúlved Freits,
FAULT TREES AND RELIABILITY BLOCK DIAGRAMS. Harry G. Kwatny. Department of Mechanical Engineering & Mechanics Drexel University
SYSTEM FAULT AND Hrry G. Kwtny Deprtment of Mechnicl Engineering & Mechnics Drexel University OUTLINE SYSTEM RBD Definition RBDs nd Fult Trees System Structure Structure Functions Pths nd Cutsets Reliility
c b 5.00 10 5 N/m 2 (0.120 m 3 0.200 m 3 ), = 4.00 10 4 J. W total = W a b + W b c 2.00
Chter 19, exmle rolems: (19.06) A gs undergoes two roesses. First: onstnt volume @ 0.200 m 3, isohori. Pressure inreses from 2.00 10 5 P to 5.00 10 5 P. Seond: Constnt ressure @ 5.00 10 5 P, isori. olume
Angles 2.1. Exercise 2.1... Find the size of the lettered angles. Give reasons for your answers. a) b) c) Example
2.1 Angles Reognise lternte n orresponing ngles Key wors prllel lternte orresponing vertilly opposite Rememer, prllel lines re stright lines whih never meet or ross. The rrows show tht the lines re prllel
Quick Guide to Lisp Implementation
isp Implementtion Hndout Pge 1 o 10 Quik Guide to isp Implementtion Representtion o si dt strutures isp dt strutures re lled S-epressions. The representtion o n S-epression n e roken into two piees, the
COMPONENTS: COMBINED LOADING
LECTURE COMPONENTS: COMBINED LOADING Third Edition A. J. Clrk School of Engineering Deprtment of Civil nd Environmentl Engineering 24 Chpter 8.4 by Dr. Ibrhim A. Asskkf SPRING 2003 ENES 220 Mechnics of
4/3-, 4/2- and 3/2- directional valves with switching time adjustment, Model 5-.WE 10 (5-chamber version)
RA 23 351/9.99 RA 23 351/9.99 Replces: 6.98, 8.9 4/3-, 4/2- nd 3/2- directionl vlves with switching time djustment, Model 5-.WE 1 (5-chmer version) Nominl size 1 Series 3X Mximum operting pressure 4569
European Convention on Products Liability in regard to Personal Injury and Death
Europen Trety Series - No. 91 Europen Convention on Produts Liility in regrd to Personl Injury nd Deth Strsourg, 27.I.1977 The memer Sttes of the Counil of Europe, signtory hereto, Considering tht the
Further applications of area and volume
2 Further pplitions of re n volume 2A Are of prts of the irle 2B Are of omposite shpes 2C Simpson s rule 2D Surfe re of yliners n spheres 2E Volume of omposite solis 2F Error in mesurement Syllus referene
CS 316: Gates and Logic
CS 36: Gtes nd Logi Kvit Bl Fll 27 Computer Siene Cornell University Announements Clss newsgroup reted Posted on we-pge Use it for prtner finding First ssignment is to find prtners P nd N Trnsistors PNP
Clause Trees: a Tool for Understanding and Implementing Resolution in Automated Reasoning
Cluse Trees: Tool for Understnding nd Implementing Resolution in Automted Resoning J. D. Horton nd Brue Spener University of New Brunswik, Frederiton, New Brunswik, Cnd E3B 5A3 emil : jdh@un. nd spener@un.
GAMES OF THE XXX OLYMPIAD
GAMES OF THE XXX OLYMPIAD London (GBR) 29 July to 11 August 2012 COMPETITION REGULATIONS MEN S AND WOMEN S HOCKEY COMPETITIONS Pulished: July 2012 INTERNATIONAL HOCKEY FEDERATION First pulished Mrh 2012;
ELECTRICAL SYSTEMS IGNITION SYSTEM
ELECTRICAL SYSTEMS 4 71855 B IGNITION SYSTEM Tle of Contents Pge Identifiction............................ 4B - 1 Replcement Prts Wrning.............. 4B - 2 Sprk Plugs.......................... 4B - 2
Power consumption In operation At rest For wire sizing. Rated impulse voltage Control pollution degree 3. Non-operating temperature
echnicl dt sheet SRF2A-5(-O) Rotry ctutor with emergency function for utterfly vlves orque orue 2 2 2 m m m ominl voltge AC/DC 2 V Control Control Open-close Oen-close SRF2A-5 SRF2A-5 Deenergised C C SRF2A-5-O
KNOWING YOUR SEWING MACHINE SEWING BASICS VARIOUS STITCHES APPENDIX
KNOWING YOUR SEWING MACHINE SEWING BASICS VARIOUS STITCHES APPENDIX Plese visit us t http://solutions.rother.om where you n get produt support nd nswers to frequently sked questions (FAQs). INTRODUCTION
ALPHA ONE GENERATION II STERN DRIVE
LPH ONE GENERTION II STERN DRIVE 2 74243 Tle of Contents Pge Instlltion Speifitions.................. 1 Torque Speifitions....................... 1 Lurints, Selers, n hesives.......... 1 Speil Tools..............................
Bayesian Updating with Continuous Priors Class 13, 18.05, Spring 2014 Jeremy Orloff and Jonathan Bloom
Byesin Updting with Continuous Priors Clss 3, 8.05, Spring 04 Jeremy Orloff nd Jonthn Bloom Lerning Gols. Understnd prmeterized fmily of distriutions s representing continuous rnge of hypotheses for the
JCM TRAINING OVERVIEW Multi-Download Module 2
Multi-Downlo Moule 2 JCM Trining Overview Mrh, 2012 Mrh, 2012 CLOSING THE MDM2 APPLICATION To lose the MDM2 Applition proee s follows: 1. Mouse-lik on the 'File' pullown Menu (See Figure 35 ) on the MDM2
A.7.1 Trigonometric interpretation of dot product... 324. A.7.2 Geometric interpretation of dot product... 324
A P P E N D I X A Vectors CONTENTS A.1 Scling vector................................................ 321 A.2 Unit or Direction vectors...................................... 321 A.3 Vector ddition.................................................
Or more simply put, when adding or subtracting quantities, their uncertainties add.
Propgtion of Uncertint through Mthemticl Opertions Since the untit of interest in n eperiment is rrel otined mesuring tht untit directl, we must understnd how error propgtes when mthemticl opertions re
Car insurance. Policy Booklet. www.tesco.ie. In association with
Cr insurne Poliy Booklet www.teso.ie In ssoition with Teso Cr Insurne poliy ontents Generl Cutting the ost, not the over! Speil notes, ident nd rekdown ssist phone numers 2 Introdution 3 Complints proedure
CallPilot 100/150 Upgrade Addendum
CllPilot 100/150 Relese 3.0 Softwre Upgrde Addendum Instlling new softwre onto the CllPilot 100/150 Feture Crtridge CllPilot 100/150 Upgrde Addendum Prerequisites lptop or desktop computer tht cn ccept
Use Geometry Expressions to create a more complex locus of points. Find evidence for equivalence using Geometry Expressions.
Lerning Objectives Loci nd Conics Lesson 3: The Ellipse Level: Preclculus Time required: 120 minutes In this lesson, students will generlize their knowledge of the circle to the ellipse. The prmetric nd
Data Security 1. 1 What is the function of the Jump instruction? 2 What are the main parts of the virus code? 3 What is the last act of the virus?
UNIT 18 Dt Seurity 1 STARTER Wht stories do you think followed these hedlines? Compre nswers within your group. 1 Love ug retes worldwide hos. 2 Hkers rk Mirosoft softwre odes. 3 We phone sm. Wht other
Lec 2: Gates and Logic
Lec 2: Gtes nd Logic Kvit Bl CS 34, Fll 28 Computer Science Cornell University Announcements Clss newsgroup creted Posted on we-pge Use it for prtner finding First ssignment is to find prtners Due this