1 Dodge Cummins 5.9L Edge Comp Module Installation Instructions & Manual P/N s: 30300, READ IMPORTANT SAFETY INFORMATION IN THIS MANUAL
2 Table of Contents IMPORTANT SAFETY INFORMATION 3 SAFETY TERMS 3 SAFETY GUIDELINES 3 PRODUCT REGISTRATION 4 Benefits of product registration: 4 About the Dodge Comp 5 EGT 5 Towing Performance 6 Power Gains 6 Dodge Cummins 5.9L Comp Installation 7 Supplied Items: 7 Tools Required: 7 Power Edge Comp Getting Connected 8 Connecting In-cab to the Fuse box 8 MAP Connection 10 Injection Pump Wire Connection 11 Data Link Connection 13 Boost Elbow Installation 13 Final Inspection and Operation 14 Hot Unlock 16 Warranty Information 16 LIMITED 1 YEAR WARRANTY 16 Technical Support: , Edge Products All rights reserved. Edge Products 1080 South Depot Dr. Ogden, UT Manual Version 7 2 Edge Products Inc.
3 SAFETY TERMS IMPORTANT SAFETY INFORMATION Throughout this User Guide (hereafter referred to as User Manual or Manual) you will see important messages regarding your safety or the protection of your vehicle. These messages will be designated by the words WARNING or CAUTION. WARNING indicates a condition that may cause serious injury or death to you, your passengers or others nearby. Pay careful attention to these Warning messages, and always comply with them. They could save a life. CAUTION indicates a condition that could cause damage to your vehicle. It is important to install and operate your EDGE product in conformance with instructions in this Manual. Caution messages alert you to particularly important things to watch for to keep your vehicle operating the way you want it to. The Edge product you have bought is a high-performance product. As such, it does present some risks of which you should be fully aware. Do not use this product until you have carefully read all the following safety information and the Owner Agreement. WARNING Misapplication or misuse of this product could lead to a serious or fatal accident. Comply with all safety information below, and in your vehicle owner s manual. Follow safety, installation and operating instructions in this User Manual to assure proper use. SAFETY GUIDELINES 1. Do not exceed legal speed limits on public roadways. Use any enhanced speed capabilities of this product only in closed circuit, legally sanctioned racing environments expressly for this purpose. Loss of control from speeding on a public road could seriously injure you, your passengers, or others on the roadway. 2. Select a position on the windshield or dashboard to mount the device where it will not impair your view. You must be able to see the road, traffic, and pedestrians without interference. Be sure your mounting location meets state and local laws regarding placement of devices on the windshield or dashboard. 3. Do not operate the device while driving. Perform all adjustments or changes while stopped. Changing a setting while under way can interfere with your attention to roadway conditions. 4. Stacking performance-enhancing devices or other improper installation could cause powertrain failure on the road. Other products may have features incompatible with your Edge device. Follow all installation and operating instructions, and don t stack products. 5. Some modifications may affect other parts of your vehicle. For example, if you remove/adjust the speed limiter in your vehicle, be sure your tires and other components are rated for the increased speeds they will have to withstand. Not doing so can lead to loss of vehicle control. Modify the speed limiter only for use in closed circuit, legally sanctioned racing environments, not for use on public roadways. 6. Do not use the Performance Tests feature to break any traffic laws. Perform these tests only where they are legal and safe. 3 Edge Products Inc.
4 7. Some features may not function on all vehicle models. Check a newly-installed device for all features you intend to use. Do not rely on their working without checking first. NOTE: Dispose of this product consistent with local codes. Return to your electronics supplier for proper handling. PRODUCT REGISTRATION Please take the time to register your product. To register your product, follow the instructions at this link. Benefits of product registration: Your Safety registering your product allows us to know exactly which product you have and provide important product updates to you that improve the quality and/or safety of the product Enhanced Features almost all Edge products are easily updated via the internet. We are constantly adding new features and improvements to our product that we know you will want to enjoy Confirmation of Ownership provides a record in case of product loss, theft, or required warranty work. When you call us for support our team will already have much of the information they need to help you! Improved Product Development helps us better understand you (our customers) and design products that meet your needs Special Offers allows us to inform you about special offers on accessories and/or new products that fit your vehicle and enhance your driving experience AND Extended Warranty Plan Opportunity within the first 90 days of ownership, Edge offers the option to buy a 1-year warranty extension to all customers who register their product! All Edge modules and programmers are built to operate with OEM calibrations. When you take your vehicle to a service center they may, by your request or otherwise, update your vehicles calibrations. Therefore it is important that you return your vehicle to stock before taking it in for service. Edge updates its active products (i.e. those currently being manufactured) to work effectively with updated OEM calibrations. However, this process can take some time as Edge is not always made aware of calibration changes made by the OEM. In the case of discontinued products, Edge cannot ensure that your unit will work effectively if you take your vehicle to a dealership and you are given, by your request or otherwise, a new calibration. If you have used another tuner/programmer on your vehicle, you will need to program back to stock and remove the device before using the Edge Products Device. Failure to return to stock may result in PCM failure or engine damage. Because the Power Edge Comp module is a high performance product, it is strongly recommended that EGT gauges and Boost gauges be installed with the use of this product. 4 Edge Products Inc.
