How to Set Up Your CBA750B 3G/4G Wireless WAN Bridge

Transcription

1 How to Set Up Your CBA750B 3G/4G Wireless WAN Bridge The CBA750B mobile broadband series adapters enable easy-to-install wireless WAN connectivity in fixed business locations. Package Contents The CBA750B 3G/4G wireless WAN bridge appliance provides wireless connectivity as either a backup or primary connection for branch SRX Series Services Gateways. Front Panel 4G LTE WIMAX Reserved (future use) LAN WAN data activity Signal strength over Ethernet supply adapter CBA750B Mounting hardware 3G HSPA+ EVDO UMTS 2G 1XRTT Edge GPRS Failover Status (USB/ExpressCard modem) g Router/ Passthrough mode Warranty and Registration Information End-User License Agreement Safety Guide Quick Start Guide Ethernet cable g Left Side Panel Right Side Panel Computer or local device LAN switch (12V) Reset Router/Passthrough switch USB (3G/4G modem ports) g g ExpressCard slot ExpressCard lock 1

2 CBA750B 3G/4G Wireless WAN Bridge LEDs LED State 4G LTE WIMAX Reserved (future use) LAN WAN data activity Signal strength over Ethernet Solid: On 4G On: Primary connection is 4G 3G On: Primary connection is 3G 2G On: Primary connection is 2G Failover On: Secondary WAN is in use Off: Primary WAN operating normally g LAN WAN data activity On: Connected On: Data is actively being transferred Off: No data is being transferred 3G HSPA+ EVDO UMTS 2G 1XRTT Edge GPRS Failover Status (USB/ExpressCard modem) Router/ Passthrough mode Status (USB/ ExpressCard modem) Green: Connected Blinking green: Connecting Amber: Not active, might be engaged in failover process Blinking amber: Connection error Blinking red: Modem resetting PoE On: CBA750B is in PoE mode Router/Passthrough modes Green: Router mode Off: Passthrough mode NOTE: This LED matches the switch setting rather than the actual configuration (it is possible to overrule the switch settings from the administration pages). Set Up Your CBA750B 3G/4G Wireless WAN Bridge 1. Connect a Juniper Networks business-grade or USB/ExpressCard wireless broadband data modem with active subscription. b a (Optional) To integrate a business-grade modem: a. Purchase a data plan. Insert a SIM card if the model requires one. b. Connect the modem to the CBA750B. c. Insert the screws into the modem and insert antennas (finger-tight only). c 2. Plug the power supply into an electrical outlet. 3. Connect the power supply to the CBA750B and switch the device on (I). g How to Set Up Your CBA750B 3G/4G Wireless WAN Bridge 2

3 Access the Administration Pages The CBA750B can be used immediately without any configuration changes. If you want to configure any of the advanced features, log in to the administration pages. To access the administration pages: 1. Open a browser window and type cp/ or in the address bar. Press Enter. 2. When prompted for your password, type the eight-character default password found on the product label. Your unique default password is shown on the product label on the bottom of your CBA750B. g Configure the CBA750B Using the First Time Setup Wizard When you log in for the first time, you are automatically directed to the First Time Setup Wizard, which helps you customize your CBA750B. To configure the CBA750B: 1. To change any of the following options, follow the prompts in the wizard: Administrator password Time zone Access point name (APN) for SIM-based modems Modem authentication Failure Check mode After making the changes, review the details and record your administrator password. 2. Click Apply to save your settings. NOTE: To return to the First Time Setup Wizard after your initial login, select Getting Started > First Time Setup on the top navigation bar. How to Set Up Your CBA750B 3G/4G Wireless WAN Bridge 3

