TIMING BELT REMOVAL/INSTALLATION [KL]

Size: px
Start display at page:

Download "TIMING BELT REMOVAL/INSTALLATION [KL]"

Transcription

1 TIMING BELT REMOVAL/INSTALLATION [KL] 1. Disconnect the negative battery cable. 2. Remove the crankshaft position sensor. 3. Remove the P/S oil pump with the pipe still connected. 4. Remove the spark plugs. 5. Remove in the order indicated in the table. 6. Install in the reverse order of removal. 7. Verify the air gap. 8. Start the engine and

2 1. Inspect the pulleys and drive belt for runout and contact. 2. Verify the ignition timing. Crankshaft Pulley Removal Note Hold the crankshaft using the SSTs. Caution: The crankshaft position sensor rotor is on the rear of the crankshaft pulley, and can be damaged easily. No. 3 Engine Mount Rubber Removal Note 1. Support the engine using the chain block. 2. Remove the No. 3 engine mount rubber. No. 1 Idler Removal Note

3 1. Install the crankshaft pulley bolt. 2. Turn the crankshaft clockwise and align the timing marks. (No. 1 piston is at TDC of the compression stroke.) Caution: When removing the pulley bolt, hold the pulley so that the bolt holes are aligned, otherwise the threads can be damaged. 3. Remove the No. 1 idler pulley. Timing Belt Removal Note Caution: When removing the bolt, hold the tensioner so that the bolt holes are aligned. Otherwise the threads can be damaged. Loosen the auto tensioner bolts and remove the lower bolt.

4 Caution: Forcefully twisting the belt, turning it inside out, bending it, or allowing oil or grease on it will damage the belt and shorten its life. Note: Mark the timing belt rotating direction on the belt for proper reinstallation. Timing Belt Auto Tensioner Installation Note 1. Measure the tensioner rod projection length. Replace the auto tensioner if necessary. Projection (Free length) Type A: mm ( inch) Type B: mm ( inch)

5 Note: There are two types of tensioners and they are interchangeable. 2. Inspect the auto tensioner for oil leakage. Replace the auto tensioner as if necessary. Caution: Applying pressure of more than 9.8 kn (1,000 kgf, 2,200 lbs) can damage the auto tensioner. 3. Slowly press in the tensioner rod using a press.

6 4. Insert a pin into the hole in the body as shown, to hold the tensioner rod. Pin diameter 1.4 mm (0.055 inch) Timing Belt Installation Note Note; This must be done to reduce the timing belt resistance when the idler pulley is installed. 1. Set the tensioner in place and hand tighten the tensioner upper bolt.

7 2. Turn the camshafts clockwise and align the timing marks. 3. Using the crankshaft pulley bolt, turn the crankshaft clockwise and align the timing marks. 4. With the No. 1 idler pulley removed, install the timing belt on the pulleys in the order shown below. a. Timing belt pulley b. No. 2 idler pulley c. Camshaft pulley (LH) d. Tensioner pulley e. Camshaft pulley (RH)

8 5. Verify that there is tension between pulleys (3) and (1), and between pulleys (1) and (5). Caution: Verify that the belt has no looseness at the tension side. Do not damage the bolt threads when installing. 6. Install the No. 1 idler while applying the pressure on the timing belt.

9 7. Push the auto tensioner in the direction of the arrow and hand tighten the lower bolt. Tighten the bolts. 8. Remove the pin from the auto tensioner to apply tension to the belt. 9. Turn the crankshaft clockwise twice, and align the timing marks.

10 10. Verify that all timing marks are correctly aligned. If not, remove the timing belt and repeat from Timing Belt Auto Tensioner Installation Note. Crankshaft Pulley Installation Note Hold the crankshaft using the SSTs.

P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc

P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc P7100 PUMP INSTALLATION INSTRUCTIONS Diesel Care & Performance Inc Installation Timing Pin Location CAUTION: Before installing the injection pump, be sure that number 1 cylinder is at the Top Dead Center

More information

2003 Audi A4. AUDI' '3.0L V6 - AVK Engine - A4 & A6

2003 Audi A4. AUDI' '3.0L V6 - AVK Engine - A4 & A6 Installation (A4) CAUTION: Before installation, ensure camshafts are aligned, crankshaft is locked in place and camshaft gear bolts are loose as described in removal procedures. When turning camshaft,

More information

Cylinder head, removing and replacing

Cylinder head, removing and replacing 15-1 Cylinder head, removing and replacing WARNING! Do not re-use any fasteners that are worn or deformed in normal use. Some fasteners are designed to be used only once, and are unreliable and may fail

More information

EM 58. 19. REMOVE NO. 2 MANIFOLD STAY (a) Remove the bolt, nut and stay.

EM 58. 19. REMOVE NO. 2 MANIFOLD STAY (a) Remove the bolt, nut and stay. 57 ROVAL 1. DISCHARGE FUEL SYST PRESSURE (See page FU-9) 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery

More information

Timing belt replacement intervals

Timing belt replacement intervals Telephone: Fax: VAT Registration No.: Name: Address: Model: Year: 1994 Registration: Tel - Private: Tel - Business: Mileage: Job number: Important note Important note The intervals and procedures given

More information

CAM-03, Camshaft Assembly Oil Seal Replacement

CAM-03, Camshaft Assembly Oil Seal Replacement CAM-03, Camshaft Assembly Oil Seal Replacement Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Flywheel Lock (P9206) Balance Shaft Pin Spanner

More information

Model No: VS4815 1. SAFETY INSTRUCTIONS VS4800 2. INTRODUCTION & APPLICATIONS VS4815 3. CONTENTS. 2.1 Introduction. 2.