5 Programming your vehicle may expose existing defects in your vehicle s PCM that could disable your vehicle. It is advised that you do not program your vehicle in remote locations in case of vehicle failure. About the Dodge Comp IMPORTANT: Read all Safety, Warranty, and Installation Instructions before installing this product. Read through these instructions completely so that you understand each step prior to installation. Congratulations on purchasing the Comp by Edge Products, LLC, the leader in truck performance and power gain technology. The following manual contains information and instructions on the proper use of the Comp. The Edge Comp module maximizes engine efficiency by monitoring the RPM, timing, turbo boost pressure and fueling parameters of your Cummins engine. The Comp module uses this information to determine and control both fueling and timing enhancements for the Bosch fuel injection pump. The Edge Comp features five power levels with power gains from horsepower. Each of the levels has five independent adjustable sub-levels to control low boost fueling, providing a total of 25 levels of adjustability! The responsiveness settings enable you to dial-in the optimum balance between responsiveness and low boost smoke control no matter what additional power modifications have been made to the engine. The Comp module is fully adjustable on-the-fly and mounts inside the cab. EGT EGT stands for exhaust gas temperature, and is the single most important indicator of how a diesel engine is performing. Unlike a gasoline motor, a diesel engine will continue to make power as more fuel is added. As more fuel is added, heat will be generated until the engine just gets too hot and things start to melt. This is a situation you want to avoid. Exhaust gas temperature is the ideal measurement of how hot the engine is, since temperature fluctuations in exhaust gas are almost instantaneous. It is possible to generate excessive EGT on a stock truck, particularly if you are towing. This is why we always recommend installing an EGT gauge. 5 Edge Products Inc.
6 Towing Performance WARNING Do not exceed your vehicle s max GVWR as outlined in the vehicle s owner s manual. Doing so may result in loss of vehicle control and cause bodily injury. Level 1 and 2 will modify the fuel timing and fuel injection strategies to improve the performance of your vehicle. You should see an improvement in fuel economy as well as added horsepower and torque. When towing a heavy load such as a boat or camper, we recommend you use these settings. Due to the high performance nature of level 3 through 5, towing or hauling heavy loads is not recommended. Power Gains The following power gains are representative of an actual test vehicle. These gains were measured on a Mustang Dynamometer at an altitude of 4400 ft above sea level, and represent power delivered to the rear wheels of the test truck. The only modification made to the test truck was the addition of the Edge Comp module. Power gains may vary between trucks and atmospheric density and different geographic settings. An optional Hot Unlock is available (See Hot Unlock) POWER LEVEL TOTAL HP GAIN TOTAL TQ GAIN Level Level Level Level Level CAUTION: On a stock truck, it is possible to overstress the engine and transmission while driving in levels three, four, and five. WARNING Do not combine, or stack chips (modules) to gain more horsepower. The chips could be incompatible and result in powertrain failure or create dangerous conditions leading to a serious or fatal accident. 6 Edge Products Inc.
7 Dodge Cummins 5.9L Comp Installation Data Link adpt for 2000 Data Link connection Comp Module and harness Connection in cab Fuel Injection pump connection MAP Sensor Connection Ground ring terminal Connection Red to Fuse Box connection in cab. (Note: Harness shown is for years is slightly different) Supplied Items: 1. Power Edge Comp Module 2. Main Wiring Harness To Engine Compartment- Black to Ground; Gray to Fuel Injection Pump; Map Sensor Connection; Data Link Connection. Inside Cab - Red to Fuse Box 12V Power 3. Hardware kit including: Wire tap-in Connector, Wire Ties, Velcro Strips, Hose Clamp, 90 Brass Fitting, and Male Spade Fuse Connector Tools Required: Knife 2-3 ft. of wire (to help fish harness) Pliers (needle nose) Phillips Screwdriver Flat tip Screwdriver 3/8 Drive Torque Wrench 1/2 Wrench 3/8 Drive Ratchet & Sockets 1/4 Socket 5/16 Socket 7/16 Deep Well Socket 10 mm Socket 13 mm Socket 7 Edge Products Inc.
