This next section covers certain luminaires including metal halide fixtures, under cabinet units, portable luminaires, and torchieres

Transcription

1 This next section covers certain luminaires including metal halide fixtures, under cabinet units, portable luminaires, and torchieres 65

2 This section includes luminaires, which are torchieres, metal halide luminaires, portable luminaires, under cabinet luminaires, and includes luminaires with GU 24 socket and base configurations and GU 24 adaptors. 66

3 With regards to test methods for this category: (1) There is no test method for torchieres. (2) The test method for metal halide luminaires is ANSI C Ballasts may be tested separately, outside the luminaire. (3) The test method for under cabinet luminaires is 10 CFR (q) (2008). (4) The test methods for LED luminaires using LED lamps and light engines are at the manufacturers option, using either: (1) The California Joint Appendix JA8 2008, Testing of Light Emitting Diode Light Sources, or (2) The IES LM 79 08, Approved Method: Electrical and Photometric Measurements of Solid State Lighting Products, 67

4 Let s now look at the Title 20 requirements for federally regulated products. (1) Torchieres manufactured on or after January 1, 2006 shall consume not more than 190 watts of power and shall not be capable of operating with lamps that total more than 190 watts. (2) Metal halide lamp fixtures designed to be operated with lamps rated greater than or equal to 150 watts but less than or equal to 500 watts, manufactured on or after January 1, 2009, shall contain: (A) A pulse start metal halide ballast with a minimum ballast efficiency of 88 percent; or (B) A magnetic probe start ballast with a minimum ballast efficiency of 94 percent; or (C) A nonpulse start electronic ballast with: 1. a minimum ballast efficiency of 92 percent for wattages greater than 250 watts; and 2. a minimum ballast efficiency of 90 percent for wattages less than or equal to 250 watts. (D) This subsection does not apply to any metal halide lamp fixture: 68

5 1. with regulated lag ballasts; 2. that uses electronic ballasts that operate at 480 volts; or 3. that (i) are rated only for 150 watt lamps; (ii) are rated for use in wet locations, as specified by the National Electrical Code 2002, Section 410.4(A): and (iii) contain a ballast that is rated to operate at ambient air temperatures above 50º C., as specified by UL (3) See Section (n) for energy efficiency standards and energy design standards for luminaires, including standards for metal halide luminaires sold or offered for sale in California that are manufactured: (A) prior to January 1, 2009, or (B) on or after January 1,

6 This slide directs us to which set of specs to use based on when the luminaire is manufactured 69

7 And here we see the specifics of Table N 1 for pre

8 This table covers after 1/1/2010. You can see it establishes requirements for both ballast efficiency and control capabilities and includes: Indoor luminaires after 1/1/10, Outdoor luminaires after 1/1/10, and Indoor luminaires after 1/1/15 This table uses the same list of exceptions as listed for pre

9 Under cabinet luminaires that are equipped with T 8 fluorescent lamps and that are designed to be attached to office furniture and that are manufactured on or after January 1, 2006 shall be equipped with ballasts that have a ballast efficacy factor not less than the applicable values shown in Table N 2. Under cabinet luminaires that are equipped with GU 24 sockets manufactured on or after January 1, 2010 shall not be rated for use with incandescent lamps of any type, including line voltage or low voltage. EXCEPTIONS: 1. This section does not apply to luminaires equipped with T 8 ballasts designed for dimming. 2. Nor does it apply to luminaires that are: specifically and exclusively designed for use in applications where electromagnetic interference from electronic ballasts would interfere with critical, sensitive instrumentation and equipment such as medical imaging devices; and clearly, legibly, and permanently labeled, in at least 12 point type and in a place likely to be seen by the purchaser and the installer, "This luminaire or fixture is intended exclusively for use in applications where critical, sensitive equipment 72

10 would be adversely affected by electronic lamp ballast electromagnetic radiation. 72

11 And here we have the table for under cabinet luminaires manufactured after 1/1/06 73

12 Portable luminaires manufactured on or after January 1, 2010 shall meet one or more of the following requirements: 1. Be equipped with a dedicated fluorescent lamp socket connected to a high frequency electronic ballast contained within the portable luminaire; 2. Be equipped with one or more GU 24 line voltage sockets and not rated for use with incandescent lamps of any type, including line voltage or low voltage; 3. Be an LED luminaire or a portable luminaire with an LED light engine with integral heat sink, and comply with the minimum requirements shown in Table N 3; 4. Be equipped with an E12, E17, or E26 screw based socket and be prepackaged and sold together with one screw based compact fluorescent lamp or screw based LED lamp for each screw based socket on the portable luminaire. See standard for full details.; 5. Be equipped with one or more single ended, non screw based halogen lamp sockets (line or low voltage), a dimmer control or high low control, and be rated for a maximum of 100W. See the standard for certain wall mounted and art work exceptions to these requirements 74

13 And here we have Table N 3 mentioned in options 3 and 4 above. 75

14 GU 24 adaptors manufactured on or after January 1, 2010 shall not adapt a GU 24 socket to any other line voltage socket. 76

15 This and the next two slides lists the data submittals requirements for the current categories of products. Here we have torchieres and under cabinet luminaires. 77

16 This slide covers portable luminaires. 78

17 And here we have the requirements for metal halide luminaires. 79