Model No: VS4815 1. SAFETY INSTRUCTIONS VS4800 2. INTRODUCTION & APPLICATIONS VS4815 3. CONTENTS. 2.1 Introduction. 2. Instructions for: Petrol Engine Twin Camshaft Setting / Locking Tool Kit - (incorporating Vanos Alignment) - BMW N42 & N46 Engines Model No: VS4800 Associated kit: Camshaft/Carrier Bracket Remover & Installer

More information

2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net

2740 Whitten Rd Bldg 103 Memphis, TN 38133 Telephone 901-380-9290 Email Bwilliams@Dieselcare.net Fuel Injection Pump Replacement REMOVAL Diesel Care & Performance Inc 1. Disconnect negative battery terminal. 2. Remove throttle linkage. Fuel Injection Pump Bracket 3. Remove injection pump bracket.

More information

Oregon Fuel Injection

Oregon Fuel Injection Corporate Office: P.O. Box 21121, VE Pump Removal and Installation Cummins Lock Timed Applications Removal Clean the exterior of the injection pump and mounting surfaces. 1. Disconnect the fuel return

More information

1994 Volkswagen Corrado SLC

1994 Volkswagen Corrado SLC 1994-98 ENGINES Volkswagen 2.8L 6-Cylinder ENGINE IDENTIFICATION NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL

More information

Adjustment Data MAZDA - 626-2.0 Comprex D - RF-CX

Adjustment Data MAZDA - 626-2.0 Comprex D - RF-CX Adjustment Data MAZDA - 626-2.0 Comprex D - RF-CX Engine (general) Engine code RF Capacity 1998 (cc) Idle speed 725 ± 25 Valve clearance Valve clearance Cold Inlet 0.25 (mm) Exhaust 0.35 (mm) Compression

More information

1993 VOLKSWAGEN ENGINES 2.5L 5-Cylinder. EuroVan

1993 VOLKSWAGEN ENGINES 2.5L 5-Cylinder. EuroVan Article Text ARTICLE BEGINNING 1993 VOLKSWAGEN ENGINES 2.5L 5-Cylinder EuroVan * PLEASE READ THIS FIRST * NOTE: For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES

More information

REAR SHOCK ABSORBER WITH COIL SPRING

REAR SHOCK ABSORBER WITH COIL SPRING 278 OVERHAUL COMPONENTS: see page 272. 1. REMOVE TONNEAU COVER ASSY (SEE PAGE 7627) 2. REMOVE DECK BOARD SUBASSY (SEE PAGE 7627) 3. REMOVE BACK DOOR SCUFF PLATE (SEE PAGE 7627) 4. REMOVE DECK FLOOR BOX

More information

ENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER...

ENGINE FUEL FUEL FILTER... FUEL HEATER... INJECTOR... SUPPLY PUMP... COMMON RAIL... FUEL PRESSURE LIMITTER... FUEL FILTER............................ FUEL HEATER.......................... INJECTOR.............................. SUPPLY PUMP.......................... COMMON RAIL.......................... FUEL PRESSURE

More information

CYLINDER HEAD (4A FE)

CYLINDER HEAD (4A FE) EM81 CYLINDER HEAD (4AFE) COMPONENTS EM82 ENGINE MECHANICAL REMOVAL OF CYLINDER HEAD (See page EM81) 1. DISCONNECT CABLE FROM NEGATIVE TERMINAL OF BATTERY CAUTION: Work must be started after approx. 20

More information

Engine, disassembling and assembling

Engine, disassembling and assembling 13-1 Engine, disassembling and assembling Note: Replace the oil cooler and thoroughly clean the oil passages if you find metal shavings or larger quantities of small metal particles in the engine oil,

More information

VS4760.V2. Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines. Model No: 1. SAFETY INSTRUCTIONS

VS4760.V2. Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines. Model No: 1. SAFETY INSTRUCTIONS Instructions for: Diesel Engine Setting/Locking Tool Kit Renault dci Engines Model No: VS4760.V2 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-306) Honda Accord 2003 07 General Tech Tips: Use painter s tape rather than duct tape to secure window. It will not damage paint or leave sticky residue. A plastic

More information

Instructions for: Diesel Engine Setting/Locking Kit FORD TDCi. Model No: VS4830 1. SAFETY INSTRUCTIONS 2. INTRODUCTION & APPLICATIONS

Instructions for: Diesel Engine Setting/Locking Kit FORD TDCi. Model No: VS4830 1. SAFETY INSTRUCTIONS 2. INTRODUCTION & APPLICATIONS Instructions for: Diesel Engine Setting/Locking Kit FORD TDCi Model No: VS4830 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

More information

#62192 Moroso Degree Wheel with Intake Center Line Calculator Instructions:

#62192 Moroso Degree Wheel with Intake Center Line Calculator Instructions: #62192 Moroso Degree Wheel with Intake Center Line Calculator Instructions: Items in Kit: 1-18 Inner Degree Wheel 2-20 Outer Degree Wheel 3- (4) Nylon thumb screws 4- (4) 10-32 Allen Head screws 5- (4)

