Cellular Modem Installation Guide
|
|
|
- Chrystal O’Neal’
- 7 years ago
- Views:
Transcription
1 Cellular Modem Installation Guide This installation guide describes how to install and set up a GSM cellular modem for use as a communication gateway for the SolarEdge device (inverter or Safety and Monitoring Interface [SMI]). What s in the Box GenPro 20e SQB GSM modem GSM antenna Universal power supply 15-pin / 9-pin serial cable 15-pin to 3-wire (RXD,TXD and GND) serial cable Modem manufacturer instruction sheet This installation guide Physically Connecting the GSM Cellular Modem 1 Connect the antenna to the modem. 2 Remove the SIM card cover, insert a SIM card into the modem and put the SIM card cover back. NOTE: A SIM card is not supplied with this product. You must purchase a SIM card and an appropriate GPRS data package from your GSM service provider separately. Confirm with your GSM service provider that the SIM card is unlocked for GPRS data usage. For an inverter with an external RS232 port, continue to step 3. For other devices, continue to step 4. 3 When using a SolarEdge inverter, connect the modem to the inverter using the RS232 port. Use the 15-pin / 9-pin serial cable provided. The smallest hole is for RS232 cable insertion. The SolarEdge device glands come presealed from the factory. Remove the sealing to insert the cable. CAUTION: If a gland is opened and not used, then make sure to reseal it. Otherwise, it may degrade the device s ingress protection and void the warranty. CAUTION: The internal side of the gland includes an o-ring, which should be used to ensure proper sealing. 7 Connect the modem to the SolarEdge device through the RS232 connector, which is the nine-pin terminal block connector on the right side of the communication board. RS232 Connector Figure 1: Inverter RS232 Connection Continue to step 8. 4 When using a SolarEdge SMI or an inverter without an external RS232 port, be sure to turn the AC power off and wait five minutes. 5 Open the SolarEdge device cover, as instructed in the device manual. 6 Open gland #1 located on the bottom of the SolarEdge device, as shown in Figure 2. Figure 2 shows the SMI as an example. The procedure is similar for the inverter. Cable Gland Figure 2: Cable Gland Location on SMI Figure 3: GSM Cellular Modem Wire Connection The GSM kit comes with its dedicated cable. Locate the hole specified for RS232 cable and insert the side without connector of the RS232 cable into the device through the gland. Connect its wires as follows: Insert the Tx-marked wire into the terminal block TX pin. Insert the Rx-marked wire into the terminal block RX pin. Insert the G-marked wire into the terminal block G pin. 8 Connect the other side of the RS232 cable to the GSM modem. 9 Connect the power supply to the modem and to an electrical socket. G TX RX 1
2 Configuring the SolarEdge device using the user buttons: 1 Verify that the SolarEdge device s ON/OFF switch is OFF. 2 Press the LCD Light button once to turn ON the backlight. 3 WARNING! If the SolarEdge device worked properly before this action, the adjacent message is displayed. This message is displayed until the DC is below the safety voltage threshold. The default safety voltage is 50 V. Do not open the cover or open DC connectors until the voltage is indicated as safe or until at least five minutes have passed. 3 Short press the LCD button to scroll through the informative screens to show the ID status window and verify the CPU firmware version. Verify if it is below or above version I D : # # # # # # # # # # D S P 1 / 2 : / C P U : C o u n t r y : U S A 4 The following configuration procedures are performed with the SolarEdge device cover open. WARNING! Refer to the SolarEdge device manual for instructions about how to open the SolarEdge device cover. Four buttons for controlling the LCD panel menus are then accessible, as shown below: Esc: Goes to the beginning of the currently entered parameter or to the previous menu. Up (1): Goes up one option in a menu. Down (2): Goes down one option in a menu. Enter (3): Confirms the entry or selection of a parameter. Esc Up (1) Down (2) Enter (3) 5 Press the Enter button for at least five seconds. The following message is displayed: P l e a s e e n t e r P a s s w o r d * * * * * * * * Figure 4: LCD Panel Menu Buttons The SolarEdge device is now in Setup mode and all its LEDs are lit. The SolarEdge device automatically exits Setup mode if no buttons are pressed for more than two minutes. 6 Use the three right-most buttons inside the SolarEdge device (the UP-1, Down-2 and Enter-3 buttons), shown above, to type in the following default password: Scroll down to the Communication submenu and select it. For firmware versions above 2.250, continue to step 14. For earlier versions, complete steps 8 through 13 below. 8 Select the Server submenu, scroll down to the RS232 option and select it. The SolarEdge device performs a reset immediately after the selection is made. 9 Repeat steps 5 through 7 to enter Setup mode. 2
