Hardware Fitting Accessories Information

Transcription

1 Information Door seals Areas of application Protection against cold, draught and vermin Reduces light leakage Sound insulation Smoke control Fire resistance Reduces the energy consumption of air conditioning systems (see following example) Example calculation for energy saving: Door width 96 mm Pressure difference between indoor and outdoor Pa (equals a room temperature of 25 ºC and a relative humidity of 90% as well as an outdoor temperature of 35 ºC and a relative humidity of 70%) Retractable seal Sill seal The sealing profile is pressed automatically against the floor or engages with a sill as the door is closed. Door seals can be distinguished between retractable seals and sill seals. Sill seals are always used in combination with a threshold, it is, however, recommended to use retractable seals also in combination with a threshold in case of carpet fitted floors or butt joints. Retractable door seals are available with single-side or double-side release mechanism. Seals with single-side release are released on the hinge side or on the lock side, depending on the model. Double-side release always means release on the hinge and on the lock side. With double-side release seals, the sealing profile is raised and lowered without dragging along the floor, which prolongs its service life considerably. Door gap height (mm) Leakage rate approx. 41 m 3 /h with 7 mm air gap Without seal With seal Door gap height (mm) Leakage rate approx. 2 m 3 /h with 7 mm air gap AH.25

2 Weather seal, brush type Protection against cold, draught and vermin For mortise fixing or face fixing Technical Data Total height: 50 mm Brush height: 25 mm Filaments Fe: Horsehair Carrier Fe: Sheet steel galvanized Filaments Al: Polyamide black Carrier Al: Aluminium silver coloured Protection against cold, draught and vermin Screw fixing underneath Technical Data Total height: 19 mm Brush height: mm Filaments: Polyamide black Carrier: Aluminium silver coloured anodized Fe Al 1,000 mm ,250 mm ,000 mm Packing : 1 pc. 1,000 mm ,250 mm ,000 mm Packing : 1 pc. AH.26

3 Weather seal, brush type Retractable door seal Protection against cold, draught and vermin For mortise fixing Technical Data Total height: 16 mm Brush height: 12 mm Filaments: Polyamide black Carrier: Sheet steel galvanized Protection against cold, draught and vermin Reduces the energy consumption of air conditioning systems Reduces light leakage For soundproofing doors For full mortise fitting Suitable for DIN left hand and DIN right hand Single-side release Technical Data Max. sealing height: 11 mm Can be shortened at one end by max.: 0 mm Required groove width: 12 mm Carrier: Aluminium Seal profile: Silicone grey, self-extinguishing Supplied with 1 Retractable door seal 2 Fixing brackets with screws 1 Release plate with screw Single-side release 1,000 mm ,250 mm ,000 mm Packing : 1 pc. 630 mm mm mm mm ,030 mm ,130 mm Packing : 1 pc. AH.27

4 Retractable door seal Carrier: Aluminium anodized Seal profile: Silicone grey, self-extinguishing Supplied with 1 Retractable door seal 2 Fixing brackets with screws Any release plate with screw Protection against cold, draught and vermin Reduces the energy consumption of air conditioning systems Reduces light leakage For soundproofing doors (DIN 49) For smoke control doors according to EN For fire resistant doors according to EN For full mortise fitting Suitable for DIN left hand and DIN right hand Optional with single-side or double-side release Can be prepared for locking bolts or lever action flush bolts Rostproof internal mechanism and anodized carrier Technical Data Max. sealing height: 12 mm Double-side release can be cut to max.: 0 mm Required groove width: 20 mm Sound proofing level with air gap 7 mm: 49 db One-side release can be cut to max. Single-side release 930 mm 584 mm mm 639 mm mm 708 mm mm 833 mm ,030 mm 958 mm ,130 mm 1,083 mm Packing : 1 pc. One-side release can be cut to max. Double-side release 730 mm 639 mm mm 708 mm mm 833 mm ,030 mm 958 mm ,130 mm 1,083 mm Packing : 1 pc. AH.28