More information

2001 Nissan Pathfinder LE 2001 ENGINES 3.5L V6

2001 Nissan Pathfinder LE 2001 ENGINES 3.5L V6 2001 ENGINES 3.5L V6 ENGINE IDENTIFICATION NOTE: For repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES article in GENERAL INFORMATION. Engine can be identified by fourth character

More information

Range Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual

Range Road RR Series Semi-Automatic Firewood Processor. Crated Unit Assembly Manual Range Road RR Series Semi-Automatic Firewood Processor Crated Unit Assembly Manual 1 1) Undo 8-18mm x 19mm Nuts and bolts, 2 on each leg of top frame 2) Lift top of Metal crate off and move out of work

More information

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17)

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 17 Engine-Lubrication system (Page GR-17) 17 Engine-Lubrication system (Page GR-17) Lubrication system components, removing and installing Oil pan, removing and installing Oil pressure and oil pressure switch, checking Dynamic oil pressure warning

More information

13. REAR WHEEL/BRAKE/SUSPENSION

13. REAR WHEEL/BRAKE/SUSPENSION 13. REAR WHEEL/BRAKE/SUSPENSION 13 3.5~4.5kg-m 8.0~10.0kg-m 0.8~1.2kg-m 3.0~4.0kg-m 2.4~3.0kg-m 3.5~4.5kg-m 6.0~8.0kg-m 13-0 13. REAR WHEEL/BRAKE/SUSPENSION 13 REAR WHEEL/BRAKE/SUSPENSION SERVICE INFORMATION...

More information

SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3

SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3 PART #50190 SLP 1.85 Ratio Offset Rocker Arms with Valve Springs, LS3 PACKING LIST Before installation, use this check list to make sure all necessary parts have been included. ITEM QTY CHECK PART NUMBER

More information

WORKSHOP MANUAL 50CC ENGINE HORIZONTAL LIQUID-COOLED CYLINDER

WORKSHOP MANUAL 50CC ENGINE HORIZONTAL LIQUID-COOLED CYLINDER Sales division Technical network leadership WORKSHOP MANUAL 50CC ENGINE HORIZONTAL LIQUID-COOLED CYLINDER Sales division Technical network leadership TABLE OF CONTENTS TABLE OF CONTENTS TABLE OF CONTENTS...

More information

OSCILLATAP SIEVE SHAKER MANUAL

OSCILLATAP SIEVE SHAKER MANUAL OSCILLATAP SIEVE SHAKER MANUAL Thank you for purchasing the OSCILLATAP sieve shaker. You and your company will enjoy many years of use from this quality testing system. The Oscillatap sieve shaker has

More information

ENG-10, Camshaft (Timing) Belt and Balance Shaft Belt Tension - Checking and Adjusting

ENG-10, Camshaft (Timing) Belt and Balance Shaft Belt Tension - Checking and Adjusting ENG-10, Camshaft (Timing) Belt and Balance Shaft Belt Tension - Checking and Adjusting Tools Jack stands Floor Jack Metric Socket set Metric Wrench set Porsche Timing Belt Tension tool (P9201) Thin 24

More information

2003 ACCORD - Automatic Transmission Removal

2003 ACCORD - Automatic Transmission Removal 2003 ACCORD - Automatic Transmission Removal Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger balancer bar VSB02C000019 Front subframe adapter VSB02C000016 These special

More information

Petrol Engine Twin Camshaft & Diesel Engine Setting / Locking Tool

Petrol Engine Twin Camshaft & Diesel Engine Setting / Locking Tool Instructions for: Petrol Engine Twin Camshaft & Diesel Engine Setting / Locking Tool Kit Model No: VS4960 Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if

More information

Service Bulletin 08-045. Chirp From the Timing Belt Area (Supersedes 08-045, dated May 21, 2010, to revise the information marked by the black bars)

Service Bulletin 08-045. Chirp From the Timing Belt Area (Supersedes 08-045, dated May 21, 2010, to revise the information marked by the black bars) Service Bulletin 08-045 Applies To: See VEHICLES AFFECTED February 17, 2011 Chirp From the Timing Belt Area (Supersedes 08-045, dated May 21, 2010, to revise the information marked by the black bars) REVISION

More information

01 12 COOLING SYSTEM COOLING SYSTEM. End of Toc. End Of Sie

01 12 COOLING SYSTEM COOLING SYSTEM. End of Toc. End Of Sie LOCATION INDEX. 1 SERVICE WARNINGS...................... 2 ENGINE COOLANT LEVEL INSPECTION..................... 2 ENGINE COOLANT PROTECTION INSPECTION..................... 2 ENGINE COOLANT REPLACEMENT..

