Job Hazard/Safety Analysis For the Cabinet Maker

Transcription

1 Job Hazard/Safety Analysis For the Cabinet Maker 1

2 INTRODUCTION Job Hazard/Safety Analysis for the Cabinet Maker is a partial list of known task performed by the professional cabinet maker. We have placed task in alphabetical order and in a table format, listing each in a step-by-step sequence followed by the potential hazard and a recommended action or procedure. This is by no means an exhaustive list and is subject to modification. Additional comments may be added as more information becomes available. If you are asked to perform an occasional task, not listed with your job title, you can look up an individual task by returning to our Job Safety Analysis page and check the pulldown menu for Job Task. 2

3 APHABETICAL LIST OF TASK Page Air Compressor 4 Battery Charger 5 Bench Grinder 6 Chain Hoist 7 Chemicals (Pouring Handling) 8 Cleaning (Sweep & Mop) 9 Cutoff Saw 10 Drill Bit Sharpener 11 Drill Press 12 Drum Handling (30-55 Gal.) 13 Floor Jack, Hydraulic 14 Forklift 15 Fuel Transfer Pump 16 Hand Held Portable Power Tools 17 Heat Gun 18 Hoist (Electric/Manual) Slings 19 Hydraulic Press 20 Jack Stands, Manual 21 Lifting/Carrying Objects 22 Miter Saw 23 Pallet Jack & Dolly, Hydraulic 24 Portable Generator, Gasoline Powered 25 Portable Heater, Electric Powered 26 Portable Heater, Gasoline Powered 27 Power Hacksaw 28 Propane Torch (14-20 oz. Cylinder) 29 Shop Vac(s) 30 Soldering Guns/Irons 31 Vise 32 3

4 Hazard Analysis: Air Compressor, Portable, Electric Routine Maintenance/Repair Electric Shock Improper operation and maintenance Unplug electrical cord and retain control of plug during repair/maintenance Routine Operation Noise Equipment operation hearing protection Trauma Eye Injury Goggles or Safety glasses with side shield Hearing Protection Improper use, uncontrolled release of compressed air Projectiles, flying debris appropriate nozzle for specific work activity, situational awareness Goggles or safety glasses with side shields 4

5 Hazard Analysis: Battery Charger Foot Injury Drop object on foot Wear safety shoes Trauma (Burns) Batty acid spills Goggles, apron, gloves, proper battery handling procedures Eye Injury Battery acid splashes Goggles, appropriate battery handling procedures Electrical Shock Improper operation and maintenance, battery condition Lockout/tagout, manufacturer s instructions strictly followed Fire Sparks, improper storage of flammables, combustibles Appropriate placed fire extinguisher, remove all combustibles and fire hazards Explosion Spark/poor ventilation, smoking, improper procedures from machine area Adequate ventilation, no smoking, follow manufacturer s instructions Apron Gloves Safety Shoes/Boots Goggles 5

6 Hazard Analysis: Bench Grinder Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Trauma Projectiles Situational awareness, PPE, protective clothing, machine guards Foot Injury Drop object on foot Wear safety shoes Hand Injury Impact, penetration, Gloves, situational awareness compression Head Projectiles Face Shield Protection Fire Heat, sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from grinding/buffing area Electrical Shock Improper grounding, Improper operations and maintenance Lockout/tagout, proper grounding of frame, manufacturer s instructions strictly followed protective Clothing (optional) Goggles/Safety Glasses w/side shield Face Shield Safety Shoes/Boots disposable Respirators (optional) Gloves 6

7 Hazard Analysis: Chain Hoist Foot Injury Drop object on foot Wear Safety shoes Hand Injury Impact, burns Gloves, Situational awareness Head Swinging chain/hoisted Hard hat Protection equipment Gloves Safety Shoes/Boots Hard 7