5 Retractable door seal One-side release prepared for locking bolt One-side release prepared for lever action flush bolt Single-side release Double-side release 630 mm mm mm mm ,030 mm ,130 mm Double-side release seal with a length of 730 mm can not be shortened Preparation for locking bolt and lever action flush bolt on request Protection against cold, draught and vermin Reduces the energy consumption of air conditioning systems Reduces light leakage For soundproofing doors (DIN 49) For smoke control doors according to EN For fire resistant doors according to EN For full mortise fitting Suitable for DIN left hand and DIN right hand Optional with single-side or double-side release Can be prepared for driving bolt or square bolt Adapts perfectly to any floor condition due to 3-spring mechanism Technical Data Max. sealing height 14 mm Can be shortened at one end by max. 0 mm Required groove width 15 mm Soundproofing level with air gap 6 mm 51 db Carrier: Aluminium Seal profile: Silicone grey, self-extinguishing Supplied with 1 Retractable door seal 2 Fixing brackets with screws Any release plate with screw Omega version Single-side release 708 mm mm mm ,083 mm AH.29

6 Sill protection sweep door seal Protection against cold, draft and vermin For surface mounting under door bottom Material Housing: Aluminium Seal: Solid neoprene Housing: Mill finish Seal: Black 1,000 mm ,000 mm Packing : 1 pc. supplied with fixing material AH.30

7 Sliding door seal Supplied with 1 Door seal 1 Fixing set with magnet Double-side release Sliding door with magnet 833 mm mm ,083 mm ,208 mm Accessories Sliding door without magnet Floor guide, black For sliding doors without locking mechanism Release power only 20 N/m Protection against heat, draught and vermin Reduced the energy consumption of air conditioning systems Reduces light leakage Full mortised fitting Technical data Max. sealing height 11 mm Groove width without floor guide 12 mm Groove width with floor guide 17 mm Minimum door thickness 34 mm Can be shortened on one side to 125 mm Sliding door seal: Aluminium silver coloured Additional fixing set for sliding door without magnet (lock required) Additional magnet for on top of door for additional arrestation (holding force 70N) Additional press plate for magnet AH.31

8 Retractable door seal for glass doors Duo GS Duo GS-H Exterior housing: Aluminium silver coloured anodized Sealing profile: Silicone grey, self-extinguishing installation Installation With silicone adhesive, with VSG only use adhesives and sealants approved by the glass manufacturer With models GS-H the glass height must be 32 mm shorter Models GS must be installed on the opening side Supplied with 1 Automatic door seal 1 Release plate (2 release plates with model DUO) 1 Installation instructions DUO GS Glass thickness Double-side release 708 mm mm mm mm mm mm ,083 mm mm ,208 mm mm For glass doors where sound proofing, smoke protection and fire protection are required Suitable for DIN left hand and DIN right hand Optional with single-end or double-end (DUO) release Silent closing Adjustable sealing height Technical Data Max sealing height: 11 mm Can be shortened at one end up to: 125 mm DUO GS H Glass thickness Single-side release 708 mm mm mm mm mm mm ,083 mm mm ,208 mm mm GS H Glass thickness Single-side release 708 mm mm mm mm mm mm ,083 mm mm ,208 mm mm Packing : 1 pc. AH.32

9 Meeting stile astragal For fixing to lock stile of the active leaf on a pair of double doors Material Housing: Aluminium Brush seal: Polypropylene Housing: Clear anodized Brush seal: Grey For fixing to lock stile of active leaf on a pair of double doors Material Housing: Aluminium Seal: Solid neoprene Housing: Clear anodized Seal: Black 2,250 mm ,750 mm Packing: 1 pc. including fixing screws 2,250 mm ,750 mm Packing: 1 pc. including fixing screws AH.33

