PARTNERIllustrated Parts List CD

Transcription

1 PARTNERIllustrated Parts List CD K850 Mark II K1200 Mark II

2 A Ø /8 Ø Ø Ø , B C See Page 3 for clutch drum part # s Cylinder compl Clutch compl ,5 mm Clutch shoe (Belt) Piston Complete (K1200) Note: All parts interchange with the model K850 Mark II except: Piston Complete K850 (52 mm bore) Piston Ring K

3 D E English Standard Paper Filter Oiled Filter For assembly instructions see TechTips number Old seal STOP CHOKE F G Crankshaft compl (does not include bearings) Note: When installing, place the tapered side of the inside bearing race towards the counter weight.

4 H 12 /100 (red) / /100 (yellow) (blue) Guard Cpl Guard Cpl Guard Cpl J * Crankcase compl Vent compl Gasket Kit cpl * * * * * * * * (12, 14 ) (16 )

5 K RCJ 7Y Ignition Cpl (Black) (Greeen) Green Ignition: It may be necessary to use a standard washer between the ign. and bracket for proper alignment. Air Gap approx.: 0.4 mm / L ** ** ** ** ** ** ** ** ** ** ** ** Starter compl. ** **

6 M Carburetor compl Tillotson HS 175 D Repair kit RK 31HS Diaphragm and gasket set N

7 No. Pos. Description No. Pos. Description No. Pos. Description M Plug M Ball M Gasket, metering side M Metering diaphragm M Fuel pump diaphragm M Gasket, pump side M Screw M Spring M Lever M Needle M Filter M Spring M Needle L M Needle H M Bushing B Holder B Ring B,0 Hub E Spacer A Tube J,O Guide L Housing J Plate K Starter pawl D Mounting bracket E Throttle rod E Choke rod E Shim D Seal, old B Seal ring (large) A Spacer H Warning label A Bushing A Bushing A Bushing D Label D Label B Clutch cover A V-belt protector L Fan casing L Starter assembly A Housing H Clutch drum H Clutch drum H Clutch drum M Gasket M Screw K Spark plug connecting kit M Governor N Screwdriver J Clamp N Combi tool J Hose J Hose, 245 mm M Retaining ring M Cover M Choke flap L Starter handle E Bracket right L Decal E Stop button A,E,J,K Screw M6SF 5x20 D,E,F Screw M6SF 5x C,L,O Screw M6SF 5x J,O Screw M6SF 5x A,B,E Screw M6SF 5x J,O Screw M6SF 5x E Screw M6SF 5x D Screw M6SF 5x F Screw M6SF 5x E,K Screw M6SF 5x A Screw L Screw LKCS 3x E Screw A Nut M6MF M K Lock nut M8x E,J Nut H Washer 6.5x E Washer 5.3x K Washer 5.3x K Washer 8.4x M Washer 5.25x A Washer 15x K,O Spark plug RCJ7Y N Pin 3.6x G,J,O Ball bearing 6203C3QE A Ball bearing C,O Piston ring E Bracket left E Contact spring E Holder K Cable M Throttle flap M Cover screw D Gasket M Nipple M Ball M Idle adjustment screw M Screw M Valve K Cable J Fuel filter J Pushrod J Rod A Eccentric J Seal ring (small) K Insulating cap K Bearing housing E Throttle control E Throttle catch D Insulating flange L Plate E Absorber E Absorber E Absorber J Gasket set B Spring L Recoil spring K Spring E Spring L Lock spring G,O Needle bearing B Support bushing B Clutch shoe B Clutch L Starter rope D Intake pipe J Tank cap D Air filter D Pre-filter D Filter M Pressure spring M Sealing ring M Choke shaft M Spring M Throttle shaft D Carburetor K Flywheel E Handle, left half C Piston cpl, 52 mm K K Bracket D Rubber cover C,O Cylinder cpl C,O Piston cpl, 56 mm E Handle F Silencer N Socket wrench D Label start instructions D Decal A Bolt K Ignition cpl A Washer A Shaft A Washer A Bushing H,L Hose H Hose H Hose H Spring H Control knob H Control knob H Lever A Washer A Spacer A Spacer B V-belt A Mounting plate A Flange, support A Spacer A Washer J Hose J,O Spring L Starter pulley J Crankcase A Pulley D Air filter E Handle, front E Handle, front D Filter holder D Gasket set D Filter set D Seal J Filter J,O Gasket C,O Gasket D Gasket D Gasket C Gasket D Seal D Seal D Cylinder cover H Guard H Guard A Washer A Screw E Choke button E Handle, right G,O Crankshaft A Catch D Wing nut E Plug H Washer D Gasket J Grommet J Tank D Screw driver guide J Tank ventilation M Gasket kit H Guard A Plastic seal M Repair kit J,O Pin E Spring pin 4x K Screw MC6S 4x D Screw MC6S 5x L Screw CSK B4x L Nut M6M M K Spring washer 4.3x D Spring washer 5.3x H E-ring J Retaining ring E Lock washer G Woodruff key G,O Retaining ring J O-ring

8 PARTNER TechTips Index: 4-4 Date: Aug 99 Assembly of Rear Handle K650/K700 and K1200 When the handle is apart, follow these steps for re-assembly. 1. Insert the longer handle screw into this hole in the left handle half. This screw acts as a pivot for the trigger. 2. Install the washer, trigger and sleeve onto the screw. Fast idle button 3. Install the spring on the post identified in the drawing and insert the hook on the spring into matching hole on the trigger. 4. Install the throttle lockout. 5. Set the fast idle button by pressing on the throttle lockout and the trigger simultaneously. The fast idle button effectively holds the parts in place. 6. Install the handle assembly onto throttle linkage.