IMITATION SECURITY CAMERA

Transcription

1 IMITATION SECURITY CAMERA ASSEMBLY AND OPERATING INSTRUCTIONS 3491 Mission Oaks Blvd., Camarillo, CA Visit our Web site at Copyright 2005 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call

2 Specifications B atteries Required 3 - AA Overall Dimensions 2 1 / 8 x 5 1 / 4 x 2 1 / 8 Motion Sensor Range 9 1 / 2 U nit Weight 0.4 Lbs. Features: 0-90 Up or Down Tilt, Realistic Motion-Activated Blinking LED and Oscillating Movement Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product! 1. Keep work area clean. Cluttered areas invite injuries. 2. Observe work area conditions. Do not use the Imitation Security Camera in damp or wet locations. Don t expose to rain. Keep work area well lit. Do not use electrically powered products in the presence of flammable gases or liquids. 3. Keep children away. Children must never be allowed in the work area. Do not let them handle the Imitation Security Camera. This product is not a toy. 4. Use the right product for the job. Do not modify this product and do not use this product for a purpose for which it was not intended. 5. Dress properly. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 6. Use eye protection. Always wear ANSI approved impact safety goggles during installation. 7. Maintain with care. Keep the Imitation Security Camera clean for better and safer performance. 8. Stay alert. Watch what you are doing, use common sense. Do not install the Imitation Security Camera when you are tired. Page 2

3 9. Check for damaged parts. Before using the Imitation Security Camera, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not use the Imitation Security Camera if any switch does not turn On and Off properly. 10. Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any other parts will void the warranty. Only use accessories intended for use with this product. Approved accessories are available from Harbor Freight Tools. 11. Do not install the Imitation Security Camera if under the influence of alcohol or drugs. Read warning labels if taking prescription medicine to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not install the unit. 12. Maintenance. For your safety, service and maintenance should be performed regularly by a qualified technician. 13. This unit relies on light to detect motion. This unit will not activate properly if used in a dark or dimly lit place. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking, check to make sure that the product is intact and undamaged. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Page 3

4 Installation 1. Chose a wall or ceiling location that allows you to mount the unit onto a solid surface capable of sustaining the weight of the unit. If you cannot mount to wall studs, you will need to use the appropriate wall mounting anchors (not included). When choosing a mounting location, keep in mind that the motion sensor that has a 9-1/2 foot maximum motion-sensing distance. Note: The mounting holes on the Imitation Security Camera are approx. 1/4 or 6 mm. FIGURE 1 Base Mounting Hole 2 Hold the base of the unit against the surface you are going to mount to, and draw a template of the mounting holes. See FIGURE Check that there are no hidden wires, cables or other obstructions in the mounting location. Predrill the holes. Hold the unit in place and mount the Bolts (included) slowly, by hand. Do not overtighten the Bolts or you may crack the Base of the unit. Operation 1. To turn on the Imitation Security Camera, turn the switch to ON. To deactivate the unit, turn the switch to OFF. See FIGURE While on, the unit will start to rotate and the led will blink for a brief period when the motion sensor detects movement. The unit will then return to a standby mode until movement is detected. Note: Installing and changing batteries are covered on page 5 under Maintenance. FIGURE 2 Movement Track Switch Page 4

5 1. Remove batteries during storage. Maintenance 2. Periodically, place a drop of oil into the movement track to allow the unit to operate freely. 3. If the unit will no longer detect movement, the batteries need to be changed. To change the AA batteries: a. Switch the unit off and remove the cover on the top of the unit. Remove the spent AA batteries and dispose of them properly. b. Replace with fresh AA batteries making sure that the polarities (+ or -) of the batteries line up with the polarity signs as shown in FIGURE 3, below. c. Replace the cover. FIGURE 3 Page 5