3 10 Scroll down to the RS232 Conf submenu and select it. S e r v e r < L A N > R S C o n f < S > > 11 In the RS232 Conf submenu, select Set Mode and then select GSM. The SolarEdge device performs a reset immediately after the selection is made. 12 Repeat steps 5 through 7 to enter Setup mode. 13 Scroll down to the RS232 Conf submenu and select it. Follow steps 14 through 20 for firmware versions above For earlier versions, complete steps 17 through 20 below. 14 Select the Server submenu, scroll down to the RS232 option and select it. 15 Scroll down to the RS232 Conf submenu and select it. 16 In the RS232 Conf submenu, select Protocol and then select GSM Modem. 17 In the RS232 Conf submenu, select Set Modem Type and then select SE GSEG-20E GSM. 18 In the RS232 Conf submenu, select Set APN and enter your GSM service provider s Access Point Name (APN). This network address can be obtained by calling your service provider. Press the Enter button for a long press to apply or press the ESC button for a long press to abort. 19 In the RS232 Conf submenu, select Set User Name and enter the user name, if required by the GSM service provider. Press the Enter button for a long press to apply, or press the ESC button for a long press to abort. 20 In the RS232 Conf submenu, select Set Password and then enter the password, if required by the GSM service provider. Press the Enter button for a long press to apply or press the ESC button for a long press to abort. Verifying the Connection To verify the connection: 1 Wait for the SolarEdge device to connect to the SolarEdge Monitoring Server. This may take up to two minutes. 2 Verify that the LCD panel displays a window similar to the following: V a c [ v ] V d c [ v ] P a c [ w ] V 0. 0 < S _ O K > O F F S_OK: Verify that S_OK appears on the panel to indicate a functioning connection to the SolarEdge Monitoring Server, which was validated during the last two minutes. NOTE: If the S_OK indication is not displayed, then perform the following: Use another method (unrelated to the SolarEdge device) to check whether the network and modem are operating properly. For example, connect a laptop to the Ethernet modem and connect to the Internet. Check the Server Communication status screen by short pressing the LCD button. If the Modem Disconnected message (appears only in firmware version and above) is displayed, verify the physical connection between the modem and the SolarEdge device or reset the GSM modem. Check the Server Communication status screen by short pressing the LCD button. If the Absent or Locked SIM message is displayed, check that the SIM card is fully inserted in the right direction. Verify with your GSM network provider that the SIM card is not locked for GPRS data usage. Verify that there is cellular reception near the GSM modem. Check the configuration of the SolarEdge device. 3
4 Appendix A Multiple SolarEdge Devices, RS485 Bus and GSM Modem Connection This configuration enables you to connect multiple SolarEdge devices through the same bus in a master/slave configuration. In this configuration, only the master is physically connected to the Internet through the GSM modem. Recommended Cable Type and Distance: RS232: Cable Type: Supplied with kit. Max. Distance: 15 m / 50 ft (supplied cable plus extension). RS485: Cable Type: Four-conductor cable (with RJ11 connectors for older communication board versions). Max. Distance: 1,000 m / 3,000 ft (from the master SolarEdge device). Figure 5: Connecting Multiple SolarEdge devices Additional Required Equipment: Four-conductor cable (not supplied by SolarEdge). This section assumes that GSM modem communication is already configured, as described above. RS485 bus terminations: The two SolarEdge devices at the ends of the chain (meaning the first SolarEdge device and the last SolarEdge device) must be terminated by switching a termination dip-switch inside the SolarEdge device to ON. The switch is marked SW7, as shown in Figure 6. Use the left switch Configuring the SolarEdge devices using the user buttons: 1 First, configure the GSM cellular modem connection, as described above. For each of the slave SolarEdge devices, perform the remaining steps in this procedure. 2 Verify that the SolarEdge device s ON/OFF switch is OFF. 3 Press the LCD Light button once to turn ON the backlight. WARNING! 4 Short press the LCD button to scroll through the informative screens to show the ID status window and verify the CPU firmware version. Verify whether it is below or above version I D : # # # # # # # # # # D S P 1 / 2 : / C P U : C o u n t r y : U S A 5 The following configuration procedures are performed with the SolarEdge device cover open. Four buttons for controlling the LCD panel menus are then accessible, as shown in Figure 4. Esc: Goes to the beginning of the currently entered parameter or to the previous menu. Up (1): Goes up one option in a menu. Figure 6: RS485 Termination Switch If the SolarEdge device worked properly before this action, the adjacent message is displayed. This message is displayed until the DC is safe. The default safety voltage is 50 V. Do not open the cover or open DC connectors until the voltage is indicated as safe or until at least five minutes have passed. Down (2): Goes down one option in a menu. Enter (3): Confirms the entry or selection of a parameter. 6 Press the Enter button for at least five seconds. The following message is displayed: P l e a s e e n t e r P a s s w o r d * * * * * * * * The SolarEdge device is now in Setup mode and all its LEDs are lit. The SolarEdge device automatically exits Setup mode if no buttons are pressed for more than two minutes. 4
