USB ADAPTER PLUS Quick Start

Transcription

1 USB ADAPTER PLUS Quick Start Configuration tool for: IFC 100 / 300 (with Pactware) BATCHFLUX 5500 C (with BatchMon Plus) IFC 010 / 090 / 110 and BATCHFLUX 5012 C / 5015 C (with ImoMon Plus) KROHNE

2 CONTENTS USB ADAPTER PLUS 1 General description 3 2 Operation IFC IFC BATCHFLUX 5500 C Converters with ImoCom Notes 13 2

3 USB ADAPTER PLUS GENERAL DESCRIPTION 1 The USB-Adapter Plus is an adapter to read / write all kind of data to many different converters. The following overview shows you which parts and software you need: Signal converter Cable Software IFC 100 and IFC 300 BATCHFLUX 5500 C BATCHFLUX 5500 C with status output Old ImoCom converters, eg BATCHFLUX 5015, IFC 010 Standard cable dubox 2x3-pole > dubox 2x4-pole or IR interface cable Optional cable M12 5-pole > dubox 2x4-pole Optional T-connector M12 5-pole Optional cable M12 8-pole > dubox 2x4-pole Optional T-connector M12 8-pole Optional cable dubox 1x5-pole > 2x4-pole Pactware + DTM + GDC drivers BatchMon Plus ImoMon Plus The scope of delivery includes the USB-Adapter Plus, the cable needed for IFC 100 / 300 and the printed documentation. Optionally you receive a set of connection cables / connectors for connection to BATCHFLUX 5500 and old ImoCom type converters. 3

4 2 OPERATION USB ADAPTER PLUS 2.1 IFC 100 As described in the previous chapter, the USB-Adapter Plus can be used in three ways. Each way is described in a separate section. The standard delivery includes all items you need to use it with an IFC 100 signal converter. Figure 2-1: Connection of adapter to the GDC bus of the IFC Connection room of IFC Cable 2x3-pole > 2x4-pole 3 USB-Adapter Plus Needed software: GDC driver IFC 100 HART DTM Pactware configuration tool INFORMATION! All relevant tools are on the CD and on the website of the manufacturer. Connect the USB connector to your PC, start the relevant program and follow the instructions given on the display. Refer to the documentation of the signal converter for a description of the menu. 4

5 USB ADAPTER PLUS OPERATION IFC 300 The standard delivery includes all items you need to use it with an IFC 300 signal converter. with GDC connection cable Figure 2-2: Connection of adapter to the GDC bus of the IFC Connection room of IFC Cable 2x3-pole > 2x4-pole 3 USB-Adapter Plus with IR interface cable Figure 2-3: Connection of adapter to the IR interface of the IFC Display of IFC IR Interface cable 3 USB-Adapter Plus Needed software: GDC driver IFC 300 HART DTM Pactware configuration tool INFORMATION! All relevant tools are on the CD and on the website of the manufacturer. Connect the USB connector to your PC, start the relevant program and follow the instructions given on the display. Refer to the documentation of the signal converter for a description of the menu. 5

6 2 OPERATION USB ADAPTER PLUS 2.3 BATCHFLUX 5500 C CAUTION! The T-connectors and the cables ( M12 5-pole / 8-pole) are available as an optional package. To order the specific cables notice the items 2, 3 and 5 in the illustration below Figure 2-4: Connection of adapter to the BATCHFLUX 5500 C V supply (to be provided by customer) 2 T-connector (optional); M12 5-pole M12 8-pole (for BATCHFLUX 5500 C with status output) 3 BATCHFLUX 5500 C connector M12 5-pole M12 8-pole (for BATCHFLUX 5500 C with status output) 4 USB-Adapter Plus (standard) 5 Optional cable; M12 5-pole -> 2x4-pole M12 8-pole -> 2x4-pole (for BATCHFLUX 5500 C with status output) Needed software: BatchMon Plus 6

7 USB ADAPTER PLUS OPERATION 2 INFORMATION! All relevant tools are on the website of the manufacturer. Installation procedure: Do NOT connect the USB adapter yet. Install the software KROHNE BatchMon Setup Version 3.x.x. Ignore any error messages about Windows certificates. Connect the USB cable to the computer. The wizard "New hardware found" starts. - Choose "Not now", click 1x on "Next". - Screen "Hardware" opens, click 2x on "Continue". - If hardware is detected, click on "Finish". Message shows "Hardware can be used". Start the BatchMon Plus program once. Close the program and start it again. In the menu, the function "On-line processing" is now enabled. INFORMATION! Next time, just connect the USB-Adapter Plus and start the program. The menu of the BATCHFLUX 5500 C is given on the next pages. 7

8 2 OPERATION USB ADAPTER PLUS Menu C1: Process input No. Function / subfunction Settings / descriptions C1.1 Calibration C1.1 Calibration C1.1.1 Zero calibration Measured zero point (m/s). Use the "calibration" button to calculate a new zero. Calibration procedure takes 30 seconds. C1.1.2 Size entry selection Value (mm), Table (mm, inch) For "Value": manual input of flow meter size in box For "Table": choose from pull down menu in box C1.1.5 GK selection GK, GKL For "GK": value is shown in box For "GKL": value is shown in box C1.1.8 Coil resistance Ω Configured, can be changed. C1.1.9 Field frequency 1/6...2 * line frequency Choose from pull down menu Select settling Standard (predefined), Manual Settling time 0, ,25 (s) Manual input Line frequency 50 or 60 Hz Measurement conductivity Off, On Off: Default Number values Number of measurements taken to calculate the average conductivity (if is switched on). 8