More information

INSIDE ENGINE COMPARTMENT TOYOTA AIR CONDITIONING ENGLISH EUROPE,GENERAL,AUSTRALIA

INSIDE ENGINE COMPARTMENT TOYOTA AIR CONDITIONING ENGLISH EUROPE,GENERAL,AUSTRALIA INSIDE ENGINE COMPARTMENT TOYOTA AIR CONDITIONING ENGLISH EUROPE,GENERAL,AUSTRALIA INTRODUCTION IMPORTANT NOTICE This manual has been designed for technicians who are qualified and educated in the proper

More information

Chapter 2 Part A: In-car engine repair procedures

Chapter 2 Part A: In-car engine repair procedures 2A 1 Chapter 2 Part A: In-car engine repair procedures Contents Camshaft - removal, inspection and refitting...... See Chapter 2B Compression check......................... See Chapter 2B Crankshaft rear

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 47 Brakes - Hydraulic Components (Page GR-47) 47 Brakes - Hydraulic Components (Page GR-47) FS III front brake calipers, servicing Front brake caliper piston, removing and installing FN 3 front brake calipers, servicing Front caliper piston, removing

More information

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 15 Engine- Cylinder head, Valvetrain (Page GR-15)

Volkswagen New Beetle 2.0 Liter 4-cyl General, Engine (Engine Code AEG) 15 Engine- Cylinder head, Valvetrain (Page GR-15) 15 Engine- Cylinder head, Valvetrain (Page GR-15) Cylinder head, removing and installing Compression, checking Valve train, servicing Camshaft oil seal, replacing Camshaft, removing and installing Hydraulic

More information

HYBRID CAM PLATE AND HIGH VOLUME OIL PUMP KIT

HYBRID CAM PLATE AND HIGH VOLUME OIL PUMP KIT -J056 REV. 0-05-0 HYBRID CAM PLATE AND HIGH VOLUME OIL PUMP KIT GENERAL Kit Number 584- Models For model fitment information, see the P&A retail catalog or the Parts and Accessories section of www.harley-davidson.com

More information

Fuel Injection Pump, Rotary (005-014)

Fuel Injection Pump, Rotary (005-014) Fuel Injection Pump, Rotary View Related Topic Page 1 of 30 Fuel Injection Pump, Rotary (005-014) Table of Contents Summary General Information Preparatory Steps Remove Front Gear Train Rear Gear Train

More information

Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna)

Parts#MB003-003 Reverse Gear MAMBA (Monoblock for Cable operated) For 5 speed Trans., '87 to '06 Big Twin models (except '06 Dyna) Installation Instructions Reverse Gear MAMBA (Monoblock for Cable operated) Read and become familiar with these installation instructions before start. Two Piece for H-D 5 Speed Trans., Cable operated

More information

STEERING SYSTEM - POWER

STEERING SYSTEM - POWER STEERING SYSTEM - POWER 1990 Nissan 240SX 1990 STEERING Nissan - Power Rack & Pinion Axxess, Maxima, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION The power steering system consists of a rack and

More information

300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS

300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS Section: MOYNO 500 PUMPS Page: 1 of 8 Date: March 1, 1998 SERVICE MANUAL MOYNO 500 PUMPS 300 SERIES 331, 332, 333, 344, 356 AND 367 MODELS Mechanical Seal Models Packing Gland Models MODELS DESIGN FEATURES

More information

DRIVE AND DRIVEN PULLEY

DRIVE AND DRIVEN PULLEY 11 DRIVE AND DRIVEN PULLEY SCHEMATIC DRAWING ------------------------------------------------- 11-1 SERVICE INFORMATION------------------------------------------------ 11-2 TROUBLESHOOTING-----------------------------------------------------

More information

INSTRUCTION. Industrial Sewing Machines. No. 010012. First published : June 1997 Second edition : March 2001

INSTRUCTION. Industrial Sewing Machines. No. 010012. First published : June 1997 Second edition : March 2001 INSTRUCTION Industrial Sewing Machines First published : June 1997 Second edition : March 2001 No. 010012 INTRODUCTION Thank you for your purchasing Kansai Special's DLR Series. Read and study this instruction

More information

Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008)

Unit: mm(in) Item Standard value Service limit Axle shaft run out - 0.2(0.008) Rear Wheel/Brake/Suspension 13. Rear Wheel/Brake/Suspension Service Information 13-1 Troubleshooting 13-2 Rear Wheel 13-3 Rear Cushion 13-4 Rear Swing Arm 13-7 Service Information General Safety If the

More information

Tri-Homo Style Operation and Maintenance Instructions

Tri-Homo Style Operation and Maintenance Instructions Tri-Homo Style Operation and Maintenance Instructions One Research Drive Stratford, CT 06615 (203) 375-0063 www.sonicmixing.com 1 Installation and Start-up Do not perform following adjustments without

More information

REMOVAL AND INSTALLATION

REMOVAL AND INSTALLATION 303-01C-1 REMOVAL AND INSTALLATION Engine Body On Special Tool(s) Adapter For 303-D043 303-D043-02 or equivalent Special Tool(s) 303-01C-1 Turbocharger Lifting Bracket 303-1266 Wrench, Fan Clutch Nut 303-214

More information

Rebuild Instructions for 70001 and 70010 Transmission

Rebuild Instructions for 70001 and 70010 Transmission Rebuild Instructions for 70001 and 70010 Transmission Brinn, Incorporated 1615 Tech Drive Bay City, MI 48706 Telephone 989.686.8920 Fax 989.686.6520 www.brinninc.com Notice Read all instructions before

More information

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER

STEERING HANDLEBAR/FRONT WHEEL/ FRONT SHOCK ABSORBER 14 14 STEERING HANDLEBAR/FRONT WHEEL/ SCHEMATIC DRAWING ------------------------------------------------- 14-1 SERVICE INFORMATION------------------------------------------------ 14-2 TROUBLESHOOTING-----------------------------------------------------

