AIR-CELL Permishield. Typical Design Detail. Thermal Performance. Installation Instructions. Specification Guide. Plasterboard lining fixed to stud

Transcription

1 Insulation A4/8 TF AW1196 Issue 4 Nov 2012 Timber-framed Walls Insulation guide Helps achieve a 6-star house energy rating Rigid Kingspan Kooltherm and flexible Kingspan AIR-CELL solutions available Fibre-free, non-allergenic, non-irritant solutions available Quick and easy to install Solutions available that act as a temporary weather barrier prior to wall cladding being fixed Strong, tough, durable Rodent and insect resistant Compliant with BCA and AS/NZS

2 AIR-CELL Permishield Typical Design Detail Plasterboard lining fixed to stud Timber stud wall frame Kingspan AIR-CELL Permishield External wall cladding Vertical batten Kingspan AIR-CELL Permishield Stud wall frame Plasterboard lining fixed to stud Vertical counterbatten External wall cladding Figure 1 Timber-framed wall installation using counter-battens Thermal Performance Timber-framed Wall Heat flow in Heat flow out Kingspan AIR-CELL Permishield 65 R T 1.6 R T 1.8 Kingspan AIR-CELL Permishield 80 R T 1.7 R T 1.9 The R-values shown are Total R-values for the building element as required by the Energy Provisions of the Building Code of Australia. Kingspan AIR-CELL products are manufactured, tested and packaged in conformance with AS/NZS The contribution of the product Total R-values depends on installation and environmental conditions. Specification Guide The wall insulation fixed to the outside of the stud frame shall be vapour-permeable, CodeMark-certified Kingspan AIR-CELL Permishield (specify 65 or 80) fibre-free, thermo reflective insulation, comprising a cross-linked, closed-cell foam core sandwiched with an anti-glare foil facing on one side and a plain foil facing on the other side manufactured by Kingspan Insulation, and shall be installed in accordance with the instructions issued by them. Figure 2 Side elevation of Kingspan AIR-CELL Permishield on timber-framed wall Installation Instructions 1. Roll out Kingspan AIR-CELL Permishield horizontally and fix to outside of frame. 2. Cut Kingspan AIR-CELL Permishield carefully around doors, windows and other openings, so that it neatly abuts to frames. 3. Butt join insulation sheets and tape with a 48 mm wide reinforced foil tape. 4. Fix counter battens and exterior cladding. 2

3 Kooltherm K5 External Wall Board Typical Design Detail Mechanical fixings Kingspan Kooltherm K5 External Wall Board EML or glass fibre mesh Plasterboard Timber stud Airspace (created by Stud) Kingspan Kooltherm K5 External Wall Board Polymer Render Render Texture coat or membrane finish Figure 3 Kingspan Kooltherm K5 External Wall Board on timber-framed wall Thermal Performance Product Thickness Heat flow in Heat flow out 50 mm R T 3.0 R T 3.0 Figure 4 Side elevation of Kingspan Kooltherm K5 External Wall Board on timber-framed wall Installation Instructions Please refer to the Kingspan Kooltherm K5 External Wall Board General Installation Guide for full details. 80 mm R T 4.5 R T 4.5 The R-values shown are Total R-values for the building element as required by the Energy Provisions of the Building Code of Australia. Kingspan Kooltherm products are manufactured, tested and packaged in conformance with AS/NZS The contribution of the product Total R-values depends on installation and environmental conditions. Specification Guide The external wall insulation shall be Kingspan Kooltherm K5 External Wall Board mm thick comprising a CFC/ HCFC free and zero Ozone Depletion Potential (ODP) rigid thermoset insulation core with a tissue based facing on both sides manufactured under a management system certified to BS / I.S. EN ISO 9001:2008, BS / I.S. EN ISO 14001:2004 and BS / I.S. OHSAS 18001:2007 by Kingspan Insulation Pty Limited and shall be installed by approved installers (please contact Kingspan Insulation). 3