8 Power Edge Comp Getting Connected Connecting In-cab to the Fuse box WARNING An electrical charge or battery acid can burn you. Battery gas can explode or ignite. Take care when working around the battery. Follow instructions in the vehicle owner s manual for disconnecting and reconnecting a battery. 1. Determine a good 12 volt circuit for use as a power source. Verify this circuit has power while starting and running and no power with the ignition off. NOTE: A good circuit is the number 17 fuse (10 AMP Cluster A) inside the fuse panel located on the left side of the instrument panel. Remove the fuse panel cover, and locate the number 17 fuse. Attach the supplied male fuse tap connector onto the fuse. Reinstall the stock fuse with connector back into the fuse panel (this is a very tight fit). Fuse tap installed on fuse 2. Using the ½ wrench, loosen both negative battery cable clamp fasteners, remove cables from the battery posts and set each to the side. Caution: DO NOT reconnect until installation is complete. Connecting power may cause fault code in the ECM, which only an authorized dealer can remove. 8 Edge Products Inc.
9 3. Using the Phillips screwdriver, remove the three screws from the bottom of the knee bolster. Pull the bottom back towards you until it pops loose, remove it and set aside. This gives better firewall access. 4. Routing the Supplied Main Wiring Harness. Cut a ¾ slit in the grommet. Automatics- easy access is the clutch hole grommet located to the left of the firewall brake hole. Manuals or Automatics- Use the large vehicle wiring harness grommet in the firewall. Fish the supplied harness through the slit from the engine compartment into the cab under the dash. Leave about 18 of the supplied wiring harness inside of the cab (white 6-wire connector end plus the red wire.) Pass the harness cables through a Grommet in the Firewall. Figure 4 5. Route the supplied red wire up into the fuse panel. Connect the female spade to the male fuse tap connector installed in a previous step. Reinstall the fuse panel cover. 6. Reinstall the knee bolster. Align clips on bolster to holes in lower panel and push. Insert and tighten the three screws in the bottom of the bolster. MAP Sensor 7. Mount the Power Edge Comp within your reach and to suit your preference. A good location is on the knee bolster either side of the steering column. Use the two supplied Velcro strips to attach. 9 Edge Products Inc.
10 MAP Connection 8. Connect the supplied MAP sensor wiring harness to the supplied main wiring harness in the engine compartment. Disconnect the stock wiring harness at the boost sensor located to the rear of the fuel filter housing near the top of and on the engine block. Plug the supplied MAP sensor connector into the stock engine boost sensor and the stock engine wiring harness connector into the supplied MAP sensor connector. The MAP sensor shown in the image is for a 2001, the are a different sensor but in the same location. Adapter #1 Adapter #2 For 2002, locate adapter #2 between sensor and Edge harness. Map Sensor Connection (2001 Shown) For 2002, locate adapter #1 between Edge and truck harness. Front of vehicle 10 Edge Products Inc.
11 Injection Pump Wire Connection 9. Using the 13 mm socket, remove the three bolts securing the throttle bracket assembly on top of the Fuel Injection pump. Move it towards the driver s side battery. 10. Using the 10 mm socket, remove the four bolts securing the air intake and the bolt securing the oil dipstick tube. Using the 7/16 socket, loosen the clamp and rotate the air intake assembly counterclockwise to expose the Fuel Injection Pump stock wiring harness. 11. The stock wiring harness is located by following it from the center of the six fuel supply tubes up to the top rear of the pump. Slide the protective covering downward to expose these upper two wires. 12. Install the wire tap-in connector lower half with metal trough onto the wire closest to the engine block; (this is the top inner wire). Hold the wire in this trough while folding over the upper half of the tap-in connector onto the lower half. Use pliers to squeeze the two halves fully together. Pump Wire This is the top inner wire. 11 Edge Products Inc.