5 7 Use the three right-most buttons inside the SolarEdge device (the UP-1, Down-2 and Enter-3 buttons), shown above, to type in the following default password: For firmware versions above 2.250, continue to step 12. For earlier versions, complete steps 9 through 11 below. 8 Scroll down to the Communication submenu and select it. 9 Select the Bus submenu. Scroll down and select RS485 Slave. The SolarEdge device performs a reset immediately after the selection is made. Bus Submenu: Z i g b e e P 2 P Z i g b e e M P R S M a s t e r > R S S l a v e N o n e 10 Repeat steps 6 through 8 above to enter Setup mode. 11 Select the Server submenu, scroll down to the RS485 option and select it. The SolarEdge device performs a reset immediately after the selection is made. > S e r v e r < L A N > R S C o n f < S > This concludes the setting of the slave SolarEdge devices for firmware versions earlier than Follow steps 12 through 16 for firmware versions above Select the Server submenu, scroll down to the RS485 option and select it. > S e r v e r < L A N > R S C o n f < S > R S C o n f < S > Z I G B E E C o n f < S > 13 Select the RS485-X Conf (the port that is physically connected to the daisy chain) submenu option. 14 Select the Device Type submenu and set it to SolarEdge. RS485-X Submenu: > D e v i c e T y p e < S E > P r o t o c o l < M > D e v i c e I D < 1 > S l a v e D e t e c t 15 Select the Protocol submenu and set it to Slave. 16 Press the ESC button repeatedly to exit the Setup menu or wait for the device to automatically exit Setup mode if no buttons are pressed for more than two minutes. This concludes the slave device configuration using the LCD button for firmware version and above For the master (main) SolarEdge device, perform the following steps: 1 Repeat steps 2 through 8, as described above in the Slave Configuration section to enter Setup mode. For firmware versions above 2.250, continue to step 7. For earlier versions, complete steps 2 through 6 below. 2 Select the Bus submenu. Scroll down and select RS485 Master. The SolarEdge device performs a reset immediately after the selection is made. Bus Submenu: Z i g b e e P 2 P Z i g b e e M P > R S M a s t e r R S S l a v e N o n e 3 Repeat steps 6 through 8 above in the Slave Configuration section to enter Setup mode. 4 Scroll down to the RS485 Conf submenu and select it. Select the Master Set option and select Enable. The SolarEdge device performs a reset immediately after the selection is made. S e r v e r < L A N > > R S C o n f < S > 5 Repeat steps 6 through 8 as described above in the Slave Configuration section to enter Setup mode. 6 Scroll down to the RS485 Conf submenu and select it. S e r v e r < L A N > > R S C o n f < S > 5
6 Follow steps 7 through 11 for firmware versions above For earlier versions, complete steps 10 through 11 below. 7 Select the RS485-X Conf (the port that is physically connected to the daisy chain) submenu option. 8 Select the Device Type submenu and set it to SolarEdge. RS485-X Submenu: > D e v i c e T y p e < S E > P r o t o c o l < M > D e v i c e I D < 1 > S l a v e D e t e c t 9 Select the Protocol submenu and set it to Master. 10 Select the Slave Detect option and select Yes. A Detecting Slaves message is shown during the detection process. The master should report the correct number of slaves on the LCD screen. If it does not, verify the connections and terminations. 11 Press the ESC button repeatedly to exit the Setup menu. This concludes the multi-solaredge device setup using the user buttons. Support and Contact Information If you have technical questions concerning our products, please contact us: USA & Canada: Germany: Italy: (Free Local Number) France: (Free Local Number) United Kingdom: (Free Local Number) Rest of the world: +1 (650) Fax: to: support@solaredge.com 6
Setting Up the ZigBee Ethernet Gateway
Setting Up the ZigBee Ethernet Gateway MAN-01-00030-1.4 This manual describes how to install and set up ZigBee communication between a SolarEdge device (Inverters or Safety and Monitoring Interface) and
Communication Setup Application Note
Communication Setup Application Note This Application Note describes how to install and set up communication between the inverter and the SolarEdge Monitoring Server. This document contains the following
SolarEdge. RS485 Expansion Kit Installation Guide. Version 1.0
SolarEdge RS485 Expansion Kit Installation Guide Version 1.0 Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in
Application Note - Connecting an Electricity Meter to SolarEdge Devices (Europe and APAC)
February 2015 February 2015 Application Note - Connecting an Electricity Meter to SolarEdge Devices (Europe and APAC) This document describes how to connect an electricity meter to a SolarEdge device (inverters,
Disclaimers. Important Notice
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
Contents Chapter 1: Introduction... 3 Chapter 2: Ethernet (LAN)... 5 Chapter 3: ZigBee Wireless Connection Options... 7
Contents Chapter 1: Introduction... 3 Communication Types and Functionality... 3 Communication Connectors... 3 Communication Lightning Protection... 4 Chapter 2: Ethernet (LAN)... 5 Single/Multiple Devices,
Disclaimers. Important Notice
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means,
About This Guide SolarEdge Configuration Tool Software Guide. About This Guide
About This Guide 3 About This Guide This user guide is intended for Photovoltaic (PV) system owners, installers, technicians, maintainers, administrators and integrators who are authorized to configure
About This Guide SolarEdge Configuration Tool Software Guide. About This Guide
Version 2.0 About This Guide 2 About This Guide This user guide is intended for Photovoltaic (PV) system owners, installers, technicians, maintainers, administrators, and integrators who are authorized
Disclaimers. Important Notice. Exclusion of Liability. FCC Compliance. Disclaimers
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
SolarEdge Export Limitation Guide
SolarEdge Export Limitation Guide Europe and APAC Version 2.0 Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in
How To Set Up An Inverter
MAKING MODERN LIVING POSSIBLE SOLAR INVERTERS Installation Guide GSM Option Kit FLX series www.danfoss.com/solar Safety Safety Safety Message Types WARNING Safety information important for human safety.