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46)

Volkswagen Jetta, Golf, GTI 1999, 2000 Brake System 46 Brakes - Mechanical Components (Page GR-46) 46 Brakes - Mechanical Components (Page GR-46) Front brakes Brake pads, removing and installing Brake pads, removing and installing FN 3 brake caliper, servicing FS III brake caliper, servicing Rear wheel

More information

Cylinder head gasket, replacement

Cylinder head gasket, replacement "VCC065612 EN 20110604" 1(7) Cylinder head gasket, replacement Special tools: 999 5098 Disconnect battery earth lead Drain coolant Remove heat shield over exhaust manifold. (Only the two bottom bolts on

More information

Rear wheel brakes, servicing. Стр. 1 из 45. Note:

Rear wheel brakes, servicing. Стр. 1 из 45. Note: Volkswagen Touareg - Rear wheel brakes, servicing Стр. 1 из 45 46-2 Rear wheel brakes, servicing Rear brakes, FN 44 brake caliper, servicing Note: After replacing brake pads, depress brake pedal firmly

More information

JANUS INTERNATIONAL CORPORATION INSTALLATION INSTRUCTIONS Pantheon Mini Operator

JANUS INTERNATIONAL CORPORATION INSTALLATION INSTRUCTIONS Pantheon Mini Operator JANUS INTERNATIONAL CORPORATION INSTALLATION INSTRUCTIONS Pantheon Mini Operator The Janus Pantheon mini operator does not typically require the provision of any additional site requirements other than

More information

COOLING SYSTEM Section Page

COOLING SYSTEM Section Page 5 COOLING SYSTEM Section Page 5.1 COOLANT PRE-HEATER... 5-3 5.2 COOLANT PUMP NON-EGR ENGINE... 5-7 5.3 COOLANT PUMP EGR ENGINE... 5-13 5.4 FRONT CONNECTOR HOUSING NON-EGR ENGINE... 5-17 5.5 FRONT CONNECTOR

More information

TECHNICAL MANUAL FOR THE STAND ALONE BELT DRIVE ENCODER SYSTEM

TECHNICAL MANUAL FOR THE STAND ALONE BELT DRIVE ENCODER SYSTEM INTERNATIONAL LIFT EQUIPMENT LTD London Office Leicester Office Units 1&2 Wanlip Road Highams Park Ind Estate Syston Larkshall Road Leicester London Leicestershire E4 9JD LE7 1PD Telephone 0208 5279669

More information

12-Volt Negative Ground Installation Instructions

12-Volt Negative Ground Installation Instructions 12-Volt Negative Ground Installation Instructions For Part Number: 1141, 1164, 1165, 1181 CAUTION!!! Before installing, please read the following important information... 1. The Ignitor is designed for

More information

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR

INSTALL/REMOVAL INSTRUCTIONS: WINDOW REGULATOR REMOVAL/INSTALL OF WINDOW REGULATOR (741-644) Cadillac Escalade, Chevrolet Suburban, Chevrolet Tahoe, GMC Yukon, Chevrolet Silverado, GMC Sierra 2000 05 General Tech Tips: Use painter s tape rather than

More information

MKV Golf GTI Rear Brake Service - Replace Pads and Rotors

MKV Golf GTI Rear Brake Service - Replace Pads and Rotors Page 1 Installation Procedures MKV Golf GTI Rear Brake Service - This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of

More information

ENGINE 4G1 SERIES CONTENTS GENERAL INFORMATION ... 1. SPECIFICATIONS... 11A-1-1 SERVICE SPECIFICATIONS REWORK DIMENSIONS TORQUE SPECIFICATIONS ...

ENGINE 4G1 SERIES CONTENTS GENERAL INFORMATION ... 1. SPECIFICATIONS... 11A-1-1 SERVICE SPECIFICATIONS REWORK DIMENSIONS TORQUE SPECIFICATIONS ... 11A-0-1 ENGINE 4G1 SERIES CONTENTS GENERAL INFORMATION... 11A-0-3 1. SPECIFICATIONS... 11A-1-1 SERVICE SPECIFICATIONS REWORK DIMENSIONS TORQUE SPECIFICATIONS......... NEW TIGHTENING METHOD-BY USE OF BOLTS

More information

VW 2.0T FSI. Timing Belt Installation. This tutorial is provided as a courtesy by ECS Tuning.

VW 2.0T FSI. Timing Belt Installation. This tutorial is provided as a courtesy by ECS Tuning. VW 2.0T FSI Timing Belt Installation This tutorial is provided as a courtesy by ECS Tuning. Proper service and repair procedures are vital to the safe, reliable operation of all engine vehicles as well

More information

Turbocharger system components, servicing

Turbocharger system components, servicing 21-1 Turbocharger system components, servicing Engine codes: AAZ, 1Z, AHU Observe rules of cleanliness Page 21-10 Turbocharger hoses and lines, connecting Page 21-11 WARNING! Do not re-use any fasteners

More information

BETTIS CONVERSION INSTRUCTIONS TO CONVERT HD SERIES ACTUATORS TO HD-M3, HD-SR-M3 HD-M3HW OR HD-SR-M3HW SERIES PNEUMATIC ACTUATORS