12 NOTE: Important-while the connector halves are being seated together the wire is not to be rotated. The stock wiring harness that plugs into the injection pump may be disconnected for better access to the wire. 13. Connect the gray wire with the male spade connector on the supplied harness, fully into the side of the wire tap-in connector as shown. Replace the protective covering over the wires. 14. Reinstall the air intake assembly onto the intake manifold using the four bolts. Install the ground wire with the ring connector on the supplied harness onto one of these bolts preferably the bolt with the large ground wire already attached to it. Using the torque wrench and 10mm socket, torque these bolts to 18 lb./ft. Install and tighten the oil dipstick tube retaining bolt. 15. Reinstall the throttle bracket onto the fuel injection pump using the three bolts. Using the torque wrench and 13mm socket, torque these bolts to 18 lb./ft. 12 Edge Products Inc.
13 Data Link Connection 14. The Data Link connector is located in different locations based on the year of the truck: the triangle shaped connector is located on the drivers side of the engine in the wiring harness near the power steering pump the three prong flat connector is located on top of the fuel lift pump that is located on the driver s side of the engine directly below the MAP sensor, note: on some 2001 truck s the connector is located on the drivers side of the engine in the wiring harness near the power steering pump. MAP Sensor & Data Link Data Link 15. A plug is installed in the data link connector on the truck to resist corrosion, remove this and install the supplied connector. NOTE: For 2000, you will need to use the supplied Adapter. Plug the adapter in between the Edge data link connector and the vehicle connector. Boost Elbow Installation 16. Using the 5/16 socket, loosen the two clamps securing the air induction hose to the air filter housing and the turbo inlet. Remove the hose and set it aside. 17. Using the pliers, remove the crimp style clamp from the hose on the brass fitting located on the now exposed lower front side of the turbocharger. Remove the hose from the brass fitting and dispose of the crimp style clamp. 18. Using the 7/16 wrench, unscrew the stock brass fitting out of the turbocharger housing. Using the 7/16 wrench, install the supplied brass fitting, tighten-be careful not to over-tighten. Slip the supplied hose clamp onto the stock hose, install the stock hose onto the supplied brass fitting and tighten the hose clamp with the ¼ socket. 13 Edge Products Inc.
14 19. Reinstall the stock air hose onto the air filter housing and turbocharger inlet. Using the 5/16 socket, tighten both clamps securely. Note: On model year with auto transmission, the wastegate is a solid line and does not have a brass elbow to be replaced. Final Inspection and Operation 20. Recheck all connections, fittings and fasteners for a properly secure installation. 21. Using the supplied wire ties, secure the wiring harness to wire wall or other engine tie point to protect from possible damage. 22. Reconnect both negative battery cables onto the battery posts. Using the ½ wrench, tighten fasteners securing the cable clamps to the battery posts. 23. Turn the ignition key on. NOTE: DO NOT START THE ENGINE! The LED on the Power Edge Comp should light when powered up. 24. With the ignition key on, check for the LED on the module. If the LED is not on, push the gray round button to turn the module on. If the LED is still not on, check for proper connections ground and 12 volt power. Do not proceed if the LED does not work as desirable. If the check engine light appears, proper connections have not been made to the MAP sensor. 25. If module does not function as described in Step 23 turn ignition key to the off position and disconnect both battery ground cables. Check all connections pull apart and inspect for bent or broken male terminals. Inspect all stock and supplied connectors thoroughly. If all connectors are good, reconnect insuring each seats tightly. Reconnect battery cables to the battery posts. Repeat steps 22 and 23. If the problem still exists please call Edge Technical support team for technical assistance. 26. To adjust power levels 1-5 on the Power Edge Module, push the corresponding arrow buttons. The left arrow will decrease level and right arrow will increase power level. The levels can be adjusted while the engine is running. 14 Edge Products Inc.
15 Attach the module to the dash with Velcro on this side. Power access button Decrease Power level. Increase Power level LED indicator lights 27. Each power level on the Power Edge Comp has a submenu that allows the user to tune in the low boost fueling to eliminate excess smoke. To access the submenu: a. Be in the power level that you what to adjust the low boost fueling for b. Press and hold the round gray button (power button) for about 2 seconds, release button c. The LED s will be flashing when in the submenu d. Use the left and right arrows to adjust the levels 1-5 e. When 1 LED is lit this results in the least responsive setting or lowest smoke, all 5 LED s lit is the most responsive f. Each power level can store a unique submenu setting g. When accessing the submenu for the first time the LED s may appear erratically lit, use the right arrow key to light all LED s then set to desired level. 28. If the Power Edge Comp does not function as described above, please call Edge Technical support team for technical assistance. 15 Edge Products Inc.
