! EthIR Switch single port! EthIR Beam with mini-din connector! 110/220 Power supply! Mini-DIN cable to connect the EthIR Beam to the EthIR Switch

Transcription

1

2 Section 1 The (ESB101), (ESB1000), (ESB3011B) and (ESB301) comes equipped with:! EthIR Switch single port! EthIR Beam with mini-din connector! 110/220 supply! Mini-DIN cable to connect the EthIR Beam to the EthIR Switch Note: The (ESB301) comes equipped with an additional Ethernet port for user PC. IMPORTANT NOTE: The single port (ESB101), (ESB1000), (ESB3011B), (ESB301) and Multiport (ESB208/216) are shipped with DHCP enabled. If you connect to a non DHCP network you will experience connection difficulties. Configure the Switch first before uplinking to the network. EthIR Beam EB100 port EthIR Switch (ESB101) and (ESB1000 and ESB3000) For EthIR LAN and EthIR STAR ESB1000 RCA Jack port Uplink port 10 Base-T cable cable cable EthIR Switch ESB301 port Uplink port 10/100 Base-T Ethernet to desktop

3 The (ESB208/216)! The multiport (ESB208) comes equipped with: 8 Infrared ports 8 Ethernet pass-through ports (See Section 3 for more pass-through information)! The multiport (ESB216) comes equipped with: 16 Infrared ports 16 Ethernet pass-through ports (See Section 3 for more pass-through information)! EthIR Beam with RJ45 connector! cable! RJ45 patch cable to connect the EthIR Beam to the EthIR Switch (RJ45 patch cable for 10/100 Base-T Uplink not included) EthIR Beam EB1000 Ethernet pass-through ports RJ45 connector EthIR Switch front view (ES216 shown) Infrared ports 10/100Base-T Uplink Console for troubleshooting (Cable not included)

4 Section 2 The (ESB101, ESB301,ESB1000, ESB3011b and the ESB208/216) are all DHCP enabled. Insure a DHCP server is up and running on the network before uplinking. If there is no DHCP server on the network then do not uplink. You will have to configure the Switch first, before uplinking to the network. Single Port: 1. Connect one end of the mini-din cable to the EthIR Beam and the other end to the mini-din connector on the Switch. 2. Connect one end of the from the Ethernet uplink port on the Switch to an Ethernet wall jack or hub. 3. Connect power jack to the power jack port and plug into a 110/220 electrical outlet. Note: For the (ESB301) connect the additional Ethernet to desktop port to an Ethernet NIC card in your desktop computer (Optional). EthIR Switch (ESB101, ESB1000 and ESB3000) outlet EthIR LAN and EthIR STAR ESB1000 RJ45 wall jack EthIR Beam Button cable Multiport (ESB208/216) A: Housed in multi-user environment such as conference room or class room with one available network wall jack. After configuration is completed, perform the following: 1. Position the Switch where convenient. 2. Connect one end of an enclosed to one of the bottom ports on the EthIR Beam. Repeat for as many EthIR Beams as needed. 3. Uplink the Switch to a wall jack or hub with an RJ45 patch cable (Cat 3 or 5). 4. on the unit by connecting enclosed power cable to a 110/220 electrical outlet.

5 EthIR Switch front view RJ45 wall jack outlet EthIR Beam B: Housed in the network equipment closet. These switches can be placed in the wiring closet to provide either Infrared or Ethernet connectivity to the existing wall jacks. 1. Position Switch in wall rack. 2. Connect the incoming from each office or cubicle wall jack to one of the bottom infrared ports on the Switch. Repeat as needed for each office cubicle requiring infrared support. 3. Connect another from the corresponding top Ethernet pass-through port to the patch panel or hub. Repeat as needed for each office cubicle requiring both Infrared or Ethernet support. (NOTE: if only providing for Infrared connectivity this step can be skipped). 4. Uplink the Switch to the patch panel or hub with an RJ45 patch cable (Cat 3 or 5). 5. on the unit by connecting enclosed power cable to a 110/220 electrical outlet. Ethernet rack EthIR Switch front view (ES216/616 shown) Optional outlet RJ45 wall jacks EthIR Beam or Ethernet card

6 Section 3 Pass-through allows for flexibility of either Infrared or Ethernet connectivity for each office or cubicle wall connection. If the EthIR Switch senses an incoming Ethernet frame it will pass-through the frame to the Ethernet network via the pass-through port. If the EthIR Switch senses an Infrared frame it will convert it to Ethernet and send it to the network via its Uplink port. Troubleshooting Issues A) If the EthIR Switch (all models) fails to obtain IP addresses for connecting devices when it is set in DHCP mode, check the following: There may not be available IP addresses in the DHCP server pool to allocate for the device. Contact the network administrator to verify if the DHCP server is up and running and has enough IP addresses to allocate. If using a multi-port Switch (for example, the 8 port ES208) and attempting to connect 8 devices, the DHCP server must allocate at least 8 IPs for the Switches IP Pool. Example: If the DHCP server can only allocate 4 IP addresses to the Switches IP pool, then only 4 infrared devices will be able to communicate on the network through the Switch. B) When using the (ESB101), (EthIR STAR ) or (ESB301) to connect to the network, the infrared notebook or handheld device fails to communicate over the DHCP enabled network. Check the cabling: The (ESB101, ESB1000 and the ESB3000) will not function in a 100 Base-T only environment. For all EthIR LAN models, except the ESB3011b, insure that a Category 5 Ethernet Patch Cable is used to uplink to the network. Do not use a cross-over cable to connect the Uplink to the network wall jack. For the (ESB301), insure that the in the Uplink port is connected to the network wall jack and not to the Ethernet NIC card in the desktop computer. The Ethernet to Desktop port is for connecting the ESB301 to the desktop and not to the network wall jack. Crossing these two ports will result in a failure for the ESB301 to communicate with the network and the desktop computer. For the (ESB3011b), insure that the b uplink to the P AP is connected and stable. Check all cables and make certain they fit properly into each connection. C) When there is no DHCP server on the network, make sure the correct IP addresses have been configured on the EthIR Switch. For Further Information Contact: Clarinet Systems, Inc. sales@clarinetsys.com Fremont Blvd. support@clarinetsys.com Fremont, CA For updated information on Clarinet Systems products, contacts and FAQ s please visit our web site at Clarinet Systems, Inc. All Rights Reserved. 11/02