BETTIS CONVERSION INSTRUCTIONS TO CONVERT HD SERIES ACTUATORS TO HD-M3, HD-SR-M3 HD-M3HW OR HD-SR-M3HW SERIES PNEUMATIC ACTUATORS BETTIS CONVERSION INSTRUCTIONS TO CONVERT HD SERIES ACTUATORS TO HD-M3, HD-SR-M3 HD-M3HW OR HD-SR-M3HW SERIES PNEUMATIC ACTUATORS PART NUMBER: 132581 REVISION: A RELEASE DATE: 24 March 2000 Page 1 of 10

More information

Solstice/Sky Water Pump Replacement

Solstice/Sky Water Pump Replacement Solstice/Sky Water Pump Replacement The water pump on the Solstice/Sky is starting to need replacement on some vehicles. This guide will help in replacing the water pump while the engine is still in the

More information

Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing

Volkswagen B3 Passat Manual Transmission 02A 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed. Gearshift cable/lever installing 34 Manual Transmission - Controls, Assembly (Page GR-34) 02A 5-speed Gearshift cable/lever installing Gearshift housing repairing Gearshift lever repairing lever/relay lever, installing Gearshift mechanism

More information

Installation instructions, accessories - Handsfree for cellular phone, system B, entry level

Installation instructions, accessories - Handsfree for cellular phone, system B, entry level XC90 Section Group Weight(Kg/Pounds) Year Month 3 39 0.5/1.1 2006 07 XC90 2003, XC90 2004 IMG-249663 Page 1 of 18 Required tools A0000162 A0000163 IMG-239664 M0000232 IMG-253123 IMG-252223 Page 2 of 18

More information

PARTS MANUAL EH12-2 ENGINE. Model. PUB-EP5713 Rev. 7/99

PARTS MANUAL EH12-2 ENGINE. Model. PUB-EP5713 Rev. 7/99 PARTS MANUAL Model EH12-2 ENGINE PUB-EP5713 Rev. 7/99 940 Lively Blvd. Wood Dale, IL 60191 Phone: 630-350-8200 Fax: 630-350-8212 e-mail: sales@robinamerica.com www.robinamerica.com Copyright 1999 Robin

More information

Model Year: 2010 Model: Prius Doc ID: RM000001Y3B015X. Title: ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT (2010 Prius)

Model Year: 2010 Model: Prius Doc ID: RM000001Y3B015X. Title: ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT (2010 Prius) Last Modified: 5-3-2010 6.4 N From: 200904 Model Year: 2010 Model: Prius Doc ID: RM000001Y3B015X Title: ALIGNMENT / HANDLING DIAGNOSIS: FRONT WHEEL ALIGNMENT: ADJUSTMENT (2010 Prius) ADJUSTMENT If the

More information

The Crankshaft Oil Seal Section has been added to the DD15 Workshop Manual. The sections that are found in the Engine Chapter are now renumbered.

The Crankshaft Oil Seal Section has been added to the DD15 Workshop Manual. The sections that are found in the Engine Chapter are now renumbered. NUMBER: 08 DD15-5 S.M. REF.: 1.11 ENGINE: DD15 DATE: July 2008 SUBJECT: CRANKSHAFT OIL SEAL SECTION PUBLICATION: DDC-SVC-MAN-0002 The Crankshaft Oil Seal Section has been added to the DD15 Workshop Manual.

More information

The Ford Model A Water Pump

The Ford Model A Water Pump The Ford Model A Water Pump George Washington Chapter, Inc. 3903 Old Lee Highway Fairfax, VA 22030 1 Table of Contents Introduction/Specifications.. 3 1. Water Pump Inspection and Removal. 4 a. Removal..

More information

Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17)

Volkswagen Jetta, Golf, GTI 1999, 2000 2.8 Liter VR6 2V Engine Mechanical, Engine Code(s): AFP 17 Engine-Lubrication (Page GR-17) 17 Engine-Lubrication (Page GR-17) Lubrication system components, removing and installing Oil filter housing, disassembling and assembling Oil pan, removing and installing Oil pressure and oil pressure

More information

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions

LIFT-505. BMF Lift Kit. Yamaha Drive Gas or Electric. Installation Instructions LIFT-505 BMF Lift Kit Yamaha Drive Gas or Electric Installation Instructions Contents of LIFT-505 Yamaha Drive BMF Lift Kit: a (1 ea.) BMF A-Arm Assembly b (1 ea.) Driver Side Shock Tower c (1 ea.) Passenger

More information

Figure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top.

Figure 2 The fan and shroud also needs to be removed for access to the four a/c compressor bolts and removal of the compressor from the top. Here are some pictures to show what s required when replacing the A/C compressor, expansion valve and receiver/drier on a 2001 Volvo V70. Even if you don t replace these A/C parts these pictures can help

More information

Engine. 204-1890 Strobe light, 110V 204-1891 Strobe light, 220V 204-458 Replacement bulb. 204-1057 Compression gauge. 204-166 Dial indicator

Engine. 204-1890 Strobe light, 110V 204-1891 Strobe light, 220V 204-458 Replacement bulb. 204-1057 Compression gauge. 204-166 Dial indicator The Strobe light checks the unit for: Balance of operating machinery RPM of motors, engine pulleys, fans, etc. Observe belt slippage Strobe light will stop action at speeds from 200 to 6000 RPM 204-1890