9 USB ADAPTER PLUS OPERATION 2 C1.2 Filter C1.2 Filter C1.2.1 Min. limitation ,001 (m/s) Menu C2: Inputs/outputs (I/O's) The output freezes at this value. C1.2.2 Max. limitation 0, (m/s) The output freezes at this value. C1.2.3 Flow direction Normal direction (default), Reverse direction C1.2.4 Time constant (s) Manual input C1.2.5 Low flow cut off threshold (m/s) C1.2.6 C1.3 Information Low flow cut off hysteresis C1.3 Information Manual input (m/s) Manual input No. Function / subfunction Settings / descriptions C2.1 Hardware C2.1.0 Hardware Frequency output, Pulse output C2.1.1 Terminals D Program frequency output in submenu Program pulse output in submenu C2.2 Frequency output (if selected in "hardware") C2.2.1 Pulse shape Symmetric, Fixed, Automatic (default) C2.2.2 Pulse width 5E (s) C % pulse rate 0, (Hz) C2.2.4 Range min. -1E E +30 (m 3 /s) Manual input. C2.2.5 Range max. -1E E +30 (m 3 /s) Manual input. C2.2.6 Polarity Both polarity, Positive polarity (default), Negative polarity, Absolute polarity C2.2.7 Limitation min. -1E E +30 (%) C2.2.8 Limitation max. -1E E +30 (%) C2.2.9 Low flow cut off threshold (%) Manual input. C Low flow cut off hysteresis (%) Manual input. C Time constant (s) C Invert signal Off (default), On 9

10 2 OPERATION USB ADAPTER PLUS No. Function / subfunction Settings / descriptions C Delay low flow cutoff [s] Menu C3: Device Manual input. C2.2 Pulse output (if selected in "hardware") C2.2.1 Pulse shape Symmetric, Fixed, Automatic (default) C2.2.2 Pulse width 5E (s) C2.2.6 Polarity Both polarity, Positive polarity (default), Negative polarity, Absolute polarity C Time constant (s) C Invert signal Off (default), On C Max. pulse rate 0, (Hz) C Value per pulse -1E E +30 (m 3 ) C Low flow cut off threshold -1E E +30 (m 3 /s) Manual input C Low flow cut off -1E E +30 (m 3 /s) hysteresis Manual input C Delay low flow cutoff [s] Manual input. C2.3 Status output (not available in BATCHFLUX 5500 C Standard version) C2.3.1 Mode Off, error, flow direction (default) C2.3.2 Invert signal Off (default), on No. Function / subfunction Settings / descriptions C3.1 Units C3.1.1 Volume flow l/s, l/min, l/h, m 3 /s, m 3 /min, m 3 /h, ft 3 /s, ft 3 /min, ft 3 /h, gal/s, gal/min, gal/h, lg/min, lg/h, free unit When you choose "free unit" two additional boxes will appear: box (text free unit) and box (m 3 /s * factor). With this factor the BATCHFLUX will calculate the right value for your free unit. C3.1.4 Volume ml, l, hl, m 3, in 3, ft 3, yd 3, gal, lg, free unit When you choose free unit two additional boxes will appear: box (text free unit) and box (m 3 * factor). With this factor the BATCHFLUX will calculate the right value for your free unit. C3.1.7 Flow speed ft/s, m/s (default) 10

11 USB ADAPTER PLUS OPERATION 2 Menu C4: Service No. Function / subfunction C4.1 Oscillograph Horizontal axis is the quantity of collected values. Vertical axis is the flow rate in liters per seconde C4.2 Sensor values C4.2.1 Flow velocity C4.2.2 DC voltage electrode 2 C4.2.3 DC voltage electrode 3 C4.2.4 Electronic temperature C4.2.5 Field current settling time C4.2.6 Field current resistance C4.2.7 Status sensor C4.2.8 Status starting phase C4.2.9 Status warnings C Status fatal C Status field current C Coil temperature C Conductivity C4.3 Information C4.3.1 Operating hour meter Days, hours, minutes 11

12 2 OPERATION USB ADAPTER PLUS 2.4 Converters with ImoCom Old converters can be used if they have an ImoCom connector on board. Some possibilities are shown below. Figure 2-5: 1 BATCHFLUX 5012 C / 5015 C flowmeter 2 IFC 010 signal converter 3 IFC 090 signal converter 4 IFC 110 signal converter 5 USB-Adapter Plus 6 Optional cable (1x5-pole connector > 2x4-pole connector) CAUTION! Please note that ".net Framework 2.0" is installed before installation (part of Windows XP service pack 2). The ImoCom cable 1x5-pole connector > 2x4-pole connector is available as an optional package. Needed software: ImoMon Plus INFORMATION! All relevant tools are on the CD and on the website of the manufacturer. Connect the USB connector to your PC, start the relevant program and follow the instructions given on the display. 12

13 USB ADAPTER PLUS NOTES 3 13

14 3 NOTES USB ADAPTER PLUS 14

15 USB ADAPTER PLUS NOTES 3 15

16 KROHNE product overview KROHNE - Subject to change without notice. Electromagnetic flowmeters Variable area flowmeters Ultrasonic flowmeters Mass flowmeters Vortex flowmeters Flow controllers Level meters Temperature assemblies Pressure transmitters Analysis products Products and systems for the oil & gas industry Measuring systems for the marine industry Head Office KROHNE Messtechnik GmbH Ludwig-Krohne-Str Duisburg (Germany) Tel.: Fax: info@krohne.com The current list of all KROHNE contacts and addresses can be found at: