USB2.0. Harddisk Case MD-206. Manual

Transcription

1 USB2.0 Harddisk Case MD-206 Manual

2 Introduction This hard disk case provides a fast and easy way to add more storage space to your PC. This product can be easily connected to your PC or Notebook using a USB interface, it can even be disconnected and re-connected while the computer is running. USB 2.0 provides performance enhancements over USB 1.1 and offers forward and backward compatibility with USB 1.1 devices. 1. Package Contents External Hi-Speed USB2.0 Harddisk Case USB2.0 A-B Cable CD-ROM Power adapter Quick Installation Guide 2. Specifications 2.1 System Requirements PC with Pentium 233MHz or faster CPU Windows ME, 2000, XP or Vista MAC OS 10 or higher Macintosh OS 10.x or higher 64MB RAM Available USB1.1 or USB2.0 port* 3.5 SATA hard disk. * When using a USB1.1 port the drive will operate at 12 Mbps 2.2 Features Complies with USB Specification 1.1 & 2.0 Supports high (full)-speed transfer mode Supports every standard SATA HDD. Lightweight compact case 2.3 Specifications USB Version 2.0 Compliant High Speed (480 Mbps) And Full Speed (12 Mbps) Support USB Mass Storage Class Bulk-Only Specification Compliant (Version 1.0)

3 3. Hardware Assembly Note: If you have purchased this product with a built-in hard disk continue to chapter 4. Open the hard disk's housing by removing the two screws on the rear. Connect the SATA connector and the power supply connector to the SATA hard disk. Use the screws provided to attach the metal plate to the hard disk.

4 Push the hard disk and the rear of the housing back into place. Secure the rear of the hard disk's housing in position and then fit the screws in the side of the housing.

5 4. Software Installation 4.1 Hardware Installation Regardless of which operating system your computer is running, follow the install procedure below in order to properly connect the USB A-mini -B cable, the AC adapter and the power cord. Shut down your pc. Plug the B-type connector of the USB2.0 A-B cable, into the Sitecom Hard Disk Case and plug the A-type connector of the USB A-mini -B cable into the USB2.0 port of your PC. Start your pc and proceed to chapter 4.2 for Windows ME, 2000 or XP or chapter 4.3 for Macintosh. 4.2 Software Installation Windows ME/2000/XP/Vista Windows ME, 2000, XP & Windows Vista do not require software installation. Native Windows drivers are used. Windows ME, 2000, XP and Vista will recognize and install the Sitecom Hard Disk Case automatically. No additional drivers are necessary. Check My Computer or Explorer, there should be a new icon and drive letter for the Sitecom Hard Disk Case (if the hard disk is formatted). If the hard disk placed in the hard disk case has not been formatted, continue to chapter Software Installation Macintosh OS X Mac OS X does not require software installation. Native drivers are used. Mac OS will recognize and install the Sitecom Hard Disk Case automatically. No additional drivers are necessary. On the desktop should be a new icon. Click the icon to access the Hard Disk Case If this icon does not appear, you have to mount the drive. Click Go, select Utilities. A new menu appears, select disk utilities to mount or un-mount the disk.

6 To check the properties of the disk, click Go, Utilities. A new menu appears, select System Profile to view the properties of the MD-206. If the hard disk placed in the hard disk case has not been formatted, continue to chapter 5.3.

7 5. Initializing a New Hard Disk 5.1 Windows Vista Click on the Start menu, then click Control Panel. Open the System and Maintenance section. Go to the Administrative Tools section. Click on Create and Format hard disk partitions. Depending on your Windows UAC settings, you might need to give permission to execute this command. The USB Hard Drive will be listed without a drive letter, and show as unallocated. To create a partition, right mouse click once on the unallocated area of the USB Hard Drive and choose New Simple Volume. Note: Selecting the wrong area at this stage may cause you to lose valuable data.

8 The New Simple Volume Wizard will appear. Click Next to continue. Enter the amount of disk space to be used (the partition size), then click Next. The default is the maximum available disk space. Assign a drive letter or path, then click Next.

9 Select a file system to format the disk (FAT32, or NTFS), then click Next. Click Finish to begin formatting the USB Hard Drive. When formatting has finished, the USB Hard Drive will display the volume name, the drive letter, the size of the partition (in GB), the file system used (FAT32, or NTFS), and a Healthy status. The USB Hard Drive is now available to use.

10 5.2 Windows XP & 2000 Click on the Start menu, then click Settings, and then click Control Panel, and double-click on Administrative Tools. Double-click on Computer Management. In the Storage sub-directory, click on Disk Management. The USB Hard Drive will be listed without a drive letter, and show as unallocated. To create a partition, right mouse click once on the unallocated area of the USB Hard Drive and choose Create partition. Note: Selecting the wrong area at this stage may cause you to lose valuable data. The Create Partition wizard will appear. Click Next to continue.