More information

Sebring Timing Belt and Water Pump Replacement

Sebring Timing Belt and Water Pump Replacement Sebring Timing Belt and Water Pump Replacement I was motivated to do this work because of a bearing growling sound emanating from the engine. It would grind at low rpms when the engine was cold and then

More information

Drive shaft, servicing

Drive shaft, servicing Volkswagen Passat B6 - Drive shaft, servicing Стр. 1 из 41 40-7 Drive shaft, servicing Drive shafts, overview I - Assembly overview: Drive axle with CV joint VL100 40-7, Drive axle with CV joint VL100,

More information

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997

Char-Lynn Hydraulic Motor. Repair Information. 10 000 Series. October, 1997 Char-Lynn Hydraulic Motor October, 1997 Repair Information Geroler Motor Two Speed 001 27 Retainer inside bore of valve plate bearingless motors only 4 15 16 3 6 35 Parts Drawing 25 2 2 1 19 17 36 40 47

More information

Service. Engine. Engine Model: General Motors 4.3 L Powertrain. Generator Models: 30--45 kw TP-6103 1/01

Service. Engine. Engine Model: General Motors 4.3 L Powertrain. Generator Models: 30--45 kw TP-6103 1/01 Service Engine Engine Model: General Motors 4.3 L Powertrain Generator Models: 30--45 kw TP-6103 1/01 CAUTION Caution: In order to reduce the chance of personal injury and/or property damage, carefully

More information

http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html

http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html http://waterheatertimer.org/troubleshoot-rheem-tankless-water-heater.html TECHNICAL SERVICE DEPARTMENT Removal, Cleaning, & Reinstallation of the Burner Assembly For models 74 & GT199 Required tools -

More information

Universal Adjustable Fuel Pressure Regulator

Universal Adjustable Fuel Pressure Regulator Universal Adjustable Fuel Pressure Regulator Installation Instructions for: Part Numbers 25-302 U.S. Patent # 6,298,828! Due WARNING: to the fact that this installation deals with your fuel system this

More information

cbperformance.com Please read this entire brochure prior to installing your CB Performance Products MAGNASPARK II distributor.

cbperformance.com Please read this entire brochure prior to installing your CB Performance Products MAGNASPARK II distributor. - Easy -wire installation with no external spark box necessary, but can be used with one. - Precision CNC machining and hand assembled construction. This is a premium product. - Accurate super hot spark

More information

6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included:

6 inch A-Arm Lift Kit WARNING: 16-018/16-019. installation instructions. will fit CLUB CAR DS. included: Revised May 205 6-08/6-09 6 inch A-Arm Lift Kit will fit CLUB CAR DS installation instructions included: Rear Lift Blocks Main Suspension Assembly Spindles A-Arms Rear Shock Mounting Plates U-Bolts WARNING:

More information

STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE AUTO 220 INTERNAL COMBUSTION ENGINES

STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE AUTO 220 INTERNAL COMBUSTION ENGINES STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE AUTO 220 INTERNAL COMBUSTION ENGINES Prepared By: BRANDON BALDWIN CANINO SCHOOL OF ENGINEERING TECHNOLOGY AUTOMOTIVE TECHNOLOGY

More information

Chapter 61. Propeller

Chapter 61. Propeller Chapter 61 Propeller PAGE 1 Table of Contents Chapter Title 61-00-00 GENERAL.................................. 3 61-10-00 PROPELLER............................... 4 61-20-00 CONTROLLING.............................

More information

MEASURING WHEEL ALIGNMENT

MEASURING WHEEL ALIGNMENT MEASURING WHEEL ALIGNMENT 2003-04 WHEEL ALIGNMENT Specifications & Procedures - Hummer - H2 Steering and vibration complaints are not always the result of improper alignment. One possible cause is wheel

More information

Hot-End Replacement Guide. BFB 3000 plus & 3D Touch

Hot-End Replacement Guide. BFB 3000 plus & 3D Touch Hot-End Replacement Guide BFB 3000 plus & 3D Touch Pre assembly checks: Testing the hot-end before fitting: Check the heating cable: Set the multi-meter to read resistance (2000 ohms) Test the two outside

More information

1/29/2008 DR70. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43

1/29/2008 DR70. Baja Motorsports Inc. P.O. Box 61150 Phoenix, AZ 85082 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43 DR70 Toll Free: 888-863-2252 PART NUMBERS PRICES ARE SUBJECT TO CHANGE 1 of 43 CYLINDER & CYLINDER HEAD 1 DR70-001 883099044472 CYLINDER 1 1 2 DR70-002 883099044489 GASKET, CYLINDER 1 1 3 DR70-003 883099044496

More information

Service Manual Rol-Lift

Service Manual Rol-Lift R 2000 Service Manual Rol-Lift Series: T and E Developed by Generic Parts Service This manual is intended for basic service and maintenance of the Rol-Lift pallet jack. The pallet jacks you are servicing

More information

Drive Belt Tensioner Damper. Drive Belt Tensioner. Battery Timing Belt Gasket

Drive Belt Tensioner Damper. Drive Belt Tensioner. Battery Timing Belt Gasket EM14 ENGINE MECHANICAL (2JZGTE) TIMING BELT TIMING BELT COMPONENTS EM0AC02 M/T Drive Belt Tensioner Drive Belt Tensioner Damper Air Cleaner Duct Oil Filler Cap x 10 No.3 Timing Belt Cover Gasket Fan and

More information

Timing Belt Change 200 TDI Land Rover Supplied by: Jason Crawford www.landroverweb.com

Timing Belt Change 200 TDI Land Rover Supplied by: Jason Crawford www.landroverweb.com Timing Belt Change 200 TDI Land Rover Supplied by: Jason Crawford If there was ever a job that was made out to be more than it should be, then this is it. Changing a timing belt on a Defender is pretty

More information

Magneto Timing. The selected wire(s) from the magneto(s) distributor must be connected to this cylinder. And the crankshaft/magneto must be spinning.