RouteFinder SOHO. Quick Start Guide. SOHO Security Appliance. EDGE Models RF825-E, RF825-E-AP CDMA Models RF825-C-Nx, RF825-C-Nx-AP
RouteFinder SOHO SOHO Security Appliance EDGE Models RF825-E, RF825-E-AP CDMA Models RF825-C-Nx, RF825-C-Nx-AP Quick Start Guide RouteFinder RF825 Series Quick Start Guide RouteFinder SOHO Security Appliance
Chapter 1 Connecting the Router to the Internet
Chapter 1 Connecting the Router to the Internet This chapter describes how to set up the router on your Local Area Network (LAN) and connect to the Internet. It describes how to set up your wireless ADSL
Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2. Instruction Manual
Firmware version: 1.10 Issue: 7 AUTODIALER GD30.2 Instruction Manual Firmware version: 2.0.1 Issue: 0.6 Version of the GPRS transmitters configurator: 1.3.6.3 Date of issue: 07.03.2012 TABLE OF CONTENTS
NETCOMM LIBERTY SERIES. 3G WiFi Router. Quick Start Guide
NETCOMM LIBERTY SERIES 3G WiFi Router Quick Start Guide Connecting to the Router using 1an Ethernet cable SIM Card Computer 1. Insert an active 3G SIM card into the USIM slot on the back of the device.
Rev 06 1211. GSM base station. Installation instructions
Rev 06 1211 GSM base station Installation instructions Output string format Baud rate 115200 bps Parity none Data bits 8 Stop bits 1 Flow control none The output string is a modified version of the Sureguard
SolarEdge Installation Guide MAN-01-00057-2.1. Cover goes here (right-side [odd] page)
![SolarEdge Installation Guide MAN-01-00057-2.1. Cover goes here (right-side [odd] page)](/thumbs/26/9028191.jpg "SolarEdge Installation Guide MAN-01-00057-2.1. Cover goes here (right-side [odd] page)")
1 Cover goes here (right-side [odd] page) Disclaimers 2 Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system
Troubleshooting and Diagnostics
Troubleshooting and Diagnostics The troubleshooting and diagnostics guide provides instructions to assist in tracking down the source of many basic controller installation problems. If there is a problem
SMS Alarm Messenger. Setup Software Guide. SMSPro_Setup. Revision 090210 [Version 2.2]
![SMS Alarm Messenger. Setup Software Guide. SMSPro_Setup. Revision 090210 [Version 2.2]](/thumbs/29/13662687.jpg "SMS Alarm Messenger. Setup Software Guide. SMSPro_Setup. Revision 090210 [Version 2.2]")
SMS Alarm Messenger SMSPro_Setup Revision 090210 [Version 2.2] ~ 1 ~ Contents 1. How to setup SMS Alarm Messenger?... 3 2. Install the SMSPro_Setup software... 5 3. Connection Type... 6 4. Connection Port
P-660HNU-Tx. Wireless N ADSL2+ 4-port Gateway DEFAULT LOGIN DETAILS. Firmware v1.02 Edition 1, 11/2011. IP Address: http://192.168.1.1.
P-660HNU-Tx Wireless N ADSL2+ 4-port Gateway with USB Firmware v1.02 Edition 1, 11/2011 DEFAULT LOGIN DETAILS IP Address: http://192.168.1.1 User: admin Password: 1234 www.zyxel.com Copyright 2011 ZyXEL
JDSU PathTrak. HCU200 Install User s Guide
JDSU PathTrak HCU200 Install User s Guide Notice Copyright System Requirements The information contained in this document is the sole property of JDSU and may not be reproduced, copied, or communicated
PowerLogic Sub Meter Display (SMD and SMDOPN)
Instruction Bulletin Z203742-0B PowerLogic Sub Display (SMD and SMDOPN) CONTENTS Introduction... 2 Parts of the Sub Display... 3 Dimensional Drawing... 4 Installation... 5 Mounting the SMD... 5 Mounting
Installation Guide Solar Connect-11
Installation Guide Solar Connect-11 Version 1.1 Contents Important Product Information 3 System Registration Form 4 Solar Connect-11 Overview 5 Internet & Power Connections 6 Single Phase CT Connections
If you are unable to set up your Linksys Router by using one of the above options, use the steps below to manually configure your router.
This article describes how to manually configure a Linksys Router for broadband DSL that uses PPPoE (Point-to-Point Protocol over Ethernet) for authentication. For automatic configuration options, please
omega.com ΩOMEGA RS232 Multi-Drop www.omega.com FMA1600-MDB Multi-Drop Box
omega.com ΩOMEGA RS232 Multi-Drop www.omega.com FMA1600-MDB Multi-Drop Box 1 3/29/2010 Rev.0 DOC-OMEGABB9MAN 2 Introduction FMA1600-MDB Multi-Drop Box Operating Bulletin The FMA1600-MDB Multi-Drop Box
BlueSolar Pro Remote Panel For BlueSolar PWM-Pro charge controllers 12/24V 5, 10, 20, 30A Article number SCC900300000
Manual EN BlueSolar Pro Remote Panel For BlueSolar PWM-Pro charge controllers 12/24V 5, 10, 20, 30A Article number SCC900300000 Contents EN 1.Important safety instructions... 2 2. Installation... 2 3.Product
SwitchView 1000 Switch. Installer/User Guide
SwitchView 1000 Switch Installer/User Guide SwitchView 1000 Switch Installer/User Guide Avocent, the Avocent logo, The Power of Being There and SwitchView are registered trademarks of Avocent Corporation.