16 Hot Unlock Edge Products allows you to upgrade your Comp to include a HOT power level. The Hot level fueling curve increases power in level 5 only. Although there is not a significant increase in peak HP when compared to level 5, the level Hot fueling curve is more aggressive in the bottom and mid range and continues to add more fuel in the high RPM range. Note: At 3150 RPM in Hot Unlock, your total gains over previous level 5 power level would be 60 HP and 100 ft-lbs torque. Note: To unlock the Hot level, you will need to visit and download the Hot Unlock Form waiver. You can find this form in the sub-menu Hot Unlock Form, located on the home page of the website, or the form can be found by following the link: -pdf-32.pdf Once you complete the form, you will need to call Technical Support and get an RMA number. You will then ship your Comp with the signed form and your remittance to Edge Products to be modified. The Hot Unlock option costs $ Edge Products 1080 S. Depot Dr. Ogden, Utah Warranty Information LIMITED 1 YEAR WARRANTY Edge Products, LLC, (hereafter "SELLER") gives Limited Warranty as to description, quality, merchantability, fitness for any product s purpose, productiveness, or any other matter of SELLER's product sold herewith. The SELLER shall be in no way responsible for the product s open use and service and the BUYER hereby waives all rights other than those expressly written herein. This Warranty shall not be extended or varied except by a written instrument signed by SELLER and BUYER. The Warranty is Limited to one (1) year from the date of sale and limited solely to the parts contained within the product's kit. All products that are in question of Warranty must be returned shipping prepaid to the SELLER and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by Edge Products Inc. Under no circumstances shall the SELLER be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or reinstallation of this product, or any other contingent expenses. 16 Edge Products Inc.
17 If the BUYER sends back a failed unit that is out of warranty and chooses to buy a refurbished unit, the refurbished unit will only carry a 90 day warranty. If the BUYER purchases a new unit at a predetermined discounted rate, it will have the standard 1 year warranty. Under no circumstances will the SELLER be liable for any damage or expenses insured by reason of the use or sale of any such equipment. THE INSTALLATION OF THIS PRODUCT INDICATES THAT THE BUYER HAS READ AND UNDERSTANDS THIS AGREEMENT AND ACCEPTS ITS TERMS AND CONDITIONS. IN THE EVENT THAT THE BUYER DOES NOT AGREE WITH THIS AGREEMENT, THE BUYER MAY PROMPTLY RETURN THIS PRODUCT, IN A NEW AND UNUSED CONDITION, WITH A DATED PROOF OF PURCHASE, TO THE PLACE OF PURCHASE WITHIN THIRTY (30) DAYS FROM DATE OF PURCHASE FOR A FULL REFUND. IMPORTANT INFORMATION ABOUT YOUR VEHICLE S WARRANTY Many of our customers ask, Will your product void my vehicle s manufacturer s warranty? While the answer is straightforward from a legal standpoint, it s important to educate our customers (and all aftermarket consumers) on some industry realities and offer some common sense precautions to minimize your risk. Edge is committed to providing quality products that are safe to use. Our products do not cause damage to a vehicle when used as intended. Please keep in mind that towing in anything higher than the towing level and hard driving in race or extreme performance levels is not recommended. Consumers of aftermarket products are protected by the Federal Magnusson-Moss Warranty Act. The Act states that if something breaks on your vehicle and you take it in for warranty repair, the dealer must honor your warranty unless whatever modifications you have added to your vehicle actually caused the problem in question. However, the reality is that many dealerships have been known to void warranties on vehicles that use aftermarket products as a matter of policy. This applies in particular to those aftermarket products that produce horsepower, such as performance enhancement chips, modified intake manifolds, or aftermarket exhaust systems, regardless of product brand. You have strong legal protection as a consumer in regard to your vehicle s warranty. However, Edge strongly recommends you always disconnect and remove your module/programmer and monitor when you take your vehicle to a dealer for warranty work. In addition, leaving the product connected may affect dealer diagnostic analysis and CAN tool functions. Edge makes every effort to produce product that can be easily removed. NOTE: Even if you disconnect your unit, your dealer can detect the use of any programmer even if the unit has been removed. Thank you for purchasing the Edge Comp Module by Edge Products, LLC for the Dodge Cummins Diesel. The Comp Module has been developed and produced from the highest quality materials available to ensure the best performance for years to come. If you have any concerns or questions, please contact us. Note: This warranty is void for any new products purchased through auction websites. Warranty is valid only for new products purchased through Authorized Dealers (proof of purchase required for all warranty claims). Technical Support: To expedite your support call, please have your Vehicle Information, Part Number, Serial Number, and Date of Manufacture ready prior to calling Technical Support. The Edge Products information is found on the label located on the bottom of the device. 17 Edge Products Inc.