4 Kooltherm K12 Framing Board Typical Design Detail Timber stud Kingspan Kooltherm K12 Framing Board Lightweight cladding Cladding Vertical Counter-Batten Kingspan Kooltherm K12 Framing Board Airspace (created by Stud) Plasterboard Counter batten Figure 5 Kingspan Kooltherm K12 Framing Board on timberframed wall Thermal Performance Product Thickness Heat flow in Heat flow out 25 mm R T 2.8 R T mm R T 3.0 R T 3.2 The R-values shown are Total R-values for the building element as required by the Energy Provisions of the Building Code of Australia. Kingspan Kooltherm products are manufactured, tested and packaged in conformance with AS/NZS The contribution of the product Total R-values depends on installation and environmental conditions. Specification Guide The wall insulation shall be Kingspan Kooltherm K12 Framing Board mm thick comprising a CFC/HCFC free and zero Ozone Depletion Potential (ODP) rigid thermoset insulation core with composite foil facings on both sides manufactured under a management system certified to BS / I.S. EN ISO 9001:2008, BS / I.S. EN ISO 14001:2004 and BS / I.S. OHSAS 18001:2007 by Kingspan Insulation Pty Limited and shall be installed in accordance with the instructions issued by them. Figure 6 Side elevation Timber-framed wall with Kingspan Kooltherm K12 Framing Board and vertical counter-battens Installation Instructions 1. Ensure that stud spacings do not exceed 600 mm centres. 2. Fix Kingspan Kooltherm K12 Framing Board to the external surface of the frame structure ensuring vertical board joints coincide with a vertical member. 3. Ensure that the boards are lightly butted and continuity of insulation is maintained. 4. Use large headed galvanised clout nails or screws as temporary fixings prior to the secondary support batten being fitted. 5. Fix preservative treated softwood battens vertically to the wall frame, through the insulation sheathing, ensuring that the battens and fixings are coincident with the underlying timber studs, top and bottom plates. 6. Consider the weight of cladding when selecting the type of fixing and fixing frequency for the battens. 7. Fix the external cladding panel to the secondary support batten in the traditional manner. 4

5 Kooltherm K18 Insulated Plasterboard Typical Design Detail Kingspan Kooltherm K18 Insulated Plasterboard Timber stud Lightweight cladding Sarking / Breather membrane Kingspan Kooltherm K18 Insulated Plasterboard Figure 7 Kingspan Kooltherm K18 Insulated Plasterboard mechanically fixed to internal side of timber-frame Thermal Performance Product Thickness (inc. Plasterboard) Heat flow in Heat flow out Figure 8 Side elevation - Lightweight cladded timber-framed wall with Kingspan Kooltherm K18 Insulated Plasterboard Installation Instructions 35 mm R T 2.1 R T mm R T 2.4 R T mm R T 2.9 R T mm R T 3.5 R T mm R T 4.0 R T mm R T 4.5 R T mm R T 5.0 R T 5.1 The R-values shown are Total R-values for the building element as required by the Energy Provisions of the Building Code of Australia. Kingspan Kooltherm products are manufactured, tested and packaged in conformance with AS/NZS The contribution of the product Total R-values depends on installation and environmental conditions. Specification Guide The wall dry-lining insulation shall be Kingspan Kooltherm K18 Insulated Plasterboard mm thick, comprising a CFC/HCFC-free and zero Ozone Depletion Potential (ODP) rigid thermoset insulation core with 10 mm plasterboard facing bonded to its front surface and a composite foil facing on its reverse surface, manufactured under a management system certified to BS / I.S. EN ISO 9001:2008, BS / I.S. EN ISO 14001:2004 and BS / I.S. OHSAS 18001:2007 by Kingspan Insulation Pty Limited and shall be installed in accordance with the instructions issued by them. Kingspan Kooltherm K18 Insulated Plasterboard must be installed in accordance with AS/NZS 2589:2007 Gypsum linings Application and finishing. Mechanical Fixing to Vertical Timber / Battens / Metal Stud and Track This method may be used on timber frame, metal stud and track constructions or on any dry masonry wall that will support and retain the battens and associated fixings. 1. Place framing / battens at a maximum of 600 mm centres and positioned horizontally at floor and ceiling level / horizontal joints to support the Kingspan Kooltherm K18 Insulated Plasterboard. 2. Ensure the framing/ battens will be wide enough to offer a minimum 20 mm support to all edges of the board. 3. Use plasterboard screws long enough to allow for a minimum 20 mm embedment into the stud or, alternatively, suitable galvanised plasterboard nails, should be placed at 200 mm centres and not less than 10 mm from the edges of the board along the line of the studs. 4. Drive fixings straight and embed heads just below the surface of the board. Care should be taken not to overdrive the fixing. 5. Screws used for plasterboard fixing must comply with AS :2002 self-drilling screws complying with the building and construction industry corrosion resistance requirements. 5