Supplemental User Guide
Supplemental User Guide SUPPLEMENTAL GUIDE FOR UPDATG FIRMWARE ON Z-MAX TM LIGHTG CONTROL RELAY PANELS WITH MASTER CONTROL MODULE Software revision.00 an up LIT-ZMAXS-00 Rev A, August 2004 Technical Services:
3NNet KVM CP-104S /OSD / 19 KVM CP-108S / OSD / 19 KVM CP-116S / OSD / 19
3NNet USERS MANUAL KVM CP-104S /OSD / 19 KVM CP-108S / OSD / 19 KVM CP-116S / OSD / 19 RACK MOUNTABLE 4 / 8 / 16 PORT PS2 KVM SWITCH Rev 1.1 TABLE OF CONTENTS INTRODUCTION.. 3 FEATURES... 3 PACKAGE CONTENTS........
USER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6
KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly
* DISCLAIMER: Contents. How to Use This Guide: COMMERCIAL INSTALL GUIDE 2
COMMERCIAL INSTALL GUIDE 2 Contents How to Use This Guide: The first section of this guide is designed to assist you with the installation of your DECK Monitoring hardware. The revenue grade meter and
Secure Ethernet Gateway SEG-1 and SEG-M for IEI Access Systems Installation Manual
Secure Ethernet Gateway SEG-1 and SEG-M for IEI Access Systems Installation Manual Section 1: Introduction SECURITY WARNING: New SEG's shipped after April 2008 will have Telnet setup option enabled by
BIT COMMANDER. Serial RS232 / RS485 to Ethernet Converter
BIT COMMANDER Serial RS232 / RS485 to Ethernet Converter (Part US2000A) Copyrights U.S. Converters 1 Contents Overview and Features... 3 Functions..5 TCP Server Mode... 5 Httpd Client Mode.5 TCP Auto mode....6
Router Setup Manual. NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 208-10060-01 2006-03-17
NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA 208-10060-01 2006-03-17 2006 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR is a trademark of Netgear, Inc. Microsoft, Windows,
PRORAE REMOTE HOST CONTROLLER: COMMUNICATION TROUBLESHOOTING GUIDE
PRORAE REMOTE HOST CONTROLLER: COMMUNICATION TROUBLESHOOTING GUIDE INTRODUCTION This technical note provides simple procedures that can be performed in the field to help identify and correct the cause
www.digi.com/support June 2013 v. 0.2
Application Note Verizon LTE Provisioning on Digi TransPort www.digi.com/support June 2013 v. 0.2 Page 1 of 7 Contents 1 Introduction... 2 1.1 Purpose... 2 1.2 Necessary Documents / Tools... 2 1.3 Assumptions
CelluLine CGW-TS GSM Cellular Gateway. Installation and Programming Manual
CelluLine CGW-TS GSM Cellular Gateway Installation and Programming Manual CelluLine CGW-TS GSM Cellular Gateway Installation and Programming Manual CGWTS-M001A Version 1, Release 1, December 2004 NOTICE
User manual Compact Web PLC WP240 series IEC-line
User manual Compact Web PLC WP240 series IEC-line update: 09-01-2014 IEC-line by OVERDIGIT overdigit.com 1. General description The WP240 device is a PLC, programmable in IEC61131-3 language using CoDeSys
NC-12 Modbus Application
NC-12 Modbus Application NC-12 1 Table of Contents 1 Table of Contents... 2 2 Glossary... 3 SCADA...3 3 NC-12 Modbus in general... 3 4 Entire system... 4 4.1 PFC to PC connection alternatives...4 4.1.1
P-660HW-Tx v3. 802.11g Wireless ADSL2+ 4-port Gateway DEFAULT LOGIN DETAILS. Firmware v3.70 Edition 1, 2/2009
P-660HW-Tx v3 802.11g Wireless ADSL2+ 4-port Gateway Firmware v3.70 Edition 1, 2/2009 DEFAULT LOGIN DETAILS IP Address: http://192.168.1.1 Admin Password: 1234 User Password: user www.zyxel.com Copyright
Check Your Package Contents. CD-ROM containing Manual and Warranty
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DVA-G3340S Wireless VoIP Router Before You Begin If you purchased this Router to share your
Ethernet Radio Configuration Guide
Ethernet Radio Configuration Guide for Gateway, Endpoint, and Repeater Radio Units April 20, 2015 Customer Service 1-866-294-5847 Baseline Inc. www.baselinesystems.com Phone 208-323-1634 FAX 208-323-1834
Different Ways of Connecting to. 3DLevelScanner II. A.P.M Automation Solutions LTD. www.apm-solutions.com Version 3.0
3DLevelScanner II Different Ways of Connecting to 3DLevelScanner II A.P.M Automation Solutions LTD. www.apm-solutions.com Version 3.0 2 Different Ways of Connecting to 3DLevelScanner II Version 3.0 Table
User Manual. EtherUSB
User Manual EtherUSB USB Ethernet Access Point for PDA V 2.0 Clarinet Systems, Inc. Clarinet Systems, Inc. http://www.clarinetsys.com Page 1 Publication Revision No. Control Table Rev. No. Date Contents
Get to Know Your Device 4G LTE BROADBAND ROUTER WITH VOICE
Get to Know Your Device 4G LTE BROADBAND ROUTER WITH VOICE FRONT VIEW The Verizon 4G LTE Broadband Router with Voice is a wireless device that delivers Internet connectivity and telephone service. You
Disclaimers. Important Notice. Emission Compliance. Disclaimers
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
Chapter 1 Installing the Gateway
Chapter 1 Installing the Gateway This chapter describes how to set up the wireless voice gateway on your Local Area Network (LAN), connect to the Internet, and perform basic configuration. For information
Disclaimers. Important Notice. Emission Compliance. Disclaimers
Disclaimers Disclaimers Important Notice Copyright SolarEdge Inc. All rights reserved. No part of this document may be reproduced, stored in a retrieval system or transmitted, in any form or by any means,
Adding or replacing a mesh node in an existing mesh network
Adding or replacing a mesh node in an existing mesh network Use this procedure to add or replace a in an existing mesh For this procedure to work all nodes running the same firmware version. Before you
Energy Communication Unit (ECU)
Altenergy Power System Energy Communication Unit (ECU) Installation and User Manual (For ECU-3 V3.8) ALTENERGY POWER SYSTEM INC. All rights reserved TABLE OF CONTENTS 1.0 Introduction... 2 2.0 Installation...
Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000
Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000 1.0 Introduction A Technical Application Note from Doppler System July 5, 1999 Version 3.x of the DDF6000, running version
WRE6505. User s Guide. Quick Start Guide. Wireless AC750 Range Extender. Default Login Details. Version 1.00 Edition 1, 4 2014
WRE6505 Wireless AC750 Range Extender Version 1.00 Edition 1, 4 2014 2.4G 5G Quick Start Guide User s Guide Default Login Details LAN IP Address 192.168.1.2 User Name admin www.zyxel.com Password 1234
GSM Door Phone System
GSM Door Phone System System Installation, Setting and Operation Manual User Manual (263-S V1) Please read this user manual completely before operating this system and keep it in a safe place for future
TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL
TCP/IP MODULE CA-ETHR-A INSTALLATION MANUAL w w w. c d v g r o u p. c o m CA-ETHR-A: TCP/IP Module Installation Manual Page Table of Contents Introduction...5 Hardware Components... 6 Technical Specifications...
GSM Autodialer Professional GJD700 Speech & Text Autodialer
Text Edit message GSM Autodialer Professional GJD700 Speech & Text Autodialer Introduction The GSM Autodialer Professional works in conjunction with standard alarm systems and makes use of your preferred
Starting Guide - Poseidon 3265 First steps for remote monitoring with Poseidon & GSM
Poseidon 3265 starting guide Poseidon 3265 Starting Guide - Poseidon 3265 First steps for remote monitoring with Poseidon & GSM 1) Connecting Poseidon 3265 1.1) Check DIP switches settings. For installation
SCREENLOGIC INTERFACE WIRELESS CONNECTION KIT
SCREENLOGIC INTERFACE WIRELESS CONNECTION KIT FOR INTELLITOUCH AND EASYTOUCH CONTROL SYSTEMS INSTALLATION GUIDE IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS SAVE THESE INSTRUCTIONS Technical
IRIS Touch 600 Range Dialler Installation Manual. Version 1.3
IRIS Touch 600 Range Dialler Installation Manual Version 1.3 The information contained is supplied without liability for any errors or omissions. No part may be reproduced or used except as authorised
IP Indoor High Speed Dome. CAM-6500 series. Ver. 070307. Quick Installation Guide
IP Indoor High Speed Dome CAM-6500 series Ver. 070307 Quick Installation Guide 1 1 Getting Started 1.1 PACKAGE CONTENTS CAM-6500 series Warranty Card Software CD Power & A/V Cable LAN/WAN Cable Alarm Cable
New GSM Alarm System. User s Manual. Profile For a better understanding of this product, please read this user manual thoroughly before using it.
New GSM Alarm System User s Manual Profile For a better understanding of this product, please read this user manual thoroughly before using it. Chapter 1. Features Chapter 2. Alarm Host Introduction Chapter
Options for ABB drives, converters and inverters. User s manual FDPI-02 diagnostics and panel interface
Options for ABB drives, converters and inverters User s manual FDPI-02 diagnostics and panel interface Table of contents Table of contents 3 1. FDPI-02 diagnostics and panel interface Safety..............................................
Bluetooth to Serial Adapter
Bluetooth to Serial Adapter Third Edition, Oct 2007 Version 3.0 771-BTS1009C3-001 Contents 1.0 Features....P.2 2.0 Package Content....P.2 3.0 Hard Drives Requirement.P.2 4.0 Specifications.P.3 5.0 Pin
PCS300 Universal IP Reporting Module V1.0
PCS300 Universal IP Reporting Module V1.0 Reference and Installation Manual Patents: One or more of the following US patents may apply: 7046142, 6215399, 6111256, 6104319, 5920259, 5886632, 5721542, 5287111,
SNMP-1 Configuration Guide
SNMP-1 Configuration Guide You must configure the Net Logic Card before it can operate properly. You have two methods to configure the Net Logic Card: Using telnet or terminal. Using Telnet 1. Make sure
BEC 6200WZL. 4G/LTE Cellular Broadband Router. Quick Start Guide
BEC 6200WZL 4G/LTE Cellular Broadband Router Quick Start Guide 1 BEC 6200WZL 4G/LTE Cellular Broadband Router PLEASE READ THE QUICK START GUIDE AND FOLLOW THE STEPS CAREFULLY. THIS QUICK START GUIDE WILL
HP Advanced Wireless Docking Station. User Guide
HP Advanced Wireless Docking Station User Guide Copyright 2014, 2015 Hewlett-Packard Development Company, L.P. Intel is a trademark of Intel Corporation in the U.S. and other countries. Windows and Windows
Remote Monitoring of Woodward easygen-3000
Remote Monitoring of Woodward easygen-3000 HMS Industrial Networks AB Page 1 (22) About this Document HMS application notes are not binding and do not claim to be complete in regard to configuration and
HWg-STE HWg-STE PoE MANUAL
HWg-STE HWg-STE PoE MANUAL www.hw-group.com Page 2 HWg-STE connectors LED indicators Green: Power & Mode Yellow: Link & Activity SENSORS S1 and S2 ports for connecting temperature or humidity sensors.