4 Reset the Configuration To restore the CBA750B to its factory default settings, press and hold the RESET button on the side of the device for ten seconds. Reset returns the login password to the default password and resets all configuration changes. Set Up IP Passthrough The CBA750B s IP passthrough function passes the IP address of the attached modem to the LAN. By default, the CBA750B is configured for IP passthrough the device ships with the Router/Passthrough switch set to the I position (O is router mode; I is passthrough mode). The IP passthrough function disables some of the router functionality on the device. There are three methods for setting up IP passthrough: 1. By default, the Router/Passthrough switch on the device is set to I. The I setting forces a complete IP passthrough configuration with the following settings: Update the Firmware Juniper Networks regularly creates new firmware packages. You might need to update the firmware to use the CBA750B with new modems and to access the latest features. To update the firmware: 1. Log in to the administration pages. You might have changed the Administrator Password when you used the First Time Setup Wizard. 2. Select System Settings > System Software. 3. Find the Firmware Upgrade section. This displays the current firmware version that is installed and indicates if an updated firmware is available. 4. Download the latest firmware to your desktop from the Juniper Customer Support website: 5. Click Manual Firmware Upload. Load balance is disabled; the highest priority WAN device is used. Routing Mode is set to IP Passthrough. Subnet Selection Mode is set to Automatically Create Subnet. If you have created secondary networks, they are disabled: only the primary LAN is enabled. 2. On the administration pages, select Getting Started > IP Passthrough Setup. This wizard will force an IP passthrough configuration that matches the Router/Passthrough switch settings in method For a custom configuration, manually enter the IP passthrough settings on the administration pages (this is the preferred method for network professionals). Go to Network Settings > Local Networks for most of these changes. Depending on your settings, you might also need to change the settings on the other pages. NOTE: Changes on the administration pages can overrule the switch setting, and vice versa (the most recent setting changes are implemented, regardless of the method). On the administration pages, you can set the device to ignore changes to the Router/ Passthrough switch. Select Administration > System Settings from the Local Management tab, and then click Disable IP Passthrough/Configuration mode switch. How to Set Up Your CBA750B 3G/4G Wireless WAN Bridge 4

5 Regulatory and Safety Information Read all operating instructions and the safety information below and before using the CBA750B device to avoid injury. FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/tv technician for help. FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, for the CBA750B-LE the maximum antenna gain must not exceed 8 dbi in the cellular band, 3 dbi in the PCS band and 10 dbi in the LTE band. For the CBA750B-LP the maximum antenna gain including cable loss must not exceed 7.5 dbi in the cellular band, 3 dbi in the PCS band, 5.5 dbi in LTE Band 4, and 9 dbi in LTE Band 17. For the CBA750B-W the maximum antenna gain must not exceed 9.2 dbi in the 2.5 GHz band ( MHz). SAFETY AND HAZARDS: Under no circumstances should the CBA750B device be used in any areas (a) where blasting is in progress, (b) where explosive atmospheres may be present, or (c) that are near (i) medical or life support equipment, or (ii) any equipment which may be susceptible to any form of radio interference. In such areas, the CBA750B device MUST BE POWERED OFF AT ALL TIMES (since the device otherwise could transmit signals that might interfere with such equipment). In addition, under no circumstances should the CBA750B device be used in any aircraft, regardless of whether the aircraft is on the ground or in flight. In any aircraft, the CBA750B device MUST BE POWERED OFF AT ALL TIMES (since the device otherwise could transmit signals that might interfere with various onboard systems on such aircraft). Furthermore, under no circumstances should the CBA750B device be used by the driver or operator of any vehicle. Such use of the device will detract from the driver s or operator s control of that vehicle. In some jurisdictions, use of the CBA750B device while driving or operating a vehicle constitutes a civil and/or criminal offense. Due to the nature of wireless communications, transmission and reception of data by the CBA750B device can never be guaranteed, and it is possible that data communicated or transmitted wirelessly may be delayed, corrupted (i.e., contain errors), or totally lost. The CBA750B device is not intended for, and CradlePoint recommends the device not be used in, any critical applications where failure to transmit or receive data could result in property damage or loss or personal injury of any kind (including death) to the user or to any other party. CradlePoint expressly disclaims liability for damages of any kind resulting from: (a) delays, errors, or losses of any data transmitted or received using the device; or (b) any failure of the device to transmit or receive such data. Warning: This product is only to be installed by qualified personnel! Industry Canada Statement This device complies with RSS-210, RSS-102, and RSS-Gen of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Déclaration d Industrie Canada Ce dispositif est conforme à la norme CNR-210, CNR-102, et CNR-Gen d Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. How to Set Up Your CBA750B 3G/4G Wireless WAN Bridge 5

6 Juniper Networks, Junos, Steel-Belted Radius, NetScreen, and ScreenOS are registered trademarks of Juniper Networks, Inc. in the United States and other countries. The Juniper Networks Logo, the Junos logo, and JunosE are trademarks of Juniper Networks, Inc. All other trademarks, service marks, registered trademarks, or registered service marks are the property of their respective owners. Juniper Networks assumes no responsibility for any inaccuracies in this document. Juniper Networks reserves the right to change, modify, transfer, or otherwise revise this publication without notice. Products made or sold by Juniper Networks or components thereof might be covered by one or more of the following patents that are owned by or licensed to Juniper Networks: U.S. Patent Nos. 5,473,599, 5,905,725, 5,909,440, 6,192,051, 6,333,650, 6,359,479, 6,406,312, 6,429,706, 6,459,579, 6,493,347, 6,538,518, 6,538,899,6,552,918, 6,567,902, 6,578,186, and 6,590,785. Copyright 2015, Juniper Networks, Inc. All rights reserved. Part Number: Rev. 01, July 2015.