1998.5-2002 Dodge Cummins 5.9L 24 Valve EZ Module Installation Instructions & Manual P/N s: 30200 / 30201 READ IMPORTANT SAFETY INFORMATION IN THIS MANUAL California Air Resources Board Executive Order
03-07 Ford 6.0 Powerstroke Installation Instructions and Manual P/N: 10401 2007 Edge Products Incorporated All rights reserved. Edge Products 1080 South Depot Dr. Ogden, UT 84404 1-888-360-3343 www.edgeproducts.com
SALEEN SPEEDLAB SERIES VI STANDARD SC UPGRADE KIT INSTALLATION MANUAL: 2005 MUSTANG 4.6 3V MANUAL P/N: 10-8002-C14338C SUPERCHARGER KIT P/N: 10-1607-B14083* Saleen Performance, Inc. 1225 East Maple Rd.,
24.2L M.A.N. V12 Engine Module MANV1224 INSTALLATION INSTRUCTIONS For 24.2L M.A.N. V12 Engines V12 M.A.N. Engine Instructions Module ECM s (male and female, connect to the same ECM) ECM s (male and female,
owners manual with installation instructions dynafact boost GAUGE this manual is for use with systems 64050-64054 GENERAL INSTALLATION PRACTICES This manual is an installation guide for all 1. Banks DynaFact
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
INSTALLATION INSTRUCTIONS Electric Vacuum Pump Kit 28146 Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and carefully follow these instructions
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII23628 2003 PILOT Issue Date MAY 2002 PARTS LIST Security System Kit (sold separately): P/N 08E51-S84-100 2 Remote controls Attachment
520 Installation Instructions Thank you very much for purchasing PIAA product. Please read this entire manual before installation and use of this product. For Installers Please give this Installation Manual
Retrofit Instructions Installing a Sport Heated Steering Wheel - Leather, Multifunction BMW X5, E53, 2001 2006 Disclaimer: This set of instructions is simply a guide on how I installed my own heated steering
CI100018 INSTALLATION INSTRUCTIONS FOR 2006-2009 VW MK5 Rabbit, Jetta 2.5L These instructions are applicable to vehicles equipped with either manual or automatic transmissions Thank you for choosing to
- Easy -wire installation with no external spark box necessary, but can be used with one. - Precision CNC machining and hand assembled construction. This is a premium product. - Accurate super hot spark
Engine BHW Cooling system components, removing and installing Page 1 / 24 19-1 Cooling system components, removing and installing Warning! When doing any repair work, especially in the engine compartment,
INSTALLATION MANUAL FOR 24 VALVE 5.9L CUMMINS POWERED DODGE TRUCKS 2003 THROUGH 2004.5 MODEL RP-150 READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 5400 BUSINESS 50 WEST SUITE 8 573 635-0555
AEROMOTIVE Part # 16302 INSTALLATION INSTRUCTIONS CAUTION: Installation of this product requires detailed knowledge of automotive systems and repair procedures. We recommend that this installation be carried
TITAN pt. no.: 03 0000 0120 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
A&A CORVETTE PERFORMANCE C6 BOOST & FUEL GAUGE INSTALLATION INSTRUCTIONS 1. Check your gauges before you take them out of the packaging to make sure they are at 0 (zero) psi for both boost and fuel pressure.