510 / 511 Cardiorespiratory Monitor Preventative Maintenance Test Procedure
CAS MEDICAL SYSTEMS, INC. 510 / 511 Cardiorespiratory Monitor Preventative Maintenance Test Procedure using the 2301Multi-Function Tester 44 East Industrial Road Branford, CT 06405 USA www.techsrv@casmed.com
DWL-2000AP. Before You Begin. Check Your Package Contents
This product can be set up using any current web browser, i.e., Internet Explorer 6 or Netscape Navigator 6.2.3. DWL-2000AP D-Link AirPlus Xtreme G TM Wireless Access Point Before You Begin It s best to
INTELLIGENT CONTROL MODULE SA-2000-II HARDWARE MANUAL. Access Technologies International, Inc.
SA-2000-II HARDWARE MANUAL Access Technologies International, Inc. 1 Table of Contents 1. Introduction 3 2. Features 3 3. Specification 4 4. Identifying Supplied Parts 4 5. Panel Description 5 6. Connection
Back-UPS Pro 1300/1500 Installation and Operation
Back-UPS Pro 1300/1500 Installation and Operation Inventory Safety Do not install the Back-UPS in direct sunlight, in excessive heat, humidity, or in contact with fluids. Connect the battery bu059a bu058a
FOR MORE INFORMATION. 125 8880 or from a non-telstra phone 13 2200 and say pre-paid telstra.com/ppmbb visit a telstra store or partner
FOR MORE INFORMATION 125 8880 or from a non-telstra phone 13 2200 and say pre-paid telstra.com/ppmbb visit a telstra store or partner getting to know your telstra pre-paid 4G WI-FI (760S) LET S GET THIS
Quick Installation Guide DSL-2750U/NRU. 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch
DSL-2750U/NRU 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch BEFORE YOU BEGIN Delivery Package Router DSL-2750U/NRU Power adapter RJ-11 telephone cable Straight-through Ethernet cable (CAT 5E)
NETGEAR Trek N300 Travel Router and Range Extender
NETGEAR Trek N300 Travel Router and Range Extender PR2000 Installation Guide NETGEAR Reset /LAN LAN Contents Get Started........................................... 3 Connect on the Go..................................
Voice Over Internet Protocol (VoIP) Configuration
(VoIP) Configuration ENGINEERING REPORT No: 02-003 Introduction This report describes interfacing the IPCS VoIP Gateway Model EGW-902 to an ESTeem Model 192E Wireless Ethernet radio modem in a demonstration
To perform Ethernet setup and communication verification, first perform RS232 setup and communication verification:
PURPOSE Verify that communication is established for the following products programming option (488.2 compliant, SCPI only): DCS - M9C & DCS M130, DLM M9E & DLM-M9G & DLM M130, DHP - M9D, P series, SG,
Wi-Fi Setup Guide USING YOUR DMX PROFUSION is FOR
Wi-Fi Setup Guide USING YOUR DMX PROFUSION is FOR ProFusion is CUSTOMER SUPPORT 800 345.5000 TM MOOD: ProFusion is Pandora WI-FI SETUP GUIDE Connecting ProFusion is to Your WiFi Network Follow the instructions
GSM AD05 Slave GSM Auto Dialer- Instruction Manual
GSM AD05 Slave GSM Auto Dialer- Instruction Manual Please read these instructions before you start the installation Features LCD display Programmable 9 x 32 digit phone numbers for each trigger. 10 second
Quick Installation Guide DSL-2750U. 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch
DSL-2750U 3G/ADSL/Ethernet Router with Wi-Fi and Built-in Switch BEFORE YOU BEGIN Delivery Package Router DSL-2750U Power adapter DC 12V/1A RJ-11 telephone cable Ethernet cable (CAT 5E) Splitter (brochure).
The GV-I/O Box 8 Ports provides 8 inputs and 8 relay outputs, and supports both DC and AC output voltages.
GV-I/O Box 8 Ports The GV-I/O Box 8 Ports provides 8 inputs and 8 relay outputs, and supports both DC and AC output voltages. Key Features 8 inputs and 8 outputs are provided. Up to 9 pieces of GV-I/O
NETVIGATOR Wireless Modem Setup Guide. (TG789Pvn)
NETVIGATOR Wireless Modem Setup Guide (TG789Pvn) Configure the NETVIGATOR Wireless Modem Make sure that system meets the following requirement prior to NETVIGATOR Wireless Modem usage: - Subscribers who
GSM HOME SECURITY SYSTEM
Cell /Mobile phone home security system GSM HOME SECURITY SYSTEM Model : GSM-120 TABLE OF CONTENTS 1. FEATURES... 1 2. APPLICATION... 2 3. SPECIFICATIONS... 3 4. FRONT PANEL & LAYOUT DESCRIPTION...6 5.
