NS5B1G384. Single (NC) Normally Closed SPST Analog Switch

Transcription

1 Single (NC) Normally Closed SPST Analog Switch The NSB1G384 is Single Pole Single Throw (SPST) high-speed TTL-compatible switch. The low resistance and capacitance characteristics of this switch make it ideal for low-distortion audio, video, and data routing applications. The switch has a normally closed logic configuration meaning the switch is on (NC connected to COM) when IN is low. These switches are available in -pin SC 70 and -pin TSOP (SOT23 ) packages for operation over the industrial (-40 C to +8 C) temperature range. Features Operating Range: 2.0 V to. V Low On Resistance : R ON : 4.0 = 4. V Minimal Propagation Delay : t pd < 0. ns Control Compatible with TTL Levels ESD Performance: Human Body Model > ±2 kv -Pin SC 70 or -Pin TSOP Packages Available These are Pb Free Devices Typical Applications Audio, Video, and High-Speed Data Switching Mobile Phones Portable Devices Desktop & Notebook Computing 1 SC 70 CASE 419A TSOP (SOT23 ) CASE 483 MARKING DIAGRAMS AG = For SC 70 AD = For TSOP M = Date Code = Pb Free Package (Note: Microdot may be in either location) 1 LOGIC DIAGRAM AG M AD M NC COM IN PIN ASSIGNMENTS COM 1 NC 2 GND 3 4 IN ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. Semiconductor Components Industries, LLC, 2012 August, 2012 Rev. 1 1 Publication Order Number: NSB1G384/D

2 PIN DESCRIPTION PIN # Name Direction Description 1 COM I/O Common Signal Line 2 NC I/O Normally Closed Signal Line 3 GND Ground 4 IN Control Signal Line Voltage Supply TRUTH TABLE IN Control L H Function NC Connected to COM NC Disconnected from COM MAXIMUM RATINGS Symbol Pins Rating Value Condition Positive DC Supply Voltage 0. to +7.0 V V IS NC or COM Analog Signal Voltage 0. to + 0. V V IN IN Control Voltage 0. to +7.0 V I IS_CON NC or COM Analog Signal Continuous Current 300 Closed Switch ma I IS_PK NC or COM Analog Signal Peak Current 00 10% Duty Cycle ma I IN IN Control Current 20 ma T STG Storage Temperature Range 6 to 10 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. RECOMMENDED OPERATING CONDITIONS Symbol Pins Parameter Value Condition Positive DC Supply Voltage 2.0 to. V V IS NC or COM Analog Signal Voltage GND to V V IN IN Control Voltage GND to. V T A Operating Temperature Range 40 to +8 C t r, t f Rise or Fall Time 20 = 3.3 V ns/v 10 =.0 V Minimum and maximum values are guaranteed through test or design across the Recommended Operating Conditions, where applicable. Typical values are listed for guidance only and are based on the particular conditions listed for each section, where applicable. These conditions are valid for all values found in the characteristics tables unless otherwise specified in the test conditions. ESD PROTECTION Pins Description Minimum Voltage All Pins Human Body Model 2 kv 2

3 DC ELECTRICAL CHARACTERISTICS CONTROL INPUT (Typical: T = 2 C) 40 C to +8 C V IH IN Control High V V IL IN Control Low V I IN IN Control Leakage 0 V IN.0 ±0.1 ±0. A SUPPLY CURRENT AND LEAKAGE (Typical: T = 2 C) I NC (OFF) I COM (OFF) NC OFF State Leakage V IN = V IL or V IH V NC = 1.0 V V COM = 4. V COM OFF State Leakage V IN = V IL or V IH V NC = 4. V V COM = 1.0 V I CC Quiescent Supply V IN and V IS = or GND I D = 0 A 40 C to +8 C. ±10 ±100 na. ±10 ±100 na 2.0. ±0.1 ±1.0 A I OFF IN Power Off Leakage V IN =. V or GND 0 ±0. ±1.0 A ON RESISTANCE (Typical: T = 2 C) 40 C to +8 C R ON NC, COM ON Resistance V IS = 0 V, I ON = 30 ma V IS = 0 V, I ON = 64 ma V IS = 2.4 V, I ON = 1 ma