11 Choose Primary or Extended Partition, and then click Next (Primary Partition is recommended). Enter the amount of disk space to be used (the partition size), then click Next. The default is the maximum available disk space. Assign a drive letter or path, then click Next.

12 Select a file system to format the disk (FAT, FAT32, or NTFS), then click Next (The FAT file system is only available if the partition size is less than 2GB). Click Finish to begin formatting the USB Hard Drive. When formatting has finished, the USB Hard Drive will display the volume name, the drive letter, the size of the partition (in GB), the file system used (FAT, FAT32, or NTFS), and a Healthy status.

13 The USB Hard Drive is now available to use. 5.3 Windows 98/ME Click Start and then type Run in the command prompt. Type fdisk and click OK button. Press the letter Y and hit Enter. You will see a menu with 5 options. You should type 5 to select the Change current fixed disk drive option then hit the Enter key.

14 You should see a list of hard drives. Your main internal hard drive will be Disk 1. Any other hard drives will be listed as 2, 3, etc. If you have only one hard drive in your computer then drive 2 will be the USB Hard Drive. You can also verify which drive on the list is the USB hard drive by the size under Mbytes. The number should be approximately equal to the size marked on the front label of your hard drive. Choose the number that represents the USB hard drive and type it then hit the Enter key. Note: Selecting the wrong disk at this stage may cause you to lose valuable data. You now are presented with the original menu of 5 items. This time, you must choose option 1, Create DOS partition or Logical DOS drive and hit Enter. You are presented with another menu of 3 items.. You must choose option 1, Create Primary DOS Partition. Verify that you are partitioning the correct disk number before proceeding. Then hit the Enter key. This may take about a

15 minute. You will now see the question Do you wish to use the maximum available size for a Primary DOS partition? Answer yes or just hit the Enter key. This may take a minute. When the partitioning is complete hit the Esc button twice. You will see a message that you must restart your PC. You can ignore this message. Hit the Esc button once more to exit the fdisk program. Double click the My Computer icon. Unplug the USB hard drive and then reconnect it to your PC. An icon with a drive letter will show up in the My Computer window. When you try to access the drive you will get a dialog box with the message that the drive is not accessible. Click Cancel button. You now need to format your USB hard drive. In the My Computer window, point your cursor to the icon that represents the USB hard drive and click the right mouse button. Select Format. Note: Selecting the wrong disk at this stage may cause you to lose valuable data. In the Format window select format type Full and type a label name (10 characters or less), click the Start button to start formatting.

16 You will see a warning that all files will be destroyed. Click the OK button to proceed. Once the format is complete please click Close. Windows will ask you to run Scandisk before using the disk. You can ignore this message, click OK. Close the Windows Help window. The USB disk is now ready to be used. 5.3 Macintosh OS X and higher Please go to Utilities/Disk Utility to partition the disk. Select the hard disk and choose to partition.

17 6. Using the Hard Disk Case Open My Computer or File Explorer. Double-click on the correct Disk icon. Access images and files on your Hard Disk Case the same way you open, copy, move, or delete images and files on your normal hard disk drive. Saving files to your computer from the Hard Disk Case Locate or create a destination folder you wish to transfer the files to on your computer. (i.e. create a new folder on the desktop) Open 'My Computer' or 'File Explorer', open the folder containing the files on the Hard Disk Case. Go to the edit menu and choose Select all. Go to the edit menu and choose Copy. Go to the destination folder. Go to the edit menu and choose Paste. The files will be copied to the destination folder. Mac OS X You can use the disk the same way as the normal Harddisk

18 7. Turning off the Hard Disk Case Mounting/Dismounting When a device, such as a Hard Disk Case, is mounted on a computer, it means the computer sees the device and is able to communicate with it. When you dismount a device the computer no longer sees it. The device may still be running but the computer cannot access it, as though the device no longer exists. Before you turn off a Hard Disk Case with the computer running, you must dismount the drive. If you turn off the drive without dismounting it first, data on the drive may be lost or damaged. If you turn off your computer before you turn off your Sitecom Hard Disk Case, no dismounting is needed. Always make sure the drive is turned off before disconnecting the AC adapter or the USB cable. Locate the System Tray and the unplug icon. Left-click the unplug icon. Windows ME A rectangle will appear with the name of the drive followed by the drive letter. Windows 2000/XP/Vista You will receive the alert message Safely Remove or Stop followed by the drive letter for the device. Left-click the appropriate device (with the drive letter matching the one used by the Sitecom Hard Disk Case). After a few seconds, Windows will show a message that it is safe to remove the device. Click OK and the Hard Disk Case will dismount. You can now safely turn the Hard Disk Case off. Mac OS X Drag the hard disk icon on the desktop to the trashcan icon to dismount the hard disk.