10 Information Rebate seals Fixing methods Rebate seals are mounted in the groove of the frame or door. Depending on the type, the bottom part of the seal is inserted directly into the groove (Fig. 1) or the seal must be fitted with a housing (Fig. 2). Paint compatibility Sealing profiles which are painted over or used for renovation purposes must always be tested for their compatibility with the lacquer. Irrespective of the specifications for paint compatibility, testing should always be carried out. Fig. 1 Fig. 2 Sealing shape For rebated or flush doors are generally two different kind of seals used. Fig. 3 is the standard seal for rebated doors. If this seal in used for flush doors the turning point is changed. The door edge will slide over the surface of the sealing. The closing are difficult. The seal in Fig. 4 is special developed for flush doors. Here the edge will flap down the nose of the door seal. Material - PVC Modified elastic polymer Good physical properties Highly flexible Resistant to aging, weathering and ozone Weldable For indoor use Material - TPE Thermoplastic elastomer Good physical and thermal properties No migration of plasticizers Resistant to aging, weathering and ozone Weldable For indoor and outdoor use Fig. 3 Fig. 4 AH.34

11 Rebate seal Concealed fixing of housing with clips Housing is screwed on Retrofitted seal for existing doors Seal for new installations Housing for sealing strip Material Packing Housing for sealing strip Material Packing Aluminium silver colour anodized 5.25 m Aluminium bright 5.25 m Clips Seal strip, blade type Plastic white 25 pieces Plastic black 5.0 m Sealing strip, bulb type Rebate seal only available as individual parts, not as a set. Plastic black 5.0 m Seal for rebated door only available as individual parts, not as a set. AH.35

12 Internal door seal Suitable for water-based and solvent-based lacquers Self-adhesive Thermoplastic elastomer (TPE) Installation Seal gap: 5 mm Rebate width: m For renovation of doors and windows Protection from cold and draught Self adhesive fixing Thermoplastic elastomer (TPE) Installation Seal gap: 4 mm Width: mm White Black Dark brown White Brown Beige Beige Packing: 6 m Packing: 0 m AH.36

13 Internal door seal Protection from cold and draught For flush doors Not suitable for lacquer or alkyd resin lacquer Modified elastic polymer (PVC) Fixing Seal gap: 5 mm Rebate width: 12 mm For rebated doors Not suitable for acrylic lacquer or alkyd resin lacquer Modified elastic polymer (PVC) Fixing Seal gap: 5 mm Rebate width : 12 mm White White Black Black Dark brown Dark brown Brown Beige Beige Ochre-brown Packing: 25 m Packing: 25 m AH.37

14 Internal door seal Protection from cold and draught For rebated doors Not suitable for lacquer or alkyd resin lacquer Modified elastic polymer (PVC) Fixing Seal gap: 4 mm Rebate width: mm For fire protection doors according to DIN 42 Fire resistant, self-extinguishing, expanding Not suitable for PVC lacquer or acrylic resin lacquer The suitability of the material, in connection with the door element, for the application concerned must be proved by individual control Modified elastic polymer (PVC) Fixing Seal gap: 4 mm Rebate width: mm White Dark brown Black Packing: 50 m Dark brown Brown Vario pliers Beige Packing: 25 m Vario pliers All SV/DS seals can be easily be cut to differing frame sizes with the Vario pliers AH.38

15 Entrance door seal Compatible with water-based and solvent-based lacquer Thermoplastic elastomer (TPE) Fixing Seal gap: 5 mm Rebate width: 12 mm Compatible with water-based and solvent-based lacquer Thermoplastic elastomer (TPE) Fixing Seal gap: 5 mm Rebate width: 15 mm White White Black Black Dark brown Dark brown Beige Beige Packing: 25 m Packing: 25 m AH.39

16 Frame seal Door seal For flush doors Not suitable for acrylic lacquer or alkyd resin lacquer Modified elastic polymer (PVC) Fixing Seal gap: mm Put in the slot For rebated doors Not suitable for acrylic lacquer or alkyd resin lacquer Modified elastic polymer (PVC Fixing Seal gap: 2 3 mm Put in the slot Dark brown White Dark brown White Packing: 250 m Packing:350 m AH.40

17 Fire rated door seal For fire rated doors according to UL C Fire rated up to 90 minutes Material Durable, UV-resistant, polyethylene cladding in a brown colour is permanently bonded to resilient urethane foam Installation Seal gap: 9 15 mm Rebate width: 14.7 mm Put strike side, hinge side and header of seal profile into the slot Dark brown Packing: 2,180 mm AH.41