6 General Requirements Cutting 1. Fit Kingspan AIR-CELL neatly around doors, windows, and any penetrations, and tape if necessary to prevent air leakage. 2. Foil facings are conductive to electricity and contact with uninsulated electrical cables and fittings must be avoided. 3. When taping a plastic squeegee or blade must be used to apply appropriate pressure to the tape. Surfaces must be dry and free from dust, oil or grease prior to taping. 4. Leave minimum 50 mm clearance around heat producing flues or light fittings (refer to light fitting manufacturer). The instructions in this document are guidelines only and should be interpreted with consideration for the specific building design. The installation of Kingspan AIR-CELL should be in conformance with the applicable clauses from AS 3999 and AS/NZS unless otherwise specified. Kingspan AIR-CELL can be damaged by intense heat above 105 C and contact with sparks and flame from blow torches, welders, cutting tools, etc. must be avoided. The installer must make due provision for safety when installing Kingspan AIR-CELL and Kingspan Kooltherm in any application. Cutting of Kingspan Kooltherm boards should be carried out either by using a fine toothed saw, or by scoring with a sharp knife, snapping the board over a straight edge and then cutting the facing on the other side. Ensure accurate trimming to achieve close-butting joints and continuity of insulation. Please note that scoring and snapping would not apply to Kingspan Kooltherm K18 Insulated Plasterboard due to the bonded plasterboard lining. Handling and Storage Kingspan AIR-CELL insulation products must be transported and stored in its protective packaging and kept clean and dry. Standing rolls on end reduces risk of damage should moisture be present in the packaging. Surfaces must be kept free of contaminants such as dust and grease, and must not be stored with foil surfaces in contact with alkaline materials i.e. wet cement, lime, etc. The packaging of Kingspan Kooltherm should not be considered adequate for long term outdoor protection. Ideally boards should be stored inside a building. If, however, outdoor storage cannot be avoided then the boards should be stacked clear of the ground and covered with an opaque polythene sheet or weatherproof tarpaulin. Boards that have been allowed to get wet should not be used. 6

7 7

8 Contact Details General Enquiries Tel: Kingspan Insulation Pty. Ltd. reserves the right to amend product specifications without prior notice. The information, technical details and fixing instructions etc. included in this literature are given in good faith and apply to uses described. Recommendations for use should be verified as to the suitability and compliance with actual requirements, specifications and any applicable laws and regulations. For other applications or conditions of use, Kingspan Insulation offers a Technical Advisory Service the advice of which should be sought for uses of Kingspan Insulation products that are not specifically described herein. Please check that your copy of the literature is current by contacting us or visiting Kingspan Insulation Pty Ltd Tel: info@kingspaninsulation.com.au Kingspan, Kooltherm, Air-Cell, the zo Device and the Lion Device are Registered Trademarks of the Kingspan Group plc in Australia and other countries. All rights reserved. Kingspan Insulation Pty Ltd