4 AC ELECTRICAL CHARACTERISTICS TIMING/FREQUENCY (Typical: T = 2 C, R L = 0, C L = 3 pf, f = 1 MHz) 40 C to +8 C t ON IN to NC Turn On Time As Above, Figures 1 and ns t OFF IN to NC Turn Off Time As Above, Figures 1 and ns t PD NC to COM Propagation Delay ns BW 3dB Bandwidth C L = pf, Figures 3 and MHz CAPACITANCE (Typical: T = 2 C, R L = 0, C L = pf, f = 1 MHz) 40 C to +8 C C IN IN Control 0 V 2.2 pf C ON NC to COM Through Switch V IN = 0V 4. V 12 pf C OFF NC Unselected Port V IS = 4. V, V IN = 4. V 4. V 4.1 pf DEVICE ORDERING INFORMATION Device Order Number Package Type Tape & Reel Size NSB1G384DFT2G NSB1G384DTT1G SC 70 (Pb Free) TSOP (Pb Free) 3000 / Tape & Reel 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. 4

5 DUT 0 V 0% 0% 0.1 F Open V OUT 0 3 pf V OH 90% 90% V OL t ON t OFF Figure 1. t ON /t OFF DUT 0 0 V 0% 0% Open V OUT 3 pf VOH V OL 10% 10% t OFF t ON Figure 2. t ON /t OFF Reference DUT 0 0 Generator Transmitted 0 Channel switch control/s test socket is normalized. Off isolation is measured across an off channel. On loss is the bandwidth of an On switch. V ISO, Bandwidth and V ONL are independent of the input signal direction. V ISO = Off Channel Isolation = 20 Log V OUT for V IN at 100 khz VIN V ONL = On Channel Loss = 20 Log V OUT for V IN at 100 khz to 0 MHz VIN Bandwidth (BW) = the frequency 3 db below V ONL V CT = Use V ISO setup and test to all other switch analog input/outputs terminated with 0 Figure 3. Off Channel Isolation/On Channel Loss (BW)/Crosstalk (On Channel to Off Channel)/V ONL

6 MAGNITUDE (db) FREQUENCY (Hz) Figure 4. Typical =. V, 2 C MAGNITUDE (db) FREQUENCY (Hz) Figure. Off Channel =. V, 2 C PERCENT (%) FREQUENCY (Hz) Figure 6. Typical Total Harmonic = 4. V 6

7 PACKAGE DIMENSIONS SC 88A (SC 70 /SOT 33) CASE 419A 02 ISSUE K S A G 4 B D PL 0.2 (0.008) M B M N NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.M, CONTROLLING DIMENSION: INCH A 01 OBSOLETE. NEW STANDARD 419A DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D G BSC 0.6 BSC H J K N REF 0.20 REF S C J H K 7

8 PACKAGE DIMENSIONS TSOP, SOT23 CASE ISSUE H 2X 2X NOTE 0.10 T 0.20 T L H G A B C D X 0.20 C A B T S SEATING PLANE J K DETAIL Z M DETAIL Z NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.M, CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS.. OPTIONAL CONSTRUCTION: AN ADDITIONAL TRIMMED LEAD IS ALLOWED IN THIS LOCATION. TRIMMED LEAD NOT TO EXTEND MORE THAN 0.2 FROM BODY. MILLIMETERS DIM MIN MAX A 3.00 BSC B 1.0 BSC C D G 0.9 BSC H J K L M 0 10 S SOLDERING FOOTPRINT* SCALE 10:1 mm inches *For additional information on our Pb Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC s product/patent coverage may be accessed at Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 163, Denver, Colorado USA Phone: or Toll Free USA/Canada Fax: or Toll Free USA/Canada orderlit@onsemi.com N. American Technical Support: Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: Japan Customer Focus Center Phone: ON Semiconductor Website: Order Literature: For additional information, please contact your local Sales Representative NSB1G384/D