Magneto Timing. The selected wire(s) from the magneto(s) distributor must be connected to this cylinder. And the crankshaft/magneto must be spinning. Magneto Timing The two areas of timing a magneto are internal, and external. A number of things must occur at the same time, or in a well orchestrated sequence for the engine to function. Magneto Timing

More information

Cooling system components, servicing

Cooling system components, servicing 19-1 Cooling system components, servicing WARNING! The cooling system is pressurized when the engine is warm. When opening the expansion tank, wear gloves and other appropriate protection, cover the cap

More information

ARTICLE BEGINNING APPLICATION IDENTIFICATION DESCRIPTION LUBRICATION & ADJUSTMENT TROUBLE SHOOTING. MANUAL TRANSMISSIONS Saab 5-Speed Transaxle

ARTICLE BEGINNING APPLICATION IDENTIFICATION DESCRIPTION LUBRICATION & ADJUSTMENT TROUBLE SHOOTING. MANUAL TRANSMISSIONS Saab 5-Speed Transaxle Article Text ARTICLE BEGINNING MANUAL TRANSMISSIONS Saab 5-Speed Transaxle APPLICATION TRANSMISSION APPLICATION ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ Vehicle Application Transmission

More information

ASSEMBLY MANUAL SE-4S35

ASSEMBLY MANUAL SE-4S35 Automatic drive ASSEBLY ANUAL SE-4S35 AI-4S35 SG-4R35 Battery box otor unit Inter-4 hub CONTENTS WARNING 1 INSTALLATION CONITIONS Battery box Speed sensor Cable lengths and diameters otor unit Recommended

More information

CETAC Z-Drive Assembly

CETAC Z-Drive Assembly CETAC Z-Drive Assembly Replacement Guide Manual Part Number 610144 Rev 1, 2012 CETAC Technologies, Printed in USA Overview This guide describes the necessary steps to replace the Z-drive assembly on your

More information

Digital Ignition ZDG3

Digital Ignition ZDG3 Digital Ignition ZDG3 Fitting instructions for digital ignition ZDG3 for Moto Guzzi available for Bosch, Ducati or Saprisa alternators 1. Function 2. Fitting 3. Electrical connection 4. Adjustments 5.

More information

INSTALLATION MANUAL INSIDE ENGINE COMPARTMENT ZZT22#R (1ZZ-FE / 3ZZ-FE) / AZT220R (1AZ-FE) FOR EUROPEAN SPEC. AIR CONDITIONING ENGLISH.

INSTALLATION MANUAL INSIDE ENGINE COMPARTMENT ZZT22#R (1ZZ-FE / 3ZZ-FE) / AZT220R (1AZ-FE) FOR EUROPEAN SPEC. AIR CONDITIONING ENGLISH. HFC 134a Ozone Friendly Refrigerant ZZT22#R (1ZZ-FE / 3ZZ-FE) / AZT220R (1AZ-FE) FOR EUROPEAN SPEC. AIR CONDITIONING ENGLISH AAAMU-63 INSIDE ENGINE COMPARTMENT INSTALLATION MANUAL 2000 (EUROPE) B.V.. All

More information

Front axle components, overview

Front axle components, overview just a test. Front axle components, overview 40-1 General Information Load bearing components and parts of the suspension must not be welded or straightened. Vehicles without drive axle must not be moved,

More information

Auto Sentry-eXP Maintenance

Auto Sentry-eXP Maintenance Auto Sentry-eXP Maintenance Maintenance Procedures for Auto Sentry exp Bill Dispenser Credit Card Reader Bill Acceptor Bill Dispenser Maintenance Bill Dispenser Problem / Cause Bill Dispenser Error Codes

More information

Easy Tool Retracting System CMC-SR2159ER36

Easy Tool Retracting System CMC-SR2159ER36 Easy Tool Retracting System CMC-SR2159ER36 Pepperl+Fuchs, Inc. 1600 Enterprise Parkway Twinsburg, Ohio 44087 Phone: +1 330 486 0002 e-mail: pa-info@us.pepperl-fuchs.com Mounting the Easy Tool Refer to

More information

1.8 CRANKSHAFT OIL SEALS

1.8 CRANKSHAFT OIL SEALS SERIES 60 SERVICE MANUAL 1.8 CRANKSHAFT OIL SEALS An oil seal is fitted between each end of the crankshaft and the bores of the flywheel housing and gear case cover to retain the lubricating oil in the

More information

SE-900-MP ECO -SERIES. Operation & Parts Manual

SE-900-MP ECO -SERIES. Operation & Parts Manual SE-900-MP ECO -SERIES Operation & Parts Manual SE 900 MP ECO - SERIES OWNERS MANUAL Table of Contents 1. Installation guide 2. Set-up instructions 3. Operation instructions 4. Cleaning 5. Troubleshooting

More information