LOCALMAP 100 Cable Tester Identifier Kit 234 Identifier Kit 5678 LOCALMAP 100 Carry Case

Size: px

Start display at page:

Download "LOCALMAP 100 Cable Tester Identifier Kit 234 Identifier Kit 5678 LOCALMAP 100 Carry Case"

Stanley Holt
7 years ago
Views:

1 JULY 99 TS0A TS TS TS LOCALMAP 00 Cable Tester Identifier Kit Identifier Kit 578 LOCALMAP 00 Carry Case FAULTS/ CABLE LD. - 8 / /8 /5 7/8 PAIRS TEST GREEN - PASS RED - FAIL O-OPEN S-SHORT R-REVERSED PUSH TO TEST FAULT CODES SP-SPLIT PAIRS C-CROSSED PAIRS B-LOW BATTERY CUSTOMER SUPPORT INFORMATION Order toll-free in the U.S. hours, 7 A.M. Monday to midnight Friday: BBOX FREE technical support, hours a day, 7 days a week: Call or fax Mail order: Black Box Corporation, 000 Park Drive, Lawrence, PA Web site: info@blackbox.com

2 LOCALMAP 00 Cable Tester Chapter Contents Page. Specifications Introduction Operation

3 . Specifications CHAPTER : Specifications Display Single-digit -segment Indicators (8) LEDs: () red fail, () green pass Power Main unit (TS0A): () 9-volt alkaline battery; Remote units (TS, TS): none Size TS0A:."H x.8"w x.7"d (. x 7. x 9. cm); TS, TS: 0.5"H x."d x."w (. x.8 x. cm) Weight TS0A: lb. (. kg)

9-volt alkaline battery; Remote units (TS, TS): none Size TS0A:."H x.8"w x.

4 LOCALMAP 00 Cable Tester. Introduction The LOCALMAP 00 Cable Tester (TS0A) is a simple, inexpensive means to test all types of wiring faults found in 0BASE-T cabling. In addition to identifying wiring faults such as open pairs, shorted pairs, crossed pairs, reversed pairs, and split pairs, the LOCALMAP 00 can also verify and identify up to eight cables. The Identifier Kit (TS) is an identifier kit for the LOCALMAP 00. It contains additional remote units and allows the user to test up to cables without having two people perform the tests. Units are labeled,, and to enable the technician to identify and test additional twisted-pair segments. The Identifier Kit 578 (TS) is an identifier kit for the LOCALMAP 00 unit. It contains additional remote units and allows the user to test up to 8 cables (when used with kit TS) without having two people perform the tests. Units are labeled 5,, 7, and 8 to enable the technician to identify and test additional twisted pair segments. The TS is a carrying case for the LOCALMAP 00 and the remote unit kits (TS and TS).

The Identifier Kit (TS) is an identifier kit for the LOCALMAP 00. It contains additional remote units and allows the user to test up to cables without having two people perform the tests.

5 CHAPTER : Operation. Operation. Cable Tester The LOCALMAP 00 Cable Tester is extremely easy to use. A large display flashes fault codes when a fault exists and indicates the number of the cable it is testing. The remote unit inserts into the wall jack and the Tester connects to the other end of the cable. When you push the start button, the unit automatically runs all the tests and then turns itself off. Green LEDs indicate that pairs /, /, /5, and 7/8 are wired correctly (per EIA 58). Red LEDs indicate failure. The large display signifies the particular type of fault. The fault codes are printed on the front of the unit and are as shown in Figure. -. Some examples of common faults appear in Figures -. OPEN PAIR SPLIT PAIRS (The display will briefly show S, then P) SHORTED PAIR CROSSED PAIR REVERSED PAIR LOW BATTERY Fig. -. Fault Codes. 5

The remote unit inserts into the wall jack and the Tester connects to the other end of the cable. When you push the start button, the unit automatically runs all the tests and then turns itself off.

6 LOCALMAP 00 Cable Tester OPEN PAIR REVERSED PAIR SHORTED PAIR SPLIT PAIRS (LEDs for pairs / & /5 return to green at end of test) SHORT BETWEEN PAIRS (LEDs flash at end of test for both pairs) OPEN/SHORT BETWEEN PAIRS (LEDs flash at end of test for pair / only) CROSSED PAIRS Fig. -. Examples and : Common Faults.. Cable Identifier The Cable Identifier is equally simple to use. You can use up to eight remote units with each remote unit having its own identification number. For example, if the number remote is inserted into a particular wall jack and the Cable Tester is plugged into the other end of the cable. The large display will show the number in addition to providing all the FAULT CODES. So, by using the unique remote units, wire fault finding, cable identification, and cable verification becomes a oneperson operation. If all pairs are open and/or shorted, the cablelocator feature will not function. When the battery voltage becomes low, the display will flash the letter L four times in rapid succession. Replace the battery when this happens, because the unit will not operate properly with a low battery. Under certain conditions, you may get a reading error (such as wrong remote indication because of impedance anomalies and Low Battery indication because of an over-voltage condition). The unit will flash a V in response to overvoltage from a live telco line. Use a short RJ-5/RJ-5 adapter cable to relieve the strain on the RJ-5 connector mounted in the Tester.

You can use up to eight remote units with each remote unit having its own identification number.

FlexPoint T1/E1 Copper to Fiber Line Driver

BLACK BOX NETWORK SERVICES MT660A-MM MT661A-SM MT660A-MM-E MT661A-SM-E FlexPoint T1/E1 Copper to Fiber Line Driver CUSTOMER Order toll-free in the U.S.: Call 877-877-BBOX SUPPORT (outside U.S. call 724-746-5500)