125 8880 telstra.com/ppmbb visit a telstra store or partner GETTING TO KNOW YOUR
FOR MORE INFORMATIoN: 125 8880 telstra.com/ppmbb visit a telstra store or partner GETTING TO KNOW YOUR Telstra PRE-paid 4G wi-fi LET S GET THIS SHOW ON THE ROad WHAT S INSIDE Your Telstra Pre-Paid 4G Wi-Fi
Changing printer settings 1
Changing printer settings 1 You can change your printer setting by using your application software, your Lexmark printer driver, the printer operator panel, or the remote operator panel available from
AC-115 Compact Networked Single Door Controller. Installation and User Manual
AC-115 Compact Networked Single Controller Installation and User Manual December 2007 Table of Contents Table of Contents 1. Introduction...5 1.1 Key Features... 6 1.2 Technical Specifications... 7 2.
Crow Limited Warranty. Print Version 017
Crow Limited Warranty (Crow) warrants this product to be free from defects in materials and workmanship under normal use and service for a period of one year from the last day of the week and year whose
AutoWAVE. Programming Instructions P/N 1-0479-014. Part of Thermo Fisher Scientific. Revision D
AutoWAVE Programming Instructions P/N 1-0479-014 Revision D Part of Thermo Fisher Scientific AutoWAVE Programming Instructions P/N 1-0479-014 Revision D 2007 Thermo Fisher Scientific Inc. All rights
Welch Allyn Vital Signs Monitor 300 Series
Welch Allyn Vital Signs Monitor 300 Series Upgrade Installation Guide Vital Signs Monitor 300 Series Service Utility Tool Version 2.0.0 ii Welch Allyn Vital Signs Monitor 300 Series Copyright 2007, Welch
Connecting to the Internet
Connecting to the Internet Connecting the Gateway to the Internet Configuration of TCP/IP Protocol Installing the USB Drivers Connecting Ethernet Network Devices Connecting USB Network Devices Connecting
USER S MANUAL. Settop Cell-Xtrem
USER S MANUAL Settop Cell-Xtrem Rev. March 2014 USER S MANUAL 2 Index USER S MANUAL... 1 Settop Cell-Xtrem... 3 Become familiar with the Settop Cell-Xtrem... 4 Become familiar with the Settop Cell-Xtrem
B890 4G LTE Smart Hub Getting Started Guide
B890 4G LTE Smart Hub Getting Started Guide HUAWEI TECHNOLOGIES CO., LTD. Thank You for Purchasing the B890 4G LTE Smart Hub! Before You Begin What s in the Box : 1. B890 4G LTE Smart Hub 2. Power adapter
User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M)
Document code: MN67038-2_ENG Revision 1.400 Page 1 of 25 User Manual Revision 1.400 English Converter / Adapter Ethernet to RS232 / RS485 (Order Code: HD67038-2 HD67038-2-M HD67038-25 HD67038-25-M) for
Taurus Super-S3 LCM. Dual-Bay RAID Storage Enclosure for two 3.5-inch Serial ATA Hard Drives. User Manual March 31, 2014 v1.2 www.akitio.
Dual-Bay RAID Storage Enclosure for two 3.5-inch Serial ATA Hard Drives User Manual March 31, 2014 v1.2 www.akitio.com EN Table of Contents Table of Contents 1 Introduction... 1 1.1 Technical Specifications...
ProSAFE 8-Port and 16-Port Gigabit Click Switch
ProSAFE 8-Port and 16-Port Gigabit Click Switch Model GSS108E and GSS116E User Manual March 2015 202-11520-01 350 East Plumeria Drive San Jose, CA 95134 USA Support Thank you for selecting NETGEAR products.
ETHERNET IRRIGATION CONTROLLER. Irrigation Caddy Model: ICEthS1. User Manual and Installation Instructions
ETHERNET IRRIGATION CONTROLLER Irrigation Caddy Model: ICEthS1 User Manual and Installation Instructions I R R I G A T I O N C A D D Y M O D E L : I C E T H S 1 User Manual and Installation Instructions
GSMPBX version 1.3 Datasheet
GSMPBX version.3 Datasheet Document Rev.:.3 Revision Date: 23.03.203 (preliminary data) Figure - GSMPBX Introduction The GSMPBX is designed to commute phone calls between a cellular network (GSM) and the
SVA025 Netcom2 FAQ Rev 1. Mitsubishi Netcom 2 FAQ
SVA025 Netcom2 FAQ Rev 1 Mitsubishi Netcom 2 FAQ SVA025 Netcom2 FAQ Rev 1 2 What series of Netcom did we purchase? Netcom 2 FAQ Mitsubishi has several different versions of communications available. 1.
Application Notes for Configuring QuesCom 400 IP/GSM Gateway with Avaya IP Office using H.323 trunks Issue 1.0
Avaya Solution & Interoperability Test Lab Application Notes for Configuring QuesCom 400 IP/GSM Gateway with Avaya IP Office using H.323 trunks Issue 1.0 Abstract These Application Notes describe the configuration