SPEC NO: DSAE7979 REV NO: V.12B DATE: JUL/01/2016 PAGE: 1 OF 5 APPROVED:

Transcription

1 1.0X0.5mm SMD CHIP LED LAMP Part Number: APHHS1005CGCK Green Features 1.0mmx0.5mm SMD LED, 0.5mm thickness. Low power consumption. Wide viewing angle. Ideal for backlight and indicator. Package: 2000pcs / reel. Moisture sensitivity level : level 3. RoHS compliant. Description The Green source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode. Package Dimensions 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAE7979 REV NO: V.12B DATE: JUL/01/2016 PAGE: 1 OF 5

2 Selection Guide Part No. Emitting Color (Material) Lens Type Iv (mcd) 20mA Viewing Angle [1] Min. Typ. 2θ1/2 APHHS1005CGCK Green (AlGaInP) Water Clear θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to CIE standards. Electrical / Optical Characteristics at TA=25 C Symbol Parameter Emitting Color Typ. Max. Units Test Conditions λpeak Peak Wavelength Green 574 nm IF=20mA λd [1] Dominant Wavelength Green 570 nm IF=20mA Δλ1/2 Spectral Line Half-width Green 20 nm IF=20mA C Capacitance Green 15 pf VF=0V;f=1MHz VF [2] Forward Voltage Green V IF=20mA IR Reverse Current Green 10 ua VR=5V 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25 C Parameter Values Units Power dissipation 75 mw DC Forward Current 30 ma Peak Forward Current [1] 150 ma Reverse Voltage 5 V Operating Temperature Storage Temperature -40 C To +85 C -40 C To +85 C 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAE7979 REV NO: V.12B DATE: JUL/01/2016 PAGE: 2 OF 5

3 Green APHHS1005CGCK SPEC NO: DSAE7979 REV NO: V.12B DATE: JUL/01/2016 PAGE: 3 OF 5

4 APHHS1005CGCK Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions SPEC NO: DSAE7979 REV NO: V.12B DATE: JUL/01/2016 PAGE: 4 OF 5

5 PACKING & LABEL SPECIFICATIONS APHHS1005CGCK Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at SPEC NO: DSAE7979 REV NO: V.12B DATE: JUL/01/2016 PAGE: 5 OF 5