8 Hazard Analysis: Chemicals (Pouring/Handling) Eye Injury Splash, fumes Goggles Contact irritation, burn or absorption Splash, skin contact Gloves (appropriate type for chemical), apron (if necessary), long sleeves Inhalation Breathing fumes Wear respirator if needed Face Splash Wear Face Shield (if necessary) Goggles Gloves protective Clothing (apron) Respirator (as needed) Face shield (if necessary) 8

9 Hazard Analysis: Cleaning (Sweeping/Mopping/Buffing) Trauma Projectiles, impact, chemical contact Situational awareness, gloves, protective clothing Foot Injury Dropped object on foot Wear safety shoes Inhalation Chemicals, dust Wear respirator or dust mask if needed Safety Shoes/boots Gloves (optional) protective Clothing (long pants recommended to prevent chemical splash on skin) Respirator or dust mask (as needed) 9

10 Hazard Analysis: Cutoff Saw Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators, automatic vacuum machine Eye Injury Projectiles Safety glasses with side shield Trauma Projectiles, rotating parts, point of operation, ingoing nip joints, flying chips & sparks Foot Injury Drop object on foot Safety shoes Hand Injury Point of Operation, ingoing nip points, rotating parts, flying chips and sparks or appropriate safety goggles Situational awareness, PPE, protective clothing, machine guards Machine guards, situational awareness Head Projectiles Face Shield Protection Fire Heat, sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper grounding, improper operations and maintenance Lockout/tagout, proper grounding of frame, manufacturer s instructions strictly followed Safety Shoes/Boots Safety glasses/goggles Face Shield (optional) disposable Respirators (optional) Hearing Protection 10

11 Hazard Analysis: Drill Bit Sharpener Eye Injury Projectiles, filings Safety glasses with side shield or appropriate safety goggles Hand Injury Point of operation, ingoing nip Situational awareness points, rotating parts, flying chips and sparks Electrical Shock Improper grounding, improper operations and maintenance Proper grounding of frame, manufacturer s instructions strictly followed Safety Glasses w/side shield 11

12 Hazard Analysis: Drill Press Inhalation Electrical Shock Sparks, friction Eye Injury Filings/particles generated during machine operation Improper grounding, improper operations and maintenance Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators Trauma Projectiles, flying sparks Safety glasses with side shield or appropriate safety goggles situational awareness Foot Injury Projectiles, rotating parts, point Wear safety shoes of operation, ingoing nip points, flying chips & sparks Hand Injury Drop object on foot Gloves (optional), machine Head Protection Point of operation, ingoing nip points, rotating parts, flying chips & sparks guards, situational awareness Face shield (if necessary) Fire Projectiles Proper grounding of frame, manufacturer s instructions strictly followed. Appropriate placed fire extinguisher, remove all combustibles and fire hazards Protective Clothing (optional) Safety Shoes/Boots Goggles/Safety Glasses w/side shield disposable Respirators (optional) Face shield Gloves (optional) 12

13 Hazard Analysis: Drum, Gal (Handling) Eye Injury Splashes Goggles (for handling exposed chemicals) Trauma Impact Situational awareness, gloves Foot Injury Dropped object on foot Wear safety shoes Goggles Safety Shoes/boots Gloves 13

14 Hazard Analysis: Floor Jack, Hydraulic Foot Injury Roll jack over foot Wear safety shoes Trauma Overloading jack beyond rated capacity, using jack for support rather than just lifting Follow manufacturer s instructions. Ensure that rated load is legibly and permanently marked in a prominent location on jack, and rated capacity is not exceeded. Immediately support load once it is lifted. Safety Shoes/Boots 14

15 Hazard Analysis: Forklift Trauma Projectiles, impact, vibration, burns Situational awareness, gloves, switch guards Foot Injury Dropped object on foot Wear safety shoes Noise Engine, impact Wear hearing protection Eye Fluid splash when servicing Wear safety goggles Safety goggles Safety Shoes/boots Hearing Protection Gloves 15

16 Hazard Analysis: Fuel Transfer Pump Eye Injury Fuel splashes Goggles Hand Injury Fire, Explosion Fuel contact in sub-zero weather Smoking, sparks, improper grounding and bonding Gloves No smoking or exposure to sparks or open flame during fueling. Fill stem shall be bonded to the container during filling operations by means of a bond wide. Appropriate placed fire extinguisher. Goggles Gloves 16

17 Hazard Analysis: Hand Held Portable Power Tools Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators (if necessary), automatic vacuum machine Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Foot Injury Drop object on foot Wear safety shoes Hand Injury Point of operation, ingoing nip points, rotating parts, flying chips & sparks Machine guards, situational awareness Head Projectiles Face Shield Protection Fire Sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from machine area Noise Machine operation Hearing protection Electrical Shock Improper grounding, improper operations and maintenance Proper grounding of frame, manufacturer s instructions strictly followed Protective Clothing (optional) Safety Shoes/Boots Goggles/Safety Glasses w/side shields Disposable Respirators (optional) Face shield, as appropriate Hearing Protection 17

18 Hazard Analysis: Heat Gun Inhalation Fumes, vapors and gases generated during use Properly ventilated work area, use disposable respirators Burns Hot air, contact with heat gun Situational awareness, gloves Electrical Shock Improper operation & maintenance Manufacturer s instructions strictly followed, replace worn parts Gloves disposable Respirators (optional, if appropriate) 18

19 Hazard Analysis: Hoist (Electric/Manual)/Slings Trauma Impact Situational awareness, gloves, hardhat Foot Injury Dropped object on foot Wear safety shoes Safety Shoes/boots Gloves Hard hat 19

20 Hazard Analysis: Hydraulic Press Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Trauma Projectiles, moving parts, point of operation, pinch points, flying items Situational awareness, PPE, protective clothing, machine guards Foot Injury Drop object on foot Wear safety shoes Hand Injury Point of operation, pinch points, moving parts, flying items. Head Protection Projectiles Gloves, machine guards, situational awareness Face Shield (as necessary) Protective Clothing (optional) Safety Shoes/Boots Goggles/Safety Glasses w/side shield Gloves Face shield (as necessary) 20

21 Hazard Analysis: Jack Stands, Manual Foot Injury Improper placement of load Situational awareness, wear safety shoes Trauma Overloading vehicle stand beyond rated capacity Follow manufacturer s instructions. Ensure that rated load is legibly and permanently marked in a prominent location on vehicle stand, and rated load capacity is not exceeded. Safety Shoes/Boots 21

22 Hazard Analysis: Lifting/Carrying Objects Trauma Impact Situational awareness, gloves, back brace/belt (optional) Foot Injury Dropped object on foot Wear safety shoes/boots Safety Shoes/boots Gloves Back brace/belt (optional) 22

23 Hazard Analysis: Miter Saw Inhalation Dust/particles generated during machine operation Appropriate natural ventilation, disposable respirators (if needed) Eye Injury Projectiles Safety glasses with side shield Trauma Projectiles, rotating parts, points of operation, ingoing nip points, flying chips & sparks or appropriate safety goggles Situational awareness, PPE, protective clothing, machine guards Foot Injury Drop object on foot Wear safety shoes Hand Injury Point of Operations, ingoing nip points, rotating parts, flying chips and sparks Machine guards, situational awareness Head Projectiles Face Shield (as necessary) Protection Fire Sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from machine area Electrical Shock Improper grounding, improper operation and maintenance Proper grounding of frame, manufacturer s instructions strictly followed Safety Shoes/Boots Goggles/Safety Glasses w/side shield Face Shield (as necessary) Disposable Respirators (if needed) 23

24 Hazard Analysis: Pallet Jack & Dolly, Hydraulic Foot Injury Roll jack over foot Wear safety shoes Trauma Overloading jack beyond rated capacity, using jack for support rather than just lifting, sharp objects Follow manufacturer s instructions, gloves Safety Shoes/Boots Gloves 24

25 Hazard Analysis: Portable Generator, Gasoline Powered Inhalation Exhaust Appropriate ventilation Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 25

26 Hazard Analysis: Portable Heater, Electric Powered Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 26

27 Hazard Analysis: Portable Heater, Gasoline Powered Inhalation Exhaust Appropriate ventilation Trauma Burns Situational awareness, PPE, protective clothing Foot Injury Roll over foot, drop object on Wear safety shoes foot Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Electrical Shock Improper operations and maintenance, improper switching device Strictly follow manufacturer s instructions, proper switching for starting up/ shutting down machine Leather Gloves Safety Shoes/ Boots 27

28 Hazard Analysis: Power Hacksaw Inhalation Dust/particles generated during machine operation, exhaust fumes Appropriate natural ventilation, respirators when needed Eye Injury Projectiles, burns Safety glasses with side shield or appropriate safety goggles Head Projectiles Face shield (as necessary) Protection Trauma Projectiles, point of operation, flying chips & sparks, improper use and operation Foot Injury Drop object on foot Safety shoes Hand Injury Point of operation, in-going nip points, rotating parts, flying chips and sparks Situational awareness, PPE, protective clothing, machine guards, manufacturer s instructions strictly followed Machine guards, situational awareness Fire Sparks Appropriate placed fire extinguisher, remove all combustibles and fire hazards from machine area Protective Clothing (optional) Safety Shoes/ Boots Goggles/Safety Glasses w/side shield Respirators (if needed) Face Shield (as necessary) 28

29 Hazard Analysis: Propane Torch (14oz to 20oz Propane Cylinder) Inhalation Eye Injury Hazardous fumes, gases, dusts Projectiles, fumes, dusts, flashes Appropriate natural or mechanical ventilation, and disposable respirators, as required Goggles, face shield, appropriate noncombustible or flame-proof screens Trauma Projectiles, burns Situational awareness, PPE Foot Injury Drop object on foot Wear safety shoes Fire Heat, sparks, slag Appropriate placed fire extinguisher, remove all combustibles and fire hazards from area Gloves Safety Shoes/Boots Goggles/Safety Glasses Respirator (if needed) Protective Clothing (optional) 29

30 Hazard Analysis: Shop Vac(s) Foot Injury Drop object on foot Wear safety shoes Electrical Shock Improper operations and maintenance, improper grounding Manufacturer s instructions strictly followed, proper grounding Eye Injury Flying debris Wear safety glasses w/side shields Noise Equipment Operation hearing protection PPE Required :( PPE required to be worn during the vacuuming task when it poses a specific hazard to the user) Safety Glasses with side shields Hearing Protection Safety Shoes/Boots 30

31 Hazard Analysis: Soldering Guns/Irons (HVAC) Inhalation Fumes, vapors and gases generated during soldering Properly ventilate work area, use respirator Eye Injury Spattering Safety glasses w/side shields/goggles Skin irritation/burning Chemical cleaner use, hot soldering iron Review MSDS, substitute cleaner with non-toxic product, use appropriate PPE/protective clothing Foot Injury Drop object on foot Wear safety shoes Fire Hot soldering iron Appropriate placed fire extinguisher, remove all combustibles and fire hazards from soldering area Electrical Shock Residual surface contamination Some fluxes contain toxic compounds (i.e. cadmium and fluorides) Improper operation and maintenance Soldering with lead containing solders Toxic compounds in fluxes Manufacturer s instructions strictly followed, replace worn parts Wipe down work area when finished Review MSDS, substitute with nontoxic compounds if available Safety glasses w/side shields/goggles Safety Shoes/Boots (for protection against dropped objects when necessary) Protective Clothing Respirators (when needed) 31

32 Hazard Analysis: Vise Eye Injury Projectiles Safety glasses with side shield or appropriate safety goggles Foot Injury Drop object on foot Wear safety shoes Hand Injury Impact, penetration, compression Gloves, situational awareness Goggles/ Safety Glasses w/ side shield Gloves Safety Shoes/Boots 32