GPS AutoSteer System Installation Manual Supported Vehicles John Deere Sprayers 4720 4630 4730 4830 AutoTrac Ready PN: 602-0227-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions in this manual
ADDING AN ELECTRIC AUXILIARY FAN TO RADIATOR STACK ON 03 ALPINE COACH The original design of the 03 Alpine Coaches (and perhaps other years as well) did not include any kind of engine fan engage mechanism
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: Illuminated Kick Plate APPLICATION: Rogue (2011) PART NUMBER: 999G6 GX010 KIT CONTENTS: Item A B C G H QTY 1 1 1 D 1 E 1 F 3 15 6 Description Kick Plate,
BUILT-IN DISHWASHER INSTALLATION INSTRUCTIONS PLEASE READ COMPLETE INSTRUCTIONS BEFORE YOU BEGIN LEAVE INSTALLATION INSTRUCTIONS AND USER'S GUIDE WITH OWNER ALL ELECTRIC WIRING AND PLUMBING MUST BE DONE
08 Ford F-Series 6.4L Power Stroke Edge Juice Module Installation Instructions P/N: 10103 TABLE OF CONTENTS DISCLAIMER OF LIABILITY 4 LIMITATION OF WARRANTY 4 The Edge Juice Module 7 About the Attitude
INSTALLATION MANUAL FOR 24 VALVE 5.9L CUMMINS POWERED DODGE TRUCKS 2003 THROUGH 2004.5 MODEL RP-100 READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 5400 BUSINESS 50 WEST SUITE 8 573 635-0555
92154000 Thank you for choosing Rough Country for your suspension needs. 2011-14 F250 6 RADIUS ARM KIT Rough Country recommends a certified technician installs this system. In addition to these instructions,
INSTRUCTIONS FOR THE INSTALLATION AND OPERATION OF ACTIVATOR II ELECTRONIC TRAILER BRAKE CONTROL 5500 FOR 2, 4, 6 & 8 BRAKE SYSTEMS IMPORTANT: READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY. KEEP THESE INSTRUCTIONS
Walbro 255lph Inline Fuel Pump Install Procedure Note: Instructions are based on a single in tank pump with under car OEM VW filter. Total install time for a qualified technician is approximately 2 hrs.
Voltage Regulators QD3/T350 Motor Replacement Kit Kit Number 57A63675100B Service Information S225-50-35 Contents General..................................... 1 Parts Supplied...............................
-J0 REV. 00-0-0 FRONT TURN SIGNAL RELOCATION KIT GENERAL Kit Number -0 Models This kit fits 00 and later Dyna model motorcycles (except FXDSE), relocating the front turn signal from the handlebars to the
ZAPPY 3 OWNER S MANUAL Read this manual completely before riding your Electric ZAPPY 3. TECHNICAL INFORMATION Model No. : ZAPPY 3 Product size Type of motor Motor power Battery type Battery Charger Charging
P150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs P150SC15-A2-20150813 M6 Bolt M6
TM 4.-inch Back-Up Camera Model No.: PKC0BU4 Owner s Manual and Warranty Information Read these instructions completely before using this product. Retain this Owner s Manual for future reference. INTRODUCTION
SAFETY WARNING: recommends this system be installed by a professional technician. In addition to these instructions, professional knowledge of disassembly/ reassembly procedures and post installation checks
Page 1 of 10 IMPORTANT: Before starting installation, please be sure that all items which were supplied with the kit are accounted for. Note: These instructions are to be used in conjunction with the instructions
740B Clifty Drive Madison, Indiana 47250 812-574-7777 INSTALLATION INSTRUCTIONS Portal Gear Hubs Polaris RZR XP 900 Crew A Item Description Qty A Rotor 4 B Gear Box, L 2 C Gear Box, R 2 D Gasket 4 E Cap
47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing
INSTALLATION INSTRUCTIONS MULTI-MOUNT KIT Part Number: 75330 Application: Warn HP PowerPlant P/N 71800 Your safety, and the safety of others, is very important. To help you make informed decisions about
COOPER S PULLEY UPGRADE KIT INSTALLATION INSTRUCTIONS PART NUMBER NME5011 Below are instructions for the Mini Mania Pulley Upgrade Kit, Part Number NME5011. Please take all necessary precautions for working
Page1 James Barone Racing Aftermarket Parts and Accessories 2014+ Mazda 3/6 Shift Knob Installation Instructions What you will need: Your hands 15mm deep socket Socket wrench Ok let s get started. 1. Remove
Installation Guide 2010 BMW S1000RR Full Exhaust System!! THIS PRODUCT IS DESIGNED FOR USE IN CLOSED COURSE RACING AND IS NOT INTENDED FOR HIGHWAY USE!! Congratulations on the purchase of your new TaylorMade
R02GA July 31, 2002 Dear Blue Bird Owner: This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act. Blue Bird Body Company has determined that
English Fitting Instruction: Daytona 675 Street Triple from VIN 98, Street Triple R from VIN 98 A990 Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's
Installation manual 1.75 front leveling kit 2011 Dodge Durango 2011-2014 Jeep Grand Cherokee Part # 42006 sj02282011rev.01 Part # 42006 2011-2014 Dodge Durango 2011 Jeep Grand Cherokee 1.75 front leveling
HP 16/18-Port Cable Management Kit Installation Guide Abstract This document describes how to attach the HP 16 Port or 18 Port Cable Management Kit to an HP rack. The cable management bracket is designed
NATURAL GAS TO PROPANE CONVERSION KIT 090 INSTALLATION INSTRUCTIONS FOR ALTITUDES 0 -,00 FT. ONLY PROPANE CONVERSION KIT SAFETY... INSTALLATION REQUIREMENTS... Tools and Parts... LP Gas Requirements...
15GAL STEEL OIL DRAIN WITH 110V PUMP OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety
specializing in AIR CONDITIONING, PARTS AND SYSTEMS for your classic vehicle PERFECT FIT IN-DASH HEAT/ COOL/ DEFROST 1967-72 CHEVROLET PICKUP CONTROL & OPERATING INSTRUCTIONS The controls on your new Perfect
Replacing the main board WARNING Before proceeding, turn off the main power switch and unplug the power cord. Caution Make sure you are properly grounded with an ESD strap before continuing. The main printed
-J00876 REV. 009-0-09 SECURITY SYSTEM SMART SIREN KIT GENERAL Kit Number 688-0 Models For model fitment information, see the P&A Retail Catalog or the Parts and Accessories section of www.harley-davidson.com
TOYOTA TACOMA 2008- HANDS FREE BLU LOGIC Preparation Part #: PT923-00112 Conflicts: JBL Audio, Factory Navigation NOTE: Part number of this accessory may not be the same as the part number shown. Kit Contents:
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD All 30209 2-AND 4-DOOR SYSTEM (VP, LX, SE) Issue Date AUG 2005 PARTS LIST Security System Attachment: P/N 08E55-SDA-100A Unit panel
INSTALLATION MANUAL Power-Pole Signature Series Shallow Water Anchor Installation Instructions CAUTION: Read this instruction manual carefully. Become familiar with the controls and know how to operate
Page 1 of 34 19-1 Cooling system components, removing and installing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate
4 3. SEISCO PARTS & SERVICE REMOVAL AND REPAIR GUIDE A. Changing the Control Board B. Replacing a Heating Element C. Thermistor Replacement D. High Limit Switch Replacement E. Level Detector Replacement
INSTALLATION GUIDE APPLICATION LENGTH MODEL YR PART # Bestop PART # Ford Super Duty F-250 / F-350 Regular Cab (48 ) 1999 2007 10-02513-24 75102-01 Ford Super Duty F-250 / F-350 Super Cab (60 ) 1999 2007
TITAN pt. no.: 02 0000 0143 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended
INSTALLATION INSTRUCTIONS 6111 Air Spring Kit 2011+ Ford F250/F-350 Single Wheel 2WD 2011+ Ford F350 Dually 2WD Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
Preparation Part Number(s): PT233-34070, PT923-35070-11, PT923-35070-43 NOTE: Part number of this accessory may not be the same as part number shown. Back Up Monitor Kit Contents PT923-35070-11 / PT923-35070-43
Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the
INSTALLATION INSTRUCTIONS 6108 Air Spring Kit 2011+ Ford F250 Single Wheel 4WD 2011+ Ford F350 Dually 4WD (2011 F350 Single Wheel 4WD use p/n 6113) Thank you for purchasing a quality Hellwig Product. PLEASE
Please contact the Tech Hot Line for the most current instruction information (586) 468-1356!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: These instructions
Owner s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product s
P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center
-5 Safety information The product was developed, manufactured and inspected according to the basic safety requirements of EC Guidelines and state-of-the-art technology. The instrument is designed for use
Volvo Trucks North America, Inc. Greensboro, NC USA This Service Bulletin is a supplement to Service Manual, Group, Anti-lock Brake System (ABS), Bendix, VNL, VNM publication number PV /. Service Manual
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2008 ACCORD 4-DOOR Publications No. AII 35362 Issue Date AUG 2007 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
Strut Spring Compressor Item 43753 Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL. When unpacking, make sure that the product is intact and
Thank you for purchasing a Sinister Manufacturing Company EGR delete kit. Precision manufactured using the highest grade 304 stainless steel and 6061 billet aluminum; this EGR kit is designed to endure
EVANS ELECTRONIC TEMPERATURE CONTROL TROUBLESHOOTING GUIDE for systems equipped with electric coolant valve and external PC board. This Troubleshooting Guide covers the electric